Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “CALCINATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18

NITRATE DESTRUCTION LITERATURE SURVEY AND EVALUATION CRITERIA

This report satisfies the initial phase of Task WP-2.3.4 Alternative Sodium Recovery Technology, Subtask 1; Develop Near-Tank Nitrate/Nitrite Destruction Technology. Some of the more common anions in carbon steel waste tanks at SRS and Hanford Site are nitrate which is corrosive, and nitrite and hydroxide which are corrosion inhibitors. At present it is necessary to periodically add large quantities of 50 wt% caustic to waste tanks. There are three primary reasons for this addition. First, when the contents of salt tanks are dissolved, sodium hydroxide preferentially dissolves and is removed. During the dissolution process the concentration of free hydroxide in the tank liquid can decrease from 9 M to less than 0.2 M. As a result, roughly half way through the dissolution process large quantities of sodium hydroxide must be added to the tank to comply with requirements for corrosion control. Second, hydroxide is continuously consumed by reaction with carbon dioxide which occurs naturally in purge air used to prevent buildup of hydrogen gas inside the tanks. The hydrogen is generated by radiolysis of water. Third, increasing the concentration of hydroxide increases solubility of some aluminum compounds, which is desirable in processing waste. A process that converts nitrate and nitrite to hydroxide would reduce certain costs. (1) Less caustic would be purchased. (2) Some of the aluminum solid compounds in the waste tanks would become more soluble so less mass of solids would be sent to High Level Vitrification and therefore it would be not be necessary to make as much expensive high level vitrified product. (3) Less mass of sodium would be fed to Saltstone at SRS or Low Level Vitrification at Hanford Site so it would not be necessary to make as much low level product. (4) At SRS less nitrite and nitrate would be sent to Defense Waste Processing Facility (DWPF) so less formic acid would be consumed there and less hydrogen gas would be generated. This task involves literature survey of technologies to perform the nitrate to hydroxide conversion, selection of the most promising technologies, preparation of a flowsheet and design of a system. The most promising technologies are electrochemical reduction of nitrates and chemical reduction with hydrogen or ammonia. The primary reviewed technologies are listed and they aredescribed in more detail later in the report: (1) Electrochemical destruction; (2) Chemical reduction with agents such as ammonia, hydrazine or hydrogen; (3) Hydrothermal reduction process; and (4) Calcination. Only three of the technologies on the list have been demonstrated to generate usable amounts of caustic; electrochemical reduction and chemical reduction with ammonia, hydrazine or hydrogen and hydrothermal reduction. Chemical reduction with an organic reactant such as formic acid generates carbon dioxide which reacts with caustic and is thus counterproductive. Treatment of nitrate with aluminum or other active metals generates a solid product. High temperature calcination has the potential to generate sodium oxide which may be hydrated to sodium hydroxide, but this is unproven. The following criteria were developed to evaluate the most suitable option. The numbers in brackets after the criteria are relative weighting factors to account for importance: (1) Personnel exposure to radiation for installation, routine operation and maintenance; (2) Non-radioactive safety issues; (3) Whether the technology generates caustic and how many moles of caustic are generated per mole of nitrate plus nitrite decomposed; (4) Whether the technology can handle nitrate and nitrite at the concentrations encountered in waste; (5) Maturity of technology; (6) Estimated annual cost of operation (labor, depreciation, materials, utilities); (7) Capital cost; (8) Selectivity to nitrogen as decomposition product (other products are flammable and/or toxic); (9) Impact of introduced species; (10) Selectivity for destruction of nitrate vs. nitrite; and (11) Cost of deactivation and demolition. Each technology was given a score from one to five, five being most desirable, in each criterion. The results for the evaluation, in order from most to least promising was, Electrochemical, Chemical Reduction, Hydrothermal and Calcining. Another report [Steimke and Steeper, 2011] contains a flowsheet and design of an in-tank Electrochemical unit.

