Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “AUTOCLAVES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18

Influence of hydride precipitation on the corrosion kinetics of Zircaloy-4: effect of the nano-structure and grain boundary properties of the zirconium oxide layer on oxygen diffusion flux - 2016-0073

Hydride precipitation at the oxide-metal interface is frequently proposed as causing the corrosion acceleration of Zircaloy-4 at high burnup in pressurized water reactors (PWRs). In order to identify the local mechanisms possibly involved, we studied the nano-structure of oxides formed on massive zirconium hydrides and reference Zircaloy-4 with an innovative grain mapping technique with the use of transmission electron microscopy (TEM). In autoclave PWR-conditions, the presence of a precipitated hydride phase, previously formed by a cathodic charging technique at the surface of Zircaloy-4, clearly increased the corrosion rate, and a higher oxygen diffusion flux along oxide grain boundaries is observed compared with the reference Zircaloy-4. The texture, grain size, and adjacent grain misorientation in the oxide layer were studied in detail along the direction of the oxide growth using an automated crystal orientation mapping technique associated with TEM for both pre-hydrided and reference Zircaloy-4 samples. The texture in the growth direction is similar on pre-hydrided and reference samples, but the grain-to-grain mis-orientations showed differences. Indeed, on the pre-hydrided sample, the misorientation of 90 deg. C with respect to the [001] monoclinic axis is less probable than in the reference oxide, and more mis-orientations of 50-70 deg. C and 120-150 deg. C, corresponding to larger mismatches between neighboring grain boundaries, are observed. A smaller average diameter of the columnar monoclinic grains is also clearly revealed for the oxide grown on the pre-hydrided sample that leads to a larger number of diffusion paths for oxidizing species. These results are discussed and used for simulating oxygen diffusion flux through the polycrystalline microstructure of the oxide layer as a function of the grain size. (authors)

36 MATERIALS SCIENCE↗

Optimizing chemistry for designing oxidation resistant FeCrAl alloys

Abstract Traditionally, FeCrAl alloys played an important role in high-temperature applications due to their ability to form a passive Al oxide film at temperatures above ~ 800 °C. Recently, FeCrAl alloys became of interest for the application of accident tolerant nuclear fuel cladding. This study covers work done at GE Research for better understanding the role of Al, Cr, and Mo in oxidation kinetics and thermodynamics. Several models and commercial prototype alloys have been tested in hydrothermal corrosion autoclave loops, at low temperature steam exposure (~ 400 °C), high temperature steam exposure (~ 1000 °C or higher), and high temperature air exposures. The results provide insights on how chromium and aluminum play a significant role in both high temperature and low temperature oxidation of FeCrAl. Additionally, machine learning tools are used to gain further insights on both predicting future optimized chemistries for balancing the properties of hydrothermal corrosion, low and high temperature steam oxidation, and thermal aging (which is exacerbated due to radiation in a nuclear reactor environment). GE plans to use this framework to further optimize the FeCrAl alloy system for use in nuclear reactor environments. Graphical abstract

Roy, Indranil (ORCID:0000000336124323)↗

Remote Monitoring of the Structural Health of Hydrokinetic Composite Turbine Blades (Final Report)

