Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “sintering”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
DOE OSTI2018

Phase evolution during spark plasma sintering of novel Si3N4-doped TiB2–SiC composite

Highlights: • The effect of Si{sub 3}N{sub 4} addition on microstructure of TiB{sub 2}–SiC composite was studied. • Fully dense TiB{sub 2}-based composite was obtained by addition of SiC and Si{sub 3}N{sub 4}. • TiC, B{sub 4}C and SiO{sub 2} were formed in Si{sub 3}N{sub 4}-free and Si{sub 3}N{sub 4}-doped TiB{sub 2}–SiC ceramics. • TiN and BN were in-situ formed only in Si{sub 3}N{sub 4}-doped TiB{sub 2}–SiC sample. - Abstract: Spark plasma sintering process was employed to fabricate TiB{sub 2}–SiC and novel Si{sub 3}N{sub 4}-doped TiB{sub 2}–SiC ceramic composites at 1900 °C for 7 min under 40 MPa. The microstructural development of TiB{sub 2}-based composites was significantly influenced by the addition of SiC as a reinforcement phase and Si{sub 3}N{sub 4} as a sintering aid. Thermodynamic assessment, X-ray diffractometry, scanning electron microscopy and energy dispersive spectroscopy disclosed the in-situ formation of TiC, B{sub 4}C and SiO{sub 2} in both samples as well as TiN and BN in the Si{sub 3}N{sub 4}-doped TiB{sub 2}–SiC sample through the chemical reactions of SiC and Si{sub 3}N{sub 4} additives with the surface oxide impurities of TiB{sub 2} particles (TiO{sub 2} and B{sub 2}O{sub 3}). The elimination of harmful oxide layers and the in-situ formation various secondary phases had remarkable influences on the sinterability and final microstructure of TiB{sub 2}.

36 MATERIALS SCIENCE↗
DOE OSTI2021

On the Arrhenius-like behavior of conductivity during flash sintering of 3 mol% yttria stabilized zirconia ceramics

Here, we discuss the Arrhenius behavior of electrical conductivity σ during flash sintering of 3 mol% yttria stabilized zirconia (3YSZ). In situ x-ray diffraction is used to determine sample temperature. Sintering contribution to σ is excluded by investigating the flash event on a dense ceramic. We show that total conductivity follows an Arrhenius-like equation in both dense and green samples, even during Stage II of flash. The non-linearity often verified during flash sintering of 3YSZ is therefore related to the furnace temperature instead of the sample temperature when building the ln(σ) vs. 1/T plots. Furthermore, we verified a change in the activation energy for conduction prior to the ignition of the flash event and discussed the possible mechanisms. For instance, the decrease in activation energy from Stage I to II in the dense sample is attributed to a contribution from electronic carriers.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Ultrafast Reactive Laser Sintering of Highly Conductive Garnet-Type LLZTO Solid Electrolytes

Rapid and scalable fabrication of garnet-type solid electrolytes remains a major challenge for the practical deployment of lithium metal batteries. Here, we report reactive laser sintering (RLS) as an ultrafast and potentially scalable strategy for fabricating garnet-type Li 6.4 La 3 Zr 1.4 Ta 0.6 O 12 (LLZTO) solid electrolytes. RLS of LLZTO enables simultaneous reaction and densification, achieving ∼95% relative density while minimizing lithium loss and suppressing secondary phase formation. Compared to conventional furnace sintering, RLS promotes enhanced grain growth and improved densification, leading to improved ionic conductivity (0.36 ± 0.08 mS cm −1 ) while maintaining comparable activation energies for Li + transport. Structural characterization by X-ray diffraction (XRD), Raman spectroscopy, and solid-state 6 Li/ 7 Li NMR confirms the formation of cubic garnet LLZTO with homogeneous microscale elemental distribution. In addition, nanoindentation measurements demonstrate that RLS preserves the mechanical properties of the garnet framework despite ultrafast localized thermal processing. By integrating simultaneous reaction and densification with tunable microstructural control, reactive laser sintering provides a promising manufacturing pathway for high-performance garnet solid electrolytes toward next-generation solid-state batteries.

CO2 laser↗
DOE OSTI2024

Surface Self-Diffusion Induced Sintering of Nanoparticles

Despite the critical role of sintering phenomena in constraining the long-term durability of nanosized particles, a clear understanding of nanoparticle sintering has remained elusive due to the challenges in atomically tracking the neck initiation and discerning different mechanisms. Through the integration of in situ transmission electron microscopy and atomistic modeling, this study uncovers the atomic dynamics governing the neck initiation of Pt–Fe nanoparticles via a surface self-diffusion process, allowing for coalescence without significant particle movement. Real-time imaging reveals that thermally activated surface morphology changes in individual nanoparticles induce significant surface self-diffusion. Further, the kinetic entrapment of self-diffusing atoms in the gaps between closely spaced nanoparticles leads to the nucleation and growth of atomic layers for neck formation. This surface self-diffusion-driven sintering process is activated at a relatively lower temperature compared to the classic Ostwald ripening and particle migration and coalescence processes. The fundamental insights have practical implications for manipulating the morphology, size distribution, and stability of nanostructures by leveraging surface self-diffusion processes.

