Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “working clean”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Accelerated Aging Humidity Chamber for Nuclear Grade HEPA Filter Media

A unique accelerated aging humidity chamber for simulating the natural aging process of nuclear grade high efficiency particulate air (HEPA) filter media is being designed, implemented, and tested. The nuclear industry currently lacks information regarding the shelf life and service life of HEPA filter media. The Department of Energy recommends disposing of HEPA filters 10 years after the manufacture date for filters operated under dry conditions. Studies have shown the tensile strength and water repellency of HEPA filter media diminish with age. The chamber's principal function is to sustain an elevated relative humidity condition for an extended duration specified by the Arrhenius aging model. To accomplish this, various design parameters were established: (1) consistently achieve uniform humidity conditions within the chamber to equally expose media sheets, (2) ensure the chamber is sufficiently sealed to mitigate the uncontrolled infiltration of air, (3) confidently secure the media sheets to avert the introduction of unnecessary stressing/creasing, (4) fabricate the chamber from clear polycarbonate material to allow inspection of the media sheets, (5) provide a safe and ergonomic design for personnel, (6) ensure the chamber design is replicable and relatively easy to fabricate/assemble. A humidity source, fan, PID controller, humidity and temperature transmitters, and data loggers are required for proper operation and control of the chamber. The humidity source must accommodate target values up to 95% relative humidity throughout the chamber. The three humidity and temperature transmitters are strategically spaced throughout the chamber to ensure uniform conditions. The 10 cubic feet per minute (CFM) fan selected intends to accomplish the desired air change rate inside the chamber of approximately 20 air changes per hour (ACH). The 2 plenums on the upper and lower portions of the chamber utilize a perforated design to uniformly distribute air, promote air mixing, and control the air velocity entering the chamber. Industrial blueprint hanging clamps are being retrofitted to be seated within the chamber drawers and firmly secure the nuclear grade filter media. The aged media will be evaluated using autopsy methodology, and the results obtained intend to help clarify the useful life of nuclear grade HEPA filters. Nuclear grade high efficiency particulate air (HEPA) filters are defined as disposable, extended-media, dry-type filters with a rigid casing enclosing the full depth of the pleats and have a minimum particle removal efficiency of 99.97%. [1] - HEPA filters are constantly exposed to stressors and subsequently have been shown to degrade as the filter ages. Properties such as tensile strength and water repellency, along with others, are negatively impacted. [2] - Due to the scarcity of naturally aged HEPA filters available, it is crucial to develop accelerated aging methods which effectively mimic the natural degradation effects. - After accelerated aging, the filters are subject to testing in the Axial Flow Large Scale Test Stand (ALSTS) and other analysis techniques such as the same qualification tests performed directly after being manufactured. - Quality data is necessary for future decisions regarding the lifetime of nuclear grade HEPA filters. - The objective is to develop a prototype accelerated aging humidity chamber for nuclear grade HEPA filter media. The chamber should expose the media to commonly occurring stressors to expedite the degradation process caused by aging. PID yields reliable and reproducible results: - CFD model correlates well with actual performance; - Further analysis is needed to complete characterization; - Future work for the chamber is still to be completed. The data shown in Figure 5 and Table 1 indicate the system is functioning as designed. As can be determined from the system response evaluation in Table 1, the PID controller is yielding reliable and reproducible results at each set point. As the set point increases, the time constant and 20% settling time increase accordingly. From the results in Table 1, it stands to reason that the CFD model correlates well with the actual performance of the system. Each system response parameter for the 90%RH* CFD model is slightly lower than the parameters collected from the physical model tested at an equivalent set point. This is to be expected considering the inlet in the CFD model is a constant supply of water vapor, whereas the physical model uses a PID controller to monitor the amount of water vapor needed and reacts accordingly. More analysis is still to be done on the prototype chamber. A pressure test will be conducted in order to determine the hourly leak rate of the chamber. This test will involve constant air flow into the chamber until the desired pressure is reached. A uniformity test will also be conducted in order to ensure each filter medium is being exposed to equivalent relative humidity levels. This test will involve an array of humidity meters strategically oriented inside the chamber to record any possible gradients. Future work for the chamber includes dehumidification abilities, tests while fully loaded with filters, and temperature control. Once completed, the autopsy team at Institute of Clean Energy Technology will conduct necessary accelerated aging studies as needed.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2025

