Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Band gap”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18
All sourcesNASA NTRSDOE OSTI
NASA NTRS2000

Optical Characterization of Bulk ZnSeTe Solid Solutions

Optical characterization was performed on wafers sliced from crystals of ZnSe, ZnTe, and ZnSe(1-x)Te(x)(0 less than x less than 0.4) grown by physical vapor transport. Energy band gaps at room temperature were determined from optical transmission measurements on 11 wafers. A best fit curve to the band gap versus composition x data gives a bowing parameter of 1.45. This number lies between the value of 1.23 determined previously on ZnSeTe bulk crystals and the value of 1.621 reported on ZnSeTe epilayers. Low-temperature photoluminescence (PL) spectra were measured on six samples. The spectra of ZnSe and ZnTe were dominated by near band edge emissions and no deep donor-acceptor pairs were observed. The PL spectrum exhibited a broad emission for each of the ZnSe(1-x)Te(x) samples, 0.09 less than x less than 0.39. For x=0.09, this emission energy is about 0.2 eV lower than the band gap energy measured at low temperature. As x increases the energy discrepancy gradually decreases and reduces to almost zero at x=0.4. The single broad PL emission spectra and the spectra measured as a function of temperature were interpreted as being associated with the exciton bound to Te clusters because of the high Te content in these samples.

Su, Ching-Hua↗
DOE OSTI2022

High throughput discovery of enhanced visible photoactivity in Fe–Cr vanadate solar fuels photoanodes

Metal oxide solar absorbers are well suited for photoelectrochemical applications where requisite properties include stability in highly oxidizing environments, in addition to solar energy conversion. Metal vanadates are of particular interest due to their relatively low band gap energies compared to traditional, wide-gap photocatalysts. Concerted efforts on BiVO 4 -based photoanodes have revealed multiple avenues for improving the solar conversion efficiencies for photon energies above 2.5 eV but have not addressed the ultimate performance limitations from the undesirably high band gap energy. Fe and Cr vanadates have a lower band gap and thus a higher potential solar conversion efficiency, although to-date the absorbed 2–2.5 eV photons are not effectively converted to the desired anodic photocurrent. By using combinatorial synthesis and high throughput screening, we demonstrate that cation substitutions with the monoclinic MVO 4 phase (M = Cr, Fe) improves the utilization of photons in this energy range. Given the portfolio of photoanode improvement techniques available, we suggest optimization of (Cr 0.5 Fe 0.5 )VO 4 -based photoanodes as a promising path for enable solar fuel technologies.

14 SOLAR ENERGY↗
DOE OSTI2024

Defect Properties, Anion Ordering, and Photochromic Mechanism in Yttrium Oxyhydride

Yttrium oxyhydride (YHO) undergoes a reversible photochromic transition when exposed to ultraviolet light. However, the mechanism for this transformation is not fully understood, and the structure and precise chemical composition of YHO remain under debate. Here, we use first-principles density functional theory calculations with a hybrid functional to study the structure, chemical stability, and point defect properties of YHO. As experiments have shown, we find that YHO prefers a cubic structure, with H and O anions present in equal concentrations and located on tetrahedral sites. Stoichiometric and ordered YHO is chemically stable, but it has a wide band gap of 5.01 eV, considerably larger than that measured in experiments (2.4–3.8 eV). On the other hand, Y4H10O has a smaller band gap of 2.97 eV and also has a region of chemical stability; thus, the actual material may include some fraction of this H-rich structure. The defect chemistry of YHO is dominated by anionic antisite species (H O and O H ), with hydrogen interstitials (H i ) and vacancies (V H ) also present in reasonably high concentrations. We show that antisite disorder lowers the band gap relative to the perfectly ordered structure, bringing the magnitude of the gap into closer agreement with experiment. Based on our calculations of defect migration and the positions of defect states relative to the band edges, we link the onset of photochromic behavior to the reaction H O – → V O 0 + H i – , which follows photoexcitation of a H O + defect. H i – can subsequently migrate away and be trapped by additional H O + defects, contributing to the persistence of the reaction, while the resultant oxygen vacancy, V O 0 , introduces an occupied defect state that leads to optical absorption at visible wavelengths. Our results can explain reported discrepancies between experimental and computational results for YHO, and they allow us to propose specific atomic-scale processes that can lead to photochromism. In conclusion, understanding these mechanisms is key for unlocking YHO’s application in devices ranging from smart windows and optoelectronics to electrochemical synapses for neural networks.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS2001

