Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “process development”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

IACMI Project 4.7: Pultruded Textile Carbon Fiber for Spar Caps (Final Report)

The primary objective of this project was to demonstrate the potential to significantly reduce the cost of wind turbine blades with carbon fiber reinforced polymer (CFRP) structure. Applicability of textile carbon fibers (TCF) were evaluated for use in pultruded spar cap (SC) elements as a path to cost reduction for utility scale wind turbine blades. In earlier work for the Department of Energy (DOE) Wind Energy Technologies Office (WETO), a collaboration of Sandia National Laboratory (SNL), Oak Ridge National Laboratory (ORNL), and Montana State University has demonstrated potential for pultruded TCF to compete with infused fiberglass and commercially available carbon fiber pultruded sections for spar cap construction. In the design cases evaluated, the TCF sections fared well when compared on cost per unit composite stiffness and cost per unit composite compressive strength for those designs [1]. Both stiffness and compressive strength tend to be key factors in the design of blade composite Spar Cap which carry the bulk of the blade structural loads in bending. Spar Cap design tends to distribute largely symmetric tensile and compressive stresses to opposite sides of the spar structure, but since carbon fiber composite compressive strength is typically 20-50% lower than tensile strength, the compressive loading reaches failure levels well before the tensile loading. Stiffness is critical in containing the large tip deflection in high wind loading situations. However, materials and process development were very limited in the earlier study and the work in this project was expanded to make the comparative information more representative of what will be required in order to make further inroads towards implementation. Similar to that study, this project team confirmed that the primary materials of interest for pultruded spar cap elements should be thermoset (TS) resins reinforced by carbon fibers, utilizing as high a percentage of TCF as practical to benchmark cost and performance against commercial carbon fibers. To make the closest comparison possible and eliminate specific test article size, resin selection, and equipment/operational nuance effects, the team planned to pultrude sections with 100% commercially available carbon fiber (Panex 35 carbon fiber from Zoltek) as well as samples utilizing high fractions of TCF. The resin system chosen was based on formulations recommended by large wind industry supplier Hexion and consisted of Hexion resin RSL-4597, curing agent CCA-138, and internal mold release additive 117, along with common kaolin filler ASP400P from BASF. As commonly deployed in spar cap configurations, the team had a mold built to pultrude a rectangular spar cap element of 100mm width and 3mm thickness. The extremely limited number of samples produced for the earlier study were produced with a “generic” epoxy utilized for a variety of applications by the pultruder contracted to produce test articles for demonstration purposes. More importantly, those samples were produced at a fiber fraction only slightly over 50%. Based on feedback from our industrial advisory team for that project and strongly recommended by this project team, the consensus is that it is highly desirable to obtain fiber fractions of 65-68% for significant penetration in wind blade spar cap. Although this requirement has yet to be exhaustively confirmed in readily available information, this was established as a project goal and informally decided we needed to exceed 60% fiber fraction to gain serious industry consideration. Previous TCF pultrusion trials have been challenged by the lack of robust TCF packages, resulting in non-uniform tension across and between tows, as well as excess labor and waste for removal of interleaved paper. The non-uniform tension and associated intermingling of tows in textile acrylic fiber tows and associated difficulties created from broken filaments in carbon fiber conversion inhibit the ordered packing necessary to enhance fiber fraction elevation. (These “cross-overs” are not considered undesirable for textile applications and there is some sense that they might be advantageous for those applications). In addition to work that is ongoing at the acrylic fiber manufacturers to improve their formats, The Institute of Advanced Composites Manufacturing Innovation (IACMI) Project 6.12 (report PA16-0349-6.12-01) [2] has developed and demonstrated a more robust packaging and creeling approach that at least partially addresses these issues, thus improving control of the TCF feed into the pultrusion unit. It was hoped that these and other improvements currently being implemented would allow us to achieve fiber fractions at least approaching these fiber fraction targets. During this project, sections utilizing 100% commercially available carbon fiber reinforcement were produced as a baseline, as well as sections reinforced with about 94% TCF and the balance being commercially available fiber for comparison. The most important finding was that similar to results reported in the earlier WETO-funded project and results from tests of TCF reported at IACMI meetings, this work demonstrated that sections pultruded with TCF in an epoxy resin frequently utilized in actual spar cap production had stiffness and compressive strengths largely comparable to similar sections pultruded with a commercially available carbon fiber also frequently utilized in the wind industry. Although the amount of that data is limited, some of the tensile strength results were actually closer than would have been expected based on fiber strength results provided by the TCF and commercial fiber producers. The actual test data are reported and discussed in detail in Section 5. The pultruded sections dominated by TCF reinforcement were approximately 8-10% lower in fiber fraction than for the sections produced using commercial fiber alone, making direct comparison difficult. The COVID-19 project has provided significant insight into the current state-of-the-art with various TCF product forms. The data obtained in this project will guide the planned improvements at the precursor level, especially in attaining uniform tensioning and payout to facilitate enhanced fiber fractions and overall processability of the TCF composites. The project team is providing guidance to stakeholders concerning the attributes, needs, and potential demand for TCF in wind blade spar caps. Results achieved in this project are consistent with findings in the related work cited [1] and support this guidance and the high potential for this product type. TCF precursor-producing partners continue to express interest in enhancing their product forms and the team looks forward to working with these improved materials as they become available.

