Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “transparency”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17

Slightly Conductive Transparent Films for Space Applications: Manufacturability and Durability

Highly transparent, slightly conductive films of co-deposited indium tin oxide (ITO) and MgF, have possible applications for environmental protection of exterior surfaces of spacecraft. Reliable preparation of films with the desired sheet resistivity (approximately 10(exp 8) ohms/square) is difficult because the electrical properties of ITO-Mg F, are highly dependent on film composition. We have investigated the use of plasma emission monitoring to improve the reproducibility of films prepared by RF magnetron sputtering. While considerable improve ment was observed, it appears that some in-situ electrical or optica l characterization will be needed for reliable production coating wit h ITO-MgF,. We have also done further evaluation of a possibly undesi rable photoconductive effect previously observed in these films.

Uppala, N.↗

Is the Universe More Transparent to Gamma Rays than Previously Thought?

The MAGIC collaboration has recently reported the detection of the strong gamma-ray blazar 3C279 during a 1-2 day flare. They have used their spectral observations to draw conclusions regarding upper limits on the opacity of the Universe to high energy gamma-rays and, by implication, upper limits on the extragalactic mid-infrared background radiation. In this paper we examine the effect of gamma-ray absorption by the extragalactic infrared radiation on intrinsic spectra for this blazar and compare our results with the observational data on 3C279. We find agreement with our previous results, contrary to the recent assertion of the MAGIC group that the Universe is more transparent to gamma-rays than our calculations indicate. Our analysis indicates that in the energy range between approx. 80 and approx. 500 GeV, 3C279 has a best-fit intrinsic spectrum with a spectral index approx. 1.78 using our fast evolution model and approx. 2.19 using our baseline model. However, we also find that spectral indices in the range of 1.0 to 3.0 are almost as equally acceptable as the best fit spectral indices. Assuming the same intrinsic spectral index for this flare as for the 1991 flare from 3C279 observed by EGRET, viz., 2.02, which lies between our best fit indeces, we estimate that the MAGIC flare was approx.3 times brighter than the EGRET flare observed 15 years earlier.

Stecker, Floyd W.↗

A Study of Transparent Plastics for use on Aircraft, Special Report

Various transparent organic plastics, including both commercially available and experimental materials, have been examined to determine their suitability for use as flexible windshields on aircraft, The properties which have been studied include light transmission, haziness, distortion, resistance to weathering, scratch and indentation hardness, impact strength, dimensional stability, resistance to water and various cleaning fluids, bursting strength at normal and low temperatures, and flammability.

Axilrod, Benjamin M.↗

A Study of Transparent Plastics for use on Aircraft. Supplement

This supplement to a NACA study issued in May 1937 entitled "A Study of Transparent Plastics for Use on Aircraft", contains two tables. These tables contain data on bursting strengths of plastics, particularly at low temperatures. Table 1 contains the values reported in a table of the original memorandum, and additional values obtained at approximately 25 C, for three samples of Acrylate resin. The second table contains data obtained for the bursting strength when one surface of the plastic was cooled to approximately -35 C.

Axilrod, Benjamin M.↗

Transparent Conveyor of Dielectric Liquids or Particles

The concept of a transparent conveyor of small loose dielectric parti cles or small amounts of dielectric liquids has emerged as an outgro wth of an effort to develop efficient, reliable means of automated re moval of dust from solar cells and from windows of optical instrumen ts. This concept is based on the previously reported concept of an e lectrodynamic screen, according to which a grid-like electric field is established on and near a surface and is moved along the surface p erpendicularly to the grid lines. The resulting electrodynamic force s on loose dielectric particles or dielectric liquid drops in the vic inity would move the particles or drops along the surface. In the or iginal dust-removal application, dust particles would thus be swept out of the affected window area. Other potential applications may occ ur in nanotechnology -- for example, involving mixing of two or more fluids and/or nanoscale particles under optical illumination and/or optical observation.

Calle, Carlos I.↗

Monolithic Parallel Tandem Organic Photovoltaic Cell with Transparent Carbon Nanotube Interlayer

We demonstrate an organic photovoltaic cell with a monolithic tandem structure in parallel connection. Transparent multiwalled carbon nanotube sheets are used as an interlayer anode electrode for this parallel tandem. The characteristics of front and back cells are measured independently. The short circuit current density of the parallel tandem cell is larger than the currents of each individual cell. The wavelength dependence of photocurrent for the parallel tandem cell shows the superposition spectrum of the two spectral sensitivities of the front and back cells. The monolithic three-electrode photovoltaic cell indeed operates as a parallel tandem with improved efficiency.

