Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “BaO”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Effect of Molecular Weight on the Morphology of a Polymer Semiconductor–Thermoplastic Elastomer Blend

Abstract Polymer semiconductors (PSCs) are essential active materials in mechanically stretchable electronic devices. However, many exhibit low fracture strain due to their rigid chain conformation and the presence of large crystalline domains. Here, a PSC/elastomer blend, poly[((2,6‐bis(thiophen‐2‐yl)‐3,7‐bis(9‐octylnonadecyl)thieno[3,2‐b]thieno[2′,3′:4,5]thieno[2,3‐d]thiophene)‐5,5′‐diyl)(2,5‐bis(8‐octyloctadecyl)‐3,6‐di(thiophen‐2‐yl)pyrrolo[3,4‐c]pyrrole‐1,4‐dione)‐5,5′‐diyl]] (P2TDPP2TFT4) and polystyrene‐ block ‐poly(ethylene‐ran‐butylene)‐ block ‐polystyrene (SEBS) are systematically investigated. Specifically, the effects of molecular weight of both SEBS and P2TDPP2TFT4 on the resulting blend morphology, mechanical, and electrical properties are explored. In addition to commonly used techniques, atomic force microscopy‐based nanomechanical images are used to provide additional insights into the blend film morphology. Opposing trends in SEBS‐induced aggregation are observed for the different P2TDPP2TFT4 molecular weights upon increasing the SEBS molecular weight from 87 to 276 kDa. Furthermore, these trends are seen in device performance trends for both molecular weights of P2TDPP2TFT4. SEBS molecular weight also has a substantial influence on the mesoscale phase separation. Strain at fracture increases dramatically upon blending, reaching a maximum value of 640% ± 20% in the blended films measured with film‐on‐water method. These results highlight the importance of molecular weight for electronic devices. In addition, this study provides valuable insights into appropriate polymer selections for stretchable semiconducting thin films that simultaneously possess excellent mechanical and electrical properties.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Enabling Deformable and Stretchable Batteries

Abstract Deformable energy storage devices are needed to power next‐generation wearable electronics that interface intimately with human skin. Currently, deformable energy storage devices demonstrate poor performance compared to their rigid lithium‐ion counterparts, forcing wearable manufacturers to design their devices around bulky battery compartments. However, technological advances to create deformable batteries at the component and device level have yielded continuous improvement in stretchable batteries over the last five years. In this Essay, the major strategies at the component and device level that have been successfully employed to create stretchable batteries are reviewed. The outstanding challenges facing deformable energy storage are also discussed, namely, energy density, packaging, delamination, device integration, and manufacturing. This Essay will give researchers who are interested in contributing to the development of deformable batteries a cursory understanding of the most successful strategies to date, and provide insights into the most important directions to pursue in the future.

Mackanic, David G.↗
DOE OSTI2020

Direct Characterization of Atomically Dispersed Catalysts: Nitrogen-Coordinated Ni Sites in Carbon-Based Materials for CO 2 Electroreduction

Metal, nitrogen-doped carbon materials have attracted interest as heterogenous catalysts that contain MN x active sites that are analogous to molecular catalysts. Of particular interest is Ni,N-doped carbon, a catalyst that is active for the electrochemical reduction of CO 2 to CO. Critical to the understanding of these materials is proof of single atomic sites and characterization of the environment surrounding the metal atom; however, directly probing this coordination remains challenging. This challenge is addressed in this study by combining scanning transmission electron microscopy (STEM), single atom electron energy loss spectroscopy (EELS), and time-of-flight secondary ion mass spectrometry (ToF-SIMS). Through STEM imaging, atomic dispersion of Ni in the carbon framework is confirmed and image analyses are utilized to give semiquantitative estimates of neighbor distance distributions and site densities of Ni atoms. Atomic resolution EELS demonstrates that N and Ni are colocated at the single Ni atom sites suggesting Ni–N coordination. ToF-SIMS reveals a distribution of NiN x C y - fragments that reflect the Ni–N bonding environments within Ni,N-doped carbon. The fragmentation from Ni,N-doped carbon is similar to Ni phthalocyanine, suggesting the existence of heterogenized, molecular-like NiN 4 active sites which motivates future studies that leverage insight from molecular catalysis design to develop next-generation heterogeneous catalysts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Polymers in Lithium‐Ion and Lithium Metal Batteries