42 ENGINEERING↗
DOE OSTI2022

A Hybrid Experimental and Theoretical Approach to Optimize Recovery of Rare Earth Elements from Acid Mine Drainage Precipitates by Oxalic Acid Precipitation

The development of processing techniques for the extraction of rare earth elements and critical minerals (REE/CM) from acid mine drainage precipitates (AMDp) has attracted increased interest in recent years. Processes under development often utilize a standard hydrometallurgical approach that includes leaching and solvent extraction followed by oxalic acid precipitation and calcination to produce a final rare earth oxide product. Impurities such as Ca, Al, Mn, Fe and Mg can be detrimental in the oxalate precipitation step and a survey of the literature showed limited data pertaining to the REE precipitation efficiency in solutions with high impurity concentrations. As such, a systematic laboratory-scale precipitation study was performed on a strip solution generated by the acid leaching and solvent extraction of an AMDp feedstock to identify the optimal processing conditions that maximize REE precipitation efficiency and product purity while minimizing the oxalic acid dosage. Given the unique chemical characteristics of AMDp, the feed solution utilized in this study contained a moderate concentration of REEs (440 mg/L) as well a significant concentration (>7000 mg/L total) of non-REE contaminants such as Ca, Al, Mn, Fe and Mg. Initially, a theoretical basis for the required oxalic acid dose, optimal pH and predicted precipitation efficiency was established by solution equilibrium calculations. Following the solution chemistry calculations, bench-scale precipitation experiments were conducted and these test results indicate that a pH of 1.5 to 2, a reaction time of more than 2 h and an oxalic acid dosage of 30 to 40 g/L optimized the REEs recovery of at ~95% to nearly 100% for individual REE species. The test results validated the optimal pH predicted by the solution chemistry calculations (1.5 to 5); however, the predicted dosage needed for complete REE recovery (10 g/L) was significantly lower than the experimentally-determined dosage of 30 to 40 g/L. The reason for this discrepancy was determined to be due to the large concentration of impurities and large number of potential metal complexes that cause inaccuracies in the solution equilibrium calculations. Based on these findings, a hybrid experimental and theoretical approach is proposed for future oxalic acid precipitation optimization studies.

oxalic acid precipitation↗
DOE OSTI2025

Shape‐Evolving Structured Liquids

Migration, division, and reconfiguration - functions essential to living systems - are driven by active processes. Developing synthetic mimics is an outstanding challenge. Lipid bilayers that bound natural systems are locally deformed by active species, e.g., microtubules, but the resulting non-equilibrium shapes relax when active species motion ceases, and the shape changes lack immediate control. A fully synthetic system is described, driven by active particles encapsulated by a reconfigurable nanoparticle-surfactant membrane that undergoes shape fluctuations reminiscent of living cells. These shape changes are preserved after particle activity stops. Surfactant concentration tunes the interfacial tension over three orders of magnitude, making on-demand shape evolution possible. Directional migration, division, and reconfiguration across multiple scales are possible, leading to a new class of biomimetic, reconfigurable, and responsive materials, paving the way for autonomous synthetic machines.

