Results for “simulated current” — Page 17

NASA NTRSDate not supplied

Verification of Anisotropic Mesh Adaptation for Complex Aerospace Applications

The stabilized finite element solver, FUN3D-SFE, along with the grid mechanics package refine are verified for aerospace applications of laminar and turbulent flow simulations. The current verification exercise represents an extension of previous research using FUN3D-SFEwith adjoint-based mesh adaptation to generate highly anisotropic adapted meshes for inviscid problems. Adaptations are performed using a solution-based approach that controls the Lpnorm of Mach number interpolation error and an adjoint-based approach that controls the error in some output functional. Adaptive results are shown for laminar subsonic flow over a delta wing, laminar subsonic flow over ONERA M6 wing, inviscid supersonic flow over a sonic boom test case, and a turbulent flow over a high lift configuration (JAXA Standard Model). Mesh convergence results are also compared with results from FUN3D-FV (Finite Volume) whenever available. For all test cases considered, FUN3D-SFE gives significantly better accurate results than FUN3D-FV on coarse meshes.

Aravind Balan↗

NASA NTRSDate not supplied

TPSAS-NF1676L-33626-DND

NASA is conducting a series of computational experiments to quantify atmospheric effects on low noise sonic booms. In the current study, simulated cruise nearfield pressure data from NASA?s X-59 Quiet Supersonic Technology aircraft was propagated from the aircraft to the ground at four cardinal headings through five years of realistic atmospheric profiles at 30 locations across the eastern USA. Statistical design of experiments was used to select the locations where primary sonic thump carpet widths (CW) and metric levels at the ground were computed. Atmospheric profiles were taken from the Climate Forecast System Reanalysis database, which contains reanalyzed atmospheric profiles four times daily. Decision tree analyses were performed to determine relative importance of predictors for CW and metric levels. Predictors included were latitude, longitude, date, time of day, season, climate, aircraft heading, and ground elevation. Results of this study indicate the propagation resolution needed to adequately characterize the distributions of CW and ground metric data, i.e., necessary separation distance between propagation locations and total number of atmospheres through which to propagate. This resolution will be used for a follow-on study of simulated X-59 carpets across the entire US mainland.

Will Doebler↗

NASA NTRSDate not supplied

Vision 2030 Aircraft Propulsion Grand Challenge Problem: Full-engine CFD Simulations with High Geometric Fidelity and Physics Accuracy

2014 NASA published the outcome of the 2030 CFD (Computational Fluid Dynamics) Vision study: “CFD Vision 2030: A path to Revolutionary Computational Aerosciences” . The study provided a comprehensive review of the state of the art of CFD in 2014 for aerospace applications including, but not limited to, numerical algorithms, physics models, MDAO (Multidisciplinary Design Analysis and Optimization) and HPC (High Performance Computing) hardware. The study also proposed four conceptual ideas of Grand Challenge problems that would build on and benefit from advances outlined in the roadmap. The proposed challenges were meant to foster more detailed descriptions of grand challenge problems for specific disciplines. One of the proposed challenges was in the gas turbine propulsion area, focusing on transient full engine simulations. The current paper addresses detailed technical aspects of that challenge, and proposes a plan to approach it in a gradual manner, which includes high fidelity modeling of components, component coupling, and targeted experimental campaigns relying on common research models.

turbine engine↗

NASA NTRSDate not supplied

Community Radiative Transfer Model: Implementing A New Cloud Scattering Database and Developing the Forward Radar Module

The Mie theory is used by many fast RT models to estimate the optical properties of single particles. The Mie theory assumes spherical shapes for ice or snow particles with mixture of air and ice. However, hydrometeors scattering radiation at microwave frequencies have different shapes, sizes, and orientations. Therefore, using Mie theory to determine their optical properties leads to large uncertainties in all-sky radiative transfer calculations. The discrete dipole approximation (DDA) which approximates the optical properties of large objects in terms of discrete dipoles has shown promises in calculating the scattering properties of particles with different shapes in the microwave frequencies. The goal of the research was to enhance the CRTM scattering calculations for frozen hydrometeors in the microwave frequencies using the DDA technique. Given that such optical properties cannot be practically calculated on the fly, pre-computed look-up tables need to be implemented into the fast RT models to calculate the scattering properties of these particles using the DDA technique and the inputs provided by the users. Therefore, we implemented such pre-computed DDA databases into CRTM. In addition to using stand-alone CRTM calculations using collocated ATMS and reanalysis profiles, the data assimilation experiments conducted using the NOAA FV3GFS forecast system will be used to evaluate the scattering improvements. Additionally, we used the backscattering information from the DDA database to implement a radar simulator into CRTM. The radar operators takes advantage of CRTM different modules to calculate clouds absorption and scattering properties. In addition to the forward model both adjoint and tangent linear of the radar simulator are implemented and evaluated as well. The radar simulator is currently being tested within the JEDI/GEOS data assimilation framework to facilitate the assimilation of radar measurements such as CloudSat CPR and GPM DPR into the NASA GEOS model.

