Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “transitivity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
NASA NTRS1988

Effect of Transition Aerodynamics on Aeroassist Flight Experiment Trajectories

Various transition methods are used here to study the viscous effects encountered in low density, hypersonic flight, through the transition from free molecular to continuum flow. Methods utilizing Viking data, Shuttle Orbiter data, a Potter number parameter, and a Shock Reynolds number were implemented in the Program to Optimize Simulated Trajectories (POST). Simulations of the Aeroassist Flight Experiment (AFE) using open loop guidance were used to assess the aerodynamic performance of the vehicle. A bank angle was found for each transition method that would result in a 200 nautical-mile apogee. Once this was done, the open loop guidance was replaced by the proposed guidance algorithm for the AFE. Simulations were again conducted using that guidance and the different transitions for comparison. For the gains used, the guidance system showed some sensitivity in apogee altitude to the transition method assumed, but the guidance was able to successfully complete the mission.

Minier, Elizabeth A.↗
NASA NTRS1988

Two-Equation Low-Reynolds-Number Turbulence Modeling of Transitional Boundary Layer Flows Characteristic of Gas Turbine Blades

The use of low Reynolds number (LRN) forms of the k-epsilon turbulence model in predicting transitional boundary layer flow characteristic of gas turbine blades is developed. The research presented consists of: (1) an evaluation of two existing models; (2) the development of a modification to current LRN models; and (3) the extensive testing of the proposed model against experimental data. The prediction characteristics and capabilities of the Jones-Launder (1972) and Lam-Bremhorst (1981) LRN k-epsilon models are evaluated with respect to the prediction of transition on flat plates. Next, the mechanism by which the models simulate transition is considered and the need for additional constraints is discussed. Finally, the transition predictions of a new model are compared with a wide range of different experiments, including transitional flows with free-stream turbulence under conditions of flat plate constant velocity, flat plate constant acceleration, flat plate but strongly variable acceleration, and flow around turbine blade test cascades. In general, calculational procedure yields good agreement with most of the experiments.

Schmidt, Rodney C.↗
NASA NTRS1988

Techniques used in the F-14 variable-sweep transition flight experiment

This paper discusses and evaluates the test measurement techniques used to determine the laminar-to-turbulent boundary layer transition location in the F-14 variable-sweep transition flight experiment (VSTFE). The main objective of the VSTFE was to determine the effects of wing sweep on the laminar-to-turbulent transition location at conditions representative of transport aircraft. Four methods were used to determine the transition location: (1) a hot-film anemometer system; (2) two boundary-layer rakes; (3) surface pitot tubes; and (4) liquid crystals for flow visualization. Of the four methods, the hot-film anemometer system was the most reliable indicator of transition.

Anderson, Bianca Trujillo↗
NASA NTRS1988

Techniques used in the F-14 variable-sweep transition flight experiment

This paper discusses and evaluates the test measurement techniques used to determine the laminar-to-turbulent boundary-layer transition location in the F-14 variable-sweep transition flight experiment (VSTFE). The main objective of the VSTFE was to determine the effects of wing sweep on the laminar-to-turbulent transition location at conditions representative of transport aircraft. Four methods were used to determine the transition location: (1) a hot-film anemometer system, (2) two boundary-layer rakes, (3) surface pitot tubes, and (4) liquid crystals for flow visualization. Of the four methods, the hot-film anemometer system was the most reliable indicator of transition.

Trujillo Anderson, Bianca↗
NASA NTRS1989

Studies of transition in boundary layers

Some current studies on transition in boundary layers are briefly reviewed, including work based on the asymptotic transition theory. In particular, attention is given to the appearance of transition, primary instability, transition criterion, nonparallelism and nonlinearity, multistructural approach to transition, and two-dimensional nonlinear interactions. The discussion also covers secondary instability, three-dimensional interactions, Floquet theory of secondary instability, breakdown, and boundary-layer receptivity.