Kim, Paul Y↗
DOE OSTI2023

Nanopinhole Passivating Contact Si Solar Cells Fabricated with Metal-Assisted Chemical Etching

Monocrystalline Si (c-Si) solar cells with passivating contacts based on doped polycrystalline Si (poly-Si) on ≈2.0 nm silicon oxide (SiO x ) require >1000 °C thermal processing to create conducting pinholes in the SiO x layer. However, this high thermal budget can induce bulk defects in the Czochralski c-Si wafers used as the cell absorber layer. We demonstrate that pinholes can instead be created using metal-assisted chemical etching on planar or textured morphologies, at room temperature. This wet process creates up to 200 nm wide conducting pinholes that are directly observed with transmission electron and atomic force microscopies. High-performance hole-selective poly-Si/SiN y /SiO x and electron-selective poly-Si/SiO x passivating contacts are fabricated and implemented in laboratory-scale solar cells. This process development significantly broadens the range of passivation layer materials, their thicknesses, and surface morphologies, which enables the design of poly-Si contacts with superior passivating quality.

14 SOLAR ENERGY↗
DOE OSTI2023

Integrated Micro‐Scale Concentrating Photovoltaics: A Scalable Path Toward High‐Efficiency, Low‐Cost Solar Power

The global energy market is seeing increases in the electricity demand of a couple of percentage points annually. The photovoltaic (PV) industry is also growing rapidly every year. One of the PV technologies is concentrator photovoltaics (CPV). CPV uses high‐efficiency multijunction solar cells and optics to concentrate sunlight, thereby significantly reducing the amount of semiconductor material needed. Yet, due to the high upfont manufacturing cost of CPV, it currently does not offer a competitive price against silicon PV. With this a new branch is introduced to the industry, micro‐CPV, which can be broadly explained as the miniaturization of the solar cells and optical components. The motivation for micro‐CPV is lowering the cost by decreasing the material volume and enabling new system architectures and high‐throughput manufacturing methods, while still maintaining high electrical efficiencies, taking advantage of a lower thermal load, shorter optical paths, lower resistive losses, and lower material volumes. Herein, a comprehensive review of the technological advances is presented, key synergies between micro‐CPV and other industries sharing similar challenges are identified, exemplified by micro‐light emitting diodes display manufacturing. New assembly process development in these industries will facilitate commercial adoption of micro‐CPV with continued miniaturization while driving down the cost.

Jost, Norman↗
DOE OSTI2022

A New Residual Strain Mapping Program Using Energy Dispersive X-Ray Diffraction at the Advanced Photon Source

Here, the ability to non-destructively map the residual strain field inside an engineering component is important for predicting its fatigue life or developing processing methods to prevent failure or enhance performance. In this paper, we describe a new residual strain mapping program at the Advanced Photon Source, Argonne National Laboratory. The new program is based on energy dispersive x-ray diffraction (EDXRD). It is capable of non-destructively penetrating a several- cm thick polycrystalline sample fabricated from engineering alloys using high-energy x-rays and measuring the residual strain field with mm or better spatial resolution and approximately ±1 x 10 -4 strain resolution. A multi-element detector array is employed to measure multiple strain components simultaneously. The residual strain mapping setup is augmented with a high-energy tomography capability, allowing precise alignment of the material volume of interest for residual strain mapping and providing a complementary view of the structure to understand the measured strain field. These measurement capabilities are demonstrated using several strain mapping examples ranging from polycrystalline structural alloys to biological materials. We also provide some guidance for the future users of the program for a successful residual strain mapping experiment. We are expanding the capabilities of the new setup with various in situ capabilities including thermo-mechanical loading.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2023

