Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “test effectiveness”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17

Improved Heat Transfer and Volume Scaling through Novel Heater Design

In 2014, the University of California, Berkeley, Nuclear Engineering Thermal Hydraulics Laboratory completed construction of the Compact Integral Effects Test (CIET) facility, a scaled thermal hydraulics scaled integral effects test facility designed to model the Mark-1 pebble-bed fluoride-salt-cooled high-temperature reactor (Mk1 PB-FHR or simply Mk1). CIET uses an organic simulant fluid, Dowtherm A, to match the Prandtl, Reynolds, Froude, and Grashof numbers of important fluoride salt candidates for molten salt reactors, such as flibe. The FHR reactor core is simulated using a resistively heated tube, which heats the oil flowing through the annulus between the heated tube and a non-heated inner tube. However, the volume fraction of the coolant in the CIET heater was dramatically lower than the volume fraction of the primary coolant in the Mk1 PB-FHR design (3% in CIET vs. 17% in Mk1) because the CIET heater was initially scaled to match an earlier FHR design. Also, the maximum core heater power in CIET is limited by the melting point of Teflon components in CIET, approximately 330 deg. C. For conservatism, the CIET heater power is limited to keep the maximum surface temperature of the heater below 250 deg. C. At the nominal mass flow rate of 0.18 kg/s, this power was about 5 kW. A higher heat transfer coefficient from the heater wall to the oil was needed to increase the effective power delivered to the oil. In order to alleviate these two limitations, a new heater insert was designed and constructed for CIET. This new heater insert uses a twisted tape to augment heat transfer. The twisted tape is supported inside a perforated inner tube that has the same diameter as the original inner tube of the heater, in order to make it compatible with CIET's original heater design. The heat transfer and pressure drop properties of the new heater insert designs were tested in CIET and compared to the previous design in terms of pressure drop and convective heat transfer coefficient. The new heater inserts are intended to increase the range of power levels and mass flow rates that can be tested in CIET in order to augment understanding of FHR thermal hydraulic phenomena. Also, obtaining different data points for CIET response dynamics under different heater coolant residence times will be valuable in evaluating the Mk1 design.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Test report: effect of specimen orientation and location on the tensile properties of GTS forging 1472859

ASTM standardized tensile tests were performed on GTS WR-quality 1472859 forging (21-6- 9 material) to determine the dependence of tensile properties on specimen orientation (longitudinal vs. transverse) with respect to forging ‘grain flow’ and location within the forging. Statistical analyses of the results show that location has a statistically measurable effect on the longitudinal tensile properties (as compared to the error involved in tensile testing). However, this dependence of the properties with location, especially in the circumferential orientation, causes large variability in the results that clouds the statistical determination of any orientation effect. As a result, this forging is determined to be inhomogeneous along the forging length, with a significant range in properties observed (e.g. yield strengths from 85 to 117 ksi) and highest strength/lowest ductility in the spherical region. Additional specimens should be tested to acquire a higher resolution view of this inhomogeneity if the end use of the data is structural integrity analyses using spatially dependent properties; however, sufficient data is provided in this study to extract a statistical lower bound for conservative, homogeneous structural analysis.

36 MATERIALS SCIENCE↗

Tracking Radioactive Isotopes in HVAC and Application for Hot Cell Analyses - 20155