Abstract Lithium‐ion batteries play a significant role in modern electronics and electric vehicles. However, current Li‐ion battery chemistries are unable to satisfy the increasingly heightened expectations regarding energy demand and reliability. To boost the overall energy density while ensuring the safety of Li batteries, researchers have focused on alternative battery materials, such as silicon, sulfur, and Li metal. These represent promising avenues, although numerous obstacles (e.g., Si cracking, polysulfide shuttling, Li dendrites, etc.) must be tackled before batteries based on these materials can enter mass production and penetrate the mainstream market. Polymers are a class of materials that are widely used in current battery systems; however, many novel polymer chemistries may offer better performance and reliability than the current ones, and even overcome the issues of the above‐mentioned new battery materials. In this review, selected polymeric materials for solving these issues are categorized into four parts: polymer electrolytes, polymer artificial solid‐electrolyte interphases, binders, and separators. Both the current progress and the characterization methods are included. Potential future directions of energy materials research are pointed out as well.

Li, Junheng↗
DOE OSTI2021

Mesocrystallizing Nanograins for Enhanced Li + Storage

Morphology and crystallinity of electrode materials have a major effect on their charge carrier storage properties when applied in rechargeable batteries. While nanosizing electrode particles (with larger surface area) and maintaining electrode integrity are both good for performance enhancement, they seem to contradict each other and can be hardly well-balanced. Herein, we designed electrode particles consisting of numerous nanograins with uniform crystalline orientation to guarantee both high surface area and high structural integrity, allowing the significant improvement of Li + storage kinetics and performance. Applying this “mesocrystallizing” strategy to a NiCo 2 O 4 -based anode, resulting in various degrees of pseudocapacitance response, the long-term cyclability and rate performance of this material have been largely enhanced. Impressively, the mesocrystalline NiCo 2 O 4 electrode exhibits a high reversible capacity of 1403 mAh g -1 after 200 cycles at 1.6 A g -1 (a rate of 1.8 C). The growth mechanism of mesocrystalline materials with different morphologies is identified to be a topotactic strctural transition process featuring a gradual edge-to-core corrasion process. This work presents an important synthetic clue to balance the morpholgy and crystallinity of battery electrode materials for their perforamnce optimization and is expected to inspire future structural design for battery materials beyond the one prototyped here.

25 ENERGY STORAGE↗
DOE OSTI2021

A Nickel-Decorated Carbon Flower/Sulfur Cathode for Lean-Electrolyte Lithium–Sulfur Batteries

Lithium–sulfur (Li–S) batteries involve a reversible conversion reaction between sulfur and lithium sulfide (Li 2 S) via a series of soluble lithium polysulfide intermediates (LiPSs), enabling a high theoretical specific capacity of 1675 mAh g –1 . However, this process exhibits large polarization and low sulfur utilization and suffers critical capacity fade. The primary approach to tackle the problem has so far been to infiltrate sulfur into nanostructured carbon. Furthermore, most studies using porous carbon as host materials have tested with high electrolyte to sulfur ratios (E/S) (generally > 15 µL mg –1 ) that compromise the cell-level energy density. Here, a flower-shaped porous carbon structure with nickel nanoparticles that can address the problems discussed above is designed. First, the 3D flower-shaped carbon structure enables short ionic transport lengths. Second, the small pore diameters <10 nm and high specific surface areas > 3300 m 2 g –1 with sufficient pore volume are ideal for charging performance for low E/S ratios. Finally, Ni nanoparticles are employed onto the flower-shaped network to improve the reaction kinetics. Collectively, it is successfully demonstrated that the batteries with a high mass loading of 5 mg cm –2 and a 5 µL mg –1 E/S ratio can retain cycle retention of 70% after 150 cycles.