Tanaka, S.↗

Extracting Oxygen from Lunar Simulant Using a Transparent Furnace Pulsed Fluidized Bed

In the event that humans return to the moon, utilizing the local materials will be beneficial for extended stays. Rather than transporting resources, such as oxygen, from Earth, NASA is investigating methods of extracting it from lunar regolith. One promising process is hydrogen reduction. In the hydrogen reduction process, lunar regolith is heated to 1000 C in the presence of hydrogen. The iron oxide (Fe-O) bonds, found in lunar material, are broken and the hydrogen attracts the oxygen to produce water vapor [Allen et al., 1996]. FeO + H2 (right arrow) Fe +H2O. The water vapor is then captured, cleaned, and electrolyzed. The hydrogen is recycled back to the reduction process and the oxygen is stored until consumed by an end user (propulsion, life support, etc.). To obtain a good oxygen yield, the majority of lunar regolith must be exposed to the hydrogen gas and have a high rate of heat transfer from heat source to particle. This is achieved with good solids mixing via fluidization or mechanical agitation. In Generation II of the ROxygen program, the ROxygen Team at Johnson Space Center (JSC) investigated the feasibility of gas only pulsed fluidization as the only means to mix synthetic lunar regolith (simulant) at high temperatures. Fluidized beds have been used in industry to effectively process powders for decades. They consist of gas flowing upward through a bed of particles. The stirring action continuously moves the grains around to achieve uniform mixing of gas, solids, and heat [Geldart, 1986]. A transparent furnace unit was developed by Thoughventions Unlimited LLC (TvU) to aid in the qualitative observation of the fluidization behavior at high temperatures. Multipoint thermocouples and pressure sensors provided quantitative information regarding the quality of mixing. The water produced was measured using humidity sensors and captured using a NASA designed and built condenser. Once the simulant was processed, pneumatically transporting the 'hot' simulant out of the furnace was investigated.

Oryshchyn, L.↗

Transparent Metal-Salt-Filled Polymeric Radiation Shields

"COR-RA" (colorless atomic oxygen resistant -- radiation shield) is the name of a transparent polymeric material filled with x-ray-absorbing salts of lead, bismuth, cesium, and thorium. COR-RA is suitable for use in shielding personnel against bremsstrahlung radiation from electron-beam welding and industrial and medical x-ray equipment. In comparison with lead-foil and leaded-glass shields that give equivalent protection against x-rays (see table), COR-RA shields are mechanically more durable. COR-RA absorbs not only x-rays but also neutrons and rays without adverse effects on optical or mechanical performance. The formulation of COR-RA with the most favorable mechanical-durability and optical properties contains 22 weight percent of bismuth to absorb x-rays, plus 45 atomic percent hydrogen for shielding against neutrons.

Edwards, David↗

Large-Strain Transparent Magnetoactive Polymer Nanocomposites

A document discusses polymer nano - composite superparamagnetic actuators that were prepared by the addition of organically modified superparamagnetic nanoparticles to the polymer matrix. The nanocomposite films exhibited large deformations under a magnetostatic field with a low loading level of 0.1 wt% in a thermoplastic polyurethane elastomer (TPU) matrix. The maximum actuation deformation of the nanocomposite films increased exponentially with increasing nanoparticle concentration. The cyclic deformation actuation of a high-loading magnetic nanocomposite film was examined in a low magnetic field, and it exhibited excellent reproducibility and controllability. Low-loading TPU nanocomposite films (0.1-2 wt%) were transparent to semitransparent in the visible wavelength range, owing to good dispersion of the magnetic nanoparticles. Magnetoactuation phenomena were also demonstrated in a high-modulus, high-temperature polyimide resin with less mechanical deformation.