In recent years, the surge in the number of isotope production facilities under design has increased the need to analyze isotope migration in facility Heating, Ventilation, and Air Conditioning (HVAC) during normal operations and accident scenarios. These facilities are used to produce isotopes for medical, security, and industrial applications and as such are subject to license and regulatory requirements 10CFR20, 10CFR30, 10CFR50, and 10CFR70. GOTHIC, a general-purpose thermal-hydraulics software package, includes the ability to model isotopic tracers, radioactive decay and isotope migration as well as HEPA and charcoal filters for isotope retention. A GOTHIC model was developed by Zachry Nuclear Engineering (ZNE) to examine the effect of negative room pressure, HEPA filtration, and HVAC fluctuations on radiation areas, hot cells and gloveboxes. Radioactive tracers were used to simulate the concentration of spills within contaminated areas, track the migration of isotopes of interest, and determine the isotopic retention and buildup on facility HEPA filters. A variety of isotopes with concern to dose (e.g., Kr-85, Sr-90, I-131, etc.), including their decay and progeny, are included in the analysis. Negative pressures are maintained in the regions of interest by a representative central HVAC system equipped with a volumetric fan that exhausts to the environment after a series of isolation valves and HEPA filters. GOTHIC is an industry trusted tool for providing engineering solutions for a variety of applications, including fission product tracking, aerosol and particulate transport and ventilation assessments. The software provides an integrated analysis environment that includes a graphical user interface (GUI) for constructing analysis models, a numerical solver that includes parallel processing capabilities and a post-processor for evaluating simulation results. It solves the conservation equations for mass, momentum and energy for multicomponent, multi-phase flow in lumped parameter and multi-dimensional geometries (1, 2, or full 3D), including the effects of turbulence, diffusion and buoyancy. It has been developed and maintained under a Quality Assurance program in compliance with the requirements of 10CFR50 Appendix B and applicable portions of ASME NQA-1 since 1995. GOTHIC has been used for assessing both forced and natural convection conditions for a wide range of applications, including: - Tracking concentration of hazardous gases and chemicals for habitability and safety assessments - Determining ventilation and filtration requirements and optimizing location and arrangement of these systems - Room heat-up, including diverse and Flexible coping strategies for Extended Loss of AC Power (FLEX/ELAP) - Equipment Qualification (EQ) A distinctive feature of GOTHIC is the ability to track many different fields/substances in a simulation, including user defined tracer elements, in the liquid, vapor and droplet fields as well as surfaces and filters. This capability allows GOTHIC to model fission product transport and release or the removal of particulates or harmful toxins from exhaust gases using a spray scrubber or other types of filtration systems. GOTHIC also includes models for engineered equipment, such as fans, filters, charcoal filters, dryers/demisters, dampers, etc. The aerosols and other filtered material are removed or accumulated in these components. The range of aerosol and radiological applications that GOTHIC has been used for includes: - Source Term: Primary Coolant (Equilibrium) Activity; Non-Water Coolant Source/Leakage. - Conditions for Iodine Re-evolution: Sump/Suppression Pool Conditions and pH; - RWST Conditions and pH. - Isotope Removal Mechanisms: Containment Sprayed and Unsprayed Region Mixing; Charcoal Filter Heating due to Iodine decay. - Radionuclide Transport and Decay: Post-LOCA Release in containment; Transport between connected Compartments and vent systems; Groundwater transport of radionuclides. - Non-Newtonian Fluid modeling for sludge, waste tanks, etc. ADAMS ML071581053 (titled 'Best Practice Guidelines for the use of CFD in Nuclear Reactor Safety Applications') poses guidelines for applying single phase CFD codes in nuclear reactor safety problems and GOTHIC is listed as a 'tool for 3D flows' and 'dispersal and deposition of radionuclides.' The Nuclear Quality Assurance (NQA) pedigree of GOTHIC is an important aspect for applications in the nuclear industry. The fundamental tracer models (convective transport, molecular and turbulent diffusion, removal mechanisms, etc.) have been verified using analytical solutions and validated against applicable separate effects tests. Also, GOTHIC has been benchmarked to many integrated effects tests, including Phebus FP (Fission Product). GOTHIC gives good agreement for the buildup and decay of fission products in Phebus Test 3. The model developed by ZNE demonstrates GOTHIC's applicability and acceptability for use in analyzing the migration and retention of radioactive isotopes and their progeny in normal operation and accident scenario analyses for isotope production facilities, hot cells, and gloveboxes. The tracer activities calculated by GOTHIC can then be used in downstream radiation transport and shielding codes like RADTRAD-NAI{sup C}, MCNP{sup R}, and MicroShield{sup R} to determine on-site and of-site doses. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Single Event Effects (SEE) Testing of Embedded DSP Cores within Microsemi RTAX4000D Field Programmable Gate Array (FPGA) Devices

Motivation for this work is: (1) Accurately characterize digital signal processor (DSP) core single-event effect (SEE) behavior (2) Test DSP cores across a large frequency range and across various input conditions (3) Isolate SEE analysis to DSP cores alone (4) Interpret SEE analysis in terms of single-event upsets (SEUs) and single-event transients (SETs) (5) Provide flight missions with accurate estimate of DSP core error rates and error signatures.