Band Anticrossing in Highly Mismatched Compound Semiconductor Alloys

Compound semiconductor alloys in which metallic anions are partially replaced with more electronegative isoelectronic atoms have recently attracted significant attention. Group IIIN(x)V(1-x), alloys with a small amount of the electronegative N substituting more metallic column V elements has been the most extensively studied class of such Highly Mismatched Alloys (HMAs). We have shown that many of the unusual properties of the IIIN(x),V(1-x) alloys can be well explained by the Band Anticrossing (BAC) model that describes the electronic structure in terms of an interaction between highly localized levels of substitutional N and the extended states of the host semiconductor matrix. Most recently the BAC model has been also used to explain similar modifications of the electronic band structure observed in Te-rich ZnS(x)Te(l-x) and ZnSe(Y)Te(1-y) alloys. To date studies of HMAs have been limited to materials with relatively small concentrations of highly electronegative atoms. Here we report investigations of the electronic structure of ZnSe(y)Te(1-y) alloys in the entire composition range, 0 less than or equal to y less than or equal to 1. The samples used in this study are bulk ZnSe(y)Te(1-y) crystals grown by either a modified Bridgman method or by physical vapor transport. Photomodulated reflection (PR) spectroscopy was used to measure the composition dependence of optical transitions from the valence band edge and from the spin-orbit split off band to the conduction band. The pressure dependence of the band gap was measured using optical absorption in a diamond anvil cell. We find that the energy of the spin-orbit split off valence band edge does not depend on composition and is located at about 3 eV below the conduction band edge of ZnSe. On the Te-rich side the pressure and the composition dependence of the optical transitions are well explained by the BAC model which describes the downward shift of the conduction band edge in terms of the interaction between localized Se states and the conduction band. On the other hand we show that the large band gap reduction observed on the Se-rich side of the alloy system is a result of an interaction between the localized Te level and the valence bands. This interaction leads to the formation of a Te-like valence band edge that strongly interacts with the light hole valence band. Calculations based on a modified k p model account for the reduction of the band gap and the large increase of the spin-orbit splitting observed in Se-rich ZnSe(y)Te(l-y) alloys. We will also discuss the importance of these new results for understanding of the electronic structure and band offsets in other highly mismatched alloy systems.

Yu, Kin Man↗
NASA NTRS2001

Band Anticrossing in Highly Mismatched Compound Semiconductor Alloys

Compound semiconductor alloys in which metallic anions are partially replaced with more electronegative isoelectronic atoms have recently attracted significant attention. Group IIIN(sub x)V(sub 1-x) alloys with a small amount of the electronegative N substituting more metallic column V elements has been the most extensively studied class of such Highly Mismatched Alloys (HMAs). We have shown that many of the unusual properties of the IIIN(sub x)V(sub 1-x) alloys can be well explained by the Band Anticrossing (BAC) model that describes the electronic structure in terms of an interaction between highly localized levels of substitutional N and the extended states of the host semiconductor matrix. Most recently the BAC model has been also used to explain similar modifications of the electronic band structure observed in Te-rich ZnS(sub x)Te(sub 1-x) and ZnSe(sub y)Te(sub 1-y) alloys. To date studies of HMAs have been limited to materials with relatively small concentrations of highly electronegative atoms. Here we report investigations of the electronic structure of ZnSe(sub y)Te(sub 1-y) alloys in the entire composition range, y between 0 and 1. The samples used in this study are bulk ZnSe(sub y)Te(sub 1-y) crystals grown by either a modified Bridgman method or by physical vapor transport. Photomodulated reflection (PR) spectroscopy was used to measure the composition dependence of optical transitions from the valence band edge and from the spin-orbit split off band to the conduction band. The pressure dependence of the band gap was measured using optical absorption in a diamond anvil cell. We find that the energy of the spin-orbit split off valence band edge does not depend on composition and is located at about 3 eV below the conduction band edge of ZnSe. On the Te-rich side the pressure and the composition dependence of the optical transitions are well explained by the BAC model which describes the downward shift of the conduction band edge in terms of the interaction between localized Se states and the conduction band. On the other hand we show that the large band gap reduction observed on the Se-rich side of the alloy system is a result of an interaction between the localized Te level and the valence bands. This interaction leads to the formation of a Te-like valence band edge that strongly interacts with the light hole valence band. Calculations based on a modified k(sup dot)p model account for the reduction of the band gap and the large increase of the spin-orbit splitting observed in Se-rich ZnSe(sub y)Te(sub 1-y) alloys. We will also discuss the importance of these new results for understanding of the electronic structure and band offsets in other highly mismatched alloy systems.