08 HYDROGEN↗

LANL Response to SRS Requirement G-ESR-G-00035 Item 11 Bed Temperature, Revision 4

Los Alamos National Laboratory has identified a number of plutonium-bearing materials that will be placed in interim storage in 3013 containers per requirements of DOE-STD-3013- 2004, or DOE-STD-3013-2012. Before these items can be considered for storage at Savannah River Site, 20 points of agreement, described in Savannah River Site (SRS) document G-ESR-G-00035, Revision 1, must be documented and provided to SRS for review. These agreements include documentation that the requirements of the 3013 Standard are met and the storage facility’s safety envelope is not compromised. Point 11 of the 20 points is the requirement that material be stabilized at 950°C for a minimum of two hours prior to packaging. This report addresses the Point 11 requirement, describing the controls used during stabilization to ensure that the material is properly stabilized using either a batch (calciner boat) or continuous process (Advanced Recovery and Integrated Extraction System [ARIES] direct metal oxidation unit 2 [DMO-2] and recycle oxide calcination). These controls include verification of the furnace controller thermocouple profile and verification of the profiles for the two thermocouples located in the bed and/or calciner tube hot zone. Revision 4 to this document only modifies the ARIES DMO-2 process controls. Batch processing requirements are unchanged. Changes to the DMO-2 process include use of alternate augers with differing pitch values and reduction of the minimum powder bulk density value. The new DMO-3 unit requirements are covered in a separate document.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

MIS High-Purity Plutonium/Uranium Oxide Hydride Product 5501407 (SSR129): Final Report

A high-purity uranium/plutonium mixed oxide material from the Material Identification and Surveillance (MIS) Program inventory has been studied with regard to gas generation and corrosion in a storage environment. Sample 5501579 represents process plutonium oxides from high purity mixed oxides and mixed oxides from alloy oxidation at Hanford, hydride oxide from Rocky Flats, and mixed oxides from alloy oxidation and scrap mixed oxides at Savannah River that are currently stored in 3013 containers. This study followed over time the gas pressure of two samples of this material with nominally 0.5 wt% water in a sealed container with an internal volume scaled to 1/500th of the volume of a 3013 container. The first experiment studied a mixture of 60% as-received material (AR) and 40% material that had been calcined at 950 °C. The mixture contained 66% weapons grade plutonium and 11% uranium, with approximately 7.3% impurities and the remainder principally oxygen. A second experiment studied material calcined at 950 °C which contained approximately 4.3% impurities and similar uranium and plutonium content. Gas compositions were measured periodically over approximately 3.5 years in the first container and 20 months for the second container, which was terminated early due to an inadvertent container pumpdown. The maximum observed gas pressures were 152 kPa and 161 kPa, respectively. The increase over the initial pressures of 82 kPa and 88 kPa, respectively, was primarily due to generation of carbon dioxide and nitrogen gases. In the container with the AR/calcined mixture, a small amount of hydrogen and oxygen was generated and was consumed. In the container with calcined material only, hydrogen partial pressure of 18.9 kPa was measured. A small amount of oxygen was generated and was consumed. At the completion of the study, the internal components of both sealed containers showed signs of corrosion

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Mark-18A Cold Runs

The Savannah River National Laboratory (SRNL) is tasked by the National Nuclear Security Administration (NNSA) to recover highly valued isotopes from irradiated Mark-18A (Mk-18A) targets. The Savannah River Site (SRS) has sixty-five Mk-18A targets available for the recovery of the high valued materials. The sixty-five Mk-18A targets are currently stored in the L-Area Basin and will be removed one at a time and individually transported to SRNL. Upon receipt at SRNL, the Mk-18A target material will be removed from the confinement, dissolved, chemically separated, and calcined to a stable oxide. The flowsheet is designed to recover the plutonium as well as the trivalent actinides. The remaining unrecovered material will be discarded to the high activity drain (HAD) system in SRNL. A specially designed cask was procured for transport of the targets from L-Area to SRNL. Once received at SRNL, the targets will be loaded into the back of Cell 7 and resized as they enter the cell. The resized targets (1/4 lengths) will then be processed one at a time through the following processes: caustic dissolution and filtration; acidic dissolution and filtration, Reillex anion exchange, diglycolamide (DGA) cation exchange; and DGA calcination. This processing will result in two product streams. The first is an aqueous plutonium solution which will be removed from the shielded cells and taken to a glovebox for further purification and conversion to an oxide. The second is a calcined oxide containing the Am and Cm as well as other lanthanide fission products which will be removed from the shielded cells using a bagless transfer system. Both materials will be packaged for shipment to Oak Ridge National Laboratory (ORNL). All equipment to carry out this process was designed, procured or fabricated, and installed in a mock-up facility (716-4A) at SRS to allow for simulation testing in a non-radioactive area. This equipment was then dismantled and transferred from 716-4A to 773-A and installed in the SRNL Shielded Cells. After installation in the shielded cells facility testing was performed using water followed by surrogates and cold chemicals. Issues were identified during these evaluations, including equipment issues as well as technical challenges. Many of the issues were rectified during performance of the cold runs, and the remaining have a resolution identified. Table ES-1 provides a summary of all issues identified during the cold run operations, as well as the status and identified resolutions to outstanding issues.