A health monitoring approach is investigated for hydrokinetic turbine blade applications. In-service monitoring is critical due to the difficult environment for blade inspection and the cost of inspection downtime. Composite blade designs have advantages that include long life in marine environments and great control over mechanical properties. Experimental strain characteristics are determined for static loads and free-vibration loads. These experiments are designed to simulate the dynamic characteristics of hydrokinetic turbine blades. Carbon/epoxy symmetric composite laminates are manufactured using an autoclave process. Four-layer composite beams, eight-layer composite beams, and two-dimensional eight-layer composite blades are instrumented for strain. Experimental results for strain measurements from electrical resistance gages are validated with theoretical characteristics obtained from in-house finite-element analysis for all sample cases. These preliminary tests on the composite samples show good correlation between experimental and finite-element strain results. A health monitoring system is proposed in which damage to a composite structure, e.g. delamination and fiber breakage, causes changes in the strain signature behavior. The system is based on embedded strain sensors and embedded motes in which strain information is demodulated for wireless transmission. In-service monitoring is critical due to the difficult environment for blade inspection and the cost of inspection downtime. Composite blade designs provide a medium for embedding sensors into the blades for in-situ health monitoring. The major challenge with in-situ health monitoring is transmission of sensor signals from the remote rotating reference frame of the blade to the system monitoring station. In the presented work, a novel system for relaying in-situ blade health measurements in hydrokinetic systems is described and demonstrated. An ultrasonic communication system is used to transmit sensor data underwater from the rotating frame of the blade to a fixed relay station. Data are then broadcast via radio waves to a remote monitoring station. Results indicate that the assembled system can transmit simulated sensor data with an accuracy of ±5% at a maximum sampling rate of 500 samples/sec. A power investigation of the transmitter within the blade shows that continuous max-sampling operation is only possible for short durations (~days), and is limited due to the capacity of the battery power source. However, intermittent sampling, with long periods between samples, allows for the system to last for very long durations (~years). Finally, because the data transmission system can operate at a high sampling rate for short durations or at a lower sampling rate/higher duty cycle for long durations, it is well-suited for short-term prototype and environmental testing, as well as long-term commercially-deployed hydrokinetic machines.

13 HYDRO ENERGY↗

Energy Saving Glass Lamination via Selective Radio-Frequency Heating

This Inventions and Innovations program supported the technical and commercial research and development needed to elevate Ceralink's energy saving process for flat glass lamination from bench scale to a self-supporting technology with significant potential for growth. Radio-frequency heating was any un-explored option for laminating glass prior to this program. With significant commercial success through time and energy savings in the wood, paper, and plastics industries, RF heating was found to have significant promise for the energy intensive glass lamination industry. A major technical goal of the program was to demonstrate RF lamination across a wide range of laminate sizes and materials. This was successfully accomplished, dispelling many skeptics' concerns about the abilities of the technology. Ceralink laminated panels up to 2 ft x 3 ft, with four sets processed simultaneously, in a 3 minute cycle. All major categories of interlayer materials were found to work with RF lamination. In addition to laminating glass, other materials including photovoltaic silicon solar cells, light emitting diodes, metallized glass, plastics (acrylic and polycarbonate), and ceramics (alumina) were found compatible with the RF process. This opens up a wide range of commercial opportunities beyond the initially targeted automotive industry. The dramatic energy savings reported for RF lamination at the bench scale were found to be maintained through the scale up of the process. Even at 2 ft x 3 ft panel sizes, energy savings are estimated to be at least 90% compared to autoclaving or vacuum lamination. With targeted promotion through conference presentations, press releases and internet presence, RF lamination has gained significant attention, drawing large audiences at American Ceramic Society meetings. The commercialization success of the project includes the establishment of a revenue-generating business model for providing process development and demonstrations for potential RF lamination users. A path to industrial energy benefits and revenue through industrial equipment sales was established in a partnership with Thermex Thermatron, a manufacturer of RF equipment.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

The Efficacy of Ultraviolet Radiation for Sterilizing Tools Used for Surgically Implanting Transmitters into Fish

Telemetry is frequently used to examine the behavior of fish, and the transmitters used are normally surgically implanted into the coelom of fish. Implantation requires the use of surgical tools such as scalpels, forceps, needle holders, and sutures. When several fish are implanted consecutively for large telemetry studies, it is common for surgical tools to be sterilized or, at minimum, disinfected between each use so that pathogens that may be present are not spread among fish. However, autoclaving tools can take a long period of time, and chemical sterilants or disinfectants can be harmful to both humans and fish and have varied effectiveness. Ultraviolet (UV) radiation is commonly used to disinfect water in aquaculture facilities. However, this technology has not been widely used to sterilize tools for surgical implantation of transmitters in fish. To determine its efficacy for this application, Pacific Northwest National Laboratory researchers used UV radiation to disinfect surgical tools (i.e., forceps, needle holder, stab scalpel, and suture) that were exposed to one of four aquatic organisms that typically lead to negative health issues for salmonids. These organisms included Aeromonas salmonicida, Flavobacterium psychrophilum, Renibacterium salmoninarum, and Saprolegnia parasitica. Surgical tools were exposed to the bacteria by dipping them into a confluent suspension of three varying concentrations (i.e., low, medium, high). After exposure to the bacterial culture, tools were placed into a mobile Millipore UV sterilization apparatus. The tools were then exposed for three different time periods—2, 5, or 15 min. S. parasitica, a water mold, was tested using an agar plate method and forceps-pinch method. UV light exposures of 5 and 15 min were effective at killing all four organisms. UV light was also effective at killing Geobacillus stearothermophilus, the organism used as a biological indicator to verify effectiveness of steam sterilizers. These techniques appear to provide a quick alternative disinfection technique for some surgical tools that is less harmful to both humans and fish while not producing chemical waste. However, we do not recommend using these methods with tools that have overlapping parts or other structures that cannot be directly exposed to UV light such as needle holders.

