Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “polyesters”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17

SDU6 Interior Liner Testing & Evaluation

Two liner materials (Marseal® M-3500 and REMA Chemoline® 4CN) proposed for use as a liner inside the Saltstone Disposal Unit 6 (SDU6) were subjected to specific ASTM tests (tensile and lap-shear) after immersion in 50% and 100% simulant solutions for 1000 hours at the Savannah River Ecology Laboratory. Both liner materials exhibited good resistance to the simulant chemistry, at least based on the tests performed and the test duration/conditions imposed. In lap-shear tests, both materials failed in the base material rather than peeling apart, confirming good adhesion. The REMA 4CN bromobutyl elastomer showed superior bonding characteristics and absence of warping or delamination at the conditions tested. The Marseal M-3500 material (PVC/EVA blend with polyester reinforcement) exhibited deformation and debonding in some locations. The cause of the deformation and delamination observed in the Marseal M-3500 material is not fully known, but possibly attributed to thermomechanical stress at immersion temperatures, and the thermoplastic nature of the material. The immersion temperature (68 °C) is slightly greater than the maximum use temperature limit quoted for the Marseal M- 3500 liner (65 °C), though the basis for the service limit is unknown. The testing performed was limited in scope and only for these two liner materials. These tests were primarily performed to screen for severe incompatibility or short-term degradation in Saltstone bleedwater simulants at bounding solution temperatures. Additional testing is recommended to assess long-term performance and the overall service life of the liner.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Catalytic Upgrading of Key Biorefining Building Blocks to Renewable Chemicals, Polymeric Materials, and Liquid Fuels

The central objective of this project is to develop efficient, selective, and cost-effective catalytic systems for upgrading of key biorefining building blocks derived from catalytic conversion of plant biomass into value-added chemicals, polymeric materials, and liquid fuels. More specifically, the proposed work for the current grant period seeks to accomplish the following three specific objectives: (a) developing cost-effective and recyclable catalysts for selective upgrading (direct coupling) of the C 6 biorefining building block 5-hydroxymethylfurfural (HMF) into C 12 intermediates and for integrating biomass conversion and upgrading processes; (b) transforming the upgraded C 12 intermediates into polyols, polyurethanes, polyesters, and diesel fuels; and (c) reforming the upgraded intermediates into premium C 12 centered liquid hydrocarbon transportation fuels via selective hydrodeoxygenation catalysis.

09 BIOMASS FUELS↗

A Novel Process for Converting Coal to High-Value Polyurethane Products

Battelle has demonstrated a patented process for making high-value, polyurethane (PU) foam from coal, based on preparing liquefied coal via direct liquefaction, converting it to polyols as an intermediate via ozonation, and then making PU foams from these polyols. This process represents a breakthrough in innovative utilization of U.S. coals, and is applicable to bituminous as well as sub-bituminous coals. The resulting PU foam products are projected to have an extremely high value (i.e., over $\$5,000$ /ton), with nearly 100% of carbon utilization from coalderived liquid feedstock, and 31.5% to 43.5% of the carbon in the PU foam polyol product being bio-based. The targeted products represent an extremely large (i.e., over $80 billion/year), existing PU foam market, which could expand into making coatings and adhesives. The process can further help reduce petroleum imports, while improving the economics of PU foam production. This work was completed with funding from the National Energy Technology Laboratory (NETL), with cost share from the State of Ohio’s Ohio Development Services Agency (ODSA) and others, and has advanced the process to 10 kg/day continuous scale and thus to Technology Readiness Level (TRL) 5. A total of 48 coal-based polyols were prepared and evaluated. The initial 28 polyols focused on range finding for ideal conditions. The later 20 polyols were produced as part of process optimizations. These optimizations were targeted around a continuous ozonolysis process to evaluate extended time reactions and to create the necessary intermediate for production of 1-gallon samples of polyol. The most unique attribute of Battelle’s polyol is in the utilization of coal’s aromaticity to gain final foam rigidity. Typically, polyols depend on the isocyanate fraction and cross-linking to gain rigidity. By utilizing coal, we were able to maintain rigidity while reducing the overall hydroxyl value of the polyol. This is important as lower hydroxyl value leads to greater percent weight of the coal-based polyol because less isocyanate is required for foaming. This leads to greater foam cost savings. This report provides the details, process, and process cost models of the conversion of coal to polyols and further to PU foams. Battelle’s process begins with coal liquids. These liquids can be obtained by two processes: coal coking or pyrolysis to produce coal tar, and Battelle’s biobased coal-to-liquids (CTL) process to produce heavy syncrude after liquifying >85% coal. After liquification, Battelle utilizes ozonolysis to create functionalization on the polyaromatic coal structure. The functionalization is then converted to the final polyester polyol through transesterification, or to hydroxyamide polyol through amidification. Equivalent or better standard properties have been obtained for 2 lb/ft 3 density rigid, water and freon-alternative blown foams, including compressive strength, density, R-value, and dimensional stability. Target applications for these foams are insulation, packaging, and energy-absorbing foams. Some exploratory testing also showed promise for adhesives applications. A detailed economic analysis showed that Battelle’s polyol process is economical, at a 140 metric tons per day (MTD) polyol production scale. An attractive return on investment (ROI) at competitive pricing validates the process is ready for a pilot-plant demonstration. A scale-up plan is provided.