07 ISOTOPE AND RADIATION SOURCES↗

Development of Manganese and Iron Mixed Metal Oxides for Thermochemical Energy Storage

Energy storage plays an essential role for sustainable and renewable energy use in an effort to reduce carbon emissions. Thermochemical energy storage (TCES) is a favorable alternative to fossil fuel energy systems and a promising solution to the intermittency problem of renewable energy sources (such as solar energy). TCES stores energy in the form of chemical bonds using reversible redox reactions (such as manganese metal oxides). This study developed manganese oxide (Mn2O3) and iron oxide (Fe2O3) with an inert dispersant of silicon dioxide (SiO2) (Mn-Fe-Si) for potential large scale energy storage application. These metal oxides are nontoxic, cheap, and relatively abundant. The materials were prepared with varying metal oxide content using physical mixing in a ball mill, pressure pelletization and calcination at different temperatures. Redox cycle tests were conducted using differential scanning calorimetry combined with thermogravimetric analysis (TGA-DSC). The Mn-Fe-Si materials had higher cyclability and energy release compared to the pure metal oxides and manganese oxide with SiO2. The calcination temperature had a significant effect on releasable energy due to the interactions between the oxides. The Mn-Fe-Si mixture calcined at high temperature (1000oC) showed the highest average energy storage density.

Wilkinson, Olivia↗

Development of high T(sub c) (greater than 110 K) Bi, Tl, and Y-based materials as superconducting circuit elements

Experimental work has continued on the development and characterization of bulk and hot pressed powders and tapecast materials in the Bi-Sr-Ca-Cu-O and Tl-Ba-Ca-Cu-O systems. A process for producing warp-free, sintered, superconducting tapes of Bi composition Bi2Sr2Ca2Cu3O(x) with a mixed oxide process was established. This procedure required a triple calcination at 830 C for 24 hours and sintering at 845 C from 20 to 200 hours. Hot pressing the triple calcined powder at 845 C for 6 hours at 5000 psi yielded a dense material which on further heat treatment at 845 C for 24 hours exhibited a Tc of 108.2 K. A further improvement in the processing of the bismuth materials was achieved via a chemical coprecipitation process wherein the starting nitrate materials were coprecipitated with oxalic acid, thus yielding a more chemically homogeneous, more reactive powder. With the coprecipitated powders, only one calcine at 830 C for 12 hours and a final sinter at 845 C for 30 hours was sufficient to produce a bulk superconducting material with a Tc of 108.4 K. SAFIRE-type grounding links were successfully fabricated from sintered, tapecast, coprecipitated BSCCO 2223 powders. Compositional and processing investigations were continued on the Tl-based superconductors. Manganese and lithium additions and sintering temperature and time were examined to determine their influence on superconducting properties. It was found that lithium substitutions for copper enhance the transition temperatures while manganese additions produced deleterious effects on the superconducting properties. A suitable procedure for producing reproducible bulk and tapecast material of Tl composition Tl2Ba2Ca2Cu3O(x) was developed and used in fabricating uniform superconducting tapes. The highest transition temperature for Tl-based tapes was measured at 110.2 K. Thallium superconducting SAFIRE-type grounding links were fabricated from the tapes.

