Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Angular Reference”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18

Experimental investigation of the subsonic high-altitude operation of the NASA Lewis 10- by 10-foot supersonic wind tunnel

An experimental investigation was conducted in the NASA Lewis 10- by 10-Foot Supersonic Wind Tunnel during subsonic tunnel operation in the aerodynamic cycle to determine the test section flow characteristics near the Advanced Turboprop Project propeller model plane of rotation. The investigation used an eight-probe pitot static flow survey rake to measure total and static pressures at two locations in the wind tunnel: the test section and the bellmouth section (upstream of the two-dimensional flexible-wall nozzle). A cone angularity probe was used to measure any flow angularity in the test section. The evaluation was conducted at tunnel Mach numbers from 0.10 to 0.35 and at three operating altitudes from 2,000 to 50,000 ft. which correspond to tunnel reference total pressures from 1960 to 245 psfa, respectively. The results of this experimental investigation indicate a total-pressure loss area in the center of the test section and a static-pressure gradient from the test section centerline to the wall. These total and static pressure differences were observed at all tunnel operating altitudes and diminished at lower tunnel velocities. The total-pressure loss area was also found in the bellmouth section, which indicates that the loss mechanism is not the tunnel flexible-wall nozzle. The flow in the test section is essentially axial since very small flow angles were measured. The results also indicate that a correction to the tunnel total and static pressures must be applied in order to determine accurate freestream conditions at the test section centerline.

Hughes, Christopher E.↗

Improved Spectral and Angular Characterization of Libya-4 and Dome-C for consistent MODIS and VIIRS Radiometric Scaling

The NASA CERES observed SW and LW fluxes are utilized by the climate community for monitoring the Earth’s energy imbalance and for climate model validation. To facilitate seamless flux and cloud properties across MODIS, VIIRS, and geostationary (GEO) imagers the CERES project intercalibrates the imagers directly comparing the coincident ray-matched analogous channel radiances. For CERES edition 4 products, the MODIS, VIIRS and GEO imagers were radiometrically scaled to the Aqua-MODIS C5 calibration reference. There are no direct comparison opportunities between NPP and NOAA20 VIIRS, since they are positioned a half an orbit apart. The previous usage of Aqua-MODIS as a transfer radiometer is coming to an end, since the Aqua orbit is slowly drifting towards the terminator and will be deorbited in 2026. The CERES project will utilize the Libya-4 and Dome-C invariant targets to radiometrically scale between MODIS and VIIRS reflective solar bands. The Libya-4 and Dome-C Earth invariant targets will be characterized by the repeat cycle angular configuration. The target spectral band adjustment factors (SBAF) will be derived using EMIT and DESIS hyper-spectral observations onboard the ISS and will be compared with the existing SCIAMACHY, GOME-2, and Hyperion SBAFs. The DESIS and EMIT SBAF approach can incorporate the future CLARREO CPF SI traceable hyper-spectral measurements allowing the targets to be referenced to an absolute calibration reference. Utilizing the BRDF and atmospheric corrected characterization of one sensor with another will provide the scaling factors. Consistent scaling factors between the two invariant target validates the method.

David R. Doelling↗

SU-E-T-234: Daily Quality Assurance for a Six Degrees of Freedom Couch Using a Novel Phantom

Purpose: To test the accuracy and reproducibility of both translational and rotational movements for a couch with six degrees of freedom (6DoF) using a novel phantom design Methods: An end-to-end test was carried out using two different phantoms. A 6 cm3 cube with a central fiducial BB (WL-QA Sun Nuclear) and a custom fabricated rectangular prism (31 cm x 8 cm x 8 cm), placed on a baseplate with known angular offsets for pitch, roll and yaw with a central fiducial BB and unique surface structures for registration purposes, were used. The end-to-end test included an initial CT simulation for a reference study, setup to an offset mark on each phantom, registration of the reference CT to the acquired cone-beam CT, and final Winston-Lutz delivery at four cardinal gantry angles. Results for both translational and rotational movements were recorded and compared for both phantoms. Results: Translational and rotational measurements were performed with a PerfectPitch (Varian) couch for 10 trials for both phantoms. Distinct translational shifts were [−5.372±0.384mm, −10.183±0.137mm, 14.028±0.155mm] for the cube and [7.520±0.159mm, −9.117±0.101mm, 16.273±0.115mm] for the prototype phantom for lateral, longitudinal, and vertical shifts, respectively. Distinct rotational adjustments were [1.121±0.102o, −1.067±0.235o, −2.662±0.380o] for the cube and [2.534±0.059o, 1.994±0.025o, 2.094±0.076o] for the prototype for pitch, roll, and yaw, respectively. Winston-Lutz test results performed after 6DoF couch correction from each cardinal gantry angle ranged from 0.26–0.72mm for the cube and 0.55–0.86mm for the prototype. Conclusion: The prototype phantom is more precise for both translational and rotational adjustments compared to a commercial phantom. The design of the prototype phantom allows for a more discernible visual confirmation of correct translational and rotational adjustments with the prototype phantom. Winston-Lutz results are more accurate for the commercial phantom but are still within tolerance for the prototype phantom.