Perez, Christopher E.↗

Testing the Effects of Helium Pressurant on Thermodynamic Vent System Performance with Liquid Hydrogen

In support of the development of a zero gravity pressure control capability for liquid hydrogen, testing was conducted at the Marshall Space Flight Center using the Multipurpose Hydrogen Test Bed (MHTB) to evaluate the effects of helium pressurant on the performance of a spray bar thermodynamic vent system (TVS). Fourteen days of testing was performed in August - September 2005, with an ambient heat leak of about 70-80 watts and tank fill levels of 90%, 50%, and 25%. The TVS successfully controlled the tank pressure within a +/- 3.45 kPa (+/- 0.5 psi) band with various helium concentration levels in the ullage. Relative to pressure control with an "all hydrogen" ullage, the helium presence resulted in 10 to 30 per cent longer pressure reduction durations, depending on the fill level, during the mixing/venting phase of the control cycle. Additionally, the automated control cycle was based on mixing alone for pressure reduction until the pressure versus time slope became positive, at which time the Joule-Thomson vent was opened. Testing was also conducted to evaluate thermodynamic venting without the mixer operating, first with liquid then with vapor at the recirculation line inlet. Although ullage stratification was present, the ullage pressure was successfully controlled without the mixer operating. Thus, if vapor surrounded the pump inlet in a reduced gravity situation, the ullage pressure can still be controlled by venting through the TVS Joule Thomson valve and heat exchanger. It was evident that the spray bar configuration, which extends almost the entire length of the tank, enabled significant thermal energy removal from the ullage even without the mixer operating. Details regarding the test setup and procedures are presented in the paper. 1

Flachbart, R. H.↗

Droplet Entrainment in Steam Supply System of Water-Cooled Small Modular Reactors: Experiment and Modeling Approaches

Droplet entrainment in steam-flow is a prominent phenomenon that needs adequate safety and risk analysis of postulated transient and accident scenarios—including experimental investigation and representative modeling and simulation (M&S)—for small modular reactor (SMR) system design and demonstration. This study identifies knowledge gaps by evaluating experimental and computational fluid dynamics modeling approaches to support early-stage reactor system design, testing, and model evaluation. Previous studies reported in the literature for steam-flow entrainment primarily focused on gigawatt capacity pressurized water reactor (PWR) systems. However, entrainment phenomena are even more prominent for PWR-type SMRs due to their more compact integrated designs, which need further research and development. To fill the research gaps, this study provides insight by specifying the phenomena of interest by leveraging the lessons learned from past research, adopting advanced M&S techniques and advanced instrumentation and control. The findings and recommendations are applicable for evaluating steam-flow entrainment models and for designing integral effect test and separate effect test facilities for gaining reactor design approvals.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Determination of Ground Effect from Tests of a Glider in Towed Flight

Report presents the results of an investigation made to find the effect of ground on the aerodynamic characteristics of a Franklin PS-2 glider. The lift, the drag, and the angle of attack of the glider in towed flight were determined at several heights from 0.14 to 1.19 span lengths and at various speeds for each height. Two wing arrangements were tested: the plain wing, and the wing with a nearly full-span 30-percent-chord split flap deflected 45 degrees. The experimental results for the plain wing were in good agreement with theoretical values calculated by the method of Wieselsberger for both the angle of attack and the drag coefficient at a height of 0.21 span length; Tani's refinements of the theory had a practically negligible effect on the computed values in this case.

