SEARCH · Engineering Papers

Results for “shear correction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17

All sources NASA NTRS DOE OSTI

NASA NTRS1975

Comparison of theory and experiment for homogeneous turbulence with shear

Solutions for uniformly-sheared turbulence, in which the interaction of the turbulence with the mean shear dominates the turbulent self-interaction, are compared with experiment. An anisotropic spectral tensor, which appears general enough to represent the initial experimental turbulence, is used for the initial condition in the calculations. The evolution of one-point turbulence components and microscales, as well as two-point velocity correlations, are considered. In most cases the agreement with experiment is good. The theory correctly predicts the presence of a negative region for two-point longitudinal-velocity correlations only for point separations in the direction normal to the flow and the mean gradient.

Deissler, R. G.↗

NASA NTRS1985

Elevated temperature creep-rupture behavior of the single crystal nickel-base superalloy NASAIR 100

The creep and rupture behavior of 001-line-oriented single crystals of the nickel-base superalloy NASAIR 100 was investigated at temperatures of 925 and 1000 C. In the stress and temperature ranges studied, the steady state creep rate, time to failure, time to the onset of secondary creep, and the time to the onset of tertiary creep all exhibited power law dependencies on the applied stress. The creep rate exponents for this alloy were between seven and eight, and the modulus-corrected activation energy for creep was approximately 350 kjoule/mole, which was comparable to the measured activation energy for Ostwald ripening of the gamma-prime precipitates. Oriented gamma-prime coarsening to form lamellae perpendicular to the applied stress was very prominent during creep. At 1000 C, the formation of a continuous gamma-gamma-prime lamellar structure was completed during the primary creep stage. Shear through the gamma-gamma-prime interface is considerd to be the rate limiting step in the deformation process. Gradual thickening of the lamellae appeared to be the cause of the onset of tertiary creep. At 925 C, the fully developed lamellar structure was not achieved until the secondary or tertiary creep stages. At this temperature, the gamma-gamma-prime lamellar structure did not appear to be as beneficial for creep resistance as at the higher temperature.

Nathal, M. V.↗

NASA NTRS2009

Enhancement of USM3D Unstructured Flow Solver for High-Speed High-Temperature Shear Flows

Large temperature and pressure fluctuations have a profound effect on turbulence development in transonic and supersonic jets. For high-speed, high-temperature jet flows, standard turbulence models lack the ability to predict the observed mixing rate of a shear layer. Several proposals to address this deficiency have been advanced in the literature to modify the turbulence transport equations in a variety of ways. In the present study, some of the most proven and simple modifications to two-equation turbulence models have been selected and implemented in NASA's USM3D tetrahedral Navier-Stokes flow solver. The modifications include the addition of compressibility correction and pressure dilatation terms in the turbulence transport equations for high-speed flows, and the addition of a simple modification to the Boussinesq's closure model coefficient for high-temperature jets. The efficacy of the extended models is demonstrated by comparison with experimental data for two supersonic axisymmetric jet test cases at design pressure ratio.

Pandya, Mohagna J.↗

DOE OSTI2021

Antiphase-Boundary-Engineered Domain Switching in a (110)-Oriented BiFeO 3 Film

A ferroelectric domain wall memory device exploits the presence (or absence) of domain walls as the basis for information storage. Although structural defects strongly influence ferroelectric domain wall nucleation and growth, this correlation is far from being fully understood. For example, a single defect can play opposing roles: it can act as a nucleation site to initiate domain switching or, conversely, serve as a pinning center inhibiting domain wall motion. This is particularly the case for antiphase boundaries (APBs), whose influence on switching remains relatively unexplored despite being ubiquitous in oxide perovskite ferroelectrics. Here, we use aberration-corrected scanning transmission microscopy and in situ transmission electron microscopy under an applied bias to extensively characterize the influence of an APB on the switching behavior in a (110)-oriented BiFeO 3 thin film. We demonstrate that deterministic nucleation occurs in the proximity of a vertically oriented APB, following which domain growth occurs laterally in a symmetric fashion. Atomic-scale structural analysis reveals that the shear operation vector for the APB is 1/2[110]; this half-unit-cell shift extends over a few nanometers, implying that the APB plane is inclined toward the imaging direction. The symmetric switching observation is attributed to local inhomogeneous lattice strain and a reduction of polarization caused by the APB. These results demonstrate that an extended structural defect can be used as an active switching element rather than a stumbling block in reprogrammable domain-wall-based devices. Ultimately, this will expand the capabilities of ferroelectric thin films for future electronic devices based on ferroelectric domain walls.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