36 MATERIALS SCIENCE↗
DOE OSTI2016

Effect of sintering temperatures and screen printing types on TiO{sub 2} layers in DSSC applications

Dye-Sensitized Solar Cell (DSSC) is a candidate solar cell, which has a big potential in the future due to its eco-friendly material. This research is conducted to study the effect of sintering temperature and the type of screen-printing toward the characteristics of TiO{sub 2} layer as a working electrode in DSSC. TiO{sub 2} layers were fabricated using a screen-printing method with a mesh size of T-49, T-55, and T-61. TiO{sub 2} layers were sintered at temperatures of 600°C and 650°C for 60 min. DSSC structure was composed of TiO{sub 2} as semiconductors, ruthenium complex as dyes, and carbon as counter electrodes. The morphology of TiO{sub 2} layer was observed by using Nikon E2 Digital Camera Microscopy. The efficiencies of DSSC were calculated from the I-V curves. The highest efficiency is 0.015% at TiO{sub 2} layer fabricated with screen type T-61 and at a sintering temperature of 650°C.

14 SOLAR ENERGY↗
DOE OSTI2016

Sintering time effect on crystal structure and magnetic properties of Bi{sub 0.8}La{sub 0.2}FeO{sub 3} multiferroics

Effect of sintering time over the structure and magnetic properties has been studied in Bi{sub 0.8}La{sub 0.2}FeO{sub 3} multiferroic ceramics prepared by solid state reaction technique. The structure changes with the advent mixed phase rhombohedral and orthorhombic symmetry to immaculate orthorhombic structure with sintering time from 2 to 3 hour, as revealed by means of the simulation of XRD patterns via Rietveld analysis through FullProf software. The M – H plots depict decent enhancement in magnetization with values of remnant magnetization (Mr) from 0.01868emu/g to 0.09357emu/g while the sintering time is varied from 2 to 3 hour. The metamagnetic transition may be attributed to the crumpling of the modulated spin cycloid existing inherently in the pristine compound. The presented study may have considerable impact in commercial as well as advanced electronic applications.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2016

Effect of sintering treatment on structural and magnetic properties of Ni{sub 0.5}Co{sub 0.5}Fe{sub 2}O{sub 4} ferrites

Two sets of Ni{sub 0.5}Co{sub 0.5}Fe{sub 2}O{sub 4} ferrites were synthesized using sol-gel method. Both the samples were heat treated at different temperatures. The effect of sintering treatment analyzed on structural and magnetic properties. X-ray diffraction (XRD) and scanning electron microscope (SEM) were used for structural analysis. Alternating gradient magnetometer (AGM) is used for magnetic measurements. In structural analysis, grains size is calculated using Debye - Scherrer’s formula and Williamson-Hall (W-H) plot. From both the techniques, grain size is found nearly same and increased in size with increase sintering temperature. Increased particle size is confirmed from SEM micrographs. Strain value is calculated from intercept of W-H plot. In both the samples, compressive strain in nature is found. Magnetic properties were also varying under different heat treatment. The change in magnetic properties with change in structural change at different sintering treatment is discussed in this report.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2016

The effects of composition and sintering temperature on the silica foam fabricated by slurry method

Reticulated ceramic or open pore ceramic foam is a well-known material which exhibits extremely high porosities, with a significant degree of interconnectivity that makes them desirable in a wide range of applications. There were broad types of ceramic foam fabrication method such as polymeric sponge method, direct foaming, and starch consolidation. In this study, the slurry method has been chosen to fabricate Silica (SiO{sub 2}) foam. In this process, Polyurethane (PU) foam template was dipped into ceramic slurry and followed by drying and sintering to obtain foam which contains porosity in the range of 50% to 70%. The compositions of SiO{sub 2} were varied starting from 55 wt.%, 60 wt.%, 65 wt.% and 70 wt.%. The samples of SiO{sub 2} that have been dipped and dried were sintered at 900°C, 1000°C, 1100°C, and 1250°C. The sintered SiO{sub 2} ceramic foam samples were characterized to observe their morphology, and physical properties. Thus, the microstructure of the SiO{sub 2} ceramic foams samples was examined by Scanning Electron Microscopy (SEM), and Electron Dispersive Spectroscopy (EDS). Meanwhile, the physical properties of the SiO{sub 2} ceramic foam samples such as the total porosity (%) and bulk density were determined using Archimedes method. It was found that the density of ceramic foam produced was in the range of 0.25 g/cm{sup 3} up to 0.75 g/cm{sup 3}, whereas the level of porosity percentage was in the range of 61.81% to 82.18% with the size of open pore or window cells were in between 141 µm up to 626 µm.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Reliability Analysis of Large-Area, Low Pressure-Assisted Silver Sintering for Medium-Voltage Power Modules