Develop a Simulation Framework for Understanding Physico-Chemical Processes and Optimization of CHZ' Plastic Thermolyze Technology (CRADA Final Report)

Thermolyzer(TM) technology is a third-generation, multi-reactor, oxygen-free, low pressure, slow pyrolysis process. It has proven to be remarkably versatile in successfully processing all types of hydrocarbon waste. These include all seven types of plastics, tires, auto shredder residue, carpet, electronic waste, and composites. Working with the IACMI, Thermolyzer(TM) technology has recovered the glass and carbon fibers from wind turbine blades for reuse into new applications. Its primary output is a synthesis gas that is rich in H 2 , CH 4 , and small amounts of C 2-4 aliphatic hydrocarbons. Other components are CO and CO 2 . Three unique features set Thermolyzer(TM) apart from other pyrolysis systems: the syngas is clean enough to run in Siemens or Solar gas turbines or IC engines without fouling, clean, salable, byproducts are produced, and CO 2 emissions are lower than natural gas power plants. Research results have been obtained from an operating 7 ton/day facility. A 44 ton/day plant has successfully operated as noted above. The process works because it makes use of the recoverable embodied energy in the feedstock. Surprisingly, a pound of some plastics has the same recoverable energy content as a pound of gasoline. Thus, it is imperative to develop a process that economically converts scrap plastics (including ocean plastics) into energy and thereby conserve the non-renewable fossil fuels for future generations. The Thermolyzer(TM) technology can also be used to create liquid fuels like gasoline and diesel from hydrocarbon wastes. Because of the high hydrogen content of the synthesis gas, hydrogen can be recovered more inexpensively than the current solar or wind energy being used to electrolyze water. That hydrogen can be used for fuel cell powered vehicles or converted into ammonia for agriculture or as a hydrogen storage medium. Extension of this technology to other wastes such as tires, auto shredder residue or wood wastes would expand the circular economy.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Twisted van der Waals Josephson Junction Based on a High-T c Superconductor

Stacking two-dimensional van der Waals (vdW) materials rotated with respect to each other show versatility for studying exotic quantum phenomena. In particular, anisotropic layered materials have great potential for such twistronics applications, providing high tunability. In this work, we report anisotropic superconducting order parameters in twisted Bi 2 Sr 2 CaCu 2 O 8+x (Bi-2212) vdW junctions with an atomically clean vdW interface, achieved using the microcleave-and-stack technique. The vdW junctions with twist angles of 0° and 90° showed the maximum Josephson coupling, comparable to that of intrinsic Josephson junctions. As the twist angle approaches 45°, Josephson coupling is suppressed, and eventually disappears at 45°. The observed twist angle dependence of the Josephson coupling can be explained quantitatively by theoretical calculation with the d-wave superconducting order parameter of Bi-2212 and finite tunneling incoherence of the junction. Our results revealed the anisotropic nature of Bi-2212 and provided a novel fabrication technique for vdW-based twistronics platforms compatible with air-sensitive vdW materials.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2020