60 APPLIED LIFE SCIENCES↗

Fabrication and Study of a Concave Crystal Mirror for the KORTES Project

A method for fabrication of a concave spherical mirror made of crystalline quartz is proposed and X-ray optical properties of the mirror are studied. The radius of curvature is 1630 mm. The shape of the mirror surface is studied using an interferometer with a diffraction reference wave. In the entire processing region, the maximum deviation from the nearest sphere is about 0.2 μm and the rms is 34 nm, so that high quality of imaging is provided with an angular error of about 2″ (angular seconds). Reflection coefficient (about 7%) and lower bound limit of spectral selectivity (λ/δλ ≈ 1775) are determined in the vicinity of a wavelength of λ = 0.834 nm, which is close to the working wavelengths of the MgXII doublet (λ = 0.8418 and 0.8423 nm). Position of the Bragg peak and spectral selectivity remain unchanged upon bending of the crystal mirror within measurement accuracy.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

U.S. Department of Energy Reference Model Program RM1: Experimental Results

The Reference Model Project (RMP), sponsored by the U.S. Department of Energy’s (DOE) Wind and Water Power Technologies Program within the Office of Energy Efficiency & Renewable Energy (EERE), aims at expediting industry growth and efficiency by providing non-proprietary Reference Models (RM) of MHK technology designs as study objects for open-source research and development (Neary et al. 2014a,b). As part of this program, MHK turbine models were tested in a large open channel facility at the University of Minnesota’s St. Anthony Falls Laboratory (UMN-SAFL). Reference Model 1 (RM2) is a 1:40 geometric scale dual-rotor axial flow horizontal axis device with counter-rotating rotors, each with a rotor diameter d T = 0.5m. Precise blade angular position and torque measurements were synchronized with three acoustic Doppler velocimeters (ADVs) aligned with each rotor and the midpoint for RM1. Flow conditions for each case were controlled such that depth, h = 1m, and volumetric flow rate, Q w = 2.425m3s -1 , resulting in a hub height velocity of approximately U hub = 1.05ms -1 and blade chord length Reynolds numbers of R ec ≈ 3.0x105. Vertical velocity profiles collected in the wake of each device from 1 to 10 rotor diameters are used to estimate the velocity recovery and turbulent characteristics in the wake, as well as the interaction of the counter-rotating rotor wakes. The development of this high resolution laboratory investigation provides a robust dataset that enables assessing turbulence performance models and their ability to accurately predict device performance metrics, including computational fluid dynamics (CFD) models that can be used to predict turbulent inflow environments, reproduce wake velocity deficit, recovery and higher order turbulent statistics, as well as device performance metrics.

16 TIDAL AND WAVE POWER↗

Detailed study of oxidation/wear mechanism in lox turbopump bearings

Wear of 440C angular contact ball bearings of the phase 2 high pressure oxygen turbopump (HPOTP) of the space shuttle main engine (SSME) has been studied by means of various advanced nondestructive techniques (NDT) and modeled with reference to all known material, design, and operation variables. Three modes dominating the wear scenario were found to be the adhesive/sheer peeling (ASP), oxidation, and abrasion. Bearing wear was modeled in terms of the three modes. Lacking a comprehensive theory of rolling contact wear to date, each mode is modeled after well-established theories of sliding wear, while sliding velocity and distance are related to microsliding in ball-to-ring contacts. Microsliding, stress, temperature, and other contact variables are evaluated with analytical software packages of SHABERTH(TM)/SINDA(TM) and ADORE(TM). Empirical constants for the models are derived from NIST experiments by applying the models to the NIST wear data. The bearing wear model so established precisely predicts quite well the average ball wear rate for the HPOTP bearings. The wear rate has been statistically determined for the entire population of flight and development bearings based on Rocketdyne records to date. Numerous illustrations are given.