Yu, Kin Man↗
NASA NTRS1995

Recent Developments in Quantum-Well Infrared Photodetectors

Intrinsic infrared (IR) detectors in the long wavelength range (8-20 Am) are based on an optically excited interband transition, which promotes an electron across the band gap (E(sub g)) from the valence band to the conduction band as shown. These photoelectrons can be collected efficiently, thereby producing a photocurrent in the external circuit. Since the incoming photon has to promote an electron from the valence band to the conduction band, the energy of the photon (h(sub upsilon)) must be higher than the E(sub g) of the photosensitive material. Therefore, the spectral response of the detectors can be controlled by controlling the E(sub g) of the photosensitive material. Examples for such materials are Hg(1-x), Cd(x), Te, and Pb(1-x), Sn(x), Te, in which the energy gap can be controlled by varying x. This means detection of very-long-wavelength IR radiation up to 20 microns requires small band gaps down to 62 meV. It is well known that these low band gap materials, characterized by weak bonding and low melting points, are more difficult to grow and process than large-band gap semiconductors such as GaAs. These difficulties motivate the exploration of utilizing the intersub-band transitions in multiquantum well (MQW) structures made of more refractory large-band gap semiconductors. The idea of using MQW structures to detect IR radiation can be explained by using the basic principles of quantum mechanics. The quantum well is equivalent to the well-known particle in a box problem in quantum mechanics, which can be solved by the time independent Schroudiner equation.

Gunapala, S. D.↗
DOE OSTI2025

Stability, electronic quantum states, and magnetic interactions of Er 3+ ions in Ga 2 ⁢O 3

Here, we report an ab initio study of phase stability, defect formation, electronic structure, and multiple magnetic, Dzyaloshinskii-Moriya, optical, hyperfine, and crystal field interactions in erbium (Er)-doped wide band gap 𝛼- and 𝛽-gallium oxides (Ga 2 ⁢O 3 ), critically important to make a foundation for both optoelectronic and quantum information applications. The chemical, structural, mechanical, and dynamical stabilities of the pristine phases are confirmed from respective negative formation energies, negative cohesive energies, favorable elastic constants, and positive phonon frequencies. The phonon dispersions indicate that the Ga-O bonds are uniform in the 𝛼-phase, while they vary in the 𝛽-phase due to the anisotropic polyhedral movement. The defect formation energy analysis confirms that both Er-doped 𝛼- and 𝛽−Ga 2 ⁢O 3 prefer Er 3+ (neutral) state. The underestimated band gaps of the pristine phases from standard density functional theory (DFT) calculations as compared to experimental values are corrected by employing the hybrid functional calculations, resulting in the indirect band gaps of 5.21 eV in 𝛼−Ga 2 ⁢O 3 and 4.94 eV in 𝛽−Ga 2 ⁢O 3 . The site preference energy analysis indicates partial occupation of Er in the octahedral site of Ga. The anisotropic nature of hyperfine tensor coefficients of Er is similar in both phases, which may be due to the occupation of Er in the same octahedral Ga site. On the other hand, the calculated magnetic exchange interaction between two Er dopants is negative for 𝛼 and positive for 𝛽, indicating an antiferromagnetic (AFM) ground state in the former and a ferromagnetic (FM) ground state in the latter. Large values of Dzyaloshinskii-Moriya interactions (DMIs) are obtained along the 𝑥 direction in the 𝛼 and along the 𝑦 direction in the 𝛽. The large DMI may support exotic magnetic textures, a promising direction for spintronic applications. The analysis of dielectric constants and refractive indices of both pristine and Er-doped phases shows a good agreement with available experimental values. The calculated optical anisotropy is slightly higher in 𝛽 than those in 𝛼, which is due to the involvement of lower symmetry in 𝛽. The crystal field coefficients (CFCs) calculated from DFT are used to analyze 4⁢𝑓 multiplets and 4⁢𝑓 −4⁢𝑓 transitions. Thus calculated lowest energy level of the first excited state to the lowest energy level of the ground state is about 1.53 µ⁢m, which is in a good agreement with available experiments, and it falls within the quantum telecommunication wavelength range.