Walker, Ricardo W.↗

Samuel P. Massie Chair of Excellence In Environmental Disciplines: Hampton University 1994-2010 Year Report

The establishment of the DOE-EM Dr. Samuel P. Massie Chair of Excellence provides an excellent opportunity for Hampton University to be involved in key environmental issues in the 21 st Century. The main areas of focus are on: 1. Coal gasification with respect to pollution prevention and reduction. 2. Solid waste treatment through bioremediation technology and 3. Industrial wastewater treatment Synthesizing ion catalysts suitable for use in slurry bubble column reaction was carried out. Construction of an autoclave continuous stirred tank reactor has been completed. At the initial stage of the development of this program, work was conducted in the area of formic acid recovery from waste streams, which yielded useful results. We also succeeded in the removal of priority metal ions such as cadmium, chromium, copper, lead, mercury, nickel, silver, thallium, zinc, etc., from industrial and municipal wastewater by using natural wastes. The process uses tree leaves to adsorb the metal ions in the wastewater. The ultimate goal is to develop inexpensive, highly available, effective metal ion adsorbents from natural wastes as an alternative to existing commercial adsorbents, and also to explain the possible adsorption mechanism that is taking place. This technology uses natural wastes to eliminate other wastes. Obviously, there are several advantages: (1) the negative impact on environment is eliminated, (2) the complicated regeneration step is not needed, and (3) the procedure saves money and energy. Twelve different types of leaves have been tested with lead, zinc, and nickel. The study mechanism showed that the leaf tannin is an active ingredient in the adsorption of metal ions. The ion-exchange mechanism controlled the adsorption process.

42 ENGINEERING↗

Evaluation of Aluminum-Boron Carbide Neutron Absorbing Materials for Interim Storage of Used Nuclear Fuel

The objective of this work was to understand the corrosion behavior of Boral® and Bortec® neutron absorbers over long-term deployment in a used nuclear fuel dry cask storage environment. Corrosion effects were accelerated by flowing humidified argon through an autoclave at temperatures up to 570°C. Test results show little corrosion of the aluminum matrix but that boron is leaching out of the samples. Initial tests performed at 400 and 570°C were hampered by reduced flow caused by the rapid build-up of solid deposits in the outlet lines. Analysis of the deposits by XRD shows that the deposits are comprised of boron trioxide and sassolite (H 3 BO 3 ). The collection of boron- containing compounds in the outlet lines indicated that boron was being released from the samples. Observation of the exposed samples using SEM and optical microscopy show the growth of new phases in the samples. These phases were most prominent in Bortec® samples exposed at 570°C. Samples of Boral® exposed at 570°C showed minimal new phase formation but showed nearly the complete loss of boron carbide particles. Boron carbide loss was also significant in Boral samples at 400°C. However, at 400°C phases similar to those found in Bortec® were observed. The rapid loss of the boron carbide particles in the Boral® is suspected to inhibit the formation of the new secondary phases. However, Material samples in an actual dry cask environment would be exposed to temperatures closer to 300°C and less water than the lowest test. The results from this study conclude that at the temperature and humidity levels present in a dry cask environment, corrosion and boron leaching will have no effect on the performance of Boral® and Bortec® to maintain criticality control.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Corrosion report for the U-Mo fuel concept