NASA NTRS1993

Toward large eddy simulation of turbulent flow over an airfoil

The flow field over an airfoil contains several distinct flow characteristics, e.g. laminar, transitional, turbulent boundary layer flow, flow separation, unstable free shear layers, and a wake. This diversity of flow regimes taxes the presently available Reynolds averaged turbulence models. Such models are generally tuned to predict a particular flow regime, and adjustments are necessary for the prediction of a different flow regime. Similar difficulties are likely to emerge when the large eddy simulation technique is applied with the widely used Smagorinsky model. This model has not been successful in correctly representing different turbulent flow fields with a single universal constant and has an incorrect near-wall behavior. Germano et al. (1991) and Ghosal, Lund & Moin have developed a new subgrid-scale model, the dynamic model, which is very promising in alleviating many of the persistent inadequacies of the Smagorinsky model: the model coefficient is computed dynamically as the calculation progresses rather than input a priori. The model has been remarkably successful in prediction of several turbulent and transitional flows. We plan to simulate turbulent flow over a '2D' airfoil using the large eddy simulation technique. Our primary objective is to assess the performance of the newly developed dynamic subgrid-scale model for computation of complex flows about aircraft components and to compare the results with those obtained using the Reynolds average approach and experiments. The present computation represents the first application of large eddy simulation to a flow of aeronautical interest and a key demonstration of the capabilities of the large eddy simulation technique.

Choi, Haecheon↗

NASA NTRS2008

Magnetofluid Turbulence in the Solar Wind

The solar wind shows striking characteristics that suggest that it is a turbulent magnetofluid, but the picture is not altogether simple. From the earliest observations, a strong correlation between magnetic fluctuations and plasma velocity fluctuations was noted. The high corrections suggest that the fluctuations are Alfven waves. In addition, the power spectrum of the magnetic fluctuation showed evidence of an inertial range that resembled that seen in fully-developed fluid turbulence. Alfven waves, however, are exact solutions of the equations of incompressible magnetohydrodynamics. Thus, there was a puzzle: how can a magnetofluid consisting of Alfven waves be turbulent? The answer lay in the role of velocity shears in the solar wind that could drive turbulent evolution. Puzzles remain: for example, the power spectrum of the velocity fluctuations is less steep than the slope of the magnetic fluctuations, nor do we understand even now why the solar wind appears to be nearly incompressible with a -5/3 power-spectral index.

Goldstein, Melvyn L.↗

NASA NTRS2009

Sensitivity of a Cloud-Resolving Model to Bulk and Explicit Bin Microphysical Schemes: Cloud Microphysics and Storm Dynamics Interactions - Part 2

Part I of this paper compares two simulations, one using a bulk and the other a detailed bin microphysical scheme, of a long-lasting, continental mesoscale convective system with leading convection and trailing stratiform region. Diagnostic studies and sensitivity tests are carried out in Part II to explain the simulated contrasts in the spatial and temporal variations by the two microphysical schemes and to understand the interactions between cloud microphysics and storm dynamics. It is found that the fixed raindrop size distribution in the bulk scheme artificially enhances rain evaporation rate and produces a stronger near surface cool pool compared with the bin simulation. In the bulk simulation, cool pool circulation dominates the near-surface environmental wind shear in contrast to the near-balance between cool pool and wind shear in the bin simulation. This is the main reason for the contrasting quasi-steady states simulated in Part I. Sensitivity tests also show that large amounts of fast-falling hail produced in the original bulk scheme not only result in a narrow trailing stratiform region but also act to further exacerbate the strong cool pool simulated in the bulk parameterization. An empirical formula for a correction factor, r(q(sub r)) = 0.11q(sub r)(exp -1.27) + 0.98, is developed to correct the overestimation of rain evaporation in the bulk model, where r is the ratio of the rain evaporation rate between the bulk and bin simulations and q(sub r)(g per kilogram) is the rain mixing ratio. This formula offers a practical fix for the simple bulk scheme in rain evaporation parameterization.