Isaac Moradi↗

NASA NTRSDate not supplied

Recent Developments in the Assimilation of Microwave and Radar Observations Into NWP Models

Microwave observations play a very important role in improving the weather forecasts. Although these observations are routinely assimilated into NWP models in clear-sky conditions, assimilation of all-sky microwave observations is very limited. Two main factors contributing to this limitation are inaccuracy in the input cloud and hydrometeor profiles used as input to the radiative transfer model and also error in scattering calculations performed by the radiative transfer model itself. The Mie theory is used by many fast RT models to estimate the optical properties of single particles. The Mie theory assumes spherical shapes for ice or snow particles with mixture of air and ice. However, hydrometeors scattering radiation at microwave frequencies have different shapes, sizes, and orientations. Therefore, using Mie theory to determine their optical properties leads to large uncertainties in all-sky radiative transfer calculations. The discrete dipole approximation (DDA) which approximates the optical properties of large objects in terms of discrete dipoles has shown promise in calculating the scattering properties of particles with different shapes in the microwave frequencies. This presentation focuses on recent advancements in the CRTM scattering calculations for frozen hydrometeors in the microwave frequencies using the DDA technique. In addition to using stand-alone CRTM calculations using collocated ATMS and reanalysis profiles, the data assimilation experiments conducted using the NOAA FV3GFS forecast system are used to evaluate the scattering improvements. Additionally, the backscattering information from the DDA database was used to implement a radar simulator into CRTM. The radar operator takes advantage of CRTM different modules to calculate clouds absorption and scattering properties. In addition to the forward model both adjoint and tangent linear of the radar simulator are implemented and evaluated as well. The radar simulator is currently being tested within the JEDI/GEOS data assimilation framework to facilitate the assimilation of radar measurements such as CloudSat CPR and GPM DPR into the NASA GEOS model.

Isaac Moradi↗

NASA NTRSDate not supplied

Enhancing CRTM All-Sky Simulations and Implementation of A New Active Sensor Module

Microwave observations play a very important role in improving the weather forecasts. Although these observations are routinely assimilated into NWP models in clear-sky conditions, assimilation of all-sky microwave observations is very limited. Two main factors contributing to this limitation are inaccuracy in the input cloud and hydrometeor profiles used as input to the radiative transfer model and also error in scattering calculations performed by the radiative transfer model itself. The Mie theory is used by many fast RT models to estimate the optical properties of single particles. The Mie theory assumes spherical shapes for ice or snow particles with mixture of air and ice. However, hydrometeors scattering radiation at microwave frequencies have different shapes, sizes, and orientations. Therefore, using Mie theory to determine their optical properties leads to large uncertainties in all-sky radiative transfer calculations. The discrete dipole approximation (DDA) which approximates the optical properties of large objects in terms of discrete dipoles has shown promise in calculating the scattering properties of particles with different shapes in the microwave frequencies. This presentation focuses on recent advancements in the CRTM scattering calculations for frozen hydrometeors in the microwave frequencies using the DDA technique. In addition to using stand-alone CRTM calculations using collocated ATMS and reanalysis profiles, the data assimilation experiments conducted using the NOAA FV3GFS forecast system are used to evaluate the scattering improvements. Additionally, the backscattering information from the DDA database was used to implement a radar simulator into CRTM. The radar operator takes advantage of CRTM different modules to calculate clouds absorption and scattering properties. In addition to the forward model both adjoint and tangent linear of the radar simulator are implemented and evaluated as well. The radar simulator is currently being tested within the JEDI/GEOS data assimilation framework to facilitate the assimilation of radar measurements such as CloudSat CPR and GPM DPR into the NASA GEOS model.