Effective Missing Value Imputation Methods for Building Monitoring Data

To understand behaviors of natural and man-made events, such as energy consumption of buildings, which accounts for 40% of energy uses in the US, we deploy automated monitoring devices to record periodic observations. However, such experimental and observation data often contains problems and irregularities that have to be cleaned up before analyses. Due to various conditions affecting sensor operations, the communication channels, recording steps, or the recording media, the recorded data might have missing values, errors, or anomalous values. An effective way to clean up these problems is to replace these missing values, errors and anomalous values with expected values, a process generally known as imputation. In this work, we survey commonly used missing value imputation techniques and compare their performance on a set of building monitoring data. To compare the different types of sensor measurements with widely varying characteristics, we use normalized root mean squared error (NRMSE) as the key metric for the effectiveness of the imputation methods. We additionally consider periodicity and run time when considering comparing methods. Through extensive testing, we find that for small gap sizes, up to 8 consecutive missing values, linear interpolation performs the best; for larger gaps stretching up to 48 consecutive missing values, K-nearest neighbors provides the most accurate imputations; for even larger gaps, more computational intensive methods, such as matrix factorization, achieve the smallest NRMSE. Additionally, we observe that these computationally intensive algorithms not only provide accurate imputations for large gaps, but are also more robust across all types of sensors.

Cho, B↗
DOE OSTI2024

A Strategic Condition Framework for Energy Innovation

Building upon previous work in innovation, technology, and economic fields, we propose a conceptual framework to address the interplay dynamics of public policy and the value chains of clean energy technology innovation systems, by focusing on market structural and strategic conditions in relation to the rate and direction of knowledge diffusion within activity-based value chains. Our framework extends beyond socio-technical transition models by considering such nuances as: 1) the implications of geography, 2) the locus of knowledge types, 3) the dynamics of financial and knowledge flow, and 4) emphasizing the importance of both market structure and institutional conditions. At the firm level, we consider dynamics of interactions between suppliers and customers, innovation activities, the competitive environment, and the firm’s broader strategic relationship to governance activities and structures; we allow for the fact that each of these aspects of a firm’s identity may have a strategically relevant geographic dimension (e.g., service territories, locational concentration of input resources, etc.). We provide a proof-of-concept application of the U.S. utility-scale solar photovoltaic (PV) and onshore wind sectors, including their interactions with the U.S. power market, which we in present in a web-based information platform (Energy I-SPARK, ei-spark.lbl.gov).

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2023

Comparing Numerical Models of the TALOS Wave Energy Converter

In this study, we present the development of a numerical model of the TALOS Wave Energy Converter (WEC) in WEC-Sim and compare it with existing numerical in-house models from Lancaster and results from DNV's Sesam code. The objective of this work is to validate the performance of the TALOS WEC using WEC-Sim and compare the results with those obtained from other numerical models. The TALOS WEC is a promising technology for the generation of clean, renewable energy from ocean waves. The development of a reliable numerical model for the TALOS WEC is crucial for its design and optimization. To achieve this, we have implemented the TALOS WEC in WEC-Sim and compared the results to in-house models from Lancaster and to results from DNV's Sesam code. Our results show good agreement with the results from Lancaster and DNV, demonstrating the accuracy and reliability of the numerical model developed in WEC-Sim. This work advances the field of wave energy conversion by providing a verified numerical model of the TALOS WEC, which can be used for further optimization and design studies.

CFD↗
DOE OSTI2025

Work In Progress: Using Internships as Means for Indirect Assessment of ABET Criteria 3 "1-7" Student Outcomes

PSU operates the Power Engineering Internship program with funding from two U.S. Department of Energy grants. The program is operated in partnership with the lead organizations of these grants, an investor-owned utility, Portland General Electric (PGE), and the Confederated Tribes of the Warm Springs (CTWS). One of the programmatic goals of the PEI is to create and sustain a clean energy engineering workforce pipeline on behalf of these lead organizations. Both grants support internships at PGE, which is also a partner on the CTWS grant. The PEI provides engineering students with year-long internships, spanning both the academic year and the summer. The interns work at PGE facilities located throughout the Portland metropolitan area. Interns are employed full-time during summers and part-time during the academic year. Proximity of the worksites to the PSU campus enables the interns to participate in the program while attending school full-time. During the academic year, students average fifteen hours per week, adjusting their work schedule according to their academic workload. The interns are allocated 930 hours per year, 480 in the summer and 450 during the academic year, which they can plan as they see fit. The internships provide meaningful financial support for the students, who can earn up to $21k if they use all of their allocated hours. Such funding is particularly important for the typical student who attends a minority serving institutions,

