Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Control design”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18
All sourcesNASA NTRSDOE OSTI
NASA NTRS2003

Disturbance Reduction Control Design for the ST7 Flight Validation Experiment

The Space Technology 7 experiment will perform an on-orbit system-level validation of two specific Disturbance Reduction System technologies: a gravitational reference sensor employing a free-floating test mass, and a set of micro-Newton colloidal thrusters. The ST7 Disturbance Reduction System is designed to maintain the spacecraft's position with respect to a free-floating test mass to less than 10 nm/Hz, over the frequency range of 1 to 30 mHz. This paper presents the design and analysis of the coupled, drag-free and attitude control systems that close the loop between the gravitational reference sensor and the micro-Newton thrusters, while incorporating star tracker data at low frequencies. A full 18 degree-of-freedom model, which incorporates rigid-body models of the spacecraft and two test masses, is used to evaluate the effects of actuation and measurement noise and disturbances on the performance of the drag-free system.

Maghami, P. G.↗
NASA NTRS1992

Thermal control design of the Lightning Mapper Sensor narrow-band spectral filter

The performance of the Lightning Mapper Sensor is dependent on the temperature shifts of its narrowband spectral filter. To perform over a 10 degree FOV with an 0.8 nm bandwidth, the filter must be 15 cm in diameter and mounted externally to the telescope optics. The filter thermal control required a filter design optimized for minimum bandpass shift with temperature, a thermal analysis of substrate materials for maximum temperature uniformity, and a thermal radiation analysis to determine the parameter sensitivity of the radiation shield for the filter, the filter thermal recovery time after occultation, and heater power to maintain filter performance in the earth-staring geosynchronous environment.

Flannery, Martin R.↗
NASA NTRS1971

Space shuttle guidance, navigation and control design equations, volume 1

Revised documentation is presented pertaining to the computation requirements for guidance, navigation, and control of the space shuttle orbiter vehicle. Separate sections cover the following areas; (1) reference documents, (2) GN and C system description, (3) GN and C software functional requirements, and (4) coordinate systems and transformations.

Cox, K. J.↗
NASA NTRS1974

Digital adaptive flight control design using single stage model following indices

Simple mechanical linkages are often unable to cope with many control problems associated with high-performance aircraft. This has led to the development of digital fly-by-wire control systems and in particular digital adaptive controllers that can be efficiently adjusted during system operation. To this effect, a control law has been derived based upon the minimization of a single-stage weighted combination of control energy and the squared error between the states of a linear plant and model. This control logic is interfaced with an on-line weighted least-squares estimator and a Kalman state filter. The utility of the resultant control system is illustrated by its application to the linearized dynamics of a typical fighter aircraft.

Alag, G.↗
NASA NTRS1986

Large-Scale Advanced Prop-Fan (LAP) pitch change actuator and control design report

In recent years, considerable attention has been directed toward improving aircraft fuel consumption. Studies have shown that the high inherent efficiency previously demonstrated by low speed turboprop propulsion systems may now be extended to today's higher speed aircraft if advanced high-speed propeller blades having thin airfoils and aerodynamic sweep are utilized. Hamilton Standard has designed a 9-foot diameter single-rotation Large-Scale Advanced Prop-Fan (LAP) which will be tested on a static test stand, in a high speed wind tunnel and on a research aircraft. The major objective of this testing is to establish the structural integrity of large-scale Prop-Fans of advanced construction in addition to the evaluation of aerodynamic performance and aeroacoustic design. This report describes the operation, design features and actual hardware of the (LAP) Prop-Fan pitch control system. The pitch control system which controls blade angle and propeller speed consists of two separate assemblies. The first is the control unit which provides the hydraulic supply, speed governing and feather function for the system. The second unit is the hydro-mechanical pitch change actuator which directly changes blade angle (pitch) as scheduled by the control.

Schwartz, R. A.↗
NASA NTRS1985

SSME digital control design characteristics

To protect against a latent programming error (software fault) existing in an untried branch combination that would render the space shuttle out of control in a critical flight phase, the Backup Flight System (BFS) was chartered to provide a safety alternative. The BFS is designed to operate in critical flight phases (ascent and descent) by monitoring the activities of the space shuttle flight subsystems that are under control of the primary flight software (PFS) (e.g., navigation, crew interface, propulsion), then, upon manual command by the flightcrew, to assume control of the space shuttle and deliver it to a noncritical flight condition (safe orbit or touchdown). The problems associated with the selection of the PFS/BFS system architecture, the internal BFS architecture, the fault tolerant software mechanisms, and the long term BFS utility are discussed.

Mitchell, W. T.↗
NASA NTRS2009

L(sub 1) Adaptive Control Design for NASA AirSTAR Flight Test Vehicle

In this paper we present a new L(sub 1) adaptive control architecture that directly compensates for matched as well as unmatched system uncertainty. To evaluate the L(sub 1) adaptive controller, we take advantage of the flexible research environment with rapid prototyping and testing of control laws in the Airborne Subscale Transport Aircraft Research system at the NASA Langley Research Center. We apply the L(sub 1) adaptive control laws to the subscale turbine powered Generic Transport Model. The presented results are from a full nonlinear simulation of the Generic Transport Model and some preliminary pilot evaluations of the L(sub 1) adaptive control law.

