Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “COMPONENT REPORTS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18

Static stability and control effectiveness of models 12-0 and 34-0 of the vehicle 3 configuration, volume 3

Static stability and control effectiveness characteristics of two 0.004 scale models of the vehicle 3 configuration are reported. The components investigated consisted of a single aft body, vertical/rudder, OMS pods with two interchangeable wings, four interchangeable forward bodies, four trimmers, and a spoiler. The test was conducted in 14 x 14 inch trisonic wind tunnel over a Mach number range from 0.6 to 4.96. Angles of attack from 0 to 60 degrees and angles of sideslip from -10 to 10 degrees at 0, 10, 20,30, and 40 degrees angle of attack were tested. Elevon, body flap, and speed brake deflection composed the parametric considerations. No grit was placed on the models during the test. The tabulated source data and incremental data figures are presented.

Allen, E. C.↗

MSFC Skylab Orbital Workshop, volume 3

The waste management system for the Skylab Orbital Workshop is discussed. The general requirements of the system are presented. Illustrations of the components of the system are provided. Data concerning maximum expected performance capabilities are developed. The results of performance tests on the system components are reported. Emphasis is placed on the human factors engineering aspects of the system.

Source record↗

Load distribution on a closed-coupled wing canard at transonic speeds

A wind tunnel test where load distributions were obtained at transonic speeds on both the canard and wing surfaces of a closely coupled wing canard configuration is reported. Detailed component and configuration arrangement studies to provide insight into the various aerodynamic interference effects for the leading edge vortex flow conditions encountered are included. Data indicate that increasing the Mach number from 0.70 to 0.95 caused the wing leading edge vortex to burst over the wing when the wing was in the presence of the high canard.

Gloss, B. B.↗

LMC X-1, X-2, and X-3 - Precise positions from the HEAO 1 modulation collimator

Precise (to about 20 arcsec) positions are reported for the Large Magellanic Cloud X-ray sources LMC X-1, X-2, and X-3, determined with the HEAO 1 scanning modulation collimator. The error regions for LMC X-1 and X-3 contain, respectively, the B5 supergiant R148 and a possibly variable B III-IV star. Spectra taken of the latter confirm the spectral type and show that it is a member of the LMC. A search for a previously reported extended component of LMC X-1 yields upper limits which exclude it.

Johnston, M. D.↗

Measuring software development characteristics in the local environment

In a brief evaluation of software-related considerations, it is found that suitable approaches for software development depend to a large degree on the characteristics of the particular project involved. An analysis is conducted of development problems in an environment in which ground support software is produced for spacecraft control. The amount of work involved is in the range from 6 to 10 man-years. Attention is given to a general project summary, a programmer/analyst survey, a component summary, a component status report, a resource summary, a change report, a computer program run analysis, aspects of data collection on a smaller scale, progress forecasting, problems of overhead, and error analysis.

Basili, V. R.↗

High temperature UF6 RF plasma experiments applicable to uranium plasma core reactors

An investigation was conducted using a 1.2 MW RF induction heater facility to aid in developing the technology necessary for designing a self critical fissioning uranium plasma core reactor. Pure, high temperature uranium hexafluoride (UF6) was injected into an argon fluid mechanically confined, steady state, RF heated plasma while employing different exhaust systems and diagnostic techniques to simulate and investigate some potential characteristics of uranium plasma core nuclear reactors. The development of techniques and equipment for fluid mechanical confinement of RF heated uranium plasmas with a high density of uranium vapor within the plasma, while simultaneously minimizing deposition of uranium and uranium compounds on the test chamber peripheral wall, endwall surfaces, and primary exhaust ducts, is discussed. The material tests and handling techniques suitable for use with high temperature, high pressure, gaseous UF6 are described and the development of complementary diagnostic instrumentation and measurement techniques to characterize the uranium plasma, effluent exhaust gases, and residue deposited on the test chamber and exhaust system components is reported.

Roman, W. C.↗

Evaluation of approximate methods for the prediction of noise shielding by airframe components

An evaluation of some approximate methods for the prediction of shielding of monochromatic sound and broadband noise by aircraft components is reported. Anechoic-chamber measurements of the shielding of a point source by various simple geometric shapes were made and the measured values compared with those calculated by the superposition of asymptotic closed-form solutions for the shielding by a semi-infinite plane barrier. The shields used in the measurements consisted of rectangular plates, a circular cylinder, and a rectangular plate attached to the cylinder to simulate a wing-body combination. The normalized frequency, defined as a product of the acoustic wave number and either the plate width or cylinder diameter, ranged from 4.6 to 114. Microphone traverses in front of the rectangular plates and cylinders generally showed a series of diffraction bands that matched those predicted by the approximate methods, except for differences in the magnitudes of the attenuation minima which can be attributed to experimental inaccuracies. The shielding of wing-body combinations was predicted by modifications of the approximations used for rectangular and cylindrical shielding. Although the approximations failed to predict diffraction patterns in certain regions, they did predict the average level of wing-body shielding with an average deviation of less than 3 dB.

Ahtye, W. F.↗

HG ion thruster component testing

Cathodes, isolators, and vaporizers are critical components in determining the performance and lifetime of mercury ion thrusters. The results of life tests of several of these components are reported. A 30-cm thruster CIV test in a bell jar has successfully accumulated over 26,000 hours. The cathode has undergone 65 restarts during the life test without requiring any appreciable increases in starting power. Recently, all restarts have been achieved with only the 44 volt keeper supply with no change required in the starting power. Another ongoing 30-cm Hg thruster cathode test has successfully passed the 10,000 hour mark. A solid-insert, 8-cm thruster cathode has accumulated over 4,000 hours of thruster operation. All starts have been achieved without the use of a high voltage ignitor. The results of this test indicate that the solid impregnated insert is a viable neutralizer cathode for the 8-cm thruster.