Li, Xiaowen↗

NASA NTRS2010

Turbulence and Global Properties of the Solar Wind

The solar wind shows striking characteristics that suggest that it is a turbulent magnetofluid, but the picture is not altogether simple. From the earliest observations, a strong correlation between magnetic fluctuations and plasma velocity fluctuations was noted. The high corrections suggest that the fluctuations are Alfven waves. In addition, the power spectrum of the magnetic fluctuation showed evidence of an inertial range that resembled that seen in fully-developed fluid turbulence. Alfven waves, however, are exact solutions of the equations of incompressible magnetohydrodynamics. Thus, there was a puzzle: how can a magnetofluid consisting of Alfven waves be turbulent? The answer lay in the role of velocity shears in the solar wind that could drive turbulent evolution. Puzzles remain: for example, the power spectrum of the velocity fluctuations is less steep than the slope of the magnetic fluctuations. The plasma in the magnetic tail of Earth's magnetosphere also shows aspects of turbulence, as does the plasma in the dayside magnetosphere near the poles the dayside cusps. Recently, new analyses of high time resolution magnetic field data from Cluster have offered a glimpse of how turbulence is dissipated, thus heating the ambient plasma.

Goldstein, Melvyn L.↗

DOE OSTI2025

FLAMINGO: combining kinetic SZ effect and galaxy–galaxy lensing measurements to gauge the impact of feedback on large-scale structure

Energetic feedback processes associated with accreting supermassive black holes can expel gas from massive haloes and significantly alter various measures of clustering on $\sim$Mpc scales, potentially biasing the values of cosmological parameters inferred from analyses of large-scale structure (LSS) if not modelled accurately. Here, we use the state-of-the-art FLAMINGO suite of cosmological hydrodynamical simulations to gauge the impact of feedback on large-scale structure by comparing to Planck + ACT stacking measurements of the kinetic Sunyaev–Zel’dovich (kSZ) effect of SDSS BOSS galaxies. We make careful like-with-like comparisons to the observations, aided by high precision KiDS and DES galaxy–galaxy lensing measurements of the BOSS galaxies to inform the selection of the simulated galaxies. In qualitative agreement with several recent studies using dark matter only simulations corrected for baryonic effects, we find that the kSZ effect measurements prefer stronger feedback than predicted by simulations which have been calibrated to reproduce the gas fractions of low redshift X-ray-selected groups and clusters. We find that the increased feedback can help to reduce the so-called $S_8$ tension between the observed and CMB-predicted clustering on small scales as probed by cosmic shear (although at the expense of agreement with the X-ray group measurements). However, the increased feedback is only marginally effective at reducing the reported offsets between the predicted and observed clustering as probed by the thermal SZ (tSZ) effect power spectrum and tSZ effect – weak lensing cross-spectrum, both of which are sensitive to higher halo masses than cosmic shear.