99 GENERAL AND MISCELLANEOUS↗
DOE OSTI2020

Compromise of Personal Protective Clothing from Liquid Exposure

Following critiques of multiple personal contamination events from entries into the Oak Ridge National Laboratory’s Spallation Neutron Source transfer bay, it was considered that the most likely causes for contamination were personal protective clothing doffing errors or that moisture (sweat) allowed contamination to wick through the protective clothing. To pursue this issue, radiological protection staff looked more closely, however, at the specific area of the clothing where contamination was highest; under enhanced lighting and photochromic manipulation, there appeared to have been some type of moisture in the area. Recognizing the possibility that moisture may have allowed for migration of contamination through the clothing, further experiments were undertaken to determine under which conditions this transport might have occurred. The objective for this work was to identify the susceptibility of different types of personal protective clothing to various liquids encountered in the workplace.Method: Several tests were performed to determine if perspiration had enabled migration of contamination, and to identify what other liquids might have affected contamination transport. Two layers of personal protective clothing were subjected to static conditions and dynamic conditions, to include active rubbing of the materials while wet. Food dye added to each of the liquids tested enabled visual indications of liquid breakthrough. Additional tests were conducted to see if solid contamination could be transported through the materials along with the liquids. As a result, it was found that all but one type of non-rubberized personal protective clothing in use at Oak Ridge National Laboratory were permanently compromised to some extent by the solvents used for decontamination. It was determined that most common cleaning agents immediately and permanently destroyed the hydrophobic nature of several of the splash-resistant protective clothing materials, allowing for radioactive contamination to penetrate through the material to the worker. Work around wet surfaces or performing wet decontamination will only be performed in protective clothing known to prevent transport of the wetting agent.

61 RADIATION PROTECTION AND DOSIMETRY↗
DOE OSTI2023

Prospective Application, Mechanism, and Deficiency of Lithium Bis(oxalate)Borate as the Electrolyte Additive for Lithium-Batteries

Lithium bis(oxalate)borate (LiBOB) is one of the most common film-forming electrolyte additives used in lithium ion batteries (LIBs), since it can form a dense boron-containing polymer as a solid electrolyte interlayer (or cathode electrolyte interlayer) in order to isolate the electrode material from the electrolyte and prevent side reactions. LiBOB can serve as HF scavenger to maintain the structural integrity of electrodes via avoiding the transition metal dissolution caused by HF attack. Additionally, LiBOB also can react with LiPF 6 to generate lithium difluoro (oxalate)borate (LiDFOB) that can be further used as a clean-up agent for reactive oxygen radicals. This article lists the application of LiBOB in high capacity and high voltage cathode materials, and also reviews the working mechanisms of LiBOB used in these materials to improve the performance of LIBs. Finally, it presents the current shortcomings of LiBOB and strategies to overcome these. This article is expected to provide useful insights for employing LiBOB as a feasible method of dealing with the difficulty of running high capacity LIBs stably under high voltage.

25 ENERGY STORAGE↗
DOE OSTI2023

An Investigation on the Pollen-Induced Soiling Losses in Utility-Scale PV Plants

Here in this study, the impact of pollen as a PV soiling agent is investigated. The performance data of five utility-scale PV plants in North Carolina, USA, was collected and analyzed using two soiling extraction methods. Satellite and environmental data, including pollen counts, cropland, and vegetation, was also collected and analyzed to identify impacts to soiling losses. During the spring peak pollen season, performance losses of >15% were observed at all five sites. Partial performance recoveries following the pollen season were slow, with lack of correlation with rainfall. This means that the statistical soiling estimation methods that assume abrupt performance recovery from rain are not appropriate for pollen-impacted solar sites. When manual cleanings were performed on site the performance recovery ranged from 5% to 11% indicating persistent soiling impacts are present in this region. The results of this work provide new insights into the phenomenon of pollen deposition on PV systems, demonstrating that 1) soiling can also affect systems located in rainy locations and 2) that its effects cannot be determined using the current estimation methodologies.

