Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “predictive state estimation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Updated Available Drawdowns for Big Hill SPR Caverns - Model Including the Caprock Fault

This report updates the estimated values of the baseline available drawdowns for the caverns at the Big Hill storage facility, and an updated table listing the available drawdowns. An updated finite element numerical analysis model, which included a fault in the caprock layers, was constructed and the daily data of actual wellhead pressures and oil-brine interfaces was used. The number of available drawdowns for each of the Big Hill SPR caverns is estimated using the new model. All caverns are predicted to have five available drawdowns remaining from a geomechanical perspective. BH-101 and 105 have a region of concern at the floor edge and/or sloping floor, where tensile and dilatant stresses are predicted to occur during each workover. The tensile state is predicted to occur because of the geometries of the edge and floor. Therefore, geomechanical examination for two caverns would be recommended after a drawdown leach. The well integrity of each cavern is not investigated in this report. The estimates for the number of baseline available drawdowns are subject to change in the future as the knowledge of physical phenomena at the sites, and the further development of the models of geomechanical behavior at the sites, evolve over time.

02 PETROLEUM↗
NASA NTRS2017

Filter Tuning Using the Chi-Squared Statistic

The Goddard Space Flight Center (GSFC) Flight Dynamics Facility (FDF) performs orbit determination (OD) for the Aqua and Aura satellites. Both satellites are located in low Earth orbit (LEO), and are part of what is considered the A-Train satellite constellation. Both spacecraft are currently in the science phase of their respective missions. The FDF has recently been tasked with delivering definitive covariance for each satellite.The main source of orbit determination used for these missions is the Orbit Determination Toolkit developed by Analytical Graphics Inc. (AGI). This software uses an Extended Kalman Filter (EKF) to estimate the states of both spacecraft. The filter incorporates force modelling, ground station and space network measurements to determine spacecraft states. It also generates a covariance at each measurement. This covariance can be useful for evaluating the overall performance of the tracking data measurements and the filter itself. An accurate covariance is also useful for covariance propagation which is utilized in collision avoidance operations. It is also valuable when attempting to determine if the current orbital solution will meet mission requirements in the future.This paper examines the use of the Chi-square statistic as a means of evaluating filter performance. The Chi-square statistic is calculated to determine the realism of a covariance based on the prediction accuracy and the covariance values at a given point in time. Once calculated, it is the distribution of this statistic that provides insight on the accuracy of the covariance.For the EKF to correctly calculate the covariance, error models associated with tracking data measurements must be accurately tuned. Over estimating or under estimating these error values can have detrimental effects on the overall filter performance. The filter incorporates ground station measurements, which can be tuned based on the accuracy of the individual ground stations. It also includes measurements from the NASA space network (SN), which can be affected by the assumed accuracy of the TDRS satellite state at the time of the measurement.The force modelling in the EKF is also an important factor that affects the propagation accuracy and covariance sizing. The dominant force in the LEO orbit regime is the drag force caused by atmospheric drag. Accurate accounting of the drag force is especially important for the accuracy of the propagated state. The implementation of a box and wing model to improve drag estimation accuracy, and its overall effect on the covariance state is explored.The process of tuning the EKF for Aqua and Aura support is described, including examination of the measurement errors of available observation types (Doppler and range), and methods of dealing with potentially volatile atmospheric drag modeling. Predictive accuracy and the distribution of the Chi-square statistic, calculated based of the ODTK EKF solutions, are assessed versus accepted norms for the orbit regime.

Covariance Analysis↗
NASA NTRS1979

Optimal estimator model for human spatial orientation

A model is being developed to predict pilot dynamic spatial orientation in response to multisensory stimuli. Motion stimuli are first processed by dynamic models of the visual, vestibular, tactile, and proprioceptive sensors. Central nervous system function is then modeled as a steady-state Kalman filter which blends information from the various sensors to form an estimate of spatial orientation. Where necessary, this linear central estimator has been augmented with nonlinear elements to reflect more accurately some highly nonlinear human response characteristics. Computer implementation of the model has shown agreement with several important qualitative characteristics of human spatial orientation, and it is felt that with further modification and additional experimental data the model can be improved and extended. Possible means are described for extending the model to better represent the active pilot with varying skill and work load levels.