Chase, T. J.↗

RCC Plug Repair Thermal Tools for Shuttle Mission Support

A thermal math model for the Space Shuttle Reinforced Carbon-Carbon (RCC) Plug Repair was developed to increase the confidence in the repair entry performance and provide a real-time mission support tool. The thermal response of the plug cover plate, local RCC, and metallic attach hardware can be assessed with this model for any location on the wing leading edge. The geometry and spatial location of the thermal mesh also matches the structural mesh which allows for the direct mapping of temperature loads and computation of the thermoelastic stresses. The thermal model was correlated to a full scale plug repair radiant test. To utilize the thermal model for flight analyses, accurate predictions of protuberance heating were required. Wind tunnel testing was performed at CUBRC to characterize the heat flux in both the radial and angular directions. Due to the complexity of the implementation of the protuberance heating, an intermediate program was developed to output the heating per nodal location for all OML surfaces in SINDA format. Three Design Reference Cases (DRC) were evaluated with the correlated plug thermal math model to bound the environments which the plug repair would potentially be used.

Rodriguez, Alvaro C.↗

The STIS CCD Spectroscopic Line Spread Functions

We characterize the spectroscopic line spread functions of the spectroscopic CCD modes for high contrast objects. Our long range goal is to develop tools that accurately extract spectroscopic information of faint, point or extended sources in the vicinity of bright, point sources at separations approaching the realizable angular limits of HST with STIS. Diffracted and scattered light due to the HST optics, and scattered light effects within the STIS are addressed. Filter fringing, CCD fringing, window reflections, and scattering within the detector and other effects are noted. We have obtained spectra of several reference stars, used for flux calibration or for coronagraphic standards, that have spectral distributions ranging from very red to very blue. Spectra of each star were recorded with the star in the aperture and with the star blocked by either the F1 or F2 fiducial. Plots of the detected starlight along the spatial axis of the aperture are provided for four stars. With the star in the aperture, the line spread function is quite noticeable. Placing the star behind one of the fiducials cuts the scattered light and the diffracted light, is detectable even out to 1OOOOA. When the star is placed behind either fiducial, the scattered and diffracted light components, at three arcseconds displacement from the star, are below lop6 the peak of the star at wavelengths below 6000A; at the same angular distance, scattered light does contaminate the background longward of 6000A up to a level of 10(exp -5).

Gull, T.↗

Exchange of Alpha Particle in the {sup 16}O+{sup 12}C Elastic Scattering

We have analyzed twenty elastic scattering angular distributions of the {sup 16}O+{sup 12}C system, measured at Sao Paulo Pelletron Laboratory and also data from the literature. The energies cover the region around and above Coulomb barrier, ranging from 8.54 up to 75.43 MeV in the center of mass reference frame. In the {sup 16}O+{sup 12}C scattering, two different processes can occur which result in same exit channel, the elastic scattering and the exchange of an alpha particle between projectile and target. We have used the Optical Model formalism for the elastic scattering and the DWBA to describe the alpha transfer reaction contribution. Thus, by analyzing the {sup 16}O+C elastic scattering at backward angles we have obtained the {sup 16}O{sub gs} alpha spectroscopic factor.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Ultra-Low Noise Laser and Optical Frequency Comb-Based Timing System for the Event Horizon Explorer (EHE) Mission

Very Long Baseline Interferometry (VLBI) requires a highly stable time reference and synchronization system to maintain coherence between observations recorded independently at multiple stations – for example, the array of ground-based radio telescopes that comprise the Event Horizon Telescope (EHT). Instability in the time reference or inaccuracy in the synchronization impacts phase conference and reduces the performance of the VLBI system. For space-based telescopes like the Event Horizon Explorer (EHE) mission, the precision timing system must meet the size, weight, and power (SWaP) constraints of the spacecraft platform and be capable of operating in the space environment. The EHE mission is a proposed extension to the EHT that can improve the angular and time resolution of observations by enabling longer interferometric baselines than are possible on the Earth and sampling a wide range of Fourier spatial frequencies throughout the orbital motion. In this effort, we demonstrate the performance of one option for the EHE mission: the use of a space-qualified, ultra-low noise laser developed as part of the Laser Interferometer Space Antenna (LISA) mission as the timing reference, and an optical frequency comb to transfer the stability of this laser to the microwave regime for instrumentation use. We describe the implementation of the microwave down-conversion, in which the LISA cavity-stabilized laser is locked to a self-referenced optical frequency comb to divide the optical frequency down to 100 MHz. The phase noise of the 100 MHz signal is measured and validated using a phase noise analyzer that is referenced to a separate laboratory ultra-stable laser system. We present the results of this experiment, which demonstrates that the performance of this system meets the EHE requirement: a relative frequency error of 1e-14 from 1 to 30 seconds.