25 ENERGY STORAGE↗
DOE OSTI2021

Revisiting Discharge Mechanism of CF x as a High Energy Density Cathode Material for Lithium Primary Battery

Lithium/fluorinated graphite (Li/CFx) primary batteries show great promise for applications in a wide range of energy storage systems due to their high energy density (>2100 Wh kg –1 ) and low self-discharge rate (<0.5% per year at 25 °C). While the electrochemical performance of the CF x cathode is indeed promising, the discharge reaction mechanism is not thoroughly understood to date. In this article, a multiscale investigation of the CF x discharge mechanism is performed using a novel cathode structure to minimize the carbon and fluorine additives for precise cathode characterizations. Titration gas chromatography, X-ray diffraction, Raman spectroscopy, X-ray photoelectron spectroscopy, scanning electron microscopy, cross-sectional focused ion beam, high-resolution transmission electron microscopy, and scanning transmission electron microscopy with electron energy loss spectroscopy are utilized to investigate this system. Results show no metallic lithium deposition or intercalation during the discharge reaction. Crystalline lithium fluoride particles uniformly distributed with <10 nm sizes into the CF x layers, and carbon with lower sp2 content similar to the hard-carbon structure are the products during discharge. This article deepens the understanding of CF x as a high energy density cathode material and highlights the need for future investigations on primary battery materials to advance performance.

25 ENERGY STORAGE↗
DOE OSTI2022

Twisted A-D-A Type Acceptors with Thermally-Activated Delayed Crystallization Behavior for Efficient Nonfullerene Organic Solar Cells

We report that molecular aggregation and crystallization during film coating play a crucial role in the realization of high-performing organic photovoltaics. Strong intermolecular interactions and high solid-state crystallinity are beneficial for charge transport. However, fast crystallization during thin-film drying often limits the formation of the finely phase-separated morphology required for efficient charge generation. Herein, the authors show that twisted acceptor-donor-acceptor (A-D-A) type compounds, containing an indacenodithiophene (IDT) electron-rich core and two naphthalenediimide (NDI) electron-poor units, leads to formation of mostly amorphous phases in the as-cast film, which can be readily converted into more crystalline domains by means of thermal annealing. This design strategy solves the aforementioned conundrum, leading to an optimal morphology in terms of reduced donor/acceptor domain-separation sizes (ca. 13 nm) and increased packing order. Solar cells based on these acceptors with a PBDB-T polymer donor show a power conversion efficiency over 10% and stable morphology, which results from the combined properties of desirable excited-state dynamics, high charge mobility, and optimal aggregation/crystallization characteristics. These results demonstrate that the twisted A-D-A motif featuring thermally-induced crystallization behavior is indeed a promising alternative design approach toward more morphologically robust materials for efficient organic photovoltaics.

14 SOLAR ENERGY↗
DOE OSTI2022

A Solution-Processable High-Modulus Crystalline Artificial Solid Electrolyte Interphase for Practical Lithium Metal Batteries

The solid electrolyte interphase (SEI) has been identified as a key challenge for Li metal anodes. The brittle and inhomogeneous native SEI generated by parasitic reactions between Li and liquid electrolytes can devastate battery performance; therefore, artificial SEIs (ASEIs) have been proposed as an effective strategy to replace native SEIs. Herein, as a collaboration between academia and industrial R&D teams, a multifunctional (crystalline, high modulus, and robust, Li + ion conductive, electrolyte-blocking, and solution processable) ASEI material, LiAl-FBD (where “FBD” refers to 2,2,3,3-tetra-fluoro-1,4-butanediol), for improving Li metal battery performance is designed and synthesized. The LiAl-FBD crystal structure consists of Al 3+ ions bridged by FBD 2– ligands to form anion clusters while Li + ions are loosely bound at the periphery, enabling an Li + ion conductivity of 9.4 × 10 –6 S cm –1 . Further, the fluorinated, short ligands endow LiAl-FBD with electrolyte phobicity and high modulus. The ASEI is found to prevent side reactions and extend the cycle life of Li metal electrodes. Specifically, pairing LiAl-FBD coated 50 μm thick Li with industrial 3.5 mAh cm –2 NMC811 cathode and 2.8 μL mAh –1 lean elec-trolyte, the Li metal full cells show superior cycle life compared to bare ones, achieving 250 cycles at 1 mA cm –2 .