Meador, Michael A.↗

Transparent and Electrically Conductive Carbon Nanotube-Polymer Nanocomposite Materials for Electrostatic Charge Dissipation

In recent years, nanocomposite materials have been extensively studied because of their superior electrical, magnetic, and optical properties and large number of possible applications that range from nano-electronics, specialty coatings, electromagnetic shielding, and drug delivery. The aim of the present work is to study the electrical and optical properties of carbon nanotube(CNT)-polymer nanocomposite materials for electrostatic charge dissipation. Single and multi-wall carbon nanotubes were grown by catalytic chemical vapor deposition (CCVD) on metal/metal oxide catalytic systems using acetylene or other hydrocarbon feedstocks. After the purification process, in which amorphous carbon and non-carbon impurities were removed, the nanotubes were functionalized with carboxylic acid groups in order to achieve a good dispersion in water and various other solvents. The carbon nanostructures were analyzed, both before and after functionalization by several analytical techniques, including microscopy, Raman spectroscopy, and X-Ray photoelectron spectroscopy. Solvent dispersed nanotubes were mixed (1 to 7 wt %) into acrylic polymers by sonication and allowed to dry into 25 micron thick films. The electrical and optical properties of the films were analyzed as a function of the nanotubes' concentration. A reduction in electrical resistivity, up to six orders of magnitude, was measured as the nanotubes' concentration in the polymeric films increased, while optical transparency remained 85 % or higher relative to acrylic films without nanotubes.

Dervishi, E.↗

A Novel Hybrid Ultramicrotomy/FIB-SEM Technique: Preparation of Serial Electron-Transparent Thin Sections of a Hayabusa Grain

The Japanese space agency's (JAXA) Hayabusa mission returned the first particulate samples (typically <100micron) from the surface of an asteroid (25143 Itokawa). These precious samples provide important insights into early Solar System processes, but their sizes pose tremendous challenges to coordinated analysis using a variety of nano- and micro-beam techniques. The ability to glean maximal information from individual particles has become increasingly important and depends critically on sample preparation. We developed a hybrid technique combining traditional ultramicrotomy with focused ion beam (FIB) techniques, allowing for more thorough in situ investigations of grain surfaces and interiors. Using this method, we increase the number of FIB-prepared sections that can be recovered from a particle with dimensions on the order of tens of microns. These sections can be subsequently analyzed using a variety of analytical techniques. Particle RA-QD02-0211 is a approx. 40×40×20 micron particle from Itokawa containing olivine and Fe sulfides. It was embedded in low viscosity epoxy and partly sectioned to a depth of approx 10 micron; sections are placed on Cu grids with thin amorphous films for transmission electron microscope (TEM) analyses. With the sample surface partly exposed, the epoxy bullet is trimmed to a height of approx. 5mm to accommodate the allowable dimensions for FIB work (FEI Quanta 600 3D dual beam FIB-SEM). Using a diamond trim knife, the epoxy surrounding the grain is removed on 3 sides (to within a few microns of the grain); the depth of material removed extends well below the bottom of the particle. The sample is attached to an SEM pin mount, the epoxy coated with conductive paint, and the entire assembly coated with approx. 40nm of carbon to eliminate sample charging during FIB work. A protective carbon cap is placed according to the plan for the 15 FIB sections. The central 'spine' of the cap runs perpendicular to the front of the sample, and the 'ribs' protruding from either side run parallel. Each rib indicates the location of a planned FIB section, and the spine contains the final two planned sections. We use a cap with a 4 micron-wide spine and 2micron-wide ribs that have ≳3.5 micron of space between them (narrower cuts result in too much re-deposition of material inside the trenches). Using a 30kV, 3nA ion-beam we expose the front surface of the grain and commence milling trenches between sections. Rather than using the typical C-cut to prepare the sample for lift-out, an L-cut is used instead, leaving the sample connected by an interior tab. tab. Sections are lifted out, attached to TEM grids and thinned to electron transparency. TEM analyses show that our hybrid technique preserves both interior and edge features, including surface modifications from exposure to the space environment, such as damaged rims that form in response to solar wind implantation effects and adhering grains. In addition, the FIB sections provide larger areas that are free of fractures and chatter effects in comparison to the microtome thin sections, thus enabling more accurate measurements of solar flare particle track densities that are used to determine the surface exposure age of the particles.