01 COAL, LIGNITE, AND PEAT↗

Resource Recovery and Environmental Protection in Wyoming’s Greater Green River Basin Using Selective Nanostructured Membranes (Final Report)

Produced water (PW) represents a sizable waste stream that is co-generated with oil and natural gas production. In 2021 Wyoming ranked 8th and 9th, respectively in domestic oil and natural gas production. In 2017 Wyoming ranked as the 4th highest generator of PW in the U.S, accounting for 7% of the total volume generated. In the context of being the 3rd most arid state in the U.S., the value of water reuse becomes obvious. PW reuse, and resource recovery, in any form requires some level of treatment to remove particulates, residual (free, dispersed) hydrocarbons, organics, and salts. The level of treatment depends on the requirements of the reuse, or resource recovery, application. PW management systems in Wyoming employ in order of volume of PW managed the following management strategies: reinjection for enhanced oil recovery, surface discharge, deep well injection, evaporation ponds (impoundments), and commercial management/treatment. Complicating treatment efforts are the relatively high concentrations of organics (natural and synthetic), dispersed/free hydrocarbons, benzene-toluene-ethylbenzene, and xylenes (BTEX) compounds, biologicals, salts, and minerals. Hydrocarbons (dispersed/dissolved crude oils) and BTEX compounds, as well as synthetic organics, present economic and environmental concerns. The former represents lost revenue, while the latter results in negative environmental impacts like emissions from surface impoundments. The overall objective of this proposal was to synthesize superhydrophilic/oleophobic and superhydrophobic/oleophilic membranes for selectively concentrating and then separating BTEX compounds and oil and grease (O&G) from PW originating from the Greater Green River Basin (GGRB) in Wyoming. Three specific research aims were pursued to accomplish this overall objective. This final report details the development of the superhydrophobic and superhydrophilic membranes, as well as the design of the membrane module prototypes specifically. The technoeconomic assessment is separately reported in another document. 1. Aim #1 – Material optimization and performance evaluation of superhydrophilic/oleophobic and superhydrophobic/oleophilic membranes made by electrospinning/spraying. 2. Aim #2 – Design and construction of cross-flow membrane modules for selectively concentrating and then separating BTEX/oil from GGRB produced water. 3. Aim #3 – Techno-economic assessment of BTEX/oil recovery, and clean water production, using superhydrophilic/oleophobic and superhydrophobic/oleophilic membrane separation for GGRB PW. Superhydrophobic membranes were synthesized by electrospinning poly(vinylidene fluoride-co-hexafluoropropylene) (PVDF-HFP) nanofibers onto polyester (PET) substrates and electrospraying nano-carbon black/PVDF-HFP onto the nanofibrous layer. These membranes were characterized by high (>8000 liters per square meter per hour per bar (LMH/bar)) permeance values for pure hydrocarbon phases and a high hydrocarbon selectivity (>96%) when treating GGRB PW. All results were obtained when operating the membrane in a crossflow configuration representative of actual field operating conditions. Solvent/oil properties, specifically viscosity and total surface energy/tension, affected permeance across the membrane, which resulted in light mineral oil (394 LMH/bar) and o-xylene (1834 LMH/bar) being characterized by lower permeance values in the pure phase tests. Mixed phase fluxes between 40 to 80 LMH were obtained for the PW when operating the membrane at a feed pressure of 0.3 bar. Flux decreased as the mixed phase concentration in the feed decreased pointing to the importance of maximizing the collision efficiency between the emulsion and the membrane surface and maximizing the emulsion concentration in the feed and the turbulence within the feed channel. These tests demonstrated that the superhydrophobic membranes developed here are a viable hydrocarbon recovery method for GGRB PWs and should be pursued for testing in pilot-scale trials. Superhydrophilic membranes were successfully synthesized via electrospinning/spraying using polyacrylonitrile (PAN) nanofibers as a base nanofibrous matrix. Integration of polyaniline (PANI) into the nanofibrous matrix produced a superior membrane, for water filtration applications, relative to PAN alone and reduced graphene oxide (RGO) when integrated into the nanofibrous matrix. This conclusion was based on the PANI-PAN resistance to flux loss (fouling) when treating model solvent/oil solutions representative of GGRB PWs and field collected PW from the GGRB. The synthesized PAN membranes outperformed a commercially available PAN membrane designed for oil/water separation. This finding indicates that the surface chemical and physical characteristics of the electrospun membranes presents improved properties for filtration of challenging waters like GGRB PWs. The electrospun membranes therefore show promise overall as a substitute for conventionally polymerized membranes in PW treatment applications. The PANI-PAN membrane specifically presents superior performance characteristics for concentration O&G prior to treatment by the hydrocarbon recovery membrane and producing high-quality filtrate for reuse and/or additional treatment (desalination).