Entanglement between valence and sea quarks in hadrons of 1+1 dimensional QCD

The conceptual interpretation of valence- and sea-quark separation, which is a key aspect of the parton model and of an intuitive picture of hadron structure, becomes obscured by quantum effects in QCD. This suggests that there may be measures of entanglement between quark degrees of freedom that are present in QCD, but absent in the intuitive picture with a clear valence-sea (VS) separation. In this paper, we define the first rigorous measure of VS entanglement in QCD in an attempt to bring conceptual clarity to this issue, and, potentially, to find a measure of the applicability of the parton model to QCD bound states. This VS entanglement vanishes in the large-N c limit, and it remains low when finite-N c states resemble their large-N c counterparts. We perform a numerical study of VS entanglement in 1 + 1 dimensional discrete light-cone quantized QCD, and in the process develop a method for building the color-singlet basis of 1 + 1d QCD that is manifestly complete and orthogonal by construction. We calculate this VS entanglement entropy for the first time and find that it is relatively low for the first few excited states of both mesons and baryons compared to all other states in the spectrum, with the VS entropy of ground state hadrons providing a minimum. We also see that for ground state mesons the entropy is well described in the 1/N c approximation. These results suggest that low energy hadrons may be the only QCD bound states for which the large-N c expansion, and perhaps the parton model, provide an accurate description. This work also provides the first evidence that the VS entanglement entropy of QCD in 3 + 1d, which would likely serve as an order parameter for the transition between quark and hadron degrees of freedom, may be perturbatively accessible through a large-N c expansion.

1+1 dimensional QCD↗
DOE OSTI2021

An assessment of the harvesting and fuel performance of a single-pass cut-and-chip harvester in commercial-scale short-rotation poplar crops as influenced by crop and weather conditions

There is a need for data on commercial-scale harvesting operations in hybrid poplar short rotation crops to better understand costs and logistics, especially for modeling large scale biorefineries. An investigation was conducted on the in-field performance of a single-pass cut-and-chip harvester operating in commercial fields for over 370 individual wagon loads representing a range of crop and field conditions. Mean material capacity peaked at 70 Mg h -1 in dry conditions in lower biomass (<60 Mg ha -1 ), but was only 28 Mg h -1 during wet conditions and often higher standing biomass. Wet ground conditions require the harvester to divert additional power to maintaining forward movement, which results in decreased material capacity and increased fuel consumption. Crops with higher standing biomass had taller trees that do not always feed as smoothly into the harvester, slowing forward progress and lowering material capacity. Mean crop specific fuel consumption, L of fuel per Mg of biomass processed, generally decreased as standing biomass increased. When standing biomass was above 40 Mg ha -1 mean crop specific fuel consumption (FCC) was 1.69 L Mg -1 in dry conditions and 3.98 L Mg -1 in wet conditions, but when standing biomass was below 40 Mg ha-1 FCC increased drastically (as high as 5 L Mg -1 ) because the harvester is putting more effort into forward speed instead of material processing. Developing relationships between material capacity and fuel consumption based on standing biomass and ground conditions at representative scales are essential for conducting environmental and economic analyses of these systems.

