Results for “Crystal engineering” — Page 18

NASA NTRS1995

Hydrogen Annealing Of Single-Crystal Superalloys

Annealing at temperature equal to or greater than 2,200 degrees F in atmosphere of hydrogen found to increase ability of single-crystal superalloys to resist oxidation when subsequently exposed to oxidizing atmospheres at temperatures almost as high. Supperalloys in question are principal constituents of hot-stage airfoils (blades) in aircraft and ground-based turbine engines; also used in other high-temperature applications like chemical-processing plants, coal-gasification plants, petrochemical refineries, and boilers. Hydrogen anneal provides resistance to oxidation without decreasing fatigue strength and without need for coating or reactive sulfur-gettering constituents. In comparison with coating, hydrogen annealing costs less. Benefits extend to stainless steels, nickel/chromium, and nickel-base alloys, subject to same scale-adhesion and oxidation-resistance considerations, except that scale is chromia instead of alumina.

Smialek, James L.↗

NASA NTRS1986

Orientation and temperature dependence of some mechanical properties of the single-crystal nickel-base superalloy Rene N4. I - Tensile behavior

Single crystal specimens of a nickel-base superalloy with axes near 001, 011, and -112 were tested in tension at room temperature, 760, and 980 C. The alloy Rene N-4, was developed for gas turbine engine blades and has the nominal composition 3.7 Al, 4.2 Ti, 4 Ta, 0.5 Nb, 6 W, 1.5 Mo, 9 Cr, 7.5 Co, balance Ni, (all in weight percent). Analysis of slip band traces, specimen axis rotation, and dislocation Burgers vectors showed that at 760 and 980 C primary cube slip supplanted normal octahedral slip for the -112 line-oriented specimens. The other two orientations, which have lower resolved shear stresses on the cube system, exhibited octahedral slip at all three temperatures. The critical resolved shear stress is considerably greater on the cube system than on the octahedral system at room temperature. However, at 760 and 980 C the critical resolved shear stresses on the two systems are about the same. While the room temperature and 980 C yield strengths for the two orientations exhibiting octahedral slip could be rationalized on the basis of resolved shear stress, those at 760 C could not. Such violations of Schmid's law have previously been observed in other superalloys and single phase gamma-prime.

Miner, R. V.↗

NASA NTRS2015

An Overview of SBIR Phase 2 Physical Sciences and Biomedical Technologies in Space

Technological innovation is the overall focus of NASA's Small Business Innovation Research (SBIR) program. The program invests in the development of innovative concepts and technologies to help NASA's mission directorates address critical research and development needs for agency projects. This report highlights innovative SBIR Phase II projects from 2007-2012 specifically addressing areas in physical sciences and biomedical technologies in space, which is one of six core competencies at NASA Glenn Research Center. There are twenty two technologies featured with emphasis on a wide spectrum of applications such as reusable handheld electrolyte, sensor for bone markers, wideband single crystal transducer, mini treadmill for musculoskeletal, and much more. Each article in this report describes an innovation, technical objective, and highlights NASA commercial and industrial applications. This report serves as an opportunity for NASA personnel including engineers, researchers, and program managers to learn of NASA SBIR's capabilities that might be crosscutting into this technology area. As the result, it would cause collaborations and partnerships between the small companies and NASA Programs and Projects resulting in benefit to both SBIR companies and NASA.

electrolytes↗

NASA NTRS2023

Thermomechanical Property Prediction of Amorphous and Crystal PEKK via Molecular Dynamics

Traditionally, advanced aerospace composites have been manufactured using thermoset resins. However, recently, thermoplastics have been investigated for use in the manufacturing of composite materials due to their unique manufacturing characteristics. Thermoplastic resins can be reshaped and formed, along with the added benefit of being recyclable, which thermoset resin cannot. Thermoplastic materials undergo a crystallization process during manufacturing which affects the percent crystallinity of the material. The crystallization needs to be understood better to maximize the potential of thermoplastic resins. PEKK is a thermoplastic material with good chemical, thermal, and mechanical loading resistance. PEKK is also a material NASA is interested in for developing new bonded joint technology. The crystalline microstructure of PEKK is at the micrometer length scale, and it is of interest to model the effects of the crystallinity structure on PEKK’s bulk properties. Molecular dynamics (MD) is a simulation tool that allows for property-structure relationships between atomistic structure and nanometer-length portions of a material. This makes MD a useful tool for developing the structure-property relationship of PEKK. However, the micrometer length scale of PEKK’s crystal structure is too large for MD. Thus, a hybrid approach to modeling PEKK’s microstructure is proposed in this work where MD models are built of both the amorphous and crystalline phases of PEKK. The engineering material properties can be obtained using MD at the nanometer length scale. A micromechanics approach can then generate the micrometer length scale of the crystallinity and the effective properties can be homogenized. The objective of this paper is to show the MD model workflow and the MD-predicted properties of PEKK. The properties can then be homogenized with different crystalline percentages to build design graphs that can be used to tailor PEKK for specific composite applications.