Isaac Moradi↗

NASA NTRSDate not supplied

CRTM Microwave Cloud Scattering Lookup Tables and Radar Simulator

Microwave observations play a very important role in improving the weather forecasts. Although these observations are routinely assimilated into NWP models in clear-sky conditions, assimilation of all-sky microwave observations is very limited. Two main factors contributing to this limitation are inaccuracy in the input cloud and hydrometeor profiles used as input to the radiative transfer model and also error in scattering calculations performed by the radiative transfer model itself. The Mie theory is used by many fast RT models to estimate the optical properties of single particles. The Mie theory assumes spherical shapes for ice or snow particles with mixture of air and ice. However, hydrometeors scattering radiation at microwave frequencies have different shapes, sizes, and orientations. Therefore, using Mie theory to determine their optical properties leads to large uncertainties in all-sky radiative transfer calculations. The discrete dipole approximation (DDA) which approximates the optical properties of large objects in terms of discrete dipoles has shown promise in calculating the scattering properties of particles with different shapes in the microwave frequencies. This presentation focuses on recent advancements in the CRTM scattering calculations for frozen hydrometeors in the microwave frequencies using the DDA technique. In addition to using stand-alone CRTM calculations using collocated ATMS and reanalysis profiles, the data assimilation experiments conducted using the NOAA FV3GFS forecast system are used to evaluate the scattering improvements. Additionally, the backscattering information from the DDA database was used to implement a radar simulator into CRTM. The radar operator takes advantage of CRTM different modules to calculate clouds absorption and scattering properties. In addition to the forward model both adjoint and tangent linear of the radar simulator are implemented and evaluated as well. The radar simulator is currently being tested within the JEDI/GEOS data assimilation framework to facilitate the assimilation of radar measurements such as CloudSat CPR and GPM DPR into the NASA GEOS model.

Isaac Moradi↗

NASA NTRSDate not supplied

Advances in Integrally Formed Metallic Structures

NASA Langley Research Center (LaRC) is applying flow forming technology to aerospace aluminum alloys for the manufacture of integrally stiffened cylinders that meet aircraft fuselage or launch vehicle specifications. High-strength 2xxx series alloys, in various temper/product form conditions, are being compared with medium-strength, very formable AA 6061 as the benchmark. Screening of candidate materials traditionally relies on empirical forming trials, but more recently on metrics derived from constant nominal strain rate tensile testing. In this work, the established hierarchy of formability metrics is adopted as the baseline; tensile area reduction, work hardening exponent, and modulus of resilience. The suite of metrics can be expanded based on phenomenological and mechanistic considerations of plastic flow instabilities to incorporate anisotropy ratio, rate of work hardening, and dynamic strain aging effects. Separate research thrusts at LaRC are aimed at formulating a protocol for scalable production of fully formed, defect-free components: 1) quantifying the extended set of formability metrics from constant and jump strain rate tensile tests with digital image correlation (DIC); 2) using statistically designed experiments on a vertical spin/flow forming facility (WF VUD-600®) to isolate the effect of convenient process variables, such as axial feed rate and thickness reduction; and 3) predicting the effect of feed ratio (roller translation relative to mandrel rotation speeds) on material response via process modeling using the DEFORM® simulation software. Current results will be discussed in terms of correlating intrinsic material properties with the bulk workability characteristics to successfully fabricate cylinders with complex cross-sections.

Aluminum↗

NASA NTRSDate not supplied

Magnetohydrodynamics (MHD) Aerocapture System for Enabling Faster-Larger Planetary Science & Human Exploration Missions