Gregory, Irene M.↗
NASA NTRS1971

Space shuttle guidance, navigation and control design equations. Volume 3: Orbital operations

Revised specifications are presented of the equations necessary to perform the guidance, navigation, and control onboard computation functions for the space shuttle orbiter vehicle. The orbital operations covered include: (1) orbital coast, (2) orbital powered flight, (3) rendezvous mission phase, (4) station keeping mission phase, (5) docking and undocking, and (6) docked operations.

Source record↗
NASA NTRS2001

Adaptive Multi-Layer LMS Controller Design and Application to Active Vibration Suppression on a Truss and Proposed Impact Analysis Technique

This research develops an adaptive controller that actively suppresses a single frequency disturbance source at a remote position and tests the system on the NPS Space Truss. The experimental results are then compared to those predicted by an ANSYS finite element model. The NPS space truss is a 3.7-meter long truss that simulates a space-borne appendage with sensitive equipment mounted at its extremities. One of two installed piezoelectric actuators and an Adaptive Multi-Layer LMS control law were used to effectively eliminate an axial component of the vibrations induced by a linear proof mass actuator mounted at one end of the truss. Experimental and analytical results both demonstrate reductions to the level of system noise. Vibration reductions in excess of 50dB were obtained through experimentation and over 100dB using ANSYS, demonstrating the ability to model this system with a finite element model. This report also proposes a method to use distributed quartz accelerometers to evaluate the location, direction, and energy of impacts on the NPS space truss using the dSPACE data acquisition and processing system to capture the structural response and compare it to known reference Signals.

Barney, Timothy A.↗
NASA NTRS1990

Implementation of sensor and control designs for bioregenerative systems

The EGM 4000/4001 Engineering Design class is an interdisciplinary design course that allows students to experience the design process. The projects involved the design of sensors and subsystems of a closed-loop life support system (CLLSS) with special emphasis on the Controlled Ecological Life Support System (CELSS) currently being developed at Kennedy Space Center (KSC) by NASA. To understand the work performed by the students, one must understand the purpose and concept of a CLLSS system. In the years to come, NASA will be constructing Moon bases and sending astronauts to other worlds on extended space missions. In order to support the crews, unreasonably large quantities of supplies would have to be sent from Earth. These supplies would be difficult to transport and require large holds. To remedy this problem, NASA plans to incorporate crops into the spacecraft. These crops would supply food for the crews, as well as provide beneficial psychological side effects. In addition, the plants would recycle the air and human waste and provide oxygen and water for the humans. The students in the design class were to work on supporting this project. In order to do this successfully, the course was separated into two phases. The first semester involved studying the various aspects of a CLLSS to determine sensing needs and develop ideas. The second semester involved first determining which of the ideas were most promising. Specific sensors were then designed and tested under laboratory conditions with promising results. Finally, recommendations for further development were proposed. Atmosphere and temperature control, nutrient delivery, plant health and propagation, and resource recycling are discussed.

Source record↗
NASA NTRS1982

A temperature control design for a tapered element oscillating microbalance sensing surface

A design study is presented which shows that a tapered element oscillating microbalance can be adapted for temperature control under space application by mating with multistage thermoelectric coolers in such a way that an integral structure evolves. The control of the temperature of the sensing surface can be achieved in a number of ways. An indirect method which uses a measurement of the absorbed power is recommended. The design goals can be met if a relaxation of the power requirement can be considered.

Source record↗
NASA NTRS1971

Space shuttle guidance, navigation and control design equations. Volume 4: Deorbit and atmospheric operations

A baseline set of equations which fulfill the computation requirements for guidance, navigation, and control of the space shuttle orbiter vehicle is presented. All shuttle mission phases are covered from prelaunch through landing/rollout. The spacecraft flight mode and the aircraft flight mode are addressed. The baseline equations may be implemented in a single guidance, navigation, and control computer or may be distributed among several subsystem computers.

Cox, K. J.↗
NASA NTRS1986

The interpretation of flying qualities requirements for flight control design

The flying requirements of MIL-F-8785(C) are interpreted in terms of command/response configurations, and pilot preference for flight control systems configurations of angle of attack, or pitch rate command, specified independently for the short period and phugoid dynamics, is determined using the Total-In-Flight-Simulator aircraft. The results show that for either command configuration, the short term response applies to the angle of attack response of the vehicle, and that this response must satisfy the omega(n) vs n/alpha requirement. The preference in the long term for angle of attack command indicates that the pilot wants the aircraft to fly in the direction it is pointing, and an attitude hold system is not found to be preferred unless attitude hold results in flight path angle hold.

Rynaski, E. G.↗