The Fuel Cycle Research and Development (FCRD) program of the Office of Nuclear Energy (NE) has implemented a program to develop a Uranium-Molybdenum (U-Mo) metal fuel for Light Water Reactors (LWR)s. Uranium-Molybdenum fuel has the potential to provide superior performance based on its thermo-physical properties, which includes high thermal conductivity for less stored heat energy. With sufficient development, it may be able to provide the Light Water industry with a melt-resistant accident tolerant fuel with improved safety response. However, the corrosion of this fuel in reactor water environments needs to be further explored and optimized by additional alloying. The Pacific Northwest National Laboratory has been tasked with performing ex-reactor corrosion testing to characterize the performance of U-Mo fuel. This report documents the results of the effort to characterize and develop the U-Mo metal fuel concept for LWRs with regard to corrosion testing. The results of a simple screening test in buffered water at 30°C using surface alloyed U-10Mo is documented and discussed. The screening test was used to guide the selection of several potential alloy improvements that were found and are recommended for further testing in autoclaves to simulate PWR water conditions more closely.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Hydrogen Fracture Toughness Tester Completion

The Hydrogen Fracture Toughness Tester (HFTT) is a mechanical testing machine designed for conducting fracture mechanics tests on materials in high-pressure hydrogen gas. The tester is needed for evaluating the effects of hydrogen on the cracking properties of tritium reservoir materials. It consists of an Instron Model 8862 Electromechanical Test Frame; an Autoclave Engineering Pressure Vessel, an Electric Potential Drop Crack Length Measurement System, associated computer control and data acquisition systems, and a high-pressure hydrogen gas manifold and handling system.

36 MATERIALS SCIENCE↗

Fundamental Studies of the Role of Grain Boundaries on Uniform Corrosion of Advanced Nuclear Reactor Materials

The main objective of this proposal is to develop fundamental understanding of the role of grain boundaries in stable oxide growth. To understand the process of oxide layer destabilization, it is necessary to observe the early stages of corrosion. During conventional studies in which a sample is exposed and examined after removal from the autoclave, the destabilization process will normally have already taken place, and is only examined post facto. To capture the instants of oxide destabilization, it is necessary to observe it in situ; however, significant questions always arise as to the influence of the corrosion geometry and conditions on the corrosion process. Thus, a combination of post facto examinations and in situ studies is proposed, which also combines state-of-the-art characterization techniques to derive a complete understanding of the destabilization process and the role of grain boundaries.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Molybdenum Disilicide Oxidation Kinetics in High Temperature Steam

The Fuel Cycle Research and Development program’s Advanced Fuels Campaign is currently supporting a range of experimental efforts aimed at the development and qualification of ‘accident tolerant’ nuclear fuel forms. One route to enhance the accident tolerance of nuclear fuel is to replace the zirconium alloy cladding, which is prone to rapid oxidation in steam at elevated temperatures, with a more oxidation-resistant cladding. Several cladding replacement solutions have been envisaged. The cladding can be completely replaced with a more oxidation resistant alloy, a layered approach can be used to optimize the strength, creep resistance, and oxidation tolerance of various materials, or the existing zirconium alloy cladding can be coated with a more oxidation-resistant material. Molybdenum is one candidate cladding material favored due to its high temperature creep resistance. However, it performs poorly under autoclave testing and suffers degradation under high temperature steam oxidation exposure. Development of composite cladding architectures consisting of a molybdenum core shielded by a molybdenum disilicide (MoSi 2 ) coating is hypothesized to improve the performance of a Mo-based cladding system. MoSi 2 was identified based on its high temperature oxidation resistance in O 2 atmospheres (e.g. air and “wet air”). However, its behavior in H 2 O is less known. This report presents thermogravimetric analysis (TGA), scanning electron microscopy (SEM), and x-ray diffraction (XRD) results for MoSi 2 exposed to 670-1498 K water vapor. Synthetic air (80-20%, Ar-O 2 ) exposures were also performed, and those results are presented here for a comparative analysis. It was determined that MoSi 2 displays drastically different oxidation behavior in water vapor than in dry air. In the 670-1498 K temperature range, four distinct behaviors are observed. Parabolic oxidation is exhibited in only 670-773 K water vapor, a temperature range in which the material pests in dry O 2 environments. From 877-1084 K in water vapor, MoSi 2 undergoes rapid mass gain resulting in oxidation throughout the bulk of the sample at 980 K and 1084 K. The resulting material displays swelling and warping after the 980-1084 K exposures. A pre-passivation heat treatment performed at 1395 K was found capable of producing a coarse SiO 2 layer that limited pesting at lower temperatures in water vapor over the time periods investigated.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Corrosion of Structural Materials for Advanced Supercritical Carbon- Dioxide Brayton Cycle