14 SOLAR ENERGY↗
DOE OSTI2020

Modulation Doping via a Two-Dimensional Atomic Crystalline Acceptor

Two-dimensional nanoelectronics, plasmonics, and emergent phases require clean and local charge control, calling for layered, crystalline acceptors or donors. Our Raman, photovoltage, and electrical conductance measurements combined with ab initio calculations establish the large work function and narrow bands of α-RuCl 3 enable modulation doping of exfoliated single and bilayer graphene, chemical vapor deposition grown graphene and WSe 2 , and molecular beam epitaxy grown EuS. We further demonstrate proof of principle photovoltage devices, control via twist angle, and charge transfer through hexagonal boron nitride. Short-ranged lateral doping (≤65 nm) and high homogeneity are achieved in proximate materials with a single layer of α-RuCl 3 . Here, this leads to the best-reported monolayer graphene mobilities (4900 cm 2 /(V s)) at these high hole densities (3 × 10 13 cm -2 ) and yields larger charge transfer to bilayer graphene (6 × 10 13 cm -2 ).

2D atomic crystals↗
DOE OSTI2024

Sonic Wafering of III-V substrates for High Efficiency Cells: A path to <$0.50/W

This project developed and demonstrated Sonic Lift-off, a novel technology that enables the reuse of expensive semiconductor substrates used to manufacture high-efficiency solar cells. By using sound waves to precisely separate thin layers of material, the process significantly reduces manufacturing costs while maintaining the performance of advanced III–V solar cells. These solar cells are among the most efficient in the world and are used in space, aerospace, and emerging terrestrial applications. The results of this work show that substrate reuse can be achieved without degrading device performance, offering a pathway to more affordable, high-performance solar technologies. This advancement supports U.S. clean energy goals by enabling broader deployment of renewable energy systems and strengthening domestic manufacturing capabilities in advanced photovoltaics.

14 SOLAR ENERGY↗
DOE OSTI2024

Evolution and interplay of lithium metal interphase components revealed by experimental and theoretical studies

ABSTRACT: Lithium metal batteries (LMB) have high energy densities and are crucial for clean energy solutions. The characterization of lithium metal interphase is fundamentally and practically important but technically challenging. Taking advantage of synchrotron x-ray which has the unique capability of analyzing crystalline/amorphous phases quantitative-ly with statistical significance, we study the composition and dynamics of LMB interphase for a newly developed im-portant LMB electrolyte that is based on fluorinated ether. Pair distribution function analysis revealed the sequential role of anion and solvent in interphase formation during cycling. The relative ratio between Li2O and LiF first increases and then decreases during cycling, suggesting suppressed Li2O formation in both initial and long extended cycles. Theoretical studies revealed that in initial cycles, this is due to the energy barrier in many-electron transfer. In long extended cycles, the anion decomposition product Li2O encourages solvent decomposition by facilitating solvent adsorption on Li2O which is followed by concurrent depletion of both. This work highlights the important role of Li2O in transitioning from anion-derived interphase to a solvent-derived one.

Tan, Sha↗
DOE OSTI2020

Enhancement of Optical Efficiency of CSP Mirrors for Reducing O&M Cost via Near-Continuous Operation of Self-Cleaning Electrodynamic Screens (EDS). Final Report