3-dimensional systems↗
DOE OSTI2023

Trap-Assisted Auger-Meitner Recombination from First Principles

Trap-assisted nonradiative recombination is known to limit the efficiency of optoelectronic devices, but the conventional multiphonon emission (MPE) process fails to explain the observed loss in wide-band-gap materials. Here, we highlight the role of trap-assisted Auger-Meitner (TAAM) recombination and present a first-principles methodology to determine TAAM rates due to defects or impurities in semiconductors or insulators. We assess the impact on efficiency of light emitters in a recombination cycle that may include both TAAM and carrier capture via MPE. We apply the formalism to the technologically relevant case study of a calcium impurity in InGaN, where a Shockley-Read-Hall recombination cycle involving MPE alone cannot explain the experimentally observed nonradiative loss. We find that, for band gaps larger than 2.5 eV, the inclusion of TAAM results in recombination rates that are orders of magnitude larger than recombination rates based on MPE alone, demonstrating that TAAM can be a dominant nonradiative process in wide-band-gap materials. Furthermore, our computational formalism is general and can be applied to the calculation of TAAM rates in any semiconducting or insulating material.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Synthetic Pathways to gamma-Graphyne and Related Allotropes of Carbon

Graphynes, two-dimensional carbon lattices combining sp 1 and sp 2 hybridized atoms, were predicted theoretically more than three decades ago, but few structures have been realized to date. These carbons are believed to possess remarkable mechanical and electronic properties, including high charge carrier mobilities comparable to those in graphene (10 4 to 10 5 cm 2 V -1 s -1 ). Unlike graphene, certain graphynes are predicted to be intrinsic semiconductors. Among these intriguing structures, γ-graphyne stands out as the structurally simplest and most symmetric sp 1 /sp 2 lattice. γ-Graphyne was first theorized in 1987. In contrast with graphene, γ-graphyne will be a semiconductor with a small band gap suitable for fabrication of electronic devices. This solves one of the fundamental problems of carbon-based electronics, the necessity for inducing a band gap in graphene. γ-Graphyne has the potential to form the basis for the next generation of carbon-based electronics operating at speeds unattainable by traditional silicon chips. Unlike silicon, γ-graphyne is a direct band gap semiconductor, and it will feature exceptional strength comparable to that of other 2D carbon allotropes. Such combination of properties may enable a new generation of highly efficient, ultra-light and flexible solar cells. Despite being a potentially “magical” material, γ-graphyne remained synthetically elusive for over three decades. The primary goals of this project were: (1) Synthesis of bulk γ-graphyne phases through solution-phase 2D polymerizations; (2) Experimental exploration of the physical and chemical properties of γ-graphyne; and (3) Mechanistic and theoretical studies of the novel chemical transformations developed in Goal 1. Common pyrolytic and vapor-deposition methodologies used for the synthesis of graphitic allotropes are unsuitable for graphyne and other sp 1 -contaning structures, as acetylenes readily convert to graphene and amorphous carbon at high temperatures. In contrast, this proposal is based on solution-based 2D polymerization. The major advantages of this approach over the traditional high temperature techniques are the potential to adjust the structure of the material with atomic precision, and the possibility of using structurally complex and relatively fragile repeat units. The outcomes of this research can revolutionize carbon nanotechnology, expanding the field’s structural toolbox beyond primarily graphitic and benzenoid structures. Understanding the chemistry of sp 1 carbon allotropes can lead to entirely new classes of structures with unique properties, including graphyne ribbons, nanotubes, quantum dots, and heterostructures with other 2D materials. Furthermore, the development of reliable and robust synthetic pathways towards periodic covalent molecular sheets with atomically precise structures shall have a profound impact on chemistry and materials science.