Berger, Eve L.↗

Secured Optical Communications Using Quantum Entangled Two-Photon Transparency Modulation

A system and method is disclosed wherein optical signals are coded in a transmitter by tuning or modulating the interbeam delay time (which modulates the fourth-order coherence) between pairs of entangled photons. The photon pairs are either absorbed or not absorbed (transparent) by an atomic or molecular fluorescer in a receiver, depending on the inter-beam delay that is introduced in the entangled photon pairs. Upon the absorption, corresponding fluorescent optical emissions follow at a certain wavelength, which are then detected by a photon detector. The advantage of the disclosed system is that it eliminates a need of a coincidence counter to realize the entanglement-based secure optical communications because the absorber acts as a coincidence counter for entangled photon pairs.

Kojima, Jun↗

Three-dimensional in Situ Observations of Polycrystalline Microstructure Evolution During Directional Solidification of Transparent Alloys Aboard the ISS and Quantitative Comparison with Numerical Modeling

Cellular/dendritic microstructures formed during solidification have a crucial influence on the mechanical properties of a wide range of structural alloys. By minimizing the amount of gravity-induced convection in the liquid, directional solidification experiments using transparent organic alloys conducted in the DECLIC-DSI onboard the International Space Station have provided unique 3D in situ observations of the spatiotemporal evolution of the solid-liquid interface during the formation of cellular and dendritic microstructures under purely diffusive growth conditions in polycrystalline samples containing several grains with a small misorientation with respect to the temperature gradient. Those observations have made it possible to perform benchmark quantitative comparisons with the predictions of state-of-the-art phase-field simulations of microstructure formation in 3D on experimentally relevant length and time scales. This talk will report quantitative comparisons between microgravity experiments and phase-field simulations in succinonitrile-camphor alloys of two different compositions that shed new light on the role of subgrain boundaries in the spatiotemporal evolution of the primary cellular spacing and the selection of dendritic array structures.

Kaihua Ji↗

Burning Embers: Towards More Transparent and Robust Climate-change Risk Assessments

The Intergovernmental Panel on Climate Change (IPCC) reports provide policy-relevant insights about climate impacts, vulnerabilities and adaptation through a process of peer-reviewed literature assessments underpinned by expert judgement. An iconic output from these assessments is the burning embers diagram, first used in the Third Assessment Report to visualize reasons for concern, which aggregate climate-change-related impacts and risks to various systems and sectors. These burning embers use colour transitions to show changes in the assessed level of risk to humans and ecosystems as a function of global mean temperature. In this Review, we outline the history and evolution of the burning embers and associated reasons for concern framework, focusing on the methodological approaches and advances. While the assessment framework and figure design have been broadly retained over time, refinements in methodology have occurred, including the consideration of different risks, use of confidence statements, more formalized protocols and standardized metrics. Comparison across reports reveals that the risk level at a given temperature has generally increased with each assessment cycle, reflecting accumulating scientific evidence. For future assessments, an explicit, transparent and systematic process of expert elicitation is needed to enhance comparability, quality and credibility of burning embers.

burning embers diagram↗

Phase control of electromagnetically induced transparency and its applications to tunable group velocity and atom localization

We show that, by simple modifications of the usual three-level lambda-type scheme used in electromagnetically induced transparency (EIT) schemes, phase dependence in the response of the atomic medium to a weak probe field can be introduced. This gives rise to phase dependent susceptibility. By properly controlling phase and amplitudes of the drive fields we obtain variety of interesting effects. On one hand we obtain phase control of the group velocity of a probe field passing through medium to the extend that continuous tuning of the group velocity from subluminal to superluminal and back is possible. While on the other hand, by choosing one of the drive fields to be a standing wave field inside a cavity, we obtain sub-wavelength localization of moving atoms passing through the cavity field.

Zubairy, M. Suhail↗

Design of ZnSe QPM for Wide Transparency Sensing and Laser Applications

ZnSe has been a great choice for the rare-earth and transition metal doping to develop lasers. It is an excellent materialfor variety of optical applications due to wide transparency range, good fabricability and very low optical absorptionsimilar to other selenides. NASA Marshall Space Flight Center has developed large crystals using physical vapordeposition (PVD) doped with transition metals for lasing. GaAs based quasi-phase matched structures have a lot oflimitations including difficulty of frequency conversion from available high power lasers. We are developing Si- andGaAs- based templates and using microfabrication process to deposit ZnSe using physical vapor transport (PVT)method. Experimental results of the fabrication of templates and growth of ZnSe on templates will be presented.