79 ASTRONOMY AND ASTROPHYSICS↗

NASA NTRS1991

An overview of self-consistent methods for fiber-reinforced composites

The Walker et al. (1989) self-consistent method to predict both the elastic and the inelastic effective material properties of composites is examined and compared with the results of other self-consistent and elastically based solutions. The elastic part of their method is shown to be identical to other self-consistent methods for non-dilute reinforced composite materials; they are the Hill (1965), Budiansky (1965), and Nemat-Nasser et al. (1982) derivations. A simplified form of the non-dilute self-consistent method is also derived. The predicted, elastic, effective material properties for fiber reinforced material using the Walker method was found to deviate from the elasticity solution for the v sub 31, K sub 12, and mu sub 31 material properties (fiber is in the 3 direction) especially at the larger volume fractions. Also, the prediction for the transverse shear modulus, mu sub 12, exceeds one of the accepted Hashin bounds. Only the longitudinal elastic modulus E sub 33 agrees with the elasticity solution. The differences between the Walker and the elasticity solutions are primarily due to the assumption used in the derivation of the self-consistent method, i.e., the strain fields in the inclusions and the matrix are assumed to remain constant, which is not a correct assumption for a high concentration of inclusions.

Gramoll, Kurt C.↗

NASA NTRS2007

Turbulence and Global Properties of the Solar Wind

The solar wind shows striking characteristics that suggest that it is a turbulent magnetofluid, but the picture is not altogether simple. From the earliest observations, a strong correlation between magnetic fluctuations and plasma velocity fluctuations as noted. The high corrections suggest that the fluctuations are Alven waves. In addition, the power spectrum of the magnetic fluctuation showed evidence of an inertial range that resembled that seen in fully-developed fluid turbulence. Alfven waves, however, are exact solutions of the equations of an incompressible magnetohydrodynamics. Thus, there was a puzzle: how can a magnetofluid consisting of Alfven waves be turbulent? The answer lay in the role of velocity shears in the solar wind that could drive turbulent evolution. Puzzles remain: for example, the power spectrum of the velocity fluctuations is less steep than the slope of the magnetic fluctuations. The plasma in the magnetic tail of Earth's magnetosphere also shows aspects of turbulence, as does the plasma in the dayside magnetosphere near the poles--the so-called dayside cusps.

Goldstein, Melvyn L.↗

NASA NTRS2004

Associative Flow Rule Used to Include Hydrostatic Stress Effects in Analysis of Strain-Rate-Dependent Deformation of Polymer Matrix Composites

designing reliable composite engine cases that are lighter than the metal cases in current use. The types of polymer matrix composites that are likely to be used in such an application have a deformation response that is nonlinear and that varies with strain rate. The nonlinearity and the strain-rate dependence of the composite response are due primarily to the matrix constituent. Therefore, in developing material models to be used in the design of impact-resistant composite engine cases, the deformation of the polymer matrix must be correctly analyzed. However, unlike in metals, the nonlinear response of polymers depends on the hydrostatic stresses, which must be accounted for within an analytical model. By applying micromechanics techniques along with given fiber properties, one can also determine the effects of the hydrostatic stresses in the polymer on the overall composite deformation response. First efforts to account for the hydrostatic stress effects in the composite deformation applied purely empirical methods that relied on composite-level data. In later efforts, to allow polymer properties to be characterized solely on the basis of polymer data, researchers at the NASA Glenn Research Center developed equations to model the polymers that were based on a non-associative flow rule, and efforts to use these equations to simulate the deformation of representative polymer materials were reasonably successful. However, these equations were found to have difficulty in correctly analyzing the multiaxial stress states found in the polymer matrix constituent of a composite material. To correct these difficulties, and to allow for the accurate simulation of the nonlinear strain-rate-dependent deformation analysis of polymer matrix composites, in the efforts reported here Glenn researchers reformulated the polymer constitutive equations from basic principles using the concept of an associative flow rule. These revised equations were characterized and validated in an experimental program carried out through a university grant with the Ohio State University, wherein tensile and shear deformation data were obtained for a representative polymer for strain rates ranging from quasi-static to high rates of several hundred per second. Tensile deformation data also were obtained over a variety of strain rates and fiber orientation angles for a representative polymer matrix composite composed using the polymer.