Over the past decade, techno-economical advancements in solar energy systems, particularly the improvement in the conversion efficiency of PV modules made with mono-crystalline silicon solar cells from 12% to 20%, as well as the cost reduction in manufacturing by a factor of about 10%, have made it possible to achieve a levelized cost of electricity (LCOE) in PV plants that is comparable to, or less than, the cost of deriving electricity from fossil fuels. Operating PV plants in mid-latitude sun-belt regions, where the solar irradiance level is highest, provides a high annual energy-yield (kWh/kWp) due to two factors: (1) the availability of predictable high solar irradiance throughout the year with the fewest interruptions in solar flux from clouds and rain, and (2) the increased conversion efficiency of crystalline solar cells, as recombination loss has decreased with increased intensity of the sunlight that illuminates the silicon solar cells. Semi-arid and desert regions, however, are plagued by high atmospheric dust concentrations and frequent sand storms. The deposition of a layer of dust on the optical surfaces of solar collectors such as PV modules and concentrating mirrors reduces the transmission efficiency of sunlight that actually reaches the solar cells or receivers, resulting in high energy-yield soiling loss. There are two major cost components to operating a solar plant: (1) installation costs, and (2) operation-and-maintenance (O&M) costs. There is no fuel cost; hence operating a solar plant in a semi-arid or desert region provides high returns on investment if soiling losses are mitigated via efficient cleaning methods and optimized cleaning frequency. If solar collectors are not cleaned, the accumulation of dust layers on solar collectors may cause the operation of such plants in arid regions to become economically unviable. Washing solar collectors with water and detergent, as is most commonly done now, is an efficient method for cleaning. The conventional approach in utility-scale solar plants is to use a large truck with a water tank and pump system for spraying deionized water on the surface of the solar collectors. Robotic cleaning with brushes, used for many solar plants, requires lesser water for cleaning. The water consumed using semi-automated cleaning of PV modules in utility-scale solar plants is approximately 2 liters/m 2 per cleaning cycle. The total optical surface area of the solar collectors in 1 TW-scale solar installation will be more than 3 × 109 m 2 ; hence an enormous amount of water be needed for cleaning. There simply is not enough fresh water in the sun-belt areas of the world for predicted cleaning needs. In solar power plants, the estimated cost of cleaning solar collectors includes expenses related to the equipment used, labor, cost of transportation of water, the energy required for cleaning, plus ancillary costs whereas the cost of water is not considered. The water used is obtained from sources located close to plant sites, unmindful of the environmental and societal impact as the power plants are oftentimes located in regions that face severe drought. This practice is very similar to the cost calculations in deriving the levelized cost of electricity (LCOE) in conventional power plants based on burning fossil fuel such as coal and gas, while disregarding the cost of climate change and health effects. Unless a water-free or low-water cleaning method is established, the expansion of solar plants may lose public support in areas suffering long intervals of drought. The goal of this research project has been the development and application of the Electrodynamic Screen (EDS) as a means for a water-free, scalable cleaning process applicable to solar-power installations, including rooftop applications. We describe here the development of an EDS film-based cleaning process as an emerging method for use on PV modules, parabolic troughs, and heliostats. This report aims to show the feasibility of integrating or retrofitting EDS films onto the optical surfaces of solar collectors (both PV and CSP) while maintaining high transmission or reflection efficiency. The cleaning action provided by the EDS film is an active method to remove dust deposits by electrodynamic force. Current lab-scale prototype EDS films, retrofitted onto solar panels and mirrors, have shown to be capable of maintaining optical transmission or specular-reflection efficiencies higher than 90% of initial values under clean conditions. The optical surfaces of solar collectors laminated with EDS films can remove more than 90% of deposited dust when the EDS is activated for less than two minutes. As an electrodynamic dust removal process, the EDS film-based method is designed primarily for the removal of dust in solar installations located in semi-arid and desert areas, where the atmosphere is often dry and dusty and rainfall is infrequent. While EDS film application minimizes water consumption and facilitates cleaning as frequently as needed, it has limitations in removing contaminants such as soot, organic pollutants deposited as fine films on the surface, and bird droppings. The dust removal efficiency of the EDS is maximum at relative humidity RH is 40 to 50% and decreases at when RH > 65%. Many