Multi-layer insulating ceramic substrates can enable medium-voltage (MV) power modules with reduced peak electric field. This benefit is particularly important for MV silicon carbide (SiC) MOSFETs due to their higher operating voltages. Large-area, low-pressure assisted silver sintering is a potential solution for bonding substrates to create a multi-layer structure. The voiding content and defect density of the bond used to create the multi-layer substrate stack-up is critical to the reliability of the power module and the thermal performance, as this bond is in the primary path for heat dissipation in the power module structure. Here, samples of two-layer direct bonded aluminum (DBA) stacks have been fabricated and subjected to thermal cycling to analyze their reliability. Passive thermal cycling from -40 degrees C to 200 degrees C was performed. Cross-sections were cut at pre-determined intervals and imaged with Scanning Electron Microscopy (SEM). After 1000 thermal cycles, adhesive failures are observed between the sintered silver and the DBA surface. Cross-sections were cut and imaged via optical microscope and SEM. Thermal analyzer measurements are recorded on a 10-kV SiC power module utilizing the sintered DBA substrate stacks.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2023

Pressureless sintering of dual-phase, high-entropy boride–carbide ceramics

Here, dual-phase, high-entropy boride–carbide ceramics were densified by pressureless sintering. Relative densities up to approximately 96% were obtained for ceramics containing about 30 vol% high-entropy boride and 70 vol% high-entropy carbide. Isostatic pressing at 200 MPa resulted in higher relative densities of both the green bodies and final ceramics compared to uniaxial pressing. The highest relative density of 96.3% was achieved for a ceramic that was isostatically pressed at 200 MPa and sintered at 2300°C for 2 h. Grain sizes of the resulting ceramics were approximately 2 µm. This is the first report of pressureless sintering of dual-phase, high-entropy boride–carbide ceramics.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Effect of the Sintering Temperature on the Formation of Ferroelectric Properties of a Lead Zirconate–Titanate Ceramic

Effect of the sintering temperature on the formation of the microstructure, the domain structure, and the ferroelectric properties of a lead zirconate–titanate Pb(Ti{sub x}Zr{sub 1–} {sub x})O{sub 3} piezoelectric ceramics has been studied. It is shown that the ferroelectric phase forms at a sintering temperature of 860°C. At higher sintering temperatures, the main effect on the properties is due to a unit cell deformation and free charge carriers.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2019

Spark Plasma Sintering of SmS-Based Ceramic Targets for the Magnetron Sputtering

The results of studying the electric-spark plasma sintering of samarium monosulfide ceramics are presented. The dependence of the microstructure and phase composition of ceramics on the temperature of spark plasma sintering is studied on the basis of the data of scanning electron microscopy, energy dispersion X-ray microanalysis, and powder X-ray diffraction of synthesized samples. It is shown that a dense, nonporous ceramics, the phase composition of which is close to the composition of the initial powder, is formed at a sintering temperature of 1200°C.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2020

"Sintering" Models and In-Situ Experiments: Data Assimilation for Microstructure Prediction in SLS Additive Manufacturing of Nylon Components

Selective laser sintering methods are workhorses for additively manufacturing polymer-based components. The ease of rapid prototyping also means it is easy to produce illicit components. It is necessary to have a data-calibrated in-situ physical model of the build process in order to predict expected and defective microstructure characteristics that inform component provenance. Toward this end, sintering models are calibrated and characteristics such as component defects are explored. This is accomplished by assimilating multiple data streams, imaging analysis, and computational model predictions in an adaptive Bayesian parameter estimation algorithm. From these data sources, along with a phase-field model, bulk porosity distributions are inferred. Model parameters are constrained to physically-relevant search directions by sensitivity analysis, and then matched to predictions using adaptive sampling. Using this feedback loop, data-constrained estimates of sintering model parameters along with uncertainty bounds are obtained.

