Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “CALCULATION METHODS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18
All sourcesNASA NTRSDOE OSTI
NASA NTRS1973

An inexpensive and effective method for calculating the strength of randomly reinforced fiber composites

Planar randomly reinforced fiber composites (PRRFC) is pseudoisotropic laminate with large number of ply orientation combinations where strength is function of these ply orientation combinations. Laminate theory can be applied to determine strength of PRRFC, and in conjunction with composite micro- and macromechanics can predict mechanical properties of PRRFC's with any fiber/matrix combination.

Chamis, C. C.↗
NASA NTRS1972

A method for calculating transient thrust and flow-rate levels for Mariner type attitude control nitrogen gas jets

The purpose of this report is to define and program the transient pneumatic flow equations necessary to determine, for a given set of conditions (geometry, pressures, temperatures, valve on time, etc.), the total nitrogen impulse and mass flow per pulse for the single pulsing of a Mariner type reaction control assembly valve. The rates of opening and closing of the valves are modeled, and electrical pulse durations from 20 to 100 ms are investigated. In developing the transient flow analysis, maximum use was made of the steady-state analysis. The impulse results are also compared to an equivalent square-wave impulse for both the Mariner Mars 1971 (MM'71) and Mariner Mars 1964 (MM'64) systems. It is demonstrated that, whereas in the MM'64 system, the actual impulse was as much as 56 percent higher than an assumed impulse (which is the product of the steady-state thrust and value on time i.e., the square wave), in the MM'71 system, these two values were in error in the same direction by only approximately 4 percent because of the larger nozzle areas and shorter valve stroke used.

Ferrera, J. D.↗
NASA NTRS1973

A method for calculating unsteady turbulent boundary layers in two- and three-dimensional flows.

The governing equations for an unsteady turbulent boundary layer on a swept infinite cylinder, composed of a continuity equation, a pair of momentum equations and a pair of rate equations for the shear stress, based on the turbulent kinetic-energy equation, are solved numerically. These rate equations for the shear-stress express a balance between the convection, production, dissipation and diffusion of the turbulent shear stress components. Due to the physical model of turbulence employed, this system of equations is hyperbolic. An explicit, second-order accurate, conditionally stable difference scheme for this system, together with appropriate boundary and initial conditions, is formulated and developed into a computer program. Calculations for oscillating free stream flows with no pressure gradient show significant unsteady effects on the turbulent boundary layer.

Singleton, R. E.↗
NASA NTRS1975

Rapid methods for calculating radiation transport in the entry environment

A procedure is developed for the prediction of radiation transport events in the context of the entry heating environment. The equivalent-width and exponential approximations are employed to reduce the computational requirements of the governing equations. Novel features are introduced in the use of an Elsasser band model to estimate line overlapping events and in the formulation of the wall reflection events. A matrix of calculations is presented to allow an assessment of the trade-offs between accuracy and computational efforts. It is concluded that the equivalent width model allows significant savings in computational effort with only modest penalties in accuracy. Consequently, the model should be viewed as an attractive candidate for use in radiation-coupled flow field prediction procedures.

Nicolet, W. E.↗
NASA NTRS1975

Approximate method for calculating transonic flow about lifting wing-body configurations: Computer program and user's manual

A user's manual is presented for a computer program which calculates inviscid flow about lifting configurations in the free-stream Mach-number range from zero to low supersonic. Angles of attack of the order of the configuration thickness-length ratio and less can be calculated. An approximate formulation was used which accounts for shock waves, leading-edge separation and wind-tunnel wall effects.

Barnwell, R. W.↗
NASA NTRS1978

Methods for calculating the transonic boundary layer separation for V/STOL inlets at high incidence angles

A semi-empirical scheme for the prediction of transonic pressure distribution on the surface of V/STOL inlets at high incidence angles has been developed. The investigation is intended to improve the boundary layer calculation and separation prediction by including the effects of shock wave-boundary layer interaction into the Lewis Inlet Viscous Computer Program. Wind-tunnel results and theoretical pressure calculation for critical cases are used in constructing the transonic pressure distribution. The program, which describes the development of the boundary layer and predicts the possible flow separation, can handle the cases of inlets at high incidence angles where local supersonic region may occur in the flow.

Chou, D. C.↗
NASA NTRS1983

Theoretical method for calculating relative joint geometry of assembled robot arms

Equations are developed to extract the relative joint parameters of an assembled robot arm. Specifically, the Denavit-Hartenberg parameters, which completely characterize the relative joint geometry, are calculated. These parameters are needed to control the hand of the robot arm by resolved rate. As an example, the parameter extraction equations are used with perfect simulated data (no measurement noise) obtained from a mathematical model of a six-degree-of-freedom robot arm. For an actual application, measurement data needed to estimate the relative joint parameters can be generated by moving a robot arm to different positions, measuring the location of the hand (or other extension) in base coordinates, and recording the corresponding joint angles.

Barker, L. K.↗
NASA NTRS1983

Method for calculating effects of a propfan on aircraft aerodynamics at subsonic speeds

A subsonic-flow panel code has been modified to handle the effects of a propeller wake. The effects of the propeller were modelled by a system of ring vortices of constant strength. Principles based on the blade element theory and the momentum theory were used to evaluate the swirl velocity and the pressure increase, across the propeller. Theoretical calculations are compared to experimental results at a Mach number of 0.50. The discrepancies between the theory and the experimental results are analysed. Suggestions for improvements to enhance the accuracy of the theoretical prediction are indicated.

Chandrasekaran, B.↗
NASA NTRS1984

A comparison of several methods of calculating fracture toughness from composite laminate test data

Critical fracture toughness was determined by two different techniques for graphite/epoxy laminates of three stacking sequences and several thicknesses. Critical fracture toughness was determined by a finite element stress analysis of a center-cracked tension specimen which yielded the stress intensity factor as a function of specimen thickness and applied load. As an alternative approach the critical strain energy release rate was determined from the compliance calibration technique. Test results from both procedures are compared and discussed.

Harris, C. E.↗
NASA NTRS1987

Improving the method of calculating electronic properties of narrow bandgap semiconductors

A previously developed code for calculating the mobility of charge carriers in narrow bandgap semiconductors does not predict the correct temperature dependence in all cases. It is thought that this is due to the way the electronic screening of the carriers is treated in the model. The objective of this research is to improve the handling of the screening by going beyond the current first Born approximation. Much of this work is directly related to the alloy semiconductor Hg sub 1-xCd sub xTe which is important for infrared detectors and is a good candidate for microgravity crystal growth. The principal conclusion, so far, is that the major difficulty is probably the treatment of short range screening at higher temperatures.

Patterson, James D.↗