poly ether ketone ketone↗

NASA NTRS1993

Chemical Vapor Deposition Of Silicon Carbide

Large single-crystal SiC boules from which wafers of large area cut now being produced commerically. Availability of wafers opens door for development of SiC semiconductor devices. Recently developed chemical vapor deposition (CVD) process produces thin single-crystal SiC films on SiC wafers. Essential step in sequence of steps used to fabricate semiconductor devices. Further development required for specific devices. Some potential high-temperature applications include sensors and control electronics for advanced turbine engines and automobile engines, power electronics for electromechanical actuators for advanced aircraft and for space power systems, and equipment used in drilling of deep wells. High-frequency applications include communication systems, high-speed computers, and microwave power transistors. High-radiation applications include sensors and controls for nuclear reactors.

Powell, J. Anthony↗

NASA NTRS1999

Application of Single Crystal Failure Criteria: Theory and Turbine Blade Case Study

The orientation of the single crystal material within a structural component is known to affect the strength and life of the part. The first stage blade of the High Pressure Fuel Turbopump (HPFTP)/ Alternative Turbopump Development (ATD), of the Space Shuttle Main Engine (SSME) was used to study the effects of secondary axis'orientation angles on the failure rate of the blade. A new failure criterion was developed based on normal and shear strains on the primary crystallographic planes. The criterion was verified using low cycle fatigue (LCF) specimen data and a finite element model of the test specimens. The criterion was then used to study ATD/HPFTP first stage blade failure events. A detailed ANSYS finite element model of the blade was used to calculate the failure parameter for the different crystallographic orientations. A total of 297 cases were run to cover a wide range of acceptable orientations within the blade. Those orientations are related to the base crystallographic coordinate system that was created in the ANSYS finite element model. Contour plots of the criterion as a function of orientation for the blade tip and attachment were obtained. Results of the analysis revealed a 40% increase in the failure parameter due to changing of the primary and secondary axes of material orientations. A comparison between failure criterion predictions and actual engine test data was then conducted. The engine test data comes from two ATD/HPFTP builds (units F3- 4B and F6-5D), which were ground tested on the SSME at the Stennis Space Center in Mississippi. Both units experienced cracking of the airfoil tips in multiple blades, but only a few cracks grew all the way across the wall of the hollow core airfoil.

Sayyah, Tarek↗

NASA NTRSDate not supplied

Obtaining cryogenic molecular transport data for analysis

The James Webb Space Telescope (JWST) has a primary mirror, made of 18 segments, and a secondary mirror (SM) that are used to direct the light of desired targets. While on orbit, the secondary mirror assembly (SMA) was stowed for approximately 10 days and was subject to molecular contamination outgassing from the cavity of the secondary mirror support structure (SMSS) in-board hinge (IBH) which contains cables, motors, resolvers, and coatings. The main concern during this period before SMA deployment is the accumulation of ice due to the lack of a heater on the SMA. The temperature differentials between the IBH surfaces and SMA could cause redistribution of contaminants. To address this concern, single layer insulation (SLI) was used to create adequate venting and path redirection of outgassing from the IBH. Two separate thermal vacuum tests were performed to quantify this contamination: one Z307 ASTM E 1559 materials test of the radiator paint used on the motor of the IBH and a separate test on a primary mirror backplane assembly (PMBA) qualification engineering test unit (ETU) of the IBH. These tests approximately followed the predicted SMA pre-deployment thermal environment. To quantify source rates in case of a leak, the motor and resolver sides were separated and quartz crystal microbalances (QCM) were used to measure the deposition of water. The SLI redesign and implementation and outgassing measurements to understand leak effects from the IBH were essential to mitigate the deposition of contamination on the SMA.

