Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “polymer characterization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
DOE OSTI2019

Modification of rGO by B(C6F5)3 to generated single-site Lewis Acid rGO-O-B(C6F5)2 as coactivator of nickel complex, to produce highly disperse rGO-PE nanocomposite

We investigated the incorporation of reduced graphene oxide (rGO) into branched polyethylene, achieving nanocomposites with different rGO contents. The strategy included the direct reaction between B(C6F5)(3) (BCF) with rGO (reduced graphene oxide) and demonstrated by XPS, B-11, F-1(9) -MAS NMR, FT-IR the efficient modification of the rGO. The resulting solid contains sites -O-B(C6F5)(2 )capable of acting as co-catalysts in the activation of an (alpha-iminocarboxamidate)nickel (II) complex. The results show the efficient activation of this nickel catalyst through an exocyclic Lewis acid-base interaction and the subsequent ethylene polymerization. We achieved with this heterogeneous catalytic system activity greater than those previously reported for the BCF-Ni, homogenous system, while the characterization of the black colored polymer generated in situ, showed a complete delamination of the rGO. It became the first rGO-B(C6F5)(2) -Ni system fully characterized and capable of delaminate the rGO support by producing a nanocomposite rGO-LLDPE without loss of activity, compared to the homogeneous system. In addition, the polymer contains about 70% of methyl branches and a melting point higher than 125 degrees C.

In situ activation↗
NASA NTRS1990

Characterization of LaRC-TPI 1500 powders - A new version with controlled molecular weight

The crystallization behavior and the melt flow properties of two batches of 1500 series LaRC-TPI polymers have been investigated. The characterization methods include DSC, XRD, and melt rheology. The as-received materials posses initial crystalline melting peak temperatures of 295 and 305 C, respectively. These materials are less readily recrystallizable at elevated temperatures when compared to other semicrystalline thermoplastics. For the samples annealed at temperatures below 330 C, a semicrystalline polymer can be obtained. On the other hand, a purely amorphous structure is realized in samples annealed at temperatures above 330 C. The viscoelastic properties at elevated temperatures below and above T(g)s of the polymers were measured. Information with regard to the molecule sizes and distributions in these polymers were also extracted from melt rheology.

Hou, T. H.↗
NASA NTRS1990

Ladder polymers for use as high temperature stable resins or coatings

An object of the invention is to synthesize a new class of ladder and partial ladder polymers. In accordance with the invention, the new class of ladder and partial ladder polymers are synthesized by polymerizing a bis-dienophile with a bis-diene. Another object of the invention is to provide a fabricated, electrically conducting, void free composite comprising the new class of the ladder and partial ladder polymers described above. The novelty of the invention relates to a new class of ladder and partial ladder polymers and a process for synthesizing these polymers. These polymers are soluble in common organic solvents and are characterized with a unique dehydration property at temperatures of 300 to 400 C to provide thermo-oxidatively stable pentiptycene units along the polymeric backbone. These polymers are further characterized with high softening points and good thermo-oxidative stability properties. Thus these polymers have potential as processable, matrix resins for high temperature composite applications.

Meador, Mary Ann↗
DOE OSTI2026

Design, characterization and shape recovery behavior of 3D/4D printed shape memory polymers (SMPs)

Shape memory polymers (SMPs) represent a paradigm shift in material science, uniquely capable of undergoing reversible shape transformations triggered by external stimuli, positioning them as pivotal in developing next-generation biomedical devices, aerospace components, and adaptive structures. Extensive research has been done on SMPs with a major focus on high-temperature programming methods, which can limit energy efficiency and applicability with temperature-sensitive materials. Additionally, while various SMP blends have demonstrated great potential, limited work has been done on the suitability for 3D printing these materials, particularly under high-strain and ambient temperature programming conditions. In this study, a three-component optimized SMP composition was evaluated by 3D printing via the Material Extrusion (MEX) technique and investigating its ambient temperature-programming behavior at high strains. The SMP formulation studied was a tailored blend of thermoplastic polyurethane (TPU), polycaprolactone (PCL), and an octadecane diol-based copolymer (OBC) that exhibits robust shape memory behavior, high strain tolerance, and efficient force generation. Rigorous thermal, mechanical, and shape recovery analyses, along with optimized printing parameters and consistent shape recovery rates of up to 90%, were achieved under dynamic mechanical analysis (DMA), even under ambient programming conditions. This work demonstrates the SMP composition’s potential for adaptive, self-deployable systems with 4D printing characteristics ideal for bio-inspired structures and artificial muscle fibers.