The supercritical carbon-dioxide (referred to as SC-CO 2 hereon) Brayton cycle is being considered for power conversion systems for a number of nuclear reactor concepts, including the sodium fast reactor (SFR), fluoride saltcooled high temperature reactor (FHR), and high temperature gas reactor (HTGR), and several types of small modular reactors (SMR). The SC-CO 2 direct cycle gas fast reactor has also been recently proposed. The SC-CO 2 Brayton cycle (discussed in Chapter 1) provides higher efficiencies compared to the Rankine steam cycle due to less compression work stemming from higher SC-CO 2 densities, and allows for smaller components size, fewer components, and simpler cycle layout. For example, in the case of a SFR using a SC-CO 2 Brayton cycle instead of a steam cycle would also eliminate the possibility of sodium-water interactions. The SC-CO 2 cycle has a higher efficiency than the helium Brayton cycle, with the additional advantage of being able to operate at lower temperatures and higher pressures. In general, the SC-CO 2 Brayton cycle is well-suited for any type of nuclear reactor (including SMR) with core outlet temperature above ~ 500°C in either direct or indirect versions. In all the above applications, materials corrosion in high temperature SC-CO 2 is an important consideration, given their expected lifetimes of 20 years or longer. Our discussions with National Laboratories and private industry early on in this project indicated materials corrosion to be one of the significant gaps in the implementation of SC-CO 2 Brayton cycle. Corrosion can lead to a loss of effective load-bearing wall thickness of a component and can potentially lead to the generation of oxide particulate debris which can lead to three-body wear in turbomachinery components. Another environmental degradation effect that is rather unique to CO 2 environment is the possibility for simultaneous occurrence of carburization during oxidation of the material. Carburization can potentially lead to embrittlement of structural alloys in SC-CO 2 Brayton cycle. An important consideration in regards to corrosion is that the temperatures can vary widely across the various sections of the SC-CO 2 Brayton cycle, from room temperature to 750°C, with even higher temperatures being desirable for higher efficiencies. Thus the extent of corrosion and corrosion mechanisms in various components and SC-CO 2 Brayton cycle will be different, requiring a judicious selection of materials for different sections of the cycle. The goal of this project was to address materials corrosion-related challenges, identify appropriate materials, and advance the body of scientific knowledge in the area of high temperature SC-CO 2 corrosion. The focus was on corrosion of materials in SC-CO 2 environment in the temperature range of 450°C to 750°C at a pressure of 2900 psi for exposure duration for up to 1000 hours. The Table below lists the materials tested in the project. The materials were selected based on their high temperature strength, their code certification status, commercial availabilities, and their prior or current usage in the nuclear reactor industry. Additionally, pure Fe, Fe-12%Cr, and Ni-22%Cr were investigated as simple model materials to more clearly understand corrosion mechanisms. This first phase of the project involved testing in research grade SC-CO 2 (99.999% purity). Specially designed autoclaves with high fidelity temperature, pressure, and flow control capabilities were built or modified for this project.

36 MATERIALS SCIENCE↗

Evaluation of Additive Manufacturing for High Volume Composite Part Molds

ORNL worked with TruDesign, LLC to develop viable coating solutions to enable the use of large scale 3D printing for both low-temperature and high-temperature composite molds. This project resulted in two commercial products and successfully demonstrated the use of printed molds for autoclave processing for the first time.