James Webb Space Telescope, contamination, cleanro↗

NASA NTRSDate not supplied

Obtaining Cryogenic Molecular Transport Data for Analysis

The James Webb Space Telescope (JWST) has a primary mirror, made of 18 segments, and a secondary mirror (SM) that are used to direct the light of desired targets. While on orbit, the secondary mirror assembly (SMA) was stowed for approximately 10 days and was subject to molecular contamination outgassing from the cavity of the secondary mirror support structure (SMSS) in-board hinge (IBH) which contains cables, motors, resolvers, and coatings. The main concern during this period before SMA deployment is the accumulation of ice due to the lack of a heater on the SMA. The temperature differentials between the IBH surfaces and SMA could cause redistribution of contaminants. To address this concern, single layer insulation (SLI) was used to create adequate venting and path redirection of outgassing from the IBH. Two separate thermal vacuum tests were performed to quantify this contamination: one Z307 ASTM E 1559 materials test of the radiator paint used on the motor of the IBH and a separate test on a primary mirror backplane assembly (PMBA) qualification engineering test unit (ETU) of the IBH. These tests approximately followed the predicted SMA pre-deployment thermal environment. To quantify source rates in case of a leak, the motor and resolver sides were separated and quartz crystal microbalances (QCM) were used to measure the deposition of water. The SLI redesign and implementation and outgassing measurements to understand leak effects from the IBH were essential to mitigate the deposition of contamination on the SMA. "

James Webb Space Telescope↗

NASA NTRS2024

Molecular Dynamics Simulations of Microstructural Effects on Austenite-Martensite Interfaces in NiTi

Formation and migration of austenite-martensite interfaces plays the key role in reversible martensitic transformations of shape memory alloys (SMAs). How these interfaces interact with the SMA microstructure is a primary determining factor in important functional properties such as hysteresis and transformation span. As such, successful microstructural engineering of SMAs requires in-depth knowledge of interface behavior. The rapid nature of martensitic transformations makes experimental observations of moving austenite-martensite interfaces challenging. Molecular dynamics (MD) simulation is a unique tool which can probe the atomic-scale details of austenite-martensite interfaces as they migrate through different microstructures. However, in focusing on the entire transformation process, including the nucleation of new phases, MD studies are usually performed so far from equilibrium that their relevance to experiment is questionable. Here, we demonstrate new MD techniques to generate energetically preferred austenite-martensite interfaces in NiTi under near-equilibrium conditions. The interfaces are semi-coherent, exhibiting a series of structural disconnections, and they can migrate rapidly through single crystals under only small thermodynamic driving forces. In contrast, when interfaces migrate in polycrystals, their motion is impeded by thermoelastic effects as well as changes in orientation relationships at grain boundaries. Microstructures which accumulate large amounts of elastic energy tend to release some fraction through irreversible, hysteresis-inducing mechanisms. We demonstrate that engineering microstructures with less constraints is a viable strategy to produce SMAs with reduced hysteresis and transformation span. Similar thermoelastic and hysteresis-inducing mechanisms also arise when austenite-martensite interfaces encounter precipitates and can be controlled by tuning characteristics of the precipitate distribution.

Gabriel Plummer↗

NASA NTRSDate not supplied

Molecular Dynamics Simulations of Microstructural Effects on Austenite-Martensite Interfaces in NiTi

The formation and migration of austenite-martensite interfaces plays the key role in reversible martensitic transformations of shape memory alloys (SMAs). How these interfaces interact with the SMA microstructure is a primary determining factor in important functional properties such as hysteresis and transformation span. As such, successful microstructural engineering of SMAs requires in-depth knowledge of interface behavior. The rapid nature of martensitic transformations makes experimental observations of moving austenite-martensite interfaces challenging. Molecular dynamics (MD) simulation is a unique tool which can probe the atomic-scale details of austenite-martensite interfaces as they migrate through different microstructures. However, in focusing on the entire transformation process, including the nucleation of new phases, MD studies are usually performed so far from equilibrium that their relevance to experiment is questionable. Here, we demonstrate new MD techniques to generate energetically preferred austenite-martensite interfaces in NiTi under near-equilibrium conditions. The interfaces are semi-coherent, exhibiting a series of structural disconnections, and they can migrate rapidly through single crystals under only small thermodynamic driving forces. In contrast, when interfaces migrate in polycrystals, their motion is impeded by thermoelastic effects as well as changes in orientation relationships at grain boundaries. Microstructures which accumulate large amounts of elastic energy tend to release some fraction through irreversible, hysteresis-inducing mechanisms. We demonstrate that engineering microstructures with less constraints is a viable strategy to produce SMAs with reduced hysteresis and transformation span. Similar thermoelastic and hysteresis-inducing mechanisms also arise when austenite-martensite interfaces encounter precipitates and can be controlled by tuning characteristics of the precipitate distribution.