09 BIOMASS FUELS↗
DOE OSTI2020

Dynamic metrics of natural ventilation cooling effectiveness for interactive modeling

The evaluation of natural ventilation potential for cooling indoor spaces during the early design phases is of great interest to researchers and practitioners. Among various definitions and usages for natural ventilation potential (NVP) in early design evaluation, this paper reviews and identifies the key performance indicators, and proposes two new dynamic metrics—natural ventilation cooling effectiveness (NVCE) and climate potential utilization ratio (CPUR). The metrics are dynamically responsive to various design options, in both steady and transient states, allowing consideration of thermal mass. Assisting in design development processes, the metrics quantify how well indoor spaces make use of natural ventilation’s cooling capacity. Case studies are presented to demonstrate how NVCE and CPUR enable designers to evaluate the predicted performance and how to apply the information to improve building design. Finally, the results of the design iterations showed that the relationship among various design parameters should be dynamically understood in order to evaluate the performance of natural ventilation, confirming that “the more the airflow, the greater the potential,” and “the heavier the thermal mass, the greater the energy saving” were not always true.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2026

The U.S. Fusion Materials Community Roadmap: Near-term research priorities for the development of plasma-facing and structural materials for fusion power plants

In response to the needs of a rapidly growing private fusion industry, the U.S. Fusion Materials Coordinating Committee (FMCC) and the broader U.S. fusion materials research community undertook an extensive effort to create a comprehensive roadmap for fusion materials development. The result of this effort was the U.S. Fusion Materials Community Roadmap (US-FMCR), which describes the steps needed to advance the technical maturity of leading candidates for plasma-facing materials and structural materials for fusion power plants from laboratory-scale experiments to a point of sufficient technological readiness for industrial adoption and implementation. However, researchers face significant resource constraints as well as very aggressive pilot plant development timelines. Thus, the research strategies detailed in the US-FMCR require further assessment to downselect the specific tasks that must be prioritized within the next two to three years, in order to make the most efficient use of funding, human resources, and experimental facilities. This paper presents an overview of the US-FMCR and its development process. We also present the subset of research objectives that the FMCC identified as the most urgent research priorities for the U.S. fusion materials research community. The state-of-the-art of materials research is also highlighted for each class of materials considered in the US-FMCR. The recommendations presented here integrate an extensive evaluation of the current status of fusion materials research with a broad cross-section of opinion from the wider U.S. fusion community.

Ferry, Sara [Massachusetts Institute of Technology↗
DOE OSTI2021

Machine-learning based prediction of injection rate and solenoid voltage characteristics in GDI injectors

We report that current state-of-the-art gasoline direct-injection (GDI) engines use multiple injections as one of the key technologies to improve exhaust emissions and fuel efficiency. For this technology to be successful, secured adequate control of fuel quantity for each injection is mandatory. However, nonlinearity and variations in the injection quantity can deteriorate the accuracy of fuel control, especially with small fuel injections. Therefore, it is necessary to understand the complex injection behavior and to develop a predictive model to be utilized in the development process. This study presents a methodology for rate of injection (ROI) and solenoid voltage modeling using artificial neural networks (ANNs) constructed from a set of Zeuch-style hydraulic experimental measurements conducted over a wide range of conditions. A quantitative comparison between the ANN model and the experimental data shows that the model is capable of predicting not only general features of the ROI trend, but also transient and non-linear behaviors at particular conditions. In addition, the end of injection (EOI) could be detected precisely with a virtually generated solenoid voltage signal and the signal processing method, which applies to an actual engine control unit. A correlation between the detected EOI timings calculated from the modeled signal and the measurement results showed a high coefficient of determination.

42 ENGINEERING↗
DOE OSTI2022

Screening and evaluation of biomass upgrading strategies for sustainable transportation fuel production with biomass-derived volatile fatty acids

Biomass conversion to fuels and chemicals is crucial to decarbonization, but choosing an advantageous upgrading pathway out of many options is challenging. Rigorously evaluating all candidate pathways (process simulation, product property testing) requires a prohibitive amount of research effort; even simple upgrading schemes have hundreds of possible permutations. We present a method enabling high-throughput screening by approximating upgrading unit operations and drop-in compatibility of products (e.g., fuel properties) and apply it to volatile fatty acid (VFA) conversion to liquid transportation fuels via a MATLAB script, VFA Upgrading to Liquid Transportation fUels Refinery Estimation (VULTURE). VULTURE selects upgrading configurations that maximize fuel blend bio-derived content. We validate VULTURE's approximations through surrogate fuel property testing and process simulation. Techno-economic and life cycle analyses suggest that VFA upgrading processes down-selected by VULTURE are profitable and have low carbon intensities, demonstrating the potential for the strategy to accelerate process development timelines at decreased costs.