25 ENERGY STORAGE↗
DOE OSTI2022

Suppressing Chemical Corrosions of Lithium Metal Anodes

In this study, the lithium metal anode is essential for next-generation high-energy-density rechargeable Li-metal batteries. Although extensive studies have been performed to prolong the cycle life of Li-metal batteries, the calendar life, which associates with the chemical corrosion of Li metal in liquid electrolytes, has not been quantitatively understood. Here, by combing the titration gas chromatography method and cryogenic focused ion beam, a quantitative relationship between the chemical corrosion rate and electrochemically deposited Li morphology in various liquid electrolyte systems is established. It has been identified that the corrosion rate is dominated by the porosity of the deposited Li. The larger the porosity of deposited Li has, the faster the corrosion rate will be. Strategies to mitigate the chemical corrosion on Li thus to extend the calendar life of Li-metal batteries are further proposed. By strictly controlling the stacking pressure during Li plating, Li deposits with ultra-low porosity can be achieved, suppressing the corrosion rate to 0.08 ± 0.16%/day compared with 1.71 ± 0.19%/day of the high-porosity Li.

25 ENERGY STORAGE↗
DOE OSTI2022

Enhanced Electrolyte Transport and Kinetics Mitigate Graphite Exfoliation and Li Plating in Fast–Charging Li–Ion Batteries

Despite significant progress in energy retention, lithium-ion batteries (LIBs) face untenable reductions in cycle life under extreme fast-charging (XFC) conditions, which primarily originate from a variety of kinetic limitations between the graphite anode and the electrolyte. Through quantitative Li + loss accounting and comprehensive materials analyses, it is directly observed that the operation of LIB pouch cells at 4 C||C/3 (charging||discharging) results in Li plating, disadvantageous solid-electrolyte-interphase formation, and solvent co-intercalation leading to interstitial decomposition within graphite layers. It is found that these failure modes originate from the insufficient properties of conventional electrolytes, where employing a designed ester-based electrolyte improved the capacity retention of these cells from 55.9% to 88.2% after 500 cycles when operated at the aforementioned conditions. These metrics are the result of effective mitigation of the aforementioned failure modes due to superior Li + transport and desolvation characteristics demonstrated through both experimental and computational characterization. Finally, this work reveals the vital nature of electrolyte design to XFC performance.

25 ENERGY STORAGE↗
DOE OSTI2023

Understanding of Low‐Porosity Sulfur Electrode for High‐Energy Lithium–Sulfur Batteries

Abstract The lithium–sulfur (Li–S) battery is a promising technology for large‐scale energy storage and vehicle electrification due to its high theoretical energy density and low cost. Reducing the sulfur cathode porosity has been identified recently as a viable strategy for improving the cell practical energy density and minimizing pore‐filling electrolytes to extend cell life at lean electrolyte conditions. Direct use of a low‐porosity cathode for Li–S battery results in poor electrode wetting, nonuniform electrode reactions, and thus early cell failure. To understand and mitigate the barriers associated with the use of low‐porosity electrodes, multiscale modeling is performed to predict electrode wetting, electrolyte diffusion, and their impacts on sulfur reactions in Li–S cells by explicitly considering the electrode wettability impacts and electrode morphologies. The study elucidates the critical impact of low tortuosity and large channel pore design for promoting electrode wetting and species diffusion. It is suggested that the secondary particle size should be comparable with the electrode thickness to effectively promote electrolyte wettability and sulfur reactivity. This study provides new insights into the low‐porosity electrode material and designs and is expected to accelerate the development of practical high‐energy Li–S batteries.