Hannah Tomio↗

Inclusive angular distribution of alpha and Li fragments produced in the Fe-C and Fe-Pb collisions at 1.88 GeV/u

The LS (laboratory system) emission angles theta for 2188 and 298 Li fragments, produced inclusively in relativistic Fe-C and Fe-Pb collisions, have been measured in reference to incident Fe-ion beam tracks nearby in nuclear emulsion. An empirical differential frequency formula, dN(cot theta) = exp (a + b cot theta)d(cot theta) is obtained with the constant b approx. = -0.026 at 1.88 GeV/u, which seems to be independent on the kinds of target nucleus as well as on the kinds of projectile fragments.

Kim, C. O.↗

The Lattice Boltzmann Method applied to neutron transport

In this paper the applicability of the Lattice Boltzmann Method to neutron transport is investigated. One of the main features of the Lattice Boltzmann method is the simultaneous discretization of the phase space of the problem, whereby particles are restricted to move on a lattice. An iterative solution of the operator form of the neutron transport equation is presented here, with the first collision source as the starting point of the iteration scheme. A full description of the discretization scheme is given, along with the quadrature set used for the angular discretization. An angular refinement scheme is introduced to increase the angular coverage of the problem phase space and to mitigate lattice ray effects. The method is applied to a model problem to investigate its applicability to neutron transport and the results are compared to a reference solution calculated, using MCNP. (authors)

97 MATHEMATICS AND COMPUTING↗

Interaction of 18-keV O{sup -} ions with Al{sub 2}O{sub 3} nanocapillaries

The transmission of 18-keV O{sup -} ions through Al{sub 2}O{sub 3} nanocapillaries with 50 nm in diameter and 12 {mu}m in length is studied in this work. By measuring angular distribution of transmitted particles when capillaries were tilted with respect to incident ion beam, two peaks were observed. It is distinguished that one of them is composed by direct transmitted ions and another one is composed by scattered ions. A phenomenon referred to as guiding effect, as found for highly charged ions and low-energy electrons, was observed. When negative ions (18-keV O{sup -}) are transmitted through nanocapillaries, most of them were ionized to neutral atoms and even positive ions. The intensity of transmitted particles (O{sup -}, O{sup 0}, and O{sup +}) decreased when the tilt angle increased. In transmitted particles, the fraction of O{sup -} declined but that of O{sup 0} and O{sup +} ions grew when the tilt angle grew. Both elastic collision and electrostatic scattering were found in scattered ions.

74 ATOMIC AND MOLECULAR PHYSICS↗

Visualization of fast ion phase-space flow in plasmas well-below, near and well-above Alfvén eigenmode stability threshold in tokamak

Abstract Transport of fast ions along certain local phase space paths, referred to as fast ion phase-space flow, has been systematically measured by an imaging neutral particle analyzer (INPA) in three plasma regimes, which are well-below, near, and well-above the Alfvén eigenmode stability threshold (Du et al 2021 Phys. Rev. Lett. 127 235002). (1) In plasmas well-below the Alfvén eignenmodes (AE) stability threshold, fast ions are well-confined on passing particle orbits without noticeable transport over the phase space. The observed INPA images agree well with the synthetic INPA images, using the fast ion distribution predicted by neoclassical theory. (2) In plasmas near the AE stability threshold, INPA images in the presence of AE activity moderately deviate from those without AE activity. The image difference can be well interpreted by AE-driven, phase-space fast ion flow. Paths of this flow over the velocity space (or streamlines) are reconstructed by the intersection lines of curved E ʹ and µ surfaces, referred to as E ʹ and µ line (where E ′ ≡ E − ( ω / n ) P ζ ; E , P ζ and µ are the energy, canonical toroidal momentum and magnetic moment of ions; ω and n are the angular frequency and toroidal mode number of AEs, respectively). Resonant fast ions move radially inward by gaining energy and move radially outward by losing energy and the trajectory well aligns with the E ʹ and µ lines that pass through the mode resonances near the injection energy of neutral beams. (3) In plasmas well-above the AE stability threshold, fast ion phase-space dynamics shows additional features. Fast ions are transported out of the birth positions so promptly along the streamlines that the slowing-down process from the injection energy is not observable, exhibiting strong critical gradient behavior at local phase space. As a result, the increase of electron temperature is very small, in spite of an increase of beam power by ∼ 45 % . It should be emphasized that the directions of phase-space transport, induced by AEs with different frequencies, structures and mode numbers, do not largely differ.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Transfer of autocollimator calibration for use with scanning gantry profilometers for accurate determination of surface slope and curvature of state-of-the-art x-ray mirrors