42 ENGINEERING↗

SiC Composite for Fuel Structure Applications

Extensive evaluation was performed to determine the suitability of using SiC composite as a boiling water reactor (BWR) fuel channel material. A thin walled SiC composite box, 10 cm in dimension by approximately 1.5 mm wall thickness was fabricated using chemical vapor deposition (CVD) for testing. Mechanical test results and performance evaluations indicate the material could meet BWR channel mechanical design requirement. However, large mass loss of up to 21% was measured in in-pile corrosion test under BWR-like conditions in under 3 months of irradiation. A fresh sister sample irradiated in a follow-up cycle under PWR conditions showed no measureable weight loss and thus supports the hypothesis that the oxidizing condition of the BWR-like coolant chemistry was responsible for the high corrosion rate. A thermodynamic evaluation showed SiC is not stable and the material may oxidize to form SiO 2 and CO 2 . Silica has demonstrated stability in high temperature steam environment and form a protective oxide layer under severe accident conditions. However, it does not form a protective layer in water under normal BWR operational conditions due to its high solubility. Corrosion product stabilization by modifying the SiC CVD surface is an approach evaluated in this study to mitigate the high corrosion rate. Titanium and zirconium have been selected as stabilizing elements since both TiSiO 4 and ZrSiO 4 are insoluble in water. Corrosion test results in oxygenated water autoclave indicate TiSiO4 does not form a protective layer. However, zirconium doped test samples appear to form a stable continuous layer of ZrSiO 4 during the corrosion process. Additional process development is needed to produce a good ZrSiC coating to verify functionality of the mitigation concept.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Alkali-activated Class F Fly Ash-rich Portland Cement Blends as Alternative Thermal Shock Resistant Cements

This study focused on evaluating the resistance of 300°C-autocalved alkali-activing Class F fly ash (FAF)-rich Type II Ordinary Portland Cement (OPC) blends with 80/20 and 90/10 FAF/OPC ratios to five thermal-shock (TS) fatigue cycles (one cycle, 600°C heat – 25°C water quenching). The factors to be evaluated included the hydration behaviors, crystalline/ amorphous phaseidentifications, -compositions and -transformations, and microstructural-developments andalterations for blended cements assembled by three different alkaline activators, sodium metasilicate (SMS), soda ash (SA), and sodium sulfate (SS). All factors were related directory to the changes in compressive strength after TS testing. The setting time of cement slurries at 25° and 85°C depended on the alkaline activators; SMS and SA contributing to a strong alkalinity hastened setting, while SS with moderate alkalinity extended the setting time. A more prolonged setting time was observed from non-activated cement. In this case, there were two separated hydration reactions: The first reaction was the hydration of OPC; the second one was associated with the dissolution and pozzolanic activity of FAF. In contrast, all alkali- activated cements engendered the concomitant hydration of OPC and FAF, thereby conferring a higher compressive strength on them than that of the non-activator one. The principal contributor to the development of strength of both the non-activated and activated cements at 300°C was the amorphous NaO 2 - or CaO-Al 2 O 3 - SiO 2 -H 2 O (N,C-A-S-H) phase formed by the interactions between alkaline activator, OPC, and FAF. This phase played an important role in minimizing the loss in strength after TS. On the other hand, adding SMS and SA introduced the mixed crystalline FAF-OPC hydrates, such as garranite and wairakite, as the major phases, into the autoclaved cement bodies. Also, these activators induced the formation of two FAF-related crystalline hydrates, analcime as the major phase and riversidelite (0.9 nm tobermorite) as the minor one. However, these identified phases were sensitive to TS, so converting the major phases into minor phases or vanishment. In contrast, three crystalline phases including calcite and anhydrous sodium sulfate as the major ones and 1.1 nm tobermorite as the minor one, that formed in non-activated and activated cements remained unchanged after TS. Additionally, SAactivated cement revealed porous microstructure created by the incorporation of copious amount of carbonate reaction products into the cement, raising concerns that cements might enhance the rate of water transportation and reduce compressive strength. Nevertheless, TS-insensitive amorphous N,C-A-S-H phase as the major cementitions structure coexisting with TS-insensitive crystalline products were responsible for sustaining the integrity of alkali-activated FAF-rich OPC cement systems in such harsh heat-cooling fatigue environments.