Borah, J.↗
DOE OSTI2021

Model Predictive Fault-Tolerant Tracking Control for PDF Control Systems With Packet Losses

In this article, a fault-tolerant tracking control strategy is investigated for nonlinear probability density function (PDF) control systems with the actuator fault, uncertainties, unknown disturbance, and random packet losses. The control input signal dropout and measurement signal dropouts are described as the independent Bernoulli distribution. An adaptive fault diagnosis (FD) observer based on the Lyapunov function is given to simultaneously estimate the fault, disturbance, and state with packet losses. Furthermore, different from the traditional robust fault-tolerant control (FTC), a new active fault-tolerant tracking controller is designed based on the model predictive control framework, which has better adaptive fault-tolerant performance. Finally, the validity of the proposed FTC method has been proved by a simulation study of a papermaking process.

42 ENGINEERING↗
DOE OSTI2023

Bayesian filtering for model predictive control of stochastic gene expression in single cells

This study describes a method for controlling the production of protein in individual cells using stochastic models of gene expression. By combining modern microscopy platforms with optogenetic gene expression, experimentalists are able to accurately apply light to individual cells, which can induce protein production. Here we use a finite state projection based stochastic model of gene expression, along with Bayesian state estimation to control protein copy numbers within individual cells. We compare this method to previous methods that use population based approaches. We also demonstrate the ability of this control strategy to ameliorate discrepancies between the predictions of a deterministic model and stochastic switching system.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2023

Quantum circuit fidelity estimation using machine learning

The computational power of real-world quantum computers is limited by errors. When using quantum computers to perform algorithms which cannot be efficiently simulated classically, it is important to quantify the accuracy with which the computation has been performed. In this work, we introduce a machine learning-based technique to estimate the fidelity between the state produced by a noisy quantum circuit and the target state corresponding to ideal noise-free computation. Our machine learning model is trained in a supervised manner, using smaller or simpler circuits for which the fidelity can be estimated using other techniques like direct fidelity estimation and quantum state tomography. Here we demonstrate that, for simulated random quantum circuits with a realistic noise model, the trained model can predict the fidelities of more complicated circuits for which such methods are infeasible. In particular, we show that the trained model may make predictions for circuits with higher degrees of entanglement than were available in the training set and that the model may make predictions for non-Clifford circuits even when the training set included only Clifford-reducible circuits. This empirical demonstration suggests classical machine learning may be useful for making predictions about beyond-classical quantum circuits for some non-trivial problems.

97 MATHEMATICS AND COMPUTING↗
NASA NTRS1973

Results of solar electric thrust vector control system design, development and tests

Efforts to develop and test a thrust vector control system TVCS for a solar-energy-powered ion engine array are described. The results of solar electric propulsion system technology (SEPST) III real-time tests of present versions of TVCS hardware in combination with computer-simulated attitude dynamics of a solar electric multi-mission spacecraft (SEMMS) Phase A-type spacecraft configuration are summarized. Work on an improved solar electric TVCS, based on the use of a state estimator, is described. SEPST III tests of TVCS hardware have generally proved successful and dynamic response of the system is close to predictions. It appears that, if TVCS electronic hardware can be effectively replaced by control computer software, a significant advantage in control capability and flexibility can be gained in future developmental testing, with practical implications for flight systems as well. Finally, it is concluded from computer simulations that TVCS stabilization using rate estimation promises a substantial performance improvement over the present design.

Fleischer, G. E.↗
NASA NTRS1988

Modelling the growth of triglycine sulphate crystals in Spacelab 3

Two triglycine sulphate crystals were grown from an aqueous solution in Spacelab 3 aboard a Space Shuttle. Using a diffusion coefficient of 0.00002 sq cm/s, a computerized simulation gave reasonable agreement between experimental and theoretical crystal sizes and interferometric lines in the solution near the growing crystal. This diffusion coefficient is larger than most measured values, possibly due to fluctuating accelerations on the order of .001 g (Earth's gravity). The average acceleration was estimated to be less than .000001 g. At this level, buoyancy driven convection is predicted to add approx. 20 percent to the steady state growth rate. Only very slight distortion of the interferometric lines was observed at the end of a 33 hr run. It is suggested that the time to reach steady state convective transport may be inversely proportional to g at low g, so that the full effect of convection was not realized in these experiments.