Gabriel Plummer↗

NASA NTRSDate not supplied

Molecular Dynamics Simulations of Microstructural Effects on Austenite-Martensite Interfaces in NiTi

Formation and migration of austenite-martensite interfaces plays the key role in reversible martensitic transformations of shape memory alloys (SMAs). How these interfaces interact with the SMA microstructure is a primary determining factor in important functional properties such as hysteresis and transformation span. As such, successful microstructural engineering of SMAs requires in-depth knowledge of interface behavior. The rapid nature of martensitic transformations makes experimental observations of moving austenite-martensite interfaces challenging. Molecular dynamics (MD) simulation is a unique tool which can probe the atomic-scale details of austenite-martensite interfaces as they migrate through different microstructures. However, in focusing on the entire transformation process, including the nucleation of new phases, MD studies are usually performed so far from equilibrium that their relevance to experiment is questionable. Here, we demonstrate new MD techniques to generate energetically preferred austenite-martensite interfaces in NiTi under near-equilibrium conditions. The interfaces are semi-coherent, exhibiting a series of structural disconnections, and they can migrate rapidly through single crystals under only small thermodynamic driving forces. In contrast, when interfaces migrate in polycrystals, their motion is impeded by thermoelastic effects as well as changes in orientation relationships at grain boundaries. Microstructures which accumulate large amounts of elastic energy tend to release some fraction through irreversible, hysteresis-inducing mechanisms. We demonstrate that engineering microstructures with less constraints is a viable strategy to produce SMAs with reduced hysteresis and transformation span. Similar thermoelastic and hysteresis-inducing mechanisms also arise when austenite-martensite interfaces encounter precipitates and can be controlled by tuning characteristics of the precipitate distribution.

Gabriel Plummer↗

NASA NTRS2012

Characterization of the Vectron PX-570 Crystal Oscillator for Use in Harsh Environments

Computing hardware, data-acquisition systems, communications systems, and many electronic control systems require well-controlled timing signals for proper and accurate operation. These signals are, in most cases, provided by circuits that employ crystal oscillators due to availability, cost, ease of operation, and accuracy. In some cases, the electronic systems are expected to survive and operate under harsh conditions that include exposure to extreme temperatures. These applications exist in terrestrial systems as well as in aerospace products. Well-logging, geothermal systems, and industrial process control are examples of ground-based applications, while distributed jet engine control in aircraft, space-based observatories (such as the James Webb Space Telescope), satellites, and lunar and planetary landers are typical environments where electronics are exposed to harsh operating conditions. To ensure these devices produce reliable results, the digital heartbeat from the oscillator must deliver a stable signal that is not affected by external temperature or other conditions. One such solution is a recently introduced commercial-off-the-shelf (COTS) oscillator, the PX-570 series from Vectron International. The oscillator was designed for high-temperature applications and as proof, the crystal oscillator was subjected to a wide suite of tests to determine its ruggedness for operation in harsh environments. The tests performed by Vectron included electrical characterization under wide range of temperature, accelerated life test/aging, shock and vibration, internal moisture analysis, ESD threshold, and latch-up testing. The parametric evaluation was performed on the oscillator's frequency, output signal rise and fall times, duty cycle, and supply current over the temperature range of -125 C to +230 C. The evaluations also determined the effects of thermal cycling and the oscillator's re-start capability at extreme hot and cold temperatures. These thermal cycling and restart tests were performed at the NASA Glenn Research Center. Overall, the crystal oscillator performed well and demonstrated very good frequency stability. This paper will discuss the test procedures and present details of the performance results.

Li, Jacob↗

NASA NTRS1980

Space processing applications rocket project SPAR 4, engineering report

The materials processing experiments in space, conducted on the SPAR 4 Black Brant VC rocket, are described and discussed. The SPAR 4 payload configuration, the rocket performance, and the flight sequence are reported. The results, analyses, and anomalies of the four experiments are discussed. The experiments conducted were the uniform dispersions of crystallization processing, the contained polycrstalline solidification in low gravity, the containerless processing of ferromagnetic materials, and the containerless processing technology. The instrumentation operations, payload power relay anomaly, relay postflight operational test, and relay postflight shock test are reported.

Reeves, F.↗

NASA NTRS1988

NLF technology is ready to go

Natural laminar flow (NLF) can reduce drag on aircraft developed using modern structural design methods. Modern metal and composite construction methods can meet NLF requirements for subsonic commuter and business airframes. NLF research at NASA concentrates on expanding the practical application of NLF drag reduction technology; payoffs include progress with liquid-crystal flow visualization, NLF on three-dimensional bodies, and the effects of acoustics on laminar stability. Fuel savings from 2 to 4 percent are expected if laminar flow could be achieved over the forward 50 percent of engine nacelles on large transports depending on the configuration. It is concluded that the skill required to use NLF for drag reduction depends on understanding the conservative design corridors within which laminar flow is durable and reliable.