Haertling, Gene H.↗

Sol-Gel Synthesis of La(0.6)Sr(0.4)CoO(3-x) and Sm(0.5)Sr(0.5)CoO(3-x) Cathode Nanopowders for Solid Oxide Fuel Cells

Nanopowders of La(0.6)Sr(0.4)CoO(3-x) (LSC) and Sm(0.5)Sr(0.5)CoO(3-x) (SSC) compositions, which are being investigated as cathode materials for intermediate temperature solid oxide fuel cells (IT-SOFC) with La(Sr)Ga(Mg)O(3-x) (LSGM) as the electrolyte, were synthesized by low-temperature sol-gel method using metal nitrates and citric acid. Thermal decomposition of the citrate gels was followed by simultaneous DSC/TGA methods. Development of phases in the gels, on heat treatments at various temperatures, was monitored by x-ray diffraction. Solgel powders calcined at 550 to 1000 C consisted of a number of phases. Single perovskite phase La(0.6)Sr(0.4)CoO(3-x) or Sm(0.5)Sr(0.5)CoO(3-x) powders were obtained at 1200 and 1300 C, respectively. Morphological analysis of the powders calcined at various temperatures was done by scanning electron microscopy. The average particle size of the powders was approx.15 nm after 700 C calcinations and slowly increased to 70 to 100 nm after heat treatments at 1300 to 1400 C.

Bansal, Narottam P.↗

High conductivity NASICON electrolyte for room temperature solid-state sodium ion batteries

Solid electrolytes compositions, methods of making the solid electrolytes, and methods of using the solid electrolytes in batteries and other electrochemical technologies are disclosed. The method of producing a solid electrolyte comprises (a) ball milling Na2CO3, SiO2, NH4H2PO4, a zirconium source, and a dopant to produce a ball milled powder; (b) calcining the ball milled powder to produce a calcined powder; and (c) sintering the calcined powder to produce a solid electrolyte. The zirconium source for the solid electrolyte may be ZrO2. The dopant for the solid electrolyte may be AI2O3, Fe2O3, Sb2O3, Yb2O3, or Dy2O3.

25 ENERGY STORAGE↗

Process for preparing doped lithium lanthanum zirconium oxide

A process for preparing doped-lithium lanthanum zirconium oxide (doped-LLZO) is described herein. The method involves dry doping of a co-precipitated lanthanum zirconium oxide (LZO) precursor. Dry doping is a process in which a dry powdered dopant is ground and mixed with a pre-prepared co-precipitated LZO precursor and a lithium salt to provide a LLZO precursor composition, which is subsequently calcined to form a doped-LLZO. The process described herein comprises calcining a dry, powdered (e.g., micron, sub-micron or nano-powdered) mixture of a co-precipitated LZO precursor, a dopant salt or oxide, and a lithium salt under an oxygen-containing atmosphere at a temperature in the range of about 500 to about 1100° C., and recovering the doped-LLZO after calcining.

Durham, Jessica L.↗

Use of Layered Double Hydroxide (LDH) Sorbents to Remove Radioactive Iodine Species - 17178

To more efficiently manage the radioactive iodine waste, layered double hydroxides (LDHs) were synthesized and characterized using XRD, FT-IR, SEM-EDS, and ICP-AES. Batch adsorption experiments to remove I{sup -} and IO{sub 3}{sup -} under DIW condition were conducted to check overall removal efficiencies with and without calcination using ICP-MS. Synthesized MgFe-Cl-C-21 LDHs consisting of Mg{sup 2+} and Fe{sup 3+} in a 2:1 concentration ratio of the divalent ion to the trivalent ion after calcination showed the highest I- removal efficiency, 89.2 % and synthesized CoCr-Cl-NC-41 LDHs consisting of Co{sup 2+} and Cr{sup 3+} in a 4:1 concentration ratio of the divalent ion to the trivalent ion without calcination showed the highest IO{sub 3}- removal efficiency, 97.0 %. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Mark-18A Target Material Recovery Program: Initial Hot Startup