25 ENERGY STORAGE↗
DOE OSTI2023

Operando Interaction and Transformation of Metastable Defects in Layered Oxides for Na‐Ion Batteries

Non-equilibrium defects often dictate the macroscopic properties of materials. They largely define the reversibility and kinetics of processes in intercalation hosts in rechargeable batteries. Recently, imaging methods have demonstrated that transient dislocations briefly appear in intercalation hosts during ion diffusion. Despite new discoveries, the understanding of impact, formation and self-healing mechanisms of transient defects, including and beyond dislocations, is lacking. Here, operando X-ray Bragg Coherent Diffractive Imaging (BCDI) and diffraction peak analysis capture the stages of formation of a unique metastable domain boundary, defect self-healing, and resolve the local impact of defects on ionic diffusion in Na x Ni 1-y MnyO 2 intercalation hosts in a charging sodium-ion battery. Results, applicable to a wide range of layered intercalation materials due to the shared nature of framework layers, elucidate new dynamics of transient defects and their connection to macroscopic properties, and suggest how to control the nanostructure dynamics.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Ion Conducting Polymer Interfaces for Lithium Metal Anodes: Impact on the Electrodeposition Kinetics

Electrochemical cells that utilize metals (e.g., lithium, sodium, zinc) as anodes are under intense investigation as they are projected to replace the current lithium-ion batteries to serve as a more energy-dense option for commercial applications. In addition, metal electrodes provide opportunities for fundamental research of different phenomena, such as ion transport and electrochemical kinetics, in the complex environment of reactive metal-electrodeposition. In this work, computationally and experimentally the competing effects related to transport and kinetics during the metal electrodeposition process are examined. Using Brownian dynamics simulations, it is shown that slower deposition kinetics results in a more compact and uniform Li morphology. This finding is experimentally implemented by designing ion-containing polymeric coatings on the electrodes that simultaneously provide pathways for lithium-ion transport, while impeding the charge transfer (Li + + e - → Li) at heterogeneous surfaces. It is further shown that these ionic polymer interfaces can significantly extend the cell-lifetime of a lithium metal battery in both ether-based and carbonate-based electrolytes. Through theoretical and experimental investigations, it is found that a low kinetic to transport rate ratio is a major factor in influencing the Li plating morphology. The plating morphology can be further fine-tuned by increasing ionic conductivity.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Interface Design for High‐Performance All‐Solid‐State Lithium Batteries

All‐solid‐state batteries suffer from high interface resistance and lithium dendrite growth leading to low Li plating/stripping Coulombic efficiency (CE) of <90% and low critical current density at high capacity. Here, in this work, both challenges are simultaneously addressed and the Li plating/stripping CE is significantly increased to 99.6% at 0.2 mA cm −2 /0.2 mAh cm −2 , and critical current density (CCD) of > 3.0 mA cm −2 /3.0 mAh cm −2 by inserting a mixed ionic‐electronic conductive (MIEC) and lithiophobic LiF‐C‐Li 3 N‐Bi nanocomposite interlayer between Li 6 PS 5 Cl electrolyte and Li anode. The highly lithiophobic LiF‐C‐Li 3 N‐Bi interlayer with high ionic conductivity (10 −5 S cm −1 ) and low electronic conductivity (3.4×10 −7 S cm −1 ) enables Li to plate on the current collector (CC) surface rather than on Li 6 PS 5 Cl surface avoiding Li 6 PS 5 Cl electrolyte reduction. During initial Li plating on CC, Li penetrates into porous LiF‐C‐Li 3 N‐Bi interlayer and lithiates Bi nanoparticles into Li 3 Bi. The lithiophilic Li 3 Bi and Li 3 N nanoparticles in LiF‐C‐Li 3 N‐Li 3 Bi sub‐interlayer will move to CC along with plated Li, forming LiF‐C/Li 3 N‐Li 3 Bi lithiophobic/lithiophilic sublayer during the following Li stripping. This interlayer enables Co 0.1 Fe 0.9 S 2 /Li 6 PS 5 Cl/Li cell with an areal capacity of 1.4 mAh cm −2 to achieve a cycle life of >850 cycles at 150 mA g −1 . The lithiophobic/lithiophilic interlayer enables solid‐state metal batteries to simultaneously achieve high energy and long cycle life.