solar plant sites undergo diurnal and seasonal cycles of high ambient, early afternoon temperatures and an RH that reaches the dew point early in the morning. These variations in atmospheric conditions do not limit the operation of the EDS film. This report presents a brief review of the progress and the potential of EDS film technology for mitigating the impact of dust on solar collectors via water-free cleaning, as well as current technical challenges regarding efficiency and durability. Our experimental data on the performance of EDS films show that: (1) the dust-removal efficiency (DRE) can reach levels higher than 90%, (2) the specular reflectivity (SR) of EDS film-laminated second-surface mirrors reach levels in excess of 90%, (3) the specular reflectivity restoration (SRR) can exceed 90%, (4) the output-power restoration (OPR) of PV modules can exceed 95%, and (5) the optical transmission efficiency (TE) of the EDS films can be greater than 90%. Working with Sandia National Laboratories (NM), Corning Research and Development Corporation (NY), Eastman Kodak (NY), Tomark-Worthen Industries (NH), and EDS Chile SPA (Chile), we have produced EDS film-laminated PV modules and demonstrated their self-cleaning functions without requiring water. We have demonstrated that the operational range of EDS films will cover the expected ambient temperature of solar fields at RH cycling varying from 20 to 95% as long as the EDS films are activated in the RH range 20 to 50%. (Typical solar-field climates in deserts and semi-arid lands often reach near dew point in coastal areas.) Our experiments on the application of hydrophobic-fluorinated nanoparticle coatings on EDS film surfaces show that the EDS operational range can be extended to higher RH levels that approach the dew point. At Eastman Kodak, as one of our industrial partners, we were able to establish a process for manufacturing EDS films using flexographic printing of the electrodes onto transparent polymer films. This process utilizes an existing manufacturing line at Eastman Kodak that allows fabrication of medium-scale EDS films (26 cm × 30 cm). The manufacturing process has the capacity to produce EDS films at high production speeds. The medium-scale EDS films that have been printed at Kodak were evaluated in the lab at Boston University. The EDS films produced at Kodak were laminated at Tomark-Worthen using an industrial scale vacuum laminator to produce EDS film stacks, which can be affixed onto the optical surfaces of PV modules or concentrating mirrors. The EDS film stack consists of the EDS films that have Willow® Glass (WG) which has a thickness of 100 μm as the front surface. The WG sheets obtained from Corning Research and Development Corporation are customized in size and shape to cover the active area of the EDS films. The back surface of the EDS film stack is integrated onto the optical surface of the solar panel or mirror using optically clear adhesive (OCA) films or silicone adhesives. The OCA films (thickness 25 μm) are produced by 3M. The EDS film stacks have the architecture: WG/OCA/EDS Film/OCA/ over PV module or solar mirror. The power-supply units needed for activating the electrodes of the EDS film were designed and produced at Boston University. These power supply units provide three-phase, 1.2 kV voltage pulses at a very low current (micro-ampere) level and at a low frequency (≈ 5 Hz). The voltage pulses are applied to the electrodes in a sequence such that the train of pulses resembles a unidirectional traveling wave of electrical field on the surface of the EDS film. The dust particles on the surface become charged electrostatically and are levitated by the Coulomb force. The lateral sweeping action of the traveling electric field created by the three-phase voltages pulses then sweeps the dust off the surface. The energy consumed by the EDS electrodes is less than 0.2 Wh/m 2 /cleaning cycle, enabling energy-efficient restoration of output power (OPR) of PV module or specular reflectivity restoration (SRR) for solar mirrors. The EDS system consists of (1) an EDS film stack laminated onto the solar collectors, (2) connection of the EDS film to its power supply unit and (3) Interconnection of the power supply to PV modules or solar mirrors. Design, construction and assessment of field-testing units that have EDS stack laminated PV modules for evaluating the performance of the EDS films in solar fields is being carried out at BU. Our progress under this project, aimed at the advancement of EDS film technology, has reached DOE Technology Readiness Level (TRL) 6. Based on the extensive laboratory evaluations and limited field trials, as well as contacts with potential users, we believe that the technology has reached its commercial stage. We are conducting a cost analysis using the National Renewable Energy Laboratory (NREL) System Advisory Model (SAM) and are preparing for field trials of EDS films in different solar fields in the US, Chile, India and in the Middle East. A brief description of EDS film performance, construction and testing of the field-test unit, autonomous operation of the field-test unit for evaluating EDS performance in increasing energy yield, associated revenue savings, and water conservation is presented.