Herbert, Thorwald↗
NASA NTRS1990

A cloudiness transition in a marine boundary layer

Boundary layer cloudiness plays several important roles in the energy budget of the earth. Low level stratocumulus are highly reflective clouds which reduce the net incoming shortwave radiation at the earth's surface. Climatically, the transition to a small area fraction of scattered cumulus clouds occurs as the air flows over warmer water. Although these clouds reflect less sunlight, they still play an important role in the boundary layer equilibrium by transporting water vapor upwards, and enhancing the surface evaporation. The First ISCCP (International Satellite Cloud Climatology Project) Regional Experiment (FIRE) included a marine stratocumulus experiment off the southern California coast from June 29 to July 19, 1987. The objectives of this experiment were to study the controls on fractional cloudiness, and to assess the role of cloud-top entrainment instability (CTEI) and mesoscale structure in determining cloud type. The focus is one research day, July 7, 1987, when coordinated aircraft missions were flown by four research aircraft, centered on a LANDSAT scene at 1830 UTC. The remarkable feature of this LANDSAT scene is the transition from a clear sky in the west through broken cumulus to solid stratocumulus in the east. The dynamic and thermodynamic structure of this transition in cloudiness is analyzed using data from the NCAR Electra. By averaging the aircraft data, the internal structure of the different cloud regimes is documented, and it is shown that the transition between broken cumulus and stratocumulus is associated with a change in structure with respect to the CTEI condition. However, this results not from sea surface temperature changes, but mostly from a transition in the air above the inversion, and the breakup appears to be at a structure on the unstable side of the wet virtual adiabat.

Betts, Alan K.↗
NASA NTRS1990

Lower solar chromosphere-corona transition region. I - Theoretical models with small temperature gradients

A study of transition region models including the effects of classical thermal conduction, heating, and radiative cooling is carried out with attention directed toward the problem of understanding the observed emission in the lower transition region. It is found that the observationally inferred emission measure curve implies a near-balance between heating and radiative cooling in the lower transition region, and that the presence of strong hydrogen Ly-alpha cooling leads to the existence of singularities in the solutions of the force balance and energy balance equations when such a near-balance between heating and cooling is assumed. These singularities place strong constraints on the nature of viable models of the lower transition region and must be considered when Ly-alpha cooling is important. Previously suggested explanations of the observed emission from the lower transition region are considered in the context of the results of the present study, and conditions for the applicability of these suggested explanations are discussed.

Woods, D. Tod↗
NASA NTRS1990

Critical behavior in the hydrogen insulator-metal transition

The vibrational Raman spectrum of solid hydrogen has been measured from 77 to 295 K in the vicinity of the recently observed insulator-metal transition and low-temperature phase transition at 150 gigapascals. The measurements provide evidence for a critical point in the pressure-temperature phase boundary of the low-temperature transition. The result suggests that below the critical temperature the insulator-metal transition changes from continuous to discontinuous, consistent with the general criteria originally proposed by Mott (1949) for metallization by band-gap closure. The effect of temperature on hydrogen metallization closely resembles that of the lower-pressure insulator-metal transitions in doped V2O3 alloys.

Hemley, R. J.↗
NASA NTRS1990

Computational analysis of flow in 3D propulsive transition ducts

A numerical analysis of fully three dimensional, statistically steady flows in propulsive transition ducts being considered for use in future aircraft of higher maneuverability is investigated. The purpose of the transition duct is to convert axisymmetric flow from conventional propulsion systems to that of a rectangular geometry of high aspect ratio. In an optimal design, the transition duct would be of minimal length in order to reduce the weight penalty, while the geometrical change would be gradual enough to avoid detrimental flow perturbations. Recent experiments conducted at the Propulsion Aerodynamics Branch have indicated that thrust losses in ducts of superelliptic cross-section can be surprisingly low, even if flow separation occurs near the divergent walls. In order to address the objective of developing a rational design procedure for optimal transition ducts, it is necessary to have available a reliable computational tool for the analysis of flows achieved in a sequence of configurations. Current CFD efforts involving complicated geometries usually must contend with two separate but interactive aspects: namely, grid generation and flow solution. The first two avenues of the present investigation were comprised of suitable grid generation for a class of transition ducts of superelliptic cross-section, and the subsequent application of the flow solver PAB3D to this geometry. The code, PAB3D, was developed as a comprehensive tool for the solution of both internal and external high speed flows. The third avenue of investigation has involved analytical formulations to aid in the understanding of the nature of duct flows, and also to provide a basis of comparison for subsequent numerical solutions. Numerical results to date include the generation of two preliminary grid systems for duct flows, and the initial application of PAB3D to the corresponding geometries, which are of the class tested experimentally.