3D printing, Additive Manufacturing, polymer, sint↗
DOE OSTI2016

Microstructure and microchemistry of flash sintered K 0.5 Na 0.5 NbO 3

In this paper, flash sintering experiments were performed, for the first time, on sodium potassium niobate (KNN) ceramics. A theoretical density of 94% was achieved in 30 s under 250 V/cm electric-field at 990°C. These conditions are ~100°C lower and faster than the conventional sintering conditions. Grains tended to grow after 30 s. flash sintering duration under constant electric-field. Detailed microstructural and chemical investigations of the sample showed that there was inhomogenous Na, K distribution and it resembles a core–shell structure where K is more in the shell and Na is more in the core region. The inhomogenous distribution of Na and K was correlated with the doubling of the unit cell within the grain along 002 direction. Compositional equilibrium is achieved after a heat treatment at 1000°C for 4 h. Finally, the compositional variations appeared to have been linked to grain boundary melting during flash and consequent recrystallization as the sample cooled.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Simultaneous Spark Plasma Sintering of Multiple Complex Shapes

This work addresses the two great challenges of the spark plasma sintering (SPS) process: The sintering of complex shapes and the simultaneous production of multiple parts. A new controllable interface method is employed to concurrently consolidate two nickel gear shapes by SPS. A graphite deformable sub-mold is specifically designed for the mutual densification of both complex parts in a unique 40 mm powder deformation space. An energy efficient SPS configuration is developed to allow the sintering of a large-scale powder assembly under electric current lower than 900 A. The stability of the developed process is studied by electro-thermal-mechanical (ETM) simulation. The ETM simulation reveals that homogeneous densification conditions can be attained by inserting an alumina powder at the sample/punches interfaces, enabling the energy efficient heating and the thermal confinement of the nickel powder. Finally, the feasibility of the fabrication of the two near net shape gears with a very homogeneous microstructure is demonstrated.

36 MATERIALS SCIENCE↗
NASA NTRS2014

Sintering Characteristics of Multilayered Thermal Barrier Coatings Under Thermal Gradient and Isothermal High Temperature Annealing Conditions

Pyrochlore oxides have most of the relevant attributes for use as next generation thermal barrier coatings such as phase stability, low sintering kinetics and low thermal conductivity. One of the issues with the pyrochlore oxides is their lower toughness and therefore higher erosion rate compared to the current state-of-the-art TBC material, yttria (6 to 8 wt%) stabilized zirconia (YSZ). In this work, sintering characteristics were investigated for novel multilayered coating consisted of alternating layers of pyrochlore oxide viz Gd2Zr2O7 and t' low k (rare earth oxide doped YSZ). Thermal gradient and isothermal high temperature (1316 C) annealing conditions were used to investigate sintering and cracking in these coatings. The results are then compared with that of relevant monolayered coatings and a baseline YSZ coating.

Thermal Barrier Coatings↗
NASA NTRSDate not supplied

Vacuum Sintering of Highland Simulant CSM-LHT-1G

Sintering of lunar regolith is a process of interest to consolidate the ubiquitous granular material in durable structures on the lunar surface such as platforms, landing/launch pads, roads, and foundations for long-term robotic and human activities. Many publications do not report quantitative assessment of the effects of processing conditions on the strength properties of the sintered products. The work presented is an investigation into such effects on a carefully selected simulant, CSM-LHT-1G prepared for high temperature processing to eliminate undesired components that would not be present from lunar materials. Careful experiments under vacuum were conducted to identify the relevant factors that dominate the properties and the quality of the sintered product. CSM-LHT-1G simulant is a variant of the CSM-LHT-1 lunar highland simulant produced by Colorado School of Mines. The original mineralogical composition of CSM-LHT-1 (70 wt.% Greenspar, 30 wt.% Merriam Crater basalt) was modified to obtain a 30 wt.% glass content with the addition of NU-LHT-5M glass balanced with pyroxene (augite) to yield CSM-LHT-1G.

Vacuum Sintering↗
DOE OSTI2017

Thermomechanical Modeling of Sintered Silver - A Fracture Mechanics-based Approach: Extended Abstract: Preprint

Sintered silver has proven to be a promising candidate for use as a die-attach and substrate-attach material in automotive power electronics components. It holds promise of greater reliability than lead-based and lead-free solders, especially at higher temperatures (less than 200 degrees Celcius). Accurate predictive lifetime models of sintered silver need to be developed and its failure mechanisms thoroughly characterized before it can be deployed as a die-attach or substrate-attach material in wide-bandgap device-based packages. We present a finite element method (FEM) modeling methodology that can offer greater accuracy in predicting the failure of sintered silver under accelerated thermal cycling. A fracture mechanics-based approach is adopted in the FEM model, and J-integral/thermal cycle values are computed. In this paper, we outline the procedures for obtaining the J-integral/thermal cycle values in a computational model and report on the possible advantage of using these values as modeling parameters in a predictive lifetime model.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