The Savannah River National Laboratory (SRNL) has been tasked by the National Nuclear Security Administration to recover highly valued isotopes from irradiated Mark-18A (Mk-18A) targets. The Savannah River Site (SRS) has sixty-five Mk-18A targets available for the recovery of the high valued materials. The Mk-18A targets were manufactured with Pu-242 then irradiated under high neutron flux in K-Reactor at the SRS from 1968 to 1978. The sixty-five Mk-18A targets are currently stored in the SRS L-Area Basin and will be removed one at a time and individually transported to SRNL. Upon receipt at SRNL, the Mk-18A target material will be removed from the confinement, dissolved, chemically separated, and calcined to a stable oxide. The flowsheet is designed to recover the plutonium as well as the trivalent actinides. The original targets were manufactured with varying quantities of Pu-242, ranging from 5.2 grams to 121.5 grams. Taking a graded approach to process start up, the lowest loaded target (FT-80-03) was selected as the first target to be received and processed at SRNL. As operational experience and knowledge is gained from processing targets, higher loaded targets will be selected for processing to increase the quantities of valuable isotopes recovered. Due to dose concerns, the receipt and processing of the Mk-18A targets is performed in the SRNL Shielded Cells Facility. The targets are stored in a double J-can confinement in the L-Area Basin. A specially designed cask was procured for transport of the targets from L-Area to SRNL. Once received at SRNL, the targets are loaded into the back of Cell 7 and resized as they enter the cell. The resized targets (1/4 length) are then processed one at a time through the following processes: caustic dissolution and filtration, acidic dissolution and filtration, elutable Reillex anion exchange, diglycolamide (DGA) resin extraction, and DGA calcination. This processing results in two product streams. The first is an aqueous plutonium solution which is removed from the shielded cells and taken to a glovebox for further purification and conversion to an oxide. The second is a calcined oxide product containing the Am and Cm as well as other lanthanide fission products which is removed from the shielded cells using a bagless transfer system. Both materials are packaged for shipment to Oak Ridge National Laboratory (ORNL). This paper will discuss the operating experience, lessons learned, and results from initial process hot startup.

Armstrong, Christopher [Savannah River National La↗

Synthesis, characterization and application of sol-gel derived mesoporous TiO{sub 2} nanoparticles for dye-sensitized solar cells

Nanocrystalline mesoporous titania of anatase crystal phase were prepared by sol-gel route by varying calcination (400 C and 600 C) conditions, and the photo-electrochemical properties were investigated for dye-sensitized solar cell applications. The TTIP precursor in n-heptane solvent with ratio of water to TTIP (5:1) was found to be effective substrate for the working electrodes. The overall conversion efficiency of 7.59% was achieved under 1 sun irradiation with open circuit voltage of 0.77 V, current density of 17.00 mA/cm{sup 2} and FF of 51.12. The high efficiency of the 400 C calcined sample were attributed to its mesopores, high BET surface area (80.1 m{sup 2}/g) and large pore volume of prepared titania substrate which provide better surface for the absorption of dye, improves light harvesting efficiency and better charge injection. The prepared samples were characterized by XRD, small angle XRD, FE-SEM, TEM, IPCE, I-V curve, BET surface area and BJH plot techniques. (author)

14 SOLAR ENERGY↗

Controlled release of losartan from acid- and heat-treated halloysite nanotubes

In this work, a simple method was used to sustained release of losartan (LOS) as a high blood pressure-controller drug using halloysites (HNT) as a carrier. The present work can be considered as an effective method because of using HNT as a natural source, which is available, inexpensive, safe with specific structure that led to release of drug, gradually. This carrier was improved by calcination and etching processes and their effect was investigated on loading amount and in vitro release of drug from HNT. The products were characterized by various analyses such as: BET (Brunauer–Emmett–Teller), TG (thermal gravimetry), TEM (transmission electron microscopy), and XRD (X-ray powder diffraction). According to the studies, two processes improving had no effect on structure and morphology of HNT and only increased the lumen size of them. It should be noted, removal water molecules through calcination had binary effect on halloysites: enlargement of lumen and decreasing the drug loading. Besides, release rate was investigated and it showed that maximum and minimum release rate of LOS are assigned to simple HNT and etched-HNT (EHNT), respectively. Kinetics studies confirmed that releasing the LOS molecules from HNT followed by diffusion process that is identified as Fickian diffusion.

60 APPLIED LIFE SCIENCES↗

Particle Size-Dependent Zero-Field Exchange Bias in LaFeO {sub 3} Nanoparticles

The present communication deals with particle size-dependent zero-field cooled exchange effect in LaFeO{sub 3} (LFO). LFO nanoparticles were prepared by PVA-based sol-gel method. The sample was calcined at different temperatures (700, 750, and 800 {sup ∘}C) to tune the average particle size. The detailed crystal structural and their geometrical parameters were examined by means of Rietveld refinement using x-ray diffraction data. The different techniques such as Scherrer’s method, Williamson Hall method, FESEM, and TEM were applied to accurately determine the average particle size. Zero-field cooled exchange bias and weak ferromagnetism in antiferromagnetic nanoparticles was observed for all samples using hysteresis loop measurement. The training effect was studied to confirm that the loop shift originates due to exchange bias. Exchange bias as well as coercivity are strongly related to the particle size at low and room temperature. The results clearly demonstrate that the process of calcination tailor the overall properties of material which makes it a promising candidate for device applications.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Influence of Temperature on Sr{sub 0.35}La{sub 0.40}Ca{sub .25}Fe{sub 11.6}Co{sub 0.4}O{sub 19} Hexagonal Ferrites Against Structural, Morphological and Magnetic Properties Prepared by Conventional Ceramic Reaction Methodology