Goldberg, Robert K.↗

DOE OSTI2024

Altering translation allows E. coli to overcome chemically stabilized G-quadruplexes

Genomic DNA from each sample was prepared using the Wizard Genomic DNA Purification Kit (Promega) and after, DNA was quantified using the QuantiFluor ONE dsDNA System (Promega). Genomic DNA underwent shearing to ~200 bp fragments via sonication and the gDNA fragments were prepared for sequencing using the NEBNext Ultra II DNA Library Prep Kit for Illumina (NEB). Bead-based size selection was used to select ~200 bp fragments and the fragments then underwent a splinkerette PCR using a Tn5-enriching forward primer and custom reverse primers for multiplexing. A final bead-based size selection was used to select for the correct length DNA. DNA was sequenced at the University of Michigan Advanced Genomics Core using Illumina sequencing with a custom read primer reading the last 10 nt of the transposon. PhiX174 DNA spike was added to the run to ensure sufficient sequence diversity on the flow cell. Then, a custom index read primer and standard Illumina primer were used to sequence the index reads and PhiX174, respectively.

Keck, James L.↗

DOE OSTI2025

Improved pressure-gradient sensor for the prediction of separation onset in RANS models

Here, we improve upon two key aspects of the Menter shear stress transport (SST) turbulence model: (1) We propose a more robust adverse pressure gradient sensor based on the strength of the pressure gradient in the direction of the local mean flow; (2) We propose two alternative eddy viscosity models to be used in the adverse pressure gradient regions identified by our sensor. Direct numerical simulations of the Boeing Gaussian bump are used to identify the terms in the baseline SST model that need correction, and a posteriori Reynolds-averaged Navier-Stokes calculations are used to calibrate coefficient values, leading to a model that is both physics driven and data informed. The two sensor-equipped models are applied to two thick airfoils representative of modern wind turbine applications, the FFA-W3-301 and the DU00-W-212. The proposed models improve the prediction of stall (onset of separation) with respect to the prediction of the baseline SST model.

17 WIND ENERGY↗

NASA NTRS1988

Clockwise rotation of the western Mojave Desert

A study of paleomagnetic data from Miocene volcanic rocks in the western Mojave Desert, which suggests about 25 deg of clockwise rotation, is presented. A total of 166 oriented core samples of two types of basalt were taken from 19 sites in the region. After demagnetization to 40 or 60 mT, application of structural corrections, and inversion of reversed sites, the data yielded an average direction of 51.6 deg inclination and 15.6 deg declination. When compared with the expected direction for Miocene rocks for stable North America, the direction for these Mojave rocks shows a clockwise rotation of 23.8 deg + or - 11.3 deg and a flattening of about 2.1 deg, a rotation which agrees in direction with oroclinal bending of the southern Sierra Nevada due to right-lateral shear along the western margin of North America. Most of this rotation is constrained by other paleomagnetic and strucural information to have occurred soon after the sampled basalts were deposited (about 20 Ma) and before about 16 Ma. These clockwise declination anomalies indicate that any subsequent counterclockwise rotation is small and/or compensated by previous clockwise rotation.

Golombek, Matthew P.↗

NASA NTRS2011

Deep Moonquake Focal Mechanisms: Recovery and Implications

A defining characteristic of deep moonquakes is their tendency to occur with tidal periodicity, prompting previous studies to infer that they are related to the buildup and release of tidal stress within the Moon. In studies of tidal forcing, a key constraint is the focal mechanism: the fault parameters describing the type of failure moonquakes represent. The quality of the lunar seismic data and the limited source/receiver geometries of the Apollo seismic network prohibit the determination of deep moonquake fault parameters using first-motion polarities, as is typically done in terrestrial seismology. Without being able to resolve tidal stress onto a known failure plane, we can examine only gross qualities of the tidal stress tensor with respect to moonquake occurrence, so we cannot fully address the role of tidal stress in moonquake generation. We will examine the extent to which shear (S) and compression (P) wave amplitude ratios can constrain moonquake fault geometry by determining whether, for a given cluster, there exists a focal mechanism that can produce a radiation pattern consistent with the amplitudes measured by the Apollo instruments. Amplitudes are read in the ray coordinate frame, directly from seismograms for which the P and S arrivals are clearly identifiable on all long-period channels of the four Apollo stations. We apply an empirical station correction to account for site effects and the differences between P- and S-wave attenuation. Instead of focusing on the best fitting solution only, we formulate the inverse problem using a falsification criterion: all source orientations that do not reproduce the observed SV/P ratios within an error margin derived from the uncertainty of amplitude readings are rejected. All others are accepted as possible solutions. The inversion is carried out using an exhaustive grid search on a regular grid with predefined step size, encompassing all possible combinations of strike, dip and slip. To assess the sensitivity of the inversion for the uncertainty of the lunar interior structure, we carry out repeated inversions with different velocity structures. Our data set consist of a total of 106 events from 25 deep moonquake clusters. The largest contribution of 37 events originates from the most active cluster, A001, while other clusters are represented by 1 to 9 events. Since the definition of a cluster implies that all events share the same source orientation, a comparison of the inversion results of all events from one cluster will reduce ambiguities of the inversion. Once we obtain a suite of fault parameters for a given source, we can attempt to further constrain the focal mechanism with refined analyses of tidal stresses and predictions based on synthetic seismograms.