2D polymerization↗
DOE OSTI2025

Orthorhombic Structures as Inorganic Halide Perovskite Models for High-Throughput DFT Investigations

Although high-symmetry Pm-3m space group cubic models are computationally efficient for high-throughput density functional theory (DFT) calculations of inorganic ternary (ABX 3 ) halide perovskites (HPs), they frequently predict band gaps (E g ) that disagree with experiment. Conversely, while low-symmetry cubic polymorphous networks (PN) comprised of 160 to 320 atoms incur significantly greater computational cost, they predict E g ’s that are more closely aligned with experiment. Here, in this study, we compare the DFT total energies and E g ’s predicted by four high-symmetry structure models (Pnma orthorhombic, R3m trigonal, P4/mbm tetragonal, and Pm-3m cubic) to cubic PNs for 5 experimentally characterized ternary HPs and find that the orthorhombic model computes Eg’s with the smallest MAD of 0.23 eV relative to the PNs. Pair distribution functions and DFT-computed total energies show that octahedral tilting, which is present in the 20-atom orthorhombic and 160-atom cubic PN models but not in the 5-atom cubic models, stabilizes all 5 compositions in our benchmarking set. We also find that imposing PN constraints when generating and optimizing these orthorhombic structures by fixing the unit cell lattice vectors and displacing the atoms prior to ionic relaxation with DFT, which we call the orthorhombic surrogate model (OSM), lowers the MAD of E g predictions to 0.09 eV. Our OSM predicts the PN band gaps of an additional 95 theoretical inorganic ternary HPs with MAD of 0.08 eV, supporting its usage in high-throughput DFT investigations to closely estimate PN band gaps with much less computational expense.

14 SOLAR ENERGY↗
DOE OSTI2023

α-Quartz Phase Stabilization, Surface Texturing, and Tunable Optical Properties of Nanocrystalline GeO 2 Films Made by Pulsed-Laser Deposition: Implications for Optical and Optoelectronic Applications

Germanium oxide (GeO 2 ) has great potential in multifunctional devices and next-generation power electronics due to its high thermal conductivity and ambipolar doping capability. However, the complexity of synthesizing the desirable polymorph with a controlled phase, surface/interface quality, microstructure, and functional properties is the main barrier to GeO 2 utilization in advanced applications. Here, in this regard, we present a method to realize the hexagonal (h) or a-quartz type GeO 2 with nano-textured surface morphology on sapphire substrates using a hybrid synthesis strategy that comprises pulsed laser deposition (PLD) and post-deposition thermal annealing. We performed a comprehensive study to investigate the effect of annealing temperature, which was varied in a wide range (600-1100 °C), on the crystal structure, phase, surface morphology, chemical stoichiometry, defect states, and optical properties of PLD-grown GeO 2 films. As-deposited GeO 2 films at 500 °C were amorphous. Upon annealing, the GeO 2 films induced an amorphous-to-crystalline phase transformation; GeO 2 films annealed at higher annealing temperatures (≥900 °C) stabilized in the hexagonal phase and demonstrated excellent crystal quality and chemical stability. Thermally activated growth process showed increased average crystallite size, which was varied in the range of 20-130 (±2) nm, while the surface roughness followed a similar trend. The spectral transmittance and band gap also increased with increasing annealing temperature. The resulting h-GeO 2 films, particularly those obtained at annealing temperatures in the 900-1100 °C range, had a higher band gap of 6.2-6.3 eV and displayed excellent optical transmittance in the visible region. Moreover, the absence of extended valence band maxima and reduced optical defect density support the quality improvement upon annealing. When considering phase-pure bulk and nanostructured GeO 2 as a possible candidate for ultra wide band gap semiconductors in cutting-edge technological applications, the results of the current work can be beneficial to realize high structural and optical quality a-quartz structured GeO 2 films.