Conventional Ceramic Reaction Methodology has been utilized for the preparation of M-type hexagonal ferrites of Sr{sub 0.35}La{sub 0.40}Ca{sub 0.25}Fe{sub 11.6}Co{sub 0.4}O{sub 19} magnets. X-ray diffraction has been performed for phase determination of the magnetic powders. At calcination temperatures ranging from 1220 to 1330 {sup ∘}C, the synchronize compost of the magnetic powders comprised of M-type hexagonal ferrites together with a small amount of impurity phase such as α-Fe{sub 2}O{sub 3} were co-existed. At calcination temperature above 1270 {sup ∘}C, single-phase M-type hexaferrites can be obtained. The particles seemed to be in a hexagonal plate-like mould which spread-out homogeneously were examined by field emission scanning electron microscopy. The magnetic edibility of the magnetic powders was intended by permanent magnetic measurement test equipment vibrating sample magnetometer. Magnetic properties, such as specific saturation magnetization, coercivity and remanence were temperature-dependent. However, with the increase of sintering temperature, i.e. above 1270 {sup ∘}C, saturation magnetization was increased while the coercivity showed reversed order.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Facile Synthesis of Spinel Ferrites with Enhanced Magnetic Properties from Two Intractable Metallurgical Resources: Zinc-Bearing Dust and Nickel Laterite Ore

Nickel laterite ore and zinc-bearing dust are multi-metal-associated and intractable resources. Comprehensive and cooperative utilization of zinc-bearing dust and nickel laterite ore for the preparation of spinel ferrites with enhanced magnetic properties by a facile process was proposed. The structure and magnetic properties of as-prepared spinel ferrites were characterized by X-ray diffraction (XRD), Raman spectroscopy, and Physical Property Measurement System (PPMS). The effect of mass ratios of zinc-bearing dust to nickel laterite ore, calcination temperature, and Zn substitution content on the as-prepared samples was investigated in detail. A single phase of Zn-substituted spinel ferrites (x= 0.00, 0.10, 0.20, and 0.30) could be obtained when the mass ratios were controlled at 1:0.4, 1:4:1.8, 1:2:1.5, and 1:1:1.2 after being calcined at 900 {sup ∘}C for 30 min, respectively. The magnetic property tests present that the as-prepared spinel ferrite exhibits enhanced magnetic properties with the saturation magnetization (Ms) value of 66.8 emu g{sup − 1} and the coercivity (Hc) value of 26 Oe when the mass ratio was controlled at 1:1:1.2. This research could provide an effective way to transfer two intractable resources into soft magnetic materials.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Effect of Metal Substitution on the Magnetic Properties of Spinel Ferrites Synthesized from Zinc-Bearing Dust

This paper provides a facile way for comprehensive utilization of multi-metal-associated and intractable zinc-bearing dust to synthesize multi-metal-doped spinel ferrites. The effects of preparation conditions including mass ratios of zinc-bearing dust to MgO addition and calcination temperature on the purity of as-prepared samples were investigated in detail, as well as the effect of metal substitution on the magnetic properties of as-synthesized spinel ferrites. The results show that single-phase spinel ferrite could be obtained when the mixture with the mass ratio of zinc-bearing dust to MgO addition of 1:0.20 was calcined at 1000 {sup ∘}C for 2 h. The saturation magnetization M{sub s} values for Mg-substituted, Ni-substituted, and Mn-substituted ferrites are 43.2, 47.6, and 54.3 emu g{sup − 1}, respectively, which can be explained by Neel’s two sub-lattice collinear models and the cation distribution between the tetrahedron (A) sites and octahedral (B) sites of the as-prepared samples. Notably, the heavy metals leaching from the as-prepared samples are very limited compared with zinc-bearing dust. In this way, hazardous zinc-bearing dust could be comprehensively utilized to synthesize spinel ferrites with excellent magnetic properties.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