Sudan, Kavish [University of Louisville, KY]↗
DOE OSTI2020

Plastic scintillators stable for operating in wide ranges of humidity and temperature variations

To provide efficient and reproducible response to nuclear radiation, scintillating plastics should be prepared as materials of high optical transparency and homogeneity that should remain intact during the lifetime of their operation. A problem with traditionally used polyvinyltoluene (PVT) or polystyrene (PS) plastic scintillators arises from their exposure to repeated large temperature swings that cause surface and volume defects, resulting in decreased sensitivity of the detection properties. We find that the problem can be avoided by composition modifications that enable preparation of plastics with properties that are resistant to the continuous variations in environmental conditions. This paper describes improvements in physical properties that can be achieved by the addition of crosslinkers (such as divinylbenzene, DVB) and oxygen-containing compounds or copolymers (e.g. polymethylamethacrylate, PMMA) to the traditional PVT or PS polymer matrices. Results of characterization show that the new materials can be prepared with the scintillation performance equal to that of commercial plastic scintillators, such as EJ-200.

36 MATERIALS SCIENCE↗
NASA NTRS2003

Characterizations of Enriched Metallic Single-Walled Carbon Nanotubes in Polymer Composite

Using different processing conditions, we disperse the single-walled carbon nanotube (SWNT) into the polymethyl methacrylate (PMMA) to form composites. In the melt-blended sample, the SWNTs originally semiconducting - became predominantly metallic after dispersion into the melt-blended composite. The interaction of the PMMA and SWNT is investigated by the polarized Raman studies. The structure changes in the PMMA and SWNT shows that the anisotropic interactions are responsible for SWNT electronic density of states (DOS) changes. The increased metallic SWNT percentage is confirmed by the conductivity and dielectric constant measurements .

Chen, Bin↗
NASA NTRS2003

Functionalization of Carbon Nanotubes

These project will explore the functionalization of carbon nanotubes via the formation of molecular complexes with perylene diimide based systems. It is anticipated that these complexes would be soluble in organic solvent and enable the homogenous dispersion of carbon nanotubes in polymer films. Molecular complexes will be prepared and characterized using standard spectroscopic and thermal analytical techniques. Polymer films will be prepared with these complexes and their properties (electrical and thermal conductivity, mechanical properties, stability) evaluated.

Webber, Stephen E.↗
NASA NTRS2014

Processing and Material Characterization of Continuous Basalt Fiber Reinforced Ceramic Matrix Composites Using Polymer Derived Ceramics.

The need for high performance vehicles in the aerospace industry requires materials which can withstand high loads and high temperatures. New developments in launch pads and infrastructure must also be made to handle this intense environment with lightweight, reusable, structural materials. By using more functional materials, better performance can be seen in the launch environment, and launch vehicle designs which have not been previously used can be considered. The development of high temperature structural composite materials has been very limited due to the high cost of the materials and the processing needed. Polymer matrix composites can be used for temperatures up to 260C. Ceramics can take much higher temperatures, but they are difficult to produce and form in bulk volumes. Polymer Derived Ceramics (PDCs) begin as a polymer matrix, allowing a shape to be formed and cured and then to be pyrolized in order to obtain a ceramic with the associated thermal and mechanical properties. The use of basalt in structural and high temperature applications has been under development for over 50 years, yet there has been little published research on the incorporation of basalt fibers as a reinforcement in the composites. In this study, continuous basalt fiber reinforced PDCs have been fabricated and tested for the applicability of this composite system as a high temperature structural composite material. The oxyacetylene torch testing and three point bend testing have been performed on test panels and the test results are presented.