Epitaxial↗

INCREASING THE TRANSPARENCY AND REPRODUCIBILITY OF SPACE RADIATION SCIENCE: THE RADIATION BIOLOGY ONTOLOGY

Among the primary objectives of the Open/Open-Source Science paradigm are making scientific investigation data transparent and results reproducible [1], objectives shared by the FAIR principles [2]. To accomplish this, the conceptual framework that includes all the investigation objects needs to be accurately captured and communicated to all data consumers. A large part of this requires using metadata standards to annotate data collected. These standards should be readily accessible, informed by scientific community consensus and sufficiently specific to encompass all of the important aspects of the investigation. Starting in 2020 we have been co-leading an open consortium to develop a new metadata standard, the Radiation Biology Ontology (RBO), through the Open Biological and Biomedical Ontologies (OBO) Foundry [3]. We began by transforming many of the terms from the National Council on Radiation Protection and Measurement into concepts that can be formally related to existing OBO Foundry classes or attributes. We then identified and imported into the RBO existing OBO Foundry classes that have obvious relevance for radiation biomedicine (for example, concepts from the Environment Ontology that describe radiative processes, and concepts from the Gene Ontology dealing with molecular and cellular responses to radiation). Finally, we scrutinized datasets from investigations of radiation effects held in NASA GeneLab and LSDA repositories and added additional classes, instances, and attributes into the RBO that should be used to annotate these data. We developed the RBO using the open-source tools of GitHub and publish the RBO periodically through the NIH/NCBI BioPortal website, so systems worldwide can leverage the knowledge it contains [4]. This initial phase of concept modeling has yielded an RBO that at present has more than 300 declared concepts, with more than 3500 additional concepts imported from other OBO Foundry ontologies. While this first phase has focused on concepts for annotating samples, environments, exposures, and measurements, the next phase will center on supporting annotation of results and findings, such as concept models of molecular, cellular and tissue effects. The value of the RBO will be determined in part by our ability to engage the community in its development, and we have established a Radiobiology Informatics Consortium with unrestricted membership as the owner of the RBO in order to encourage investigators, system owners and other to join in this effort. Anyone can report issues or request new concept modeling or other features directly on GitHub. By using the BioPortal application programming interface, systems can pose dynamic queries to the latest version of the RBO for information on individual classes or entire hierarchies; this design eliminates the need for systems to be updated in order to use newer versions of the RBO. We hope to contribute to the advancement of open radiobiological science through the continued, open development of the RBO, that will provide more precise, machine-interpretable descriptions of investigations, as well as support data meta-analysis through machine learning or other artificial intelligence methods. REFERENCES [1] Open science in space. Nature Medicine, 2021. 27(9): p. 1485-1485. [2] Wilkinson, M.D., et al., The FAIR Guiding Principles for scientific data management and stewardship. Sci Data, 2016. 3: p. 160018. [3] Smith, B., et al., The OBO Foundry: coordinated evolution of ontologies to support biomedical data integration. Nat Biotechnol, 2007. 25(11): p. 1251-5. [4] Whetzel, P.L., et al., BioPortal: enhanced functionality via new Web services from the National Center for Biomedical Ontology to access and use ontologies in software applications. Nucleic Acids Res, 2011. 39(Web Server issue): p. W541-5.

informatics↗

Three-Dimensional In Situ Observations of Polycrystalline Microstructure Evolution During Directional Solidification of Transparent Alloys Aboard the ISS and Quantitative Comparison with Numerical Modeling

Cellular/dendritic microstructures formed during solidification have a crucial influence on the mechanical properties of a wide range of structural alloys. By minimizing the amount of gravity-induced convection in the liquid, directional solidification experiments using transparent organic alloys conducted in the DECLIC-DSI onboard the International Space Station have provided unique 3D in situ observations of the spatiotemporal evolution of the solid-liquid interface during the formation of cellular and dendritic microstructures under purely diffusive growth conditions. Those observations have made it possible to perform benchmark quantitative comparisons with the predictions of state-of-the-art phase-field simulations of microstructure formation in 3D on experimentally relevant length and time scales. This talk will report quantitative comparisons between microgravity experiments and phase-field simulations in succinonitrile-camphor alloys of two different compositions, which shed new light on the selection of dendritic array structures, and on roles of macroscopic curvatures and subgrain boundaries between grains with a small misorientation with respect to the temperature gradient in the spatiotemporal evolution of the primary cellular spacing.

Kaihua Ji↗