15 GEOTHERMAL ENERGY↗

Ediesel: Diesel Additive production from ethanol and bio-diesel coproducts

This project has focused on supporting and expanding the U.S. ethanol industry by developing new conversion routes and products from ethanol and the byproducts made in ethanol fermentation. The work is relevant to the DOE program goals of developing high-margin chemical products in the biorefinery to economically support large-scale biofuel production. The higher alcohols from condensation of ethanol, alkylated amine compounds made by electrocatalytic alkyation, and fusel alcohols produced by modified fermentation microorganisms are all existing or potentially large-scale commodity or specialty chemicals with well-defined uses in industry. The formation of higher alcohols from ethanol in the condensed phase developed several catalysts, first in stirred batch autoclave reactors and then in a continuous flow reactor system, to achieve significant yields of n-butanol and higher alcohols. The best selectivity to higher alcohols exceeded 80% of theoretical at ethanol conversions of 30-40%. From the laboratory experiments and analysis of the phase equilibria of the species involved, a process concept was generated and simulated in AspenPlus to determine the specifications of the various equipment involved in the process. Results show that for the conversion and selectivity described above, the required n-butanol selling price of ~$1.60/kg is in the range of current n-butanol selling price in the marketplace. Several additional permutations of the process, along with evaluation of higher conversion and selectivities to desired alcohol products, showed that the production of n-butanol from ethanol should be competitive in the marketplace as the science and engineering behind the process improves with continued development. A second aspect of the project focused on producing fusel alcohols in increased quantities during ethanol fermentation. Fusel alcohols, which are composed primarily of isoamyl alcohol and minor quantities of C3-C6 alcohols, have potential as higher value feed stocks for specialty chemical production. Several strains of yeast were evaluated for fusel alcohol production, and the most efficient process for separating and purifying fusel alcohols was developed from both experiments and simulation. Finally, model fusel alcohol mixtures were subjected to condensation reactions with ethanol to prepare higher alcohols that again have potential for specialty chemical or solvent applications. In this preliminary work, measurable quantities of several species were observed, including some species that were previously unknown or uncharacterized in the literature. The third aspect of the project involved the electrocatalytic alkylation of amines with alcohols to form alkyl amines. Ethanol has been demonstrated to serve as an effective ethyl group transfer agent to the nitrogen centers of amines, a reaction with only water as a byproduct. Mild reaction conditions (60 °C, aqueous solution) are enabled by the novel use of simple, undivided electrochemical cell reactors that include long-lived, low cost catalytic electrodes. Direct polyalkylation of ammonia and isolation of the resulting triethylamine product was readily achieved in high yield. Though classical high temperature and pressure industrial scale alkylations reactions will likely continue to be used for production of simple product such as triethylamine, this approach has opened the door to the low cost, low waste use of ethanol and related primary and secondary alcohols to alkylate more delicate amines that were heretofore difficult to synthesize.

02 PETROLEUM↗

Additive Manufacturing Using Epoxy and Anhydride Curatives

ORNL worked with Dixie Chemical Company to develop epoxy material solutions with anhydride curatives printable on a large-scale printer. Rheological evaluation showed that the addition of high surface area fillers produced a stable yield-stress fluid that is capable of being used in extrusion deposition additive manufacturing. The resulting printed structures have the necessary mechanical and thermomechanical performance to be used in elevated temperature tooling for various composites processing, such as an autoclave.

36 MATERIALS SCIENCE↗

Hydrothermal Corrosion of Second Generation FeCrAl Alloys in Boiling Water Reactor Conditions

As part of an effort to develop advanced fuel cladding for use in light water reactors, several ORNL-developed FeCrAl alloys were tested in BWR conditions to determine their resistance to hydrothermal corrosion. Coupons with alloy compositions Fe-10Cr-6Al-2Mo, Fe-13Cr-5Al-2Mo, Fe-13Cr-6Al-2Mo, Fe-13Cr-7Al-2Mo, and Fe-13Cr-5Al-2Mo-1Nb were tested in BWR-NWC and BWR-HWC for 9 months in continuously refreshing autoclaves. Commercial APMT and Zircaloy-2 were also tested for comparison. Among samples exposed to HWC, Alloy C06M (10Cr-6Al) performed best, with a mass loss of 0.34 mg/cm 2 over 9 months, and C037M performed worst with a mass loss of 1.2 mg/cm 2 over 9 months. This mass loss was similar to Gen-1 FeCrAl alloys, and represents an estimated annual thickness loss of approximately a few µm per year. Samples exposed to NWC had very small mass losses of less than 0.15 mg/cm 2 or mass gains up to 0.05 mg/cm 2 . These represent very small annual losses in thickness. Based on the results of this testing, the Gen-2 FeCrAl alloys tested have suitable resistance to hydrothermal corrosion for use as fuel cladding in BWR-NWC and BWR-HWC conditions.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