02 PETROLEUM↗

Social Acceptance of a Reduced-Footprint Synthetic Mooring System for Floating Offshore Wind Turbines in the Gulf of Maine

Engineers are looking to reduce the size of floating offshore wind mooring footprints to minimize conflict with other ocean users. To this end, the University of Maine (UMaine) received funding from the United States Department of Energy (DOE) to design, demonstrate, and validate a novel reduced-footprint synthetic mooring system for floating offshore wind turbines (FOWTs) that reduces impacts to fisheries and the levelized cost of energy. UMaine designed two mooring systems for the New England Aqua Ventus (NEAV) I demonstration project to quantify the technical, economic, and social impacts of a reduced-footprint hybrid mooring system. Specifically, a traditional catenary chain mooring system and a novel polyester rope-chain hybrid system were designed to the front-end engineering design level for this assessment. The National Renewable Energy Laboratory (NREL) was funded by DOE to help independently quantify the social and techno-economic impacts of the rope-chain hybrid mooring system designed by UMaine. This report focuses on NREL's assessment of the social acceptance of the reduced-footprint rope-chain hybrid mooring system and the conventional all-chain mooring system by competing users in the Gulf of Maine.

ENGINEERING,WIND ENERGY↗

End-Use Savings Shapes Measure Documentation: Window Film

This documentation focuses on a single end-use savings shape measure - window film. The window film studied in this analysis, called solar control film, is a passive retrofit solution for windows that does not involve window replacement. This type of film is composed of transparent, tinted, or metalized laminated polyester layers and can be attached to an existing window surface (either on the exterior or interior side of the window). The properties of the window film are designed to shift the thermal and optical performances of the overall glazing system in order to serve various needs the customer would have (e.g., heat, glare). While the practical goal of purchasing and installing a window film varies widely in the real market, this study only focuses on the goal of energy savings, and highlighting the corresponding emissions. Other important aspects that customers typically consider include visual comfort, privacy, aesthetics, ultraviolet protection, etc. Thus, in practice, customers often choose a window film product not only to save energy (or cost) but also to mitigate issues around glare, excessive light, daytime privacy, or inconsistent appearance of the building. Window film products that were modeled in this analysis significantly reduced the solar heat gain coefficient of the overall glazing system, resulting in better energy savings for buildings in hot climate regions. However, significantly reducing the solar heat gain coefficient that can block unfavorable heat during the summer can actually harm blocking favorable heat during the winter. By applying window films on a stock of buildings covering various load and weather conditions, this analysis highlights when (e.g., time of day) and where (e.g., geospacial location) we can save energy with window films.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Green Biodegradation: Analysis of Potential Polyurethane-degrading Enzymes and Their Secretion in Chlamydomonas reinhardtii

Plastic pollution is a critical global issue, with only 5% of plastics currently recycled. Polyester polyurethane (PU), a widely used plastic, can potentially be broken down using enzymatic biodegradation rather than mechanical processing that generates microplastics. This study focuses on PS5, a potential PU-degrading enzyme with esterase activity, capable of cleaving ester bonds found in PU structures. Researchers investigated the expression and secretion of PS5 in the green microalga Chlamydomonas reinhardtii, a sustainable production platform capable of generating PU precursors such as lipids and diacids while sequestering carbon. Experiments demonstrated that PS5 significantly outperformed commercial lipase in cleaving the FDA substrate, indicating high esterase activity. Algal transformants expressing PS5 also showed halo formation on Impranil®-agar plates, suggesting PU dispersion degradation. These findings highlight C. reinhardtii as a viable chassis for the production and secretion of plastic-degrading enzymes, offering a sustainable route to both upcycle and degrade PU products at the end of their lifecycle.

Diaz, Crisandra Jade↗

SELKIE Spectral Extraction Results

This document describes results from the WAMOR Chesapeake Bay collection in October 2024, a data collection from the Arkeus HSOR hyperspectral sensor. The calibration array was staged at USCG Station Little Creek, Virginia. With the provided HSOR imagery and data, our analysis does not show a capability to effectively detect materials of interest from non-materials of interest as well as differentiate materials of interest from each other, the materials of interest being polypropylene, polyester, and cotton. The fundamental reasons are (1) the spectral bands of HSOR do not reside in specific wavelength locations to allow for material identification and (2) the provided imagery appears to not have consistent band-to-band relationships indicative of a lack of calibration (gain/offsets) or some other calibration issues. With regard to analyzing a subset of the delivered HSOR, HSOR can make general statements about materials not being water and have the capability to make color assessments.

36 MATERIALS SCIENCE↗

Degradable Biocomposite Thermoplastic Polyurethanes

In this project, the team developed tough and degradable biocomposite thermoplastic polyurethanes (TPUs) by incorporating bacterial spores into TPUs as a biofunctional living filler. The team screened various bacteria and selected the Bacillus subtilis ATCC 6633 strain as the final candidate, primarily due to its genomic availability, sporulation ability and TPU assimilation activity. The