Wetmore, J W↗

Vorago RH-OBC-1 Single Event Effect Characterization Test Report

The Vorago Technologies RH-OBC-1 is a CubeSat Kit Bus compatible single board computer with a Vorago VA10820 ARM Cortex-M0 microcontroller at its core. The board also includes a set of common peripheral integrated circuits, like voltage regulators, non-volatile memories (NVM), an analog-to-digital converter (ADC), a watchdog/supervisor, and a Controller Area Network (CAN) bus transceiver. High-energy proton (200 MeV) testing was conducted at both board and component levels to investigate single-event effects.

CubeSat compatible board↗

Development of a characterization methodology for post-irradiation examination of miniature fuel specimens

The miniature fuel (MiniFuel) irradiation experimental design at Oak Ridge National Laboratory (ORNL) enables benchmark testing and separate effects testing of novel fuel types in the High Flux Isotope Reactor (HFIR) in support of the Advanced Fuels Campaign (AFC). The first round of MiniFuel sub-capsules will be available for post-irradiation examination at the end of 2018. This report establishes the procedure for disassembly, fuel retrieval, post-irradiation analysis of the fission product behavior (fission gas release and fuel swelling), and microstructural characterization of the irradiated MiniFuel specimens. All methods were tested and validated out-of-cell and are ready to be implemented in-cell for use on the first set of irradiated MiniFuel specimens. The path forward regarding further characterization techniques is presented, which will involve analyzing other specimen geometries using the methods presented in this report and expanding the post-irradiation analysis of MiniFuel specimens to include additional properties.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Status report and preliminary results of the spacecraft control laboratory experiment

The Spacecraft Control Laboratory Experiment (SCOLE) was conceived to provide a physical test bed for investigation of control techniques for large flexible spacecraft. The SCOLE problem is defined as two design challenges. The first challenge is to design control laws for a mathematical model of a large antenna attached to the space shuttle by a long flexible mast. The second challenge is to design and implement a control scheme on a laboratory representation of the structure modelled in the first part. Control sensors and actuators are typical of those which the control designer would have to deal with on an actual spacecraft. The primary control processing computer is representative of the capacity and speed which may be expected in actual flight computers. A brief description is given of the laboratory apparatus along with some preliminary results of structural dynamics tests and actuator effectiveness tests.

Williams, Jeffrey P.↗

Thermal Protection Materials Technology for NASA's Exploration Systems Mission Directorate

To fulfill the President s Vision for Space Exploration - successful human and robotic missions between the Earth and other solar system bodies in order to explore their atmospheres and surfaces - NASA must reduce trip time, cost, and vehicle weight so that payload and scientific experiment capabilities are maximized. As a collaboration among NASA Centers, this project will generate products that will enable greater fidelity in mission/vehicle design trade studies, support risk reduction for material selections, assist in optimization of vehicle weights, and provide the material and process templates for development of human-rated qualification and certification Thermal Protection System (TPS) plans. Missions performing aerocapture, aerobraking, or direct aeroentry rely on technologies that reduce vehicle weight by minimizing the need for propellant. These missions use the destination planet s atmosphere to slow the spacecraft. Such mission profiles induce heating environments on the spacecraft that demand thermal protection heatshields. This program offers NASA essential advanced thermal management technologies needed to develop new lightweight nonmetallic TPS materials for critical thermal protection heatshields for future spacecraft. Discussion of this new program (a December 2004 new start) will include both initial progress made and a presentation of the work to be preformed over the four-year life of the program. Additionally, the relevant missions and environments expected for Exploration Systems vehicles will be presented, along with discussion of the candidate materials to be considered and of the types of testing to be performed (material property tests, space environmental effects tests, and Earth and Mars gases arc jet tests).