Yoo, Hak-Do↗
NASA NTRS2013

IRVE-3 Post-Flight Reconstruction

The Inflatable Re-entry Vehicle Experiment 3 (IRVE-3) was conducted from the NASA Wallops Flight Facility on July 23, 2012. Launched on a Black Brant XI sounding rocket, the IRVE-3 research vehicle achieved an apogee of 469 km, deployed and inflated a Hypersonic Inflatable Aerodynamic Decelerator (HIAD), re-entered the Earth's atmosphere at Mach 10 and achieved a peak deceleration of 20 g's before descending to splashdown roughly 20 minutes after launch. This paper presents the filtering methodology and results associated with the development of the Best Estimated Trajectory of the IRVE-3 flight test. The reconstructed trajectory is compared against project requirements and pre-flight predictions of entry state, aerodynamics, HIAD flexibility, and attitude control system performance.

Olds, Aaron D.↗
DOE OSTI2025

Design and Development of Novel Equiatomic Refractory Multi Principal elemental Alloys Based on MoNbTi System for Use in Irradiation Environments

Multi Principal Elemental Alloys (MPEA) have emerged as promising materials for next-generation nuclear reactors due to their exceptional irradiation resistance. Eight equiatomic MPEA based on the MoNbTi system, comprising of elements with low thermal neutron absorption cross-sections were explored using a combined approach employing empirical parameter estimations, and CALPHAD simulations by which the phases and elemental segregation observed in all the alloys in the as-cast state were predicted. Solution heat treatment at 1500°C transformed five alloys into single-phase matrix materials, enhancing homogeneity and reducing hardness. The densities of the alloys ranged between 6.47 to 7.68 g/cm3, hardness between 472 and 656 VHN, Young’s modulus between 142 GPa to 169 GPa, shear modulus between 54 GPa and 62 GPa, bulk modulus between 117 GPa to 194 GPa and Poisson’s ratio between 0.3 to 0.35. The in-situ high temperature Xray diffraction results, differential scanning calorimetry and dilatometry results up to 1000°C suggested the high temperature phase stability of the MPEA. Subsequent ageing heat treatment at 800 and 1000 oC for 96 hours revealed significant secondary phase precipitation in MoNbTiZr, MoNbTiZrV, and MoNbTiCrA. Oxidation studies at 800 oC for 24 hours in air revealed superior oxidation resistance and cubic rate law dependence in Cr containing MPEA especially in MoNbTiCrAl, while severe mass gain resulting in total disintegration and exfoliation in MoNbTiZr and MoNbTiZrV. This comprehensive study underscores the potential of novel MPEA as promising materials for advanced nuclear reactor applications, shedding light on their microstructural control, mechanical properties, thermal stability, and oxidation resistance.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS2021

Reconciling Assumptions in Bottom-up and Top-down Approaches for Estimating Aerosol Emission Rates from Wildland Fires using Observations from FIREX-AQ