GeO2↗
DOE OSTI2021

World Record Demonstration of > 30% Thermophotovoltaic Conversion Efficiency

Thermophotovoltaic (TPV) devices are solid-state heat engines that convert thermal radiation into electricity using semiconductor diodes, and have applications in energy storage, primary power conversion, and waste heat recovery. Higher temperature emitters and wider band gap photovoltaics (PVs) generally afford higher TPV efficiencies. High temperature emitters are accessible in thermal energy storage applications. We have demonstrated a world record 31% +/- 2% TPV conversion efficiency with a 0.9 cm2 GaAs-based PV device under a 2430 °C thermal emitter, producing an electrical output power of 2.23 W. Critical to the result was the cell’s high reflectance of photon energies below the device band gap. Unlike solar PV, for which sub-band gap (SBG) light is lost, a TPV cell can reflect and recycle SBG light to the thermal emitter. The demonstration was made on a custom-built measurement platform in which a ~100 cm2 graphite thermal emitter was heated under vacuum up to 2430 °C. The TPV efficiency was evaluated by comparing the measured electrical output power of the TPV with the calorimetrically measured total net power incident on the cell. The measured TPV efficiency as a function of thermal emitter temperature was corroborated by our full system modeling predictions. As far as the authors are aware, this is the highest TPV conversion efficiency ever measured, and device improvements should yield > 40% efficiency in the near future.

27 ARPA - Advanced Research Projects Agency-Energy↗
NASA NTRS1989

Optical evidence for the metallization of Xenon at 132(5) GPa

Xe has been compressed in a diamond-anvil cell to approximately 200 GPa. The metallization of Xe by band-gap closure was investigated by obtaining optical data in both the metallic and insulating states. In the metallic state, the pressure dependence of the plasma frequency was determined from absorption data fitted with a free-electron model. In the insulating state, the pressure dependence of the band gap was determined from absorption data fitted with an indirect-band-gap model. The optical data indicate that the insulator-to-metal transition in Xe occurs at 132(5) GPa.

Goettel, Kenneth A.↗
DOE OSTI2023

Suppressed phase segregation for triple-junction perovskite solar cells

The tunable band gaps and facile fabrication of perovskites make them attractive for multi-junction photovoltaics. However, light-induced phase segregation limits their efficiency and stability: this occurs in wide band gap (> 1.65 eV) I/Br mixed perovskite absorbers, and becomes even more acute in the top cells of triple-junction solar photovoltaics that requires a fully 2.0 eV band gap absorber. We report herein that lattice distortion in I/Br mixed perovskites is correlated with the suppression of phase segregation, generating an increased ion migration energy barrier arising from the decreased average interatomic distance between A-site cation and iodide. Using a ~2.0 eV Rb/Cs mixed-cation inorganic perovskite with large lattice distortion in the top subcell, we fabricated all-perovskite triple-junction solar cells and achieved an efficiency of 24.3% (23.3% certified quasi-steady-state efficiency) with an open-circuit voltage of 3.21 V. This is, to our knowledge, the first reported certified efficiency for perovskite-based triple-junction solar cells. The triple-junction devices retain 80% of their initial efficiency following 420 hours of operation at the maximum power point.

14 SOLAR ENERGY↗
DOE OSTI2022

High-throughput predictions of metal–organic framework electronic properties: theoretical challenges, graph neural networks, and data exploration

Abstract With the goal of accelerating the design and discovery of metal–organic frameworks (MOFs) for electronic, optoelectronic, and energy storage applications, we present a dataset of predicted electronic structure properties for thousands of MOFs carried out using multiple density functional approximations. Compared to more accurate hybrid functionals, we find that the widely used PBE generalized gradient approximation (GGA) functional severely underpredicts MOF band gaps in a largely systematic manner for semi-conductors and insulators without magnetic character. However, an even larger and less predictable disparity in the band gap prediction is present for MOFs with open-shell 3 d transition metal cations. With regards to partial atomic charges, we find that different density functional approximations predict similar charges overall, although hybrid functionals tend to shift electron density away from the metal centers and onto the ligand environments compared to the GGA point of reference. Much more significant differences in partial atomic charges are observed when comparing different charge partitioning schemes. We conclude by using the dataset of computed MOF properties to train machine-learning models that can rapidly predict MOF band gaps for all four density functional approximations considered in this work, paving the way for future high-throughput screening studies. To encourage exploration and reuse of the theoretical calculations presented in this work, the curated data is made publicly available via an interactive and user-friendly web application on the Materials Project.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Chemical manipulation of hydrogen induced high p-type and n-type conductivity in Ga 2 O 3