Mantenieks, M. A.↗

Aerodynamic/acoustic performance of YJ101/double bypass VCE with coannular plug nozzle

Results of a forward Variable Area Bypass Injector test and a Coannular Nozzle test performed on a YJ101 Double Bypass Variable Cycle Engine are reported. These components are intended for use on a Variable Cycle Engine. The forward Variable Area Bypass Injector test demonstrated the mode shifting capability between single and double bypass operation with less than predicted aerodynamic losses in the bypass duct. The acoustic nozzle test demonstrated that coannular noise suppression was between 4 and 6 PNdB in the aft quadrant. The YJ101 VCE equipped with the forward VABI and the coannular exhaust nozzle performed as predicted with exhaust system aerodynamic losses lower than predicted both in single and double bypass modes. Extensive acoustic data were collected including far field, near field, sound separation/ internal probe measurements as Laser Velocimeter traverses.

Vdoviak, J. W.↗

The interstellar medium on the Gamma Cassiopeiae line of sight

The interstellar medium on the Gamma Cas line of sight is studied through the observations of O I, H2, H I, D I, and Ar I absorption features with the Copernicus satellite. By using the velocity structure of the line of sight previously determined through atomic nitrogen, it is demonstrated that these neutrals are located in the same physical regions and that the O I and Ar I abundances could be solar, on the average, relative to N I in all components. The 1066.660 A Ar I line profile is contaminated by an unidentified line, already detected in the spectrum of Zeta Pup. Furthermore, a peculiar behavior of the Ar I abundance in the different components is reported, possibly associated with high-velocity interstellar gas present on the line of sight. It is concluded that the Gamma Cas line of sight could intercept a dense cloud which has been engulfed and disrupted by a shock.

Ferlet, R.↗

Development and demonstration of manufacturing processes for fabricating graphite/Larc-160 polyimide structural elements, part 4, paragraph C

Progress in the development of processes for production of Celion/LARC-160 graphite-polyimide materials, quality control methods, and the fabrication of Space Shuttle composite structure components is reported. The formulation and processing limits for three batches of resin are presented. Process improvements for simplification of the imidizing and autoclave cure cycles are described. Imidized and autoclave cured test panels were prepared. Celion/LARC-160 cure process verification and the fabrication of honeycomb sandwich panel elements and skin/stringer panels are described. C-scans of laminates imidized at 163 C to 218 C for periods from 30 to 180 minutes, and of process verification laminates made from different batches of prepreg are presented. Failure modes and load/strain characteristics of sandwich elements and C-scans of stringer to skin bond joints are also given.

Source record↗

Development and demonstration of manufacturing processes for fabricating graphite/Larc-160 polyimide structural elements, part 4, paragraph B

Progress in the development of processes for production of Celion/LARC-160 graphite-polyimide materials, quality control, and the fabrication of Space Shuttle composite structure components is reported. Liquid chromatographic analyses of three repeatibility batches were performed and are compared to previous Hexcel standard production and to variables study LARC-160 intermediate resins. Development of processes for chopped fiber molding are described and flexural strength, elastic modulus, and other physical and mechanical properties of the molding are presented.

Source record↗

Characteristics of inhomogeneous jets in confined swirling air flows

An experimental program to study the characteristics of inhomogeneous jets in confined swirling flows to obtain detailed and accurate data for the evaluation and improvement of turbulent transport modeling for combustor flows is discussed. The work was also motivated by the need to investigate and quantify the influence of confinement and swirl on the characteristics of inhomogeneous jets. The flow facility was constructed in a simple way which allows easy interchange of different swirlers and the freedom to vary the jet Reynolds number. The velocity measurements were taken with a one color, one component DISA Model 55L laser-Doppler anemometer employing the forward scatter mode. Standard statistical methods are used to evaluate the various moments of the signals to give the flow characteristics. The present work was directed at the understanding of the velocity field. Therefore, only velocity and turbulence data of the axial and circumferential components are reported for inhomogeneous jets in confined swirling air flows.

So, R. M. C.↗

Solar noise storms - The polarization of storm Type III and related bursts

The spectral and polarization characteristics of 19 noise storms that occurred during 1976-1982 are reported. All components of the storms - Type I bursts and continuum, storm Type III bursts, and fine structures such as reverse drift pairs - are found to have the same sense of circular polarization. While the degree of polarization p of Type I bursts and continuum is generally greater than or approximately equal to 0.5, that of storm Type III bursts is almost always less than 0.5. Two set of storm Type III bursts stand out: one with less than or approximately equal to 0.2 and another with greater than or approximately equal to 0.3. Because these sets respectively have degrees of polarization so similar to those of fundamental (F) the harmonic (H) components of non-storm F - H pairs, it is deduced that storm Type III bursts are due sometimes to fundamental plasma radiation and sometimes to harmonic. However, F - H pairs are extremely rare among storm Type III bursts.

Dulk, G. A.↗

Dynamic response and acoustic fatigue of stiffened composite structure

The results of acoustic fatigue and dynamic response tests performed on L-1011 graphite-epoxy (GrE) aileron and panel components are reported. The aileron featured glass microballoons between the GrE skins. Tests yielded random fatigue data from double and single cantilever coupons and modal data from impedance hammer and loudspeaker impulses. Numerical and sample test data were obtained on combined acoustic and shear loads, acoustic and thermal loads, random fatigue and damping of the integrally stiffened and secondary bonded panels. The fatigue data indicate a fatigue life beyond 10 million cycles. The acoustic data suggested that noise transmission could be enhanced in the integrally stiffened panels, which were more acoustic-fatigue resistant than were the secondary bonded panels.

Soovere, J.↗