Holmes, Bruce J.↗

NASA NTRS2002

A large iris-like expansion of a mechanosensitive channel protein induced by membrane tension

MscL, a bacterial mechanosensitive channel of large conductance, is the first structurally characterized mechanosensor protein. Molecular models of its gating mechanisms are tested here. Disulfide crosslinking shows that M1 transmembrane alpha-helices in MscL of resting Escherichia coli are arranged similarly to those in the crystal structure of MscL from Mycobacterium tuberculosis. An expanded conformation was trapped in osmotically shocked cells by the specific bridging between Cys 20 and Cys 36 of adjacent M1 helices. These bridges stabilized the open channel. Disulfide bonds engineered between the M1 and M2 helices of adjacent subunits (Cys 32-Cys 81) do not prevent channel gating. These findings support gating models in which interactions between M1 and M2 of adjacent subunits remain unaltered while their tilts simultaneously increase. The MscL barrel, therefore, undergoes a large concerted iris-like expansion and flattening when perturbed by membrane tension.

NASA Discipline Cell Biology↗

NASA NTRS1988

Fatigue life prediction modeling for turbine hot section materials

A major objective of the fatigue and fracture efforts under the Hot Section Technology (HOST) program was to significantly improve the analytic life prediction tools used by the aeronautical gas turbine engine industry. This was achieved in the areas of high-temperature thermal and mechanical fatigue of bare and coated high-temperature superalloys. The cyclic crack initiation and propagation resistance of nominally isotropic polycrystalline and highly anisotropic single crystal alloys were addressed. Life prediction modeling efforts were devoted to creep-fatigue interaction, oxidation, coatings interactions, multiaxiality of stress-strain states, mean stress effects, cumulative damage, and thermomechanical fatigue. The fatigue crack initiation life models developed to date include the Cyclic Damage Accumulation (CDA) and the Total Strain Version of Strainrange Partitioning (TS-SRP) for nominally isotropic materials, and the Tensile Hysteretic Energy Model for anisotropic superalloys. A fatigue model is being developed based upon the concepts of Path-Independent Integrals (PII) for describing cyclic crack growth under complex nonlinear response at the crack tip due to thermomechanical loading conditions. A micromechanistic oxidation crack extension model was derived. The models are described and discussed.

Halford, G. R.↗

NASA NTRS1989

Fatigue life prediction modeling for turbine hot section materials

A major objective of the fatigue and fracture efforts under the NASA Hot Section Technology (HOST) program was to significantly improve the analytic life prediction tools used by the aeronautical gas turbine engine industry. This was achieved in the areas of high-temperature thermal and mechanical fatigue of bare and coated high-temperature superalloys. The cyclic crack initiation and propagation resistance of nominally isotropic polycrystalline and highly anisotropic single crystal alloys were addressed. Life prediction modeling efforts were devoted to creep-fatigue interaction, oxidation, coatings interactions, multiaxiality of stress-strain states, mean stress effects, cumulative damage, and thermomechanical fatigue. The fatigue crack initiation life models developed to date include the Cyclic Damage Accumulation (CDA) and the Total Strain Version of Strainrange Partitioning (TS-SRP) for nominally isotropic materials, and the Tensile Hysteretic Energy Model for anisotropic superalloys. A fatigue model is being developed based upon the concepts of Path-Independent Integrals (PII) for describing cyclic crack growth under complex nonlinear response at the crack tip due to thermomechanical loading conditions. A micromechanistic oxidation crack extension model was derived. The models are described and discussed.

G R Halford↗

NASA NTRS1996

Thermal and Structural Analysis Conducted on Hollow-Core Turbine Blade of the Space Shuttle Main Engine

Hot-section components of spacecraft engines are exposed to severe thermal-structural loading conditions, especially during the startup and shutdown portions of the engine cycle. For instance, the thermal transient during startup within the space shuttle main engine (SSME) can lead to a gas temperatures in excess of 3000 C, affecting the operating life of key components, such as the turbine blades. To improve the durability of these components and in particular the turbine blade, single crystal superalloys have been considered. PWA-1480, a nickel-base superalloy, has been used as the turbine blade material for the Alternate Turbopump Development (ATD) program for the SSME.

Source record↗