Advancement of optoelectronic and high-power devices is tied to the development of wide band gap materials with excellent transport properties. However, bipolar doping (n-type and p-type doping) and realizing high carrier density while maintaining good mobility have been big challenges in wide band gap materials. Here P-type and n-type conductivity was introduced in β-Ga 2 O 3 , an ultra-wide band gap oxide, by controlling hydrogen incorporation in the lattice without further doping. Hydrogen induced a 9-order of magnitude increase of n-type conductivity with donor ionization energy of 20 meV and resistivity of 10 -4 Ω.cm. The conductivity was switched to p-type with acceptor ionization energy of 42 meV by altering hydrogen incorporation in the lattice. Density functional theory calculations were used to examine hydrogen location in the Ga 2 O 3 lattice and identified a new donor type as the source of this remarkable n-type conductivity. Positron annihilation spectroscopy measurements confirm this finding and the interpretation of the experimental results. This work illustrates a new approach that allows a tunable and reversible way of modifying the conductivity of semiconductors and it is expected to have profound implications on semiconductor field. At the same time, it demonstrates for the first time p-type and remarkable n-type conductivity in Ga 2 O 3 which should usher in the development of Ga 2 O 3 devices and advance optoelectronics and high-power devices.

36 MATERIALS SCIENCE↗
DOE OSTI2021

First-Principles Study on the Electronic Properties of PDPP-Based Conjugated Polymer via Density Functional Theory

In this study, we focus on computational predictions of the electronic and optical properties of a one-dimensional periodic model of a single chain of a diketopyrrolopyrrole (DPP)-based conjugated polymer (PDPP3T) as a function of electronic configuration changes due to charge injection. Here, we employ density functional theory (DFT) to explore the ground-state and excited-state electronic properties as well as optical properties influenced by charge injection. We utilize both the Heyd–Scuseria–Ernzerhof (HSE06) and Perdew–Burke–Ernzerhof (PBE) functionals to predict the band gap and compute the absorption spectrum. Our DFT results point out that utilizing the HSE06 functional in conjunction with momentum sampling over the Brillouin zone can appropriately predict the band gap and absorption spectrum in good agreement with experimental data. Moreover, we explore the influence of charge-carrier injection on the electronic configuration of the PDPP3T polymer. Our results indicate that the injection of charge carriers into the PDPP3T semiconducting polymer model greatly affects the electrical properties and ends in a low band gap and high mobility of charge carriers in PDPP3T polymers, offering the potential to tailor the material electronic performance for organic photovoltaic and optoelectronic device applications.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2024

Controlling the orbital Hall effect in gapped bilayer graphene in the terahertz regime

We study the orbital Hall effect (OHE) in the AC regime using bilayer graphene (BLG) as a prototypical material platform. While the unbiased BLG has gapless electronic spectra, applying a perpendicular electric field creates an energy band gap that can be continuously tuned from zero to high values. By exploiting this flexibility, we demonstrate the ability to control the behavior of AC orbital Hall conductivity. Particularly, we demonstrate that the orbital Hall conductivity at the neutrality point changes its signal at a critical frequency, the value of which is proportional to the perpendicular electric field. For BLG with narrow band gaps, the active frequency region for the AC OHE may extend to a few terahertz, which is experimentally accessible with current technologies. We also consider the introduction of a perpendicular magnetic field in the weak-coupling regime using first-order perturbation theory to illustrate how the breaking of time-reversal symmetry enables the emergence of the AC charge Hall effect in the charge-doped situation and modifies the AC orbital Hall conductivity. Our calculations suggest that BLG with narrow band gaps is a practical candidate for investigating time-dependent orbital angular momentum transport. Published by the American Physical Society 2024

36 MATERIALS SCIENCE↗