Since our completing the NIAC Phase I NIAC on this Advanced Aerocapture System, NASA Langley Research Center has funded or supported a number of studies and code enhancements through its Center Innovation Fund (CIF) and NASA’s NSTGRO and Internship Programs to mature the analysis capabilities and quantify the merits of the MHD Aerocapture System technology. These efforts have resulted in a plug and play analysis capability for assessing MHD aerocapture system performance for arrival at many planetary bodies of interest. Our efforts have especially focused on the potential mass savings for improving the capacity for science observations at Neptune and Triton. A re-cent Forbes article published “‘Orbital mechanics is probably going to decide for us whether we go to Uranus or Neptune because we need to flyby Jupiter,’ said Kunio Sayanagi at Hampton University, Virginia, who also worked on the Neptune Odyssey proposal…. Exactly when a mission can be sent to Uranus, or Neptune, depends on the relative position of Jupiter, which can help give a spacecraft a gravitational slingshot. That drastically shortens the cruise phase.” [1] Since shortening the cruise phase is important for these science missions, any mass savings enabled by the MHD Aerocapture System could be reallocated to increasing Thermal Protection System mass to allow faster arrival speeds and/or for onboarding additional payloads such as science instruments, batteries, or propellant for conducting more science for longer durations in the desired orbits. The analysis steps and codes for conducting trades and sizing vehicles for aerocapture are as follows: Step 1 is to conduct aeroheating analysis using LAURA of the selected entry vehicle shape to identify locations on the forebody where ionization and flow velocity are sufficient for producing Lo-rentz forces. LAURA is a multiblock structured grid finite-volume CFD solver developed at the NASA Langley Research Center. [2] LAURA has been used for aerothermal analysis support of the entry, de-scent and landing (EDL) phase of interplanetary missions over the last three decades [3-7]. Step 2 is to port the LAURA results into CFDWARP to calcu-late electrical and thermal conductivities of ionized flow for sizing MHD patch system and calculating Lorentz forces needed for controls analysis. CFDWARP is a CFD code that uses advanced nu-merical methods that enable the simulation of the full coupling between the aerodynamics, the magne-tohydrodynamics, and the non-neutral plasma sheaths. CFDWARP has the unique capability to simulate efficiently the non-neutral sheaths (near the electrodes) in coupled form with the quasi-neutral bulk MHD flow [8-11]. Step 3 is to link re-sults from LAURA and CFDWARP into POST2 for calculating entry trajectories and comparing MHD control results with other aerodynamic control strategies. The Program to Optimize Simulated Tra-jectories II (POST2) is a generalized point mass, discrete parameter targeting and optimization pro-gram. POST2 provides the capability to target and optimize point mass trajectories for multiple pow-ered or un-powered vehicles near an arbitrary rotat-ing, oblate planet [12]. Step 4: TPS sizing was per-formed using the Fully Implicit Ablation and Ther-mal-response code (FIAT) tool which computes the transient one-dimensional thermal response and surface thermochemistry of a multilayer stackup of thermal protection, bonding, and structural materi-als subject to aeroheating on one surface [13]. The sizing and margining methodology used was based on the approach documented by Mahzari and Milos [14] for the dual-layered heatshield for extreme entry environment technology (DL-HEEET) TPS concept. TPS analysis utilizes trajectory information from POST2. Using this step-wise plug and play MHD Aerocapture performance assessment process, our analysis targets a Neptune aerocapture trajectory that will place the spacecraft in an observation orbit for Triton. [15]. Magnetohydrodynamic (MHD) control of a 4.5-meter diameter MSL-style capsule resulted in TPS mass savings of nearly 2000 kg when using an MHD system mass of under 200 kg. The flight path for a vehicle using the MHD control strategy has a much lower heat rate and heat load compared to the conventional aerodynamic aerocapture strategies known as bank angle con-trolled (BAC) and direct force controlled (DFC). Both BAC and DFC have heat rates significantly greater than 1500 W/cm2 typically used as an upper limit for PICA. Thus, DL-HEEET TPS concept was required for the BAC and DFC control strategies. However, considering the more benign environ-ments for the MHD case, additional TPS concepts with improved mass efficiency were also assessed. PICA was considered for the MHD controlled strat-egy since the maximum heat rate was well within the limits (<1500 W/cm2) of PICA. TPS sizing re-sulted in a significant mass reduction. The PICA layer for this sizing case was about 7.8 cm. As a point of reference, the Mars 2020 mission, which used this same PICA concept, had a PICA thickness of 3.18 cm [16]. The trajectories used for the TPS sizing originat-ed from the POST2 simulations. The current, I, to an electromagnet configuration can be manipulated to allow for active control of the vehicle. Manipula-tion of the current, I, changes the magnetic field, B, which affects the Lorentz force and therefore the MHD drag force on the vehicle. Our analysis in-cluded both open-loop and close-loop control. Closed-loop control will enable improved overall performance when taking into account mission level uncertainties, such as interplanetary delivery errors and atmospheric modeling uncertainties. The open-loop and closed-loop MHD control cases do not dip as deep into the atmosphere as the aerodynamic cases. Three types of aerodynamic-only approach-es are investigated: bank angle modulation (BAM), director force control (DFC), and Drag Modulated. BAM and DFC make use of vehicle aerodynamic angles to steer the vehicle. Thus, changing the aer-odynamic forces acting on the vehicle for control, aerodynamic drag modulated case requires a vary-ing drag area to modulate the drag force. The MHD drag modulated case modulates MHD generated drag force that adds to the aerodynamic drag. This higher atmospheric activation of drag forces by the MHD patch results in significantly less heat flux on the vehicle. The MHD technology will enable shorter cruise times and deceleration of larger payloads for increasing the capacity for science at the Ice Giants or for returning astronauts to Earth from cislunar space or from Mars. The purpose of this presentation is to provide more details about this work and to highlight plans for further research and development including a flight demonstration.