Valentine, Peter G.↗

Test Medium Effects on Ignition, Combustion and Flameholding Processes in Scramjet Combustors

The total temperatures (enthalpies) required to ground-test air-breathing (aero-propulsion) engines at high Mach number flight conditions can be achieved in a number of ways. Among these are: 1. Heat exchangers, including pre-heated ceramic beds. 2. direct electrical heating, e.g., arc discharge and resistance heaters. 3. Compression heating. 4. Shock heating, and 5. In-stream combustion, with oxygen replenishment to match air content. Each method has distinct advantages, disadvantages and limitations. All have a common characteristic of being designed for intermittent flow, due to the extreme energy required for continuous operation at simulated Mach numbers above about 3. All also distort the composition of atmospheric air to some degree, due to the high temperatures that occur in the plenum section prior to expansion of the flow to simulated flight conditions. In the case of in-stream combustion, the resulting test medium is commonly referred to as "vitiated air", being composed of oxygen, nitrogen and some fraction of combustion products.

Chinitz, W.↗

Effects of test facility contaminants on supersonic hydrogen-air diffusion flames

Results are presented from an analytical assessment of the effects of NO and H2O in air on the ignition and reaction of hydrogen. Three flow models of the burning process were used, each including a 32 reaction chemistry mechanism. These models were a plug flow reactor to determine ignition and reaction times; a well-stirred reactor to assess flame stability or blow-off; and a parabolic Navier-Stokes code to examine the diffusion flame combustion. The diffusion flame was computed for a cold supersonic H2 jet coaxial with a supersonic air stream at a static temperature of 1100 K and a pressure of 1 atmosphere.

Rogers, R. Clayton↗

Effects of test facility contaminants on supersonic hydrogen-air diffusion flames

Results are presented from an analytical assessment of the effects of NO and H2O in air on the ignition and reaction of hydrogen. Three flow models of the burning process were used, each including a 32 reaction chemistry mechanism. These models were a plug flow reactor to determine ignition and reaction times; a well-stirred reactor to assess flame stability or blow-off, and a parabolic Navier Stokes code to examine the diffusion flame combustion. The diffusion flame was computed for a cold supersonic H2 jet coaxial with a supersonic air stream at a static temperature of 1100 K and a pressure of 1 atmosphere.

Rogers, R. Clayton↗

Proton Single Event Effects (SEE) Testing of the Myrinet Crossbar Switch and Network Interface Card

As part of the Remote Exploration and Experimentation Project (REE), work was performed to do a proton SEE (Single Event Effect) evaluation of the Myricom network protocol system (Myrinet). This testing included the evaluation of the Myrinet crossbar switch and the Network Interface Card (NIC). To this end, two crossbar switch devices and five components in the NIC were exposed to the proton beam at the University of California at Davis Crocker Nuclear Laboratory (CNL).

Howard, James W., Jr.↗

Method for Real-Time Salt Aerosol Concentration and Size Measurements for Molten Salt Reactor Safety Assessments

Licensing a new nuclear reactor involves evaluating credible accident scenarios by developing models that simulate accident progression to predict possible outcomes and their impact on safety. The formation of radionuclide-bearing aerosols in the respirable size range can significantly affect dose consequence and threaten human health and is therefore a focus of nuclear reactor safety assessments. Recent reviews of the literature identified a lack of existing experimental data describing the mechanisms of formation and properties (size, concentration, and composition) of radionuclide-bearing aerosols that may be produced from molten salt reactor (MSR) facilities during postulated accident scenarios. Experiments on aerosol formation from molten salt systems are a high priority need that will support MSR licensing by indicating the radiological consequences of aerosol formation and providing the data required for model development and validation. The evolving conditions that occur during a MSR accident, such as a spill of molten fuel salt, may affect aerosol formation mechanisms and aerosol properties over time. There is a need to conduct experiments that simulate credible MSR accidents in a laboratory to generate aerosols with realistic characteristics and behaviors and a need to measure these aerosols in real time under accident-relevant conditions. This report describes the development of a method that can be used to quantify the size and concentration of salt aerosol particles that form from molten salt systems in real time. This method will be employed in future integral effects tests that are conducted at an engineering scale to simulate realistic MSR accidents and in future separate effects tests that will provide mechanistic insight into aerosol formation and properties to support process model development.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