X-ray optics, desired for beamlines at free-electron-laser and diffraction-limited-storage-ring x-ray light sources, must have almost perfect surfaces, capable of delivering light to experiments without significant degradation of brightness and coherence. To accurately characterize such optics at an optical metrology lab, two basic types of surface slope profilometers are used: The long trace profilers (LTPs) and nanometer optical measuring (NOM) like angular deflectometers, based on electronic autocollimator (AC) ELCOMAT-3000. The inherent systematic errors of the instrument's optical sensors set the principle limit to their measuring performance. Where autocollimator of a NOM-like profiler may be calibrated at a unique dedicated facility, this is for a particular configuration of distance, aperture size, and angular range that does not always match the exact use in a scanning measurement with the profiler. Here we discuss the developed methodology, experimental set-up, and numerical methods of transferring the calibration of one reference AC to the scanning AC of the Optical Surface Measuring System (OSMS), recently brought to operation at the ALS Xray Optics Laboratory. We show that precision calibration of the OSMS performed in three steps, allows us to provide high confidence and accuracy low-spatial-frequency metrology and not â€print into' measurements the inherent systematic error of tool in use. Here, with the examples of the OSMS measurements with a state-of-The-Art x-ray aspherical mirror, available from one of the most advanced vendors of X-ray optics, we demonstrate the high efficacy of the developed calibration procedure. The results of our work are important for obtaining high reliability data, needed for sophisticated numerical simulations of beamline performance and optimization of beamline usage of the optics. This work was supported by the U. S. Department of Energy under contract number DE-AC02-05CH11231.

47 OTHER INSTRUMENTATION↗

Reflective all-sky thermal infrared cloud imager

A reflective all-sky imaging system has been built using a long-wave infrared microbolometer camera and a reflective metal sphere. This compact system was developed for measuring spatial and temporal patterns of clouds and their optical depth in support of applications including Earth-space optical communications. The camera is mounted to the side of the reflective sphere to leave the zenith sky unobstructed. The resulting geometric distortion is removed through an angular map derived from a combination of checkerboard-target imaging, geometric ray tracing, and sun-location-based alignment. A tape of high-emissivity material on the side of the reflector acts as a reference that is used to estimate and remove thermal emission from the metal sphere. In conclusion, once a bias that is under continuing study was removed, sky radiance measurements from the all-sky imager in the 8-14 μm wavelength range agreed to within 0.91 W/(m 2 sr) of measurements from a previously calibrated, lens-based infrared cloud imager over its 110° field of view.

47 OTHER INSTRUMENTATION↗

Redshift differences of galaxies in nearby groups

It is reported that galaxies in nearby groups exhibit anomalous nonvelocity redshifts. In this discussion, (1) four classes of nearby groups of galacies are analyzed, and no significant nonvelocity redshift effect is found; and (2) it is pointed out that transverse velocities (i.e., velocities transverse to the line of sight of the main galaxy, or center of mass) contribute components to the redshift measurements of companion galaxies. The redshifts of galaxies in nearby groups of appreciable angular size are considerably affected by these velocity projection effects. The transverse velocity contributions average out in rich, isotropic groups, and also in large samples of irregular groups of low membership, as in the four classes referred to in (1), but can introduce apparent discrepancies in small samples (as studied by Arp) of nearby groups of low membership.

Harrison, E. R.↗

Magnetic optical activity in intense laser fields. I - Self-rotation and Verdet constant

The paper is concerned with the Faraday rotation and circular dichroism of dilute gases in longitudinal magnetic fields subject to strong radiation fields. In particular, magnetic fields are considered which produce Zeeman shifts much smaller than inverse collision times but which may be greater or smaller then the multipole relaxation times. Doppler broadening is considered, and explicit expressions are given for dipole transitions in a two-level system with arbitrary angular momentum for strong and weak magnetic fields. The same system is then studied as a function of the external magnetic-field strength with a fixed laser frequency. It is shown that this experimental arrangement, referred to as forward scattering, has certain advantages that are not present in the more usual magnetic rotation spectroscopy.

Giraud-Cotton, S.↗