14 SOLAR ENERGY↗
DOE OSTI2023

Enhanced, continuous, liquid-liquid extraction and in-situ separation of volatile fatty acids from fermentation broth

In 2018 alone, the US landfilled 35.3 million tons of food waste, about 24% of the total landfilled mass. In addition to the negative impacts landfills have demonstrated on the environment and human health, some states have begun to outlaw or dissuade the disposal of food waste and sewage sludge into landfills altogether. An urgent need has thus been created for the development of digestion processes like anaerobic digestion (AD) and arrested methanogenesis (AM) to convert food waste into valuable chemical products. Unfortunately, the buildup of volatile fatty acids (VFAs) during these processes eventually halts the reaction, and energy efficient methodologies for VFA removal are critical for the operation of fermenters. Additionally, VFAs themselves can serve as valuable chemical precursors, and recently AD processes have been modified to increase VFA production during fermentation. However, even with significant research over the past three decades, the separation of VFAs from the fermenter broth has remained expensive. Moreover, the separation of these VFAs from the fermenter broth may cost up to 50% of the entire process budget, hindering the widespread commercial adoption of AD and AM. Here we present a novel liquid-liquid extraction process termed CLEANS (Continuous Liquid-liquid Extraction And iN-situ Separation) as a highly efficient method for continuously separating VFAs from a real fermentation broth solely under gravity. Our optimized process (using an aqueous broth feed pH of 2.5, tri-noctylamine as an extractant, and a 10:1 ratio of aqueous broth to organic extractant), achieved a VFA distribution constant K D = 44.5 ± 7.9, a single-pass recovery = 81.3 ± 2.5%, and an extraction factor = 8.1 ± 0.3. These KD values are over an order of magnitude higher than what has been previously reported for comparable processes. A high aqueous-to-organic flowrate ratio, enabled for the first time by CLEANS, was found to be particularly crucial for achieving optimal extraction. Our separation process demonstrates excellent reproducibility and potential for scalability. The economic and environmental implications of this work are briefly discussed.

42 ENGINEERING↗
DOE OSTI2023

COP28 Outcomes Report: Executive Summary

Net Zero World, launched at COP26, is a flagship U.S. effort to partner with countries in accelerating transitions to clean energy systems. This initiative brings together world-class experts and resources from 10 U.S. Department of Energy national laboratories and nine U.S. government agencies. Collaboratively, they work with technical and government representatives from Argentina, Chile, Egypt, Indonesia, Nigeria, Singapore, Thailand, and Ukraine to advance decarbonization in these economies.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2022

Sustainable and Resilient Communities Table Topic

At its 2022 annual meeting, JISEA presents on sustainable and resilient communities, including an overview of JISEA case studies on energy and agriculture in Colorado and work by JISEA's Sustainable Communities Catalyzer. The catalyzer completed a study on intersecting disadvantaged community indicators with renewable energy deployment potential to identify communities where deployment of clean energy could have the biggest local impact.

agriculture↗
DOE OSTI2023

Pollen and Bio-Soiling in the Southeast U.S.

Typical PV soiling models presume that soiling follows a sawtooth pattern: linear soiling during dry periods followed by abrupt recovery or cleaning during rainfall events. Due to frequency of rainfall in the in the eastern U.S. sawtooth soiling models report near zero soiling losses in this region. Alternatively, through work with system owner/operators per NREL's PVfleet project it has become clear that there are systems in the Southeast that have soiled as high as 10% which are not recovering with regular rainfall. The current hypothesis is that sticky soiling due to pollen or other biological sources is persistent to rainfall removal. Field data and the latest progress towards de-risking bio-soiling will be presented.

photovoltaic↗