09 BIOMASS FUELS↗
DOE OSTI2022

Melt pool temperature measurement and monitoring during laser powder bed fusion based additive manufacturing via single-camera two-wavelength imaging pyrometry (STWIP)

Melt pool (MP) temperature is one of the determining factors and a key signature for evaluating the properties of printed components in metal additive manufacturing (AM). The state-of-the-art measurement systems are hindered, primarily by the large-scale data acquisition and processing demands. In this work, we introduce a novel coaxial, high-speed, single-camera two-wavelength imaging pyrometer (STWIP) system as opposed to the typical utilization of multiple cameras for measuring MP temperature profiles in laser powder bed fusion (LPBF) processes. Developed on a commercial LPBF machine (EOS M290), the STWIP system demonstrated its ability to quantitatively monitor the MP temperature and its variation for 50 layers at high framerates (>30,000 fps) for a real-world application (standard fatigue specimens) print. High performance computing is employed to analyze the acquired big data (MP images), for determining each MP's average temperature and 2D temperature profile. The MP temperature evolution in the gage section of a fatigue specimen is also examined at a temporal resolution of 1 ms, by evaluating the MP temperatures in the samples' first, middle, and last layers. This report is the first of its kind on monitoring MP temperature distribution and evolution at such a large, detailed scale for longer durations in practical applications.

42 ENGINEERING↗
DOE OSTI2025

AstroPix: A pixelated HVCMOS sensor for space-based gamma-ray measurement

A next-generation medium-energy gamma-ray telescope targeting the MeV range would address open questions in astrophysics regarding how extreme conditions accelerate cosmic-ray particles, produce relativistic jet outflows, and more. One concept, AMEGO-X, relies upon the mission-enabling CMOS Monolithic Active Pixel Sensor silicon chip AstroPix. AstroPix is designed for space-based use, featuring low noise, low power consumption, and high scalability. Desired performance of the device include an energy resolution of 5 keV (or 10% FWHM) at 122 keV and a dynamic range per-pixel of 25–700 keV, enabled by the addition of a high-voltage bias to each pixel which supports a depletion depth of 500 μ m. This work reports on the status of the AstroPix development process with emphasis on the current version under test, version three (v3), and highlights of version two (v2). Version 3 achieves energy resolution of 10.4 ± 3.2% at 59.5 keV and 94 ± 6 μ m depletion in a low-resistivity test silicon substrate.

Astrophysics instrumentation↗
DOE OSTI2025

Porous carbon from lignocellulosic biomass with emphasis on corn plant waste residue for energy storage

The rising global demand for sustainable energy storage materials has driven the search for environmentally friendly and cost-effective electrode options. Hydrothermal conversion of lignocellulosic biomass has gained attention due to its low energy requirements and operation at relatively low temperatures, presenting a green alternative to traditional thermochemical methods. The resulting solid product, hydrochar, has been used as an adsorbent and soil amendment; however, chemical/thermal treatment significantly enhances its physical properties. These structural modifications transform hydrochar into an effective porous carbon electrode, offering abundant sites for electrolyte ion transport, critical for high-performance devices like supercapacitors and batteries. This review first discusses various waste biomass and sustainable feedstocks available globally. It compares two primary thermochemical conversion techniques, pyrolysis and hydrothermal carbonization/liquefaction, and examines their respective solid products, biochar and hydrochar, analyzing differences in their physical and chemical characteristics. The focus is placed on hydrochar, summarizing activation methods to produce porous carbon suitable for energy storage applications. Additionally, this review will include a dedicated section on the application of porous carbon derived from corn plant waste residue, considering that corn is one of the most abundant crops grown worldwide, which makes it an important and promising source for sustainable porous carbon production. The role of machine learning models in optimizing hydrothermal processes to produce high-quality hydrochar is also discussed, emphasizing how data-driven approaches can streamline process development. Finally, the review identifies the current challenges and prospects for lignocellulosic biomass-derived porous carbon as a sustainable electrode material in next-generation energy storage technologies.