Accurate fire emissions inventories are crucial to predict the impacts of wildland fires on air quality and atmospheric composition. Two traditional approaches are widely used to calculate fire emissions: a satellite-based top-down approach and a fuels-based bottom-up approach. However, these methods often considerably disagree on the amount of particulate mass emitted from fires. Previously available observational datasets tended to be sparse, and lacked the statistics needed to resolve these methodological discrepancies. Here, we leverage the extensive and comprehensive airborne in situ and remote sensing measurements of smoke plumes from the recent Fire Influence on Regional to Global Environments and Air Quality (FIREX-AQ) campaign to statistically assess the skill of the two traditional approaches. We use detailed campaign observations to calculate and compare emission rates at an exceptionally high-resolution using three separate approaches: top-down, bottom-up, and a novel approach based entirely on integrated airborne in situ measurements. We then compute the daily average of these high-resolution estimates and compare with estimates from lower resolution, global top-down and bottom-up inventories. We uncover strong, linear relationships between all of the high-resolution emission rate estimates in aggregate, however no single approach is capable of capturing the emission characteristics of every fire. Global inventory emission rate estimates exhibited weaker correlations with the high-resolution approaches and displayed evidence of systematic bias. The disparity between the low resolution global inventories and the high-resolution approaches is likely caused by high levels of uncertainty in essential variables used in bottom-up inventories and imperfect assumptions in top-down inventories. Plain Language Summary Smoke emitted by wildland fires is dangerous to human health and contributes to climate change.To predict and evaluate the impacts of fires, we need to know how much smoke is emitted into the atmosphere. There are two state-of-the-art methods used to estimate the mass of smoke emitted by fires, but they often disagree. In this study, we use unusually detailed measurements collected using an aircraft that flew within wildland fire smoke plumes to calculate the amount ofsmoke emitted from fires in the Western United States. We compare emission rates derived from the exceptionally high spatial and temporal resolution approach to the two traditional, lower resolution approaches to understand why they sometimes diverge

E B Wiggins↗
DOE OSTI2022

Fast-forwarding quantum simulation with real-time quantum Krylov subspace algorithms

Quantum subspace diagonalization (QSD) algorithms have emerged as a competitive family of algorithms that avoid many of the optimization pitfalls associated with parameterized quantum circuit algorithms. While the vast majority of the QSD algorithms have focused on solving the eigenpair problem for ground, excited-state, and thermal observable estimation, there has been a lot less work in considering QSD algorithms for the problem of quantum dynamical simulation. In this work, we propose several quantum Krylov fast-forwarding (QKFF) algorithms capable of predicting long-time dynamics well beyond the coherence time of current quantum hardware. Our algorithms use real-time evolved Krylov basis states prepared on the quantum computer and a multi-reference subspace method to ensure convergence towards high-fidelity, long-time dynamics. In particular, we show that the proposed multi-reference methodology provides a systematic way of trading off circuit depth with classical post-processing complexity. Further, we also demonstrate the efficacy of our approach through numerical implementations for several quantum chemistry problems including the calculation of the auto-correlation and dipole moment correlation functions.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2023

HVAC control fine-grained occupancy pattern estimation

A thermal state of a plurality of zones of the building is updated according to a building thermal model and information received from temperature sensors of the building. Predicted occupant counts for an upcoming plurality of time slots for each of the plurality of zones are updated using actual occupancy counts for each of the plurality of zones. A misprediction type distribution for the upcoming plurality of time slots for each of the plurality of zones is updated, the misprediction type distribution indicating misprediction for true negatives, false positives, false negatives, and true positives. A total misprediction cost expectation is updated according to the predicted occupant counts and the misprediction type distribution. HVAC power for each of the plurality of zones is determined to optimize occupant thermal comfort weighted according to the predicted occupant counts while minimizing the total misprediction cost expectation. HVAC operation is controlled per the HVAC power.

Lin, Shan↗
DOE OSTI2020

Predicting secondary organic aerosol phase state and viscosity and its effect on multiphase chemistry in a regional-scale air quality model