Polymer Derived Ceramics↗
DOE OSTI2022

An Anthradithiophene Donor Polymer for Organic Solar Cells with a Good Balance between Efficiency and Synthetic Accessibility

Over the past few years, the organic photovoltaics technology (OPV) has reached remarkable power conversion efficiencies (PCEs), mostly thanks to the advent of nonfullerene acceptors as well as to a high level of materials engineering. Yet, the complex materials syntheses behind these results ultimately limit technological readiness. The quest for scalable organic compounds offering high PCE and reasonably low synthetic complexity is a must to close the gap between laboratory R&D and commercial products. The synthesis and full characterization of a new conjugated polymer called PATTD is reported herein, based on a novel anthradithiophene as an electron–rich building block coupled with a commercially available dithienylbenzodithiophenedione as an electron–withdrawing comonomer. Its photovoltaic properties are studied in blends with IT–4F and IDIC as acceptors. PATTD:IT–4F–based photovoltaic devices exhibit a PCE approaching 10% and over 2300 h shelf–life stability. Finally, the PATTD scalability factor (SF), together with the PATTD–based photovoltaic performances, lead to a PCE/SF value equal to 0.297, placing such devices into the innermost circle of OPV materials, achieving one of the best compromises between efficiency and synthetic complexity and at the same time offering promising industrial perspectives.

14 SOLAR ENERGY↗
NASA NTRS2001

A Sensitive Technique Using Atomic Force Microscopy to Measure the Low Earth Orbit Atomic Oxygen Erosion of Polymers

Polymers such as polyimide Kapton and Teflon FEP (fluorinated ethylene propylene) are commonly used spacecraft materials due to their desirable properties such as flexibility, low density, and in the case of FEP low solar absorptance and high thermal emittance. Polymers on the exterior of spacecraft in the low Earth orbit (LEO) environment are exposed to energetic atomic oxygen. Atomic oxygen erosion of polymers occurs in LEO and is a threat to spacecraft durability. It is therefore important to understand the atomic oxygen erosion yield (E, the volume loss per incident oxygen atom) of polymers being considered in spacecraft design. Because long-term space exposure data is rare and very costly, short-term exposures such as on the shuttle are often relied upon for atomic oxygen erosion determination. The most common technique for determining E is through mass loss measurements. For limited duration exposure experiments, such as shuttle experiments, the atomic oxygen fluence is often so small that mass loss measurements can not produce acceptable uncertainties. Therefore, a recession measurement technique has been developed using selective protection of polymer samples, combined with postflight atomic force microscopy (AFM) analysis, to obtain accurate erosion yields of polymers exposed to low atomic oxygen fluences. This paper discusses the procedures used for this recession depth technique along with relevant characterization issues. In particular, a polymer is salt-sprayed prior to flight, then the salt is washed off postflight and AFM is used to determine the erosion depth from the protected plateau. A small sample was salt-sprayed for AFM erosion depth analysis and flown as part of the Limited Duration Candidate Exposure (LDCE-4,-5) shuttle flight experiment on STS-51. This sample was used to study issues such as use of contact versus non-contact mode imaging for determining recession depth measurements. Error analyses were conducted and the percent probable error in the erosion yield when obtained by the mass loss and recession depth techniques has been compared. The recession depth technique is planned to be used to determine the erosion yield of 42 different polymers in the shuttle flight experiment PEACE (Polymer Erosion And Contamination Experiment) planned to fly in 2002 or 2003.

deGroh, Kim K.↗
DOE OSTI2020

CHARACTERIZATION ON ANISOTROPIC THERMAL CONDUCTIVITY FOR BIG AREA ADDITIVE MANUFACTURING WITH POLYMERS

Additive manufacturing with polymers has been used mainly for prototyping. A recent development of Big Area Additive Manufacturing (BAAM) at Oak Ridge National Laboratory has opened its applications in the mold and die industry. A numerical simulation and prediction for a mold heating performance requires accurate anisotropic thermal properties of the printed material, which are challenging to obtain, and often requires the use of multiple techniques. The transient plane source (TPS) technique has been widely used due to its ability to measure the thermal properties of an extensive range of materials (solids, liquids, powder). Despite the capability to characterize thermal conductivity k of isotropic and anisotropic materials, the measurements of latter materials are limited to the cases, where the samples have the same thermal conductivity k along x- and y-axis that form the radial plane. In this work, the method for a characterization of k in all three dimensions is developed, and the application of TPS is extended to the determination of thermal properties along the x-, y-, and z-axis individually. The materials are represented by additively manufactured polymers including polylactic acid (PLA) and styrene maleic anhydride (SMA). The developed method consists of (1) a determination of the heat capacity of the polymers by means of TPS in combination with the developed in this work data analysis procedure, (2) a machining three types of cylindrical samples from the same material, with the height corresponding either to x-, y-, or z-direction of printing, and (3) a determination of axial thermal conductivity employing anisotropic model and using previously determined heat capacity