Sepri, Paavo↗
NASA NTRS1991

Experimental study of boundary layer transition with elevated freestream turbulence on a heated flat plate

A detailed investigation to document momentum and thermal development of boundary layers undergoing natural transition on a heated flat plate was performed. Experimental results of both overall and conditionally sampled characteristics of laminar, transitional, and low Reynolds number turbulent boundary layers are presented. Measurements were acquired in a low-speed, closed-loop wind tunnel with a freestream velocity of 100 ft/s and zero pressure gradient over a range of freestream turbulence intensities (TI) from 0.4 to 6 percent. The distributions of skin friction, heat transfer rate and Reynolds shear stress were all consistent with previously published data. Reynolds analogy factors for R(sub theta) is less than 2300 were found to be well predicted by laminar and turbulent correlations which accounted for an unheated starting length. The measured laminar value of Reynolds analogy factor was as much as 53 percent higher than the Pr(sup -2/3). A small dependence of turbulent results on TI was observed. Conditional sampling performed in the transitional boundary layer indicated the existence of a near-wall drop in intermittency, pronounced at certain low intermittencies, which is consistent with the cross-sectional shape of turbulent spots observed by others. Non-turbulent intervals were observed to possess large magnitudes of near-wall unsteadiness and turbulent intervals had peak values as much as 50 percent higher than were measured at fully turbulent stations. Non-turbulent and turbulent profiles in transitional boundary layers cannot be simply treated as Blasius and fully turbulent profiles, respectively. The boundary layer spectra indicate predicted selective amplification of T-S waves for TI is approximately 0.4 percent. However, for TI is approximately 0.8 and 1.1 percent, T-S waves are localized very near the wall and do not play a dominant role in transition process.

Sohn, Ki-Hyeon↗
NASA NTRS1989

Results of correlations for transition location on a clean-up glove installed on an F-14 aircraft and design studies for a laminar glove for the X-29 aircraft accounting for spanwise pressure gradient

Results of correlative and design studies for transition location, laminar and turbulent boundary-layer parameters, and wake drag for forward swept and aft swept wings are presented. These studies were performed with the use of an improved integral-type boundary-layer and transition-prediction methods. Theoretical predictions were compared with flight measurements at subsonic and transonic flow conditions for the variable aft swept wing F-14 aircraft for which experimental pressure distributions, transition locations, and turbulent boundary-layer velocity profiles were measured. Flight data were available at three spanwise stations for several values of sweep, freestream unit Reynolds number, Mach numbers, and lift coefficients. Theory/experiment correlations indicate excellent agreement for both transition location and turbulent boundary-layer parameters. The results of parametric studies performed during the design of a laminar glove for the forward swept wing X-29 aircraft are also presented. These studies include the effects of a spanwise pressure gradient on transition location and wake drag for several values of freestream Reynolds numbers at a freestream Mach number of 0.9.

Goradia, S. H.↗
NASA NTRS1990

Effects of Wing Sweep on Boundary-layer Transition for a Smooth F-14A Wing at Mach Numbers from 0.700 to 0.825

The results are discussed of the variable sweep transition flight experiment (VSTFE). The VSTFE was a natural laminar flow experiment flown on the swing wing F-14A aircraft. The main objective of the VSTFE was to determine the effects of wing sweep on boundary layer transition at conditions representative of transport aircraft. The experiment included the flight testing of two laminar flow wing gloves. Glove 1 was a cleanup of the existing F-14A wing. Glove 2, not discussed herein, was designed to provide favorable pressure distributions for natural laminar flow at Mach number (M) 0.700. The transition locations presented for glove 1 were determined primarily by using hot film sensors. Boundary layer rake data was provided as a supplement. Transition data were obtained for leading edge wing sweeps of 15, 20, 25, 30, and 35 degs, with Mach numbers ranging from 0.700 to 0.825, and altitudes ranging from 10,000 to 35,000 ft. Results show that a substantial amount of laminar flow was maintained at all the wing sweeps evaluated. The maximum transition Reynolds number of 13.7 x 10(exp 6) was obtained for the condition of 15 deg of sweep, M = 0.800, and an altitude of 20,000 ft.

Anderson, Bianca Trujillo↗
NASA NTRS1991

Simulating boundary layer transition with low-Reynolds-number k-epsilon turbulence models. I - An evaluation of prediction characteristics. II - An approach to improving the predictions

The capability of two k-epsilon low-Reynolds number (LRN) turbulence models, those of Jones and Launder (1972) and Lam and Bremhorst (1981), to predict transition in external boundary-layer flows subject to free-stream turbulence is analyzed. Both models correctly predict the basic qualitative aspects of boundary-layer transition with free stream turbulence, but for calculations started at low values of certain defined Reynolds numbers, the transition is generally predicted at unrealistically early locations. Also, the methods predict transition lengths significantly shorter than those found experimentally. An approach to overcoming these deficiencies without abandoning the basic LRN k-epsilon framework is developed. This approach limits the production term in the turbulent kinetic energy equation and is based on a simple stability criterion. It is correlated to the free-stream turbulence value. The modification is shown to improve the qualitative and quantitative characteristics of the transition predictions.