Atmospheric aerosols are a significant public health hazard and have substantial impacts on the climate. Secondary organic aerosols (SOAs) have been shown to phase separate into a highly viscous organic outer layer surrounding an aqueous core. This phase separation can decrease the partitioning of semi-volatile and low-volatile species to the organic phase and alter the extent of acid-catalyzed reactions in the aqueous core. A new algorithm that can determine SOA phase separation based on their glass transition temperature (T g ), oxygen to carbon (O:C) ratio and organic mass to sulfate ratio, and meteorological conditions was implemented into the Community Multiscale Air Quality Modeling (CMAQ) system version 5.2.1 and was used to simulate the conditions in the continental United States for the summer of 2013. SOA formed at the ground/surface level was predicted to be phase separated with core–shell morphology, i.e., aqueous inorganic core surrounded by organic coating 65.4 % of the time during the 2013 Southern Oxidant and Aerosol Study (SOAS) on average in the isoprene-rich southeastern United States. Our estimate is in proximity to the previously reported ~70 % in literature. The phase states of organic coatings switched between semi-solid and liquid states, depending on the environmental conditions. The semi-solid shell occurring with lower aerosol liquid water content (western United States and at higher altitudes) has a viscosity that was predicted to be 10 2 –10 12 Pa s, which resulted in organic mass being decreased due to diffusion limitation. Organic aerosol was primarily liquid where aerosol liquid water was dominant (eastern United States and at the surface), with a viscosity <10 2 Pa s. Phase separation while in a liquid phase state, i.e., liquid–liquid phase separation (LLPS), also reduces reactive uptake rates relative to homogeneous internally mixed liquid morphology but was lower than aerosols with a thick viscous organic shell. The sensitivity cases performed with different phase-separation parameterization and dissolution rate of isoprene epoxydiol (IEPOX) into the particle phase in CMAQ can have varying impact on fine particulate matter (PM 2.5 ) organic mass, in terms of bias and error compared to field data collected during the 2013 SOAS. This highlights the need to better constrain the parameters that govern phase state and morphology of SOA, as well as expand mechanistic representation of multiphase chemistry for non-IEPOX SOA formation in models aided by novel experimental insights.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS2020

Robustness and Behavior of Adjoint Calculations of Observation Impacts in Numerical Weather Prediction

Adjoint models are powerful tools that can be used to estimate the impact of observations on a chosen norm for numerical weather prediction forecasts. In this study, the Global Modeling and Assimilation Office (NASA/GMAO) Observing System Simulation Experiment framework is employed to investigate the behavior of the adjoint tool in an environment where the 'true' state of the atmosphere is fully known. This allows for the calculation of adjoint estimates of observation impact for very short forecast times including the zero-hour analysis state. The adjoint calculations using self-analysis verification can also be compared to adjoint calculations using the 'truth' as verification in order to characterize the robustness of adjoint estimations in the operational setting. Results from a experiments exploring various aspects of performance of the adjoint tool will be presented.

Prive, Nikki C.↗
DOE OSTI2025

Full‐Waveform Simulation of Infrasound Propagation in the Atmosphere: A Case Study of the 2023 April 20 SpaceX Starship Explosion

Infrasound, low‐frequency sound below 20 Hz, has been a key technology to monitor explosion events in the atmosphere. The International Monitoring System (IMS) of the Comprehensive Nuclear‐Test‐Ban Treaty Organization provides the means for continuous monitoring of infrasonic events worldwide. Infrasonic techniques for event location and size estimation can also complement other observational techniques for the detection and characterization of the entry of asteroids or large meteoroids. In this study, we describe the detection capability of IMS infrasound stations for an explosive event in the middle of the atmosphere. Full‐waveform simulations are performed with the specification of atmospheric conditions and incorporated into the event location and explosion yield estimation. We applied it to the 2023 April 20 SpaceX Starship explosion at 29 km altitude. Starship is a super heavy‐lift space vehicle constructed by SpaceX and known as the largest and most powerful rocket ever built. The Starship explosion created huge pressure disturbances in the atmosphere, and its infrasound was detected by the IMS arrays in North America between 2000 and 4000 km. Independent observational data and available ground‐truth information provide a rare opportunity to evaluate the monitoring capability of the IMS network for elevated sources in the atmosphere. We also demonstrate the capability of full‐waveform simulation for infrasound wavefield characterization and prediction to improve event location and yield estimation.

Geosciences↗
DOE OSTI2024

A Stochastic Framework for Estimating Load Profiles at EV Fast Charging Stations

This paper formulates a methodology for estimating the average daily load profiles of EV fast charging stations over a planning horizon of five to ten years. The developed methodology uses historic vehicle registration data, state-level EV adoption targets, seasonal driving patterns, local demographics, competition, and traffic volume information to predict average station usage. Through Monte Carlo simulations, an average daily load profile is obtained for each month in the planning horizon, and prediction uncertainty is quantified. The proposed framework will facilitate the accurate estimation of energy and demand costs incurred by the charging station over the planning period, thereby informing return-on-investment calculations.

Biswas, Shuchismita↗