R. W. Moses↗

NASA NTRS1994

Numerical simulation of large-scale field-aligned current generation from finite-amplitude magnetosonic waves

A two-dimensional numerical simulation of finite-amplitude magnetohydrodynamic (MHD) magnetosonic waves is performed under a finite-velocity background convection condition. Isothermal cases are considered for simplicity. External dissipation is introduced by assuming that the field-aligned currents are generated in proportion to the accumulated charges. The simulation results are as follows: Paired field-aligned currents are found from the simulated waves. The flow directions of these field-aligned currents depend on the angle between the background convection and the wave normal, and hence two pairs of field-aligned currents are found from a bowed wave if we look at the overall structure. The majority of these field-aligned currents are closed within each pair rather than between two wings. These features are not observed under slow background convection. The result could be applied to the cusp current system and the substorm current system.

Yamauchi, M.↗

NASA NTRS1981

Numerical simulation of sheath structure and current-voltage characteristics of a conductor-dielectric disk in a plasma

A computer program is being developed to simulate the interaction of a plasma with a conducting disk. Two configurations are examined: (1) the conductor is a 'button' in the center of a larger dielectric disk, and (2) the conducting disk is covered by a dielectric disk to the same size with a circular hole in the center of the dielectric, exposing a region of conductor. Results of the electrostatic plasma simulation are presented both with and without secondary electron emission from the dielectric; characteristic curves and voltage profiles are included.

Chaky, R. C.↗

NASA NTRS1992

Design of an air traffic computer simulation system to support investigation of civil tiltrotor aircraft operations

This research project addresses the need to provide an efficient and safe mechanism to investigate the effects and requirements of the tiltrotor aircraft's commercial operations on air transportation infrastructures, particularly air traffic control. The mechanism of choice is computer simulation. Unfortunately, the fundamental paradigms of the current air traffic control simulation models do not directly support the broad range of operational options and environments necessary to study tiltrotor operations. Modification of current air traffic simulation models to meet these requirements does not appear viable given the range and complexity of issues needing resolution. As a result, the investigation of systemic, infrastructure issues surrounding the effects of tiltrotor commercial operations requires new approaches to simulation modeling. These models should be based on perspectives and ideas closer to those associated with tiltrotor air traffic operations.

Rogers, Ralph V.↗

NASA NTRS2015

The Substorm Current Wedge: Further Insights from MHD Simulations

Using a recent magnetohydrodynamic simulation of magnetotail dynamics, we further investigate the buildup and evolution of the substorm current wedge (SCW), resulting from flow bursts generated by near-tail reconnection. Each flow burst generates an individual current wedge, which includes the reduction of cross-tail current and the diversion to region 1 (R1)-type field-aligned currents (earthward on the dawn and tailward on the duskside), connecting the tail with the ionosphere. Multiple flow bursts generate initially multiple SCW patterns, which at later times combine to a wider single SCW pattern. The standard SCWmodel is modified by the addition of several current loops, related to particular magnetic field changes: the increase of Bz in a local equatorial region (dipolarization), the decrease of |Bx| away from the equator (current disruption), and increases in |By| resulting from azimuthally deflected flows. The associated loop currents are found to be of similar magnitude, 0.1-0.3 MA. The combined effect requires the addition of region 2 (R2)-type currents closing in the near tail through dawnward currents but also connecting radially with the R1 currents. The current closure at the inner boundary, taken as a crude proxy of an idealized ionosphere, demonstrates westward currents as postulated in the original SCW picture as well as North-South currents connecting R1- and R2-type currents, which were larger than the westward currents by a factor of almost 2. However, this result should be applied with caution to the ionosphere because of our neglect of finite resistance and Hall effects.