Knapmeyer, Martin↗

NASA NTRS1983

Numerical simulation of separated flows

A new numerical method, based on the Vortex Method, for the simulation of two-dimensional separated flows, was developed and tested on a wide range of gases. The fluid is incompressible and the Reynolds number is high. A rigorous analytical basis for the representation of the Navier-Stokes equation in terms of the vorticity is used. An equation for the control of circulation around each body is included. An inviscid outer flow (computed by the Vortex Method) was coupled with a viscous boundary layer flow (computed by an Eulerian method). This version of the Vortex Method treats bodies of arbitrary shape, and accurately computes the pressure and shear stress at the solid boundary. These two quantities reflect the structure of the boundary layer. Several versions of the method are presented and applied to various problems, most of which have massive separation. Comparison of its results with other results, generally experimental, demonstrates the reliability and the general accuracy of the new method, with little dependence on empirical parameters. Many of the complex features of the flow past a circular cylinder, over a wide range of Reynolds numbers, are correctly reproduced.

Spalart, P. R.↗

DOE OSTI2023

Progress in the validation of rotor aerodynamic codes using field data

Within the framework of the fourth phase of the International Energy Agency (IEA) Wind Task 29, a large comparison exercise between measurements and aeroelastic simulations has been carried out featuring three simulation cases in axial, sheared and yawed inflow conditions. Results were obtained from more than 19 simulation tools originating from 12 institutes, ranging in fidelity from blade element momentum (BEM) to computational fluid dynamics (CFDs) and compared to state-of-the-art field measurements from the 2 MW DanAero turbine. More than 15 different variable types ranging from lifting-line variables to blade surface pressures, loads and velocities have been compared for the different conditions, resulting in over 250 comparison plots. The result is a unique insight into the current status and accuracy of rotor aerodynamic modeling. For axial flow conditions, a good agreement was found between the various code types, where a dedicated grid sensitivity study was necessary for the CFD simulations. However, compared to wind tunnel experiments on rotors featuring controlled conditions, it remains a challenge to achieve good agreement of absolute levels between simulations and measurements in the field. For sheared inflow conditions, uncertainties due to rotational and unsteady effects on airfoil data result in the CFD predictions standing out above the codes that need input of sectional airfoil data. However, it was demonstrated that using CFD-synthesized airfoil data is an effective means to bypass this shortcoming. For yawed flow conditions, it was observed that modeling of the skewed wake effect is still problematic for BEM codes where CFD and free vortex wake codes inherently model the underlying physics correctly. The next step is a comparison in turbulent inflow conditions, which is featured in IEA Wind Task 47. Doing this analysis in cooperation under the auspices of the IEA Wind Technology Collaboration Program (TCP) has led to many mutual benefits for the participants. The large size of the consortium brought ample manpower for the analysis where the learning process by combining several complementary experiences and modeling techniques gave valuable insights that could not be found when the analysis is carried out individually.

17 WIND ENERGY↗