Trofimov, Artem↗
DOE OSTI2020

Dispersity-Driven Stabilization of Coexisting Morphologies in Asymmetric Diblock Copolymer Thin Films

Despite decades of research, characterization of the effects of polymer chain dispersity on the structural properties of block copolymer thin films remains challenging. Here we present an integrated experimental and modeling approach to characterize the morphology of thin films containing asymmetric diblock copolymers. Specifically, we used synergistic neutron reflectivity (NR) and self-consistent field theory (SCFT)-based modeling to realize unexpected morphology of thin films containing asymmetric copolymers. Using NR, a highly stable and reproducible mixed phase of coexisting cylinders and lamellar domains was discovered in asymmetric poly(deuterated-styrene-b-n butyl methacrylate) (dPS-PBMA) copolymer thin films containing 34% volume fraction of dPS. SCFT reveals how to obtain such a thermodynamically stable morphology in the presence of disperse majority block and asymmetric interactions of polymer species with surfaces. Stabilization of the coexisting domains is a consequence of the depth segregation based on chain-length distribution. The asymmetric chains microphase-separate into cylindrical domains close to the substrate and near-symmetric chains form lamellar domains at the air interface. In the absence of dispersity, the coexistence of cylindrical and lamellar domains is thermodynamically unstable because of the absence of depth segregation. Overall, such an effect of dispersity on diblock copolymer thin-film morphology reveals a unique and powerful strategy to create coexisting nanoscale domains and tailor properties of thin films.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Design and Characterization of Hybrid Multilayer Structures: Layer-by-Layer Growth of Polymer and Graphene Oxide Assemblies and Their Utility in Fuel Cell Applications

We report the layer-by-layer growth of poly- (ethylenimine) (PEI) that has been modified with sulfamate functionalities (S-PEI) using Zr 4+ -complexation interlayer linking chemistry. We have also deposited adlayers of graphene oxide (GO) that have been modified to possess sulfate functionalities (SGO), onto the S-PEI layers. The multilayer assemblies are formed with sulfamate/sulfate and sulfate/sulfate (S-PEI + S-GO) interlayer linking chemistry. In all cases the adlayer thickness is consistent with predictions based on van der Waals volume and/or molecular mechanics calculations. X-ray photoelectron spectroscopy (XPS) is used to characterize the Zr/S stoichiometry in the multilayer assembly. The utility of these hybrid multilayer structures is demonstrated in a Proton Exchange Membrane (PEM) fuel cell, where they are shown to reduce H 2 gas crossover by 15% with only a 12 nm thick layer.

fuel cell↗
NASA NTRS1991

Effects of LDEF flight exposure on selected polymer matrix resin composite materials

The characterization of selected graphite fiber reinforced epoxy and polysulfone matrix resin composites which received exposure to the LEO environment on the LDEF is reported. The changes in mechanical properties of ultimate tensile strength and tensile modulus for exposed flight specimens are compared to the three sets of control specimens. Marked changes in surface appearance are discussed, and resin loss is reported. The chemical characterization including IR, thermal, and selected solution property measurements showed that the molecular structure of the polymeric matrix had not changed significantly in response to this exposure.

Slemp, Wayne S.↗
NASA NTRS1992

Effects of LDEF flight exposure on selected polymer matrix resin composite materials

The characterization of selected graphite fiber reinforced epoxy (934 and 5208) and polysulfone (P1700) matrix resin composites materials which received over five years and nine months of exposure to the low earth orbit (LEO) environment in experiment AO134 on the Long Duration Exposure Facility is reported. The changes in mechanical properties of ultimate tensile strength and tensile modulus for exposed flight specimens are compared to the three sets of control specimens. Marked changes in surface appearance are discussed, and resin loss is reported. The chemical characterization including infrared, thermal, and selected solution property measurements showed that the molecular structure of the polymetric matrix had not changed significantly in response to this exposure.

Slemp, Wayne S.↗
NASA NTRS2004

Characterization of bending EAP beams

Electroactive polymers are attractive actuation materials because of their large deformation, flexibility, and lightweight. A CCD camera system was constructed to record the curved shapes of bending during the activation of EAP films and image-processing software was developed to digitize the bending curves. A computer program was developed to solve the invese problem of cantilever EAP beams with tip position limiter. using the developed program and acquired curves without tip position limiter as well as the corresponding tip force, the EAP material properties of voltage-strain sensitivity and Young's modulus were determined.

large deformation↗