reconnection↗

NASA NTRS2019

Spectroscopic Behavior of Composite, Black Thermal Paint, Solar Cell, and Multi-layered Insulation Materials in a GEO Simulated Environment

Materials currently populating Earth orbital regimes can be distinguished by comparing remote observational data to that of optical material measurements obtained in the laboratory. Experimentation for this research primarily involved the acquisition of spectroscopic measurements on materials of interest to the telescopic observational community for enhanced space situational awareness. Common spacecraft materials worthy of preeminent analysis for this investigation include a carbon-carbon (c-c) matrix composite, various black thermal paints, a GPS solar cell and three different cover glass components. These materials were subjected to a simulated geosynchronous Earth orbit (GEO) space environment with the intent of observing material optical property behavior over quantitative exposure time. The aforementioned materials have been measured in their pristine and GEO simulated exposed conditions. A reflectance spectrometer and a bi-directional reflectance distribution function (BRDF) optical system have been operated to perform material characterization, optical property analysis, and to further compare such data to telescopic observational data acquired on equal materials.

Reyes, Jacqueline A.↗

NASA NTRS2015

LightForce Photon-pressure Collision Avoidance: Efficiency Analysis in the Current Debris Environment and Long-Term Simulation Perspective

This work provides an efficiency analysis of the LightForce space debris collision avoidance scheme in the current debris environment and describes a simulation approach to assess its impact on the long-term evolution of the space debris environment. LightForce aims to provide just-in-time collision avoidance by utilizing photon pressure from ground-based industrial lasers. These ground stations impart minimal accelerations to increase the miss distance for a predicted conjunction between two objects. In the first part of this paper we will present research that investigates the short-term effect of a few systems consisting of 10kW class lasers directed by 1.5 m diameter telescopes using adaptive optics. The results found such a network of ground stations to mitigate more than 85 percent of conjunctions and could lower the expected number of collisions in Low Earth Orbit (LEO) by an order of magnitude. While these are impressive numbers that indicate LightForce's utility in the short-term, the remaining 15 percent of possible collisions contain (among others) conjunctions between two massive objects that would add large amount of debris if they collide. Still, conjunctions between massive objects and smaller objects can be mitigated. Hence we choose to expand the capabilities of the simulation software to investigate the overall effect of a network of LightForce stations on the long-term debris evolution. In the second part of this paper, we will present the planed simulation approach for that effort.

conjunction analysis↗

NASA NTRS1987

Boundary layer simulation improvement

The current Boundary Layer Integral Matrix Procedure - Version J (BLIMPJ) is advanced with regard to the previously modeled calculation methods accounting for surface roughness, relaminarization, condensed phase, and thick boundary layer effects. Current analytical limitations will be relaxed to permit more realistic wall and flow conditions and to use appropriate turbulence models with specific emphasis for the projected Orbit Transfer Vehicle (OTV) engine application. The updates will be incorporated into the BLIMPJ computer program, and the modified program will be made operational on the MSFC CRAY computer system. Experimental feasibility studies were conducted to find out how to obtain quality test data with advanced instrumentation for concept verification purposes.

Praharaj, Sarat C.↗

NASA NTRS1992

Identification of time-varying structural dynamic systems - An artificial intelligence approach

An application of the artificial intelligence-derived methodologies of heuristic search and object-oriented programming to the problem of identifying the form of the model and the associated parameters of a time-varying structural dynamic system is presented in this paper. Possible model variations due to changes in boundary conditions or configurations of a structure are organized into a taxonomy of models, and a variant of best-first search is used to identify the model whose simulated response best matches that of the current physical structure. Simulated model responses are verified experimentally. An output-error approach is used in a discontinuous model space, and an equation-error approach is used in the parameter space. The advantages of the AI methods used, compared with conventional programming techniques for implementing knowledge structuring and inheritance, are discussed. Convergence conditions and example problems have been discussed. In the example problem, both the time-varying model and its new parameters have been identified when changes occur.

Glass, B. J.↗

NASA NTRS1996

Retrieval of Bidirectional Reflectance Factors and Directional-Hemispherical Reflectances Using Space-Based and Airborne Multi-Angle Observations

MISR is scheduled for launch in 1998 on the EOS AM1 platform. The algorithms needed to analyze data from this instrument are currently being tested, using both simulated data and data currently available from the airborne ASAS multi-angle instrument...Results of the retrieval algorithms are presented using simulated MISR data.

MISR EOS algorithms retrieval algorithms↗