25 ENERGY STORAGE↗
DOE OSTI2024

Design of Star‐Shaped Trimer Acceptors for High‐Performance (Efficiency > 19%), Photostable, and Mechanically Robust Organic Solar Cells

Abstract High power conversion efficiency (PCE), long‐term stability, and mechanical robustness are prerequisites for the commercial applications of organic solar cells (OSCs). In this study, a new star‐shaped trimer acceptor (TYT‐S) is developed and high‐performance OSCs with a PCE of 19.0%, high photo‐stability (t 80% lifetime = 2600 h under 1‐sun illumination), and mechanical robustness with a crack‐onset strain (COS) of 21.6% are achieved. The isotropic molecular structure of TYT‐S affords efficient multi‐directional charge transport and high electron mobility. Furthermore, its amorphous structure prevents the formation of brittle crystal‐to‐crystal interfaces, significantly enhancing the mechanical properties of the OSC. As a result, the TYT‐S‐based OSCs demonstrate a significantly higher PCE (19.0%) and stretchability (COS = 21.6%) than the linear‐shaped trimer acceptor (TYT‐L)‐based OSCs (PCE = 17.5% and COS = 6.4%) and the small‐molecule acceptor (MYT)‐based OSCs (PCE = 16.5% and COS = 1.3%). In addition, the increased molecular size of TYT‐S, relative to that of MYT and dimer (DYT), suppresses the diffusion kinetics of the acceptor molecules, substantially improving the photostability of the OSCs. Finally, to effectively demonstrate the potential of TYT‐S, intrinsically stretchable (IS)‐OSCs are constructed. The TYT‐S‐based IS‐OSCs exhibit high device stretchability (strain at PCE 80% = 31%) and PCE of 14.4%.

Chemistry↗
DOE OSTI2022

The influence of random packed column parameters on the liquid holdup and interfacial area

Abstract Carbon dioxide capture via solvent absorption in packed columns has emerged as a potential technology to mitigate coal‐fired power plant CO 2 emissions. Parameters, including packing types, solvent properties, and operating conditions, could potentially affect the packed column CO 2 capture efficiency. To understand the importance of those parameters and help packed column optimization, a design of experiments (DoEs) method was proposed to generate input parameter matrix. Combined with multiphase computational fluid dynamics (CFD), the random packed column parameter influence on the liquid holdup and interfacial area can be efficiently investigated. Surrogate‐based sensitivity analysis shows that the solvent flow rate and contact angle are key factors dictating liquid holdup and interfacial area. On the other hand, solvent viscosity has a marginal impact on the interfacial area. The sensitivity scores were calculated for each input parameter to guide the selection of dimensionless numbers for the liquid holdup and interfacial area correlation development.

42 ENGINEERING↗
DOE OSTI2020

Risk‐based, response‐adapted therapy for early‐stage extranodal nasal‐type NK /T‐cell lymphoma in the modern chemotherapy era: A China Lymphoma Collaborative Group study

Abstract We aimed to determine the survival benefits of chemotherapy (CT) added to radiotherapy (RT) in different risk groups of patients with early‐stage extranodal nasal‐type NK/T‐cell lymphoma (ENKTCL), and to investigate the risk of postponing RT based on induction CT responses. A total of 1360 patients who received RT with or without new‐regimen CT from 20 institutions were retrospectively reviewed. The patients had received RT alone, RT followed by CT (RT + CT), or CT followed by RT (CT + RT). The patients were stratified into different risk groups using the nomogram‐revised risk index (NRI). A comparative study was performed using propensity score‐matched (PSM) analysis. Adding new‐regimen CT to RT (vs RT alone) significantly improved overall survival (OS, 73.2% vs 60.9%, P < .001) and progression‐free survival (PFS, 63.5% vs 54.2%, P < .001) for intermediate‐risk/high‐risk patients, but not for low‐risk patients. For intermediate‐risk/high‐risk patients, RT + CT and CT + RT resulted in non‐significantly different OS (77.7% vs 72.4%; P = .290) and PFS (67.1% vs 63.1%; P = .592). For patients with complete response (CR) after induction CT, initiation of RT within or beyond three cycles of CT resulted in similar OS (78.2% vs 81.7%, P = .915) and PFS (68.2% vs 69.9%, P = .519). For patients without CR, early RT resulted in better PFS (63.4% vs 47.6%, P = .019) than late RT. Risk‐based, response‐adapted therapy involving early RT combined with CT is a viable, effective strategy for intermediate‐risk/high‐risk early‐stage patients with ENKTCL in the modern treatment era.

Qi, Shu‐Nan↗