25 ENERGY STORAGE↗
DOE OSTI2024

Recycling of silver from silicon solar cells by laser debonding

A laser-debonding approach to silver electrode recovery from solar cells is presented to address the critical need for efficient and eco-friendly recycling methods. The study explores the use of UV nanosecond and IR continuous-wave lasers to precisely debond silver electrodes from silicon wafers. By optimizing parameters like laser power, scan speed, and the number of passes, intact silver electrical contact lines were recovered from solar cells. Scanning electron microscopy with energy-dispersive X-ray spectroscopy (SEM-EDS) analysis confirmed the successful separation of silver from silicon wafers. Furthermore, an increase in the number of laser passes led to the production of silver microparticles, as validated by morphology and compositional studies using EDS. The estimated silver is approximately 90 mg for the Si solar cells of 15.4 * 15.4 cm 2 used in the study. To achieve a large area recovery of silver, a MATLAB code incorporating detection algorithms and specific criteria to automate laser scanning by accurately identifying the location of silver electrodes was developed. This presented laser debonding method is not confined to silicon solar cells but can be extended to other solar cell types featuring metal electrodes, offering a versatile solution. By minimizing the use of hazardous chemicals and reducing operational costs, the developed process aligns with the imperative of environmentally responsible photovoltaic waste management.

14 SOLAR ENERGY↗
DOE OSTI2025

Stress accommodation in nanoscale dolan bridges designed for superconducting qubits

Josephson junctions are the principal circuit element in numerous superconducting quantum information devices and can be readily integrated into large-scale electronics. However, device integration at the wafer scale necessarily depends on having a reliable, high-fidelity, and high-yield fabrication method for creating Josephson junctions. When creating Al/AlO x based superconducting qubits, the standard Josephson junction fabrication method relies on a sub-micron suspended resist bridge, known as a Dolan bridge, which tends to be particularly fragile and can often times fracture during the resist development process, ultimately resulting in device failure. In this work, we demonstrate a unique Josephson junction lithography mask design that incorporates stress-relief channels. Our simulation results show that the addition of stress-relief channels reduces the lateral stress in the Dolan bridge by more than 70% for all the bridge geometries investigated. In practice, our novel mask design significantly increased the survivability of the bridge during device processing, resulting in 100% yield for over 100 Josephson junctions fabricated.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2026

Integrating three plan evaluation approaches for coordinated heat resilience in cities across the Arizona urban corridor

Increasing heat poses a growing threat to cities worldwide due to both climate change and the urban heat island effect. While heat planning and governance are still emergent, research suggests that silos and conflicts within cities' networks of plans often impede heat resilience. Integrated heat resilience planning, therefore, requires a systematic and comprehensive analysis of the silos and conflicts relevant to heat resilience within networks of plans. This study is the first to combine three complementary plan evaluation methods to assess how cities' networks of plans address heat resilience. We applied 1) plan cross-referencing, 2) Plan Quality Evaluation for Heat Resilience, and 3) Plan Integration for Resilience Scorecard™ (PIRS™) for Heat to 19 plans from seven Arizona cities. We find similarities and differences in how these cities' networks of plans address heat hazards. The plans have consistently high-quality participation and coordination principles but lack details on vulnerability and climate change uncertainty, suggesting a need to move beyond immediate heat risks. We also identify opportunities to diversify policy mechanisms, spatially target high heat risk areas, and enhance the connection between planning efforts. These results validate that plan elements are interlinked and the importance of integrative plan development processes to improve heat resilience.

Extreme heat↗