Schmidt, R. C.↗
NASA NTRS1991

Mixing transition and the cascade to small scales in a plane mixing layer

Direct numerical simulations of time-developing plane mixing layers have been performed using a variety of initial conditions. Up to two pairings of the dominant spanwise rollers have been simulated. When the flow is sufficiently three-dimensional, a pairing can cause the mixing layer to undergo a transition to small-scale turbulence. This small-scale transition is accompanied by increased mixing of a passive scalar, similar to observations of the mixing transition in experiments. As part of the transition process, thin vortex sheets are generated by vortex stretching and roll up in a two-dimensional mixing layer. This higher-order rollup is part of the cascade to small-scale turbulence. Estimates are obtained for the degree of three-dimensionality required for the pairing to initiate the transition.

Moser, R. D.↗
NASA NTRS1990

Boundary-layer stability analysis of flight-measured transition data

Correlation of in-flight boundary-layer transition experiments with linear boundary-layer stability theory contributes both to the validation of the numerical methods as well as the analysis of the measured transition process. Transition results obtained in a recent flight experiment, in which the extent of laminar flow and the transition process on the wing of a business-jet fitted with an instrumented glove section were determined, are analyzed. The experiment was conducted at freestream Mach numbers from 0.55 to 0.82, chord Reynolds numbers from 10 to 20 x 10 to the 6th, and leading-edge sweep angles 17 deg to 20 deg. The growth of both Tollmien-Schlichting and crossflow instabilities are predicted using the e exp n method for several flight conditions and the calculated n-factors at transition onset are correlated. Comparison of the measured dominant boundary-layer disturbance frequencies and the predicted unstable frequencies shows fair agreement for several of the flight conditions studied.

Obara, Clifford J.↗
NASA NTRS1991

The use of transition heights for the representation of ion composition

Several characteristic transition heights can be found in ionospheric ion-composition profiles. These are the boundaries between the regions dominated by light ions, atomic oxygen ions, molecular ions, and cluster ions, respectively. Ion-composition modeling can benefit from the use of these transition heights. Special emphasis is given to the 'upper' transition height H sub T (light ions to atomic oxygen) and to the 'lower' transition height h sub t (atomic oxygen to molecular ions). Transition-height models deduced from rocket and satellite measurements are compared with the heights predicted by the International Reference Ionosphere. Considerable discrepancies are found between the different models as well as between the models and independent measurements.

Bilitza, Dieter↗
NASA NTRS1992

The effects of Venusian mantle convection with multiple phase transitions

Recently there was a flurry of activities in studying the effects of phase transitions in the Earth's mantle. From petrological and geophysical considerations, phase-transitions would also play an important role in venusian dynamics. The basic differences between the two planets are the surface boundary conditions, both thermally and mechanically. In this vein we have studied time-dependent mantle convection with multiple phase transitions and depth-dependent thermal expansivity (alpha is approximately rho(exp -6)), based on high-pressure and temperature measurements. Both the olivine-spinel and spinel-perovskite transitions were simulated by introducing an effective thermal expansivity, as described. Used together with the extended Boussinesq Approximation this method serves as a powerful tool to examine the effects of phase transitions on convection at relatively low computational costs.

Steinbach, V.↗
NASA NTRS1992

Modeling of near wall turbulence and modeling of bypass transition

The objectives for this project are as follows: (1) Modeling of the near wall turbulence: We aim to develop a second order closure for the near wall turbulence. As a first step of this project, we try to develop a kappa-epsilon model for near wall turbulence. We require the resulting model to be able to handle both near wall turbulence and turbulent flows away from the wall, computationally robust, and applicable for complex flow situations, flow with separation, for example, and (2) Modeling of the bypass transition: We aim to develop a bypass transition model which contains the effect of intermittency. Thus, the model can be used for both the transitional boundary layers and the turbulent boundary layers. We require the resulting model to give a good prediction of momentum and heat transfer within the transitional boundary and a good prediction of the effect of freestream turbulence on transitional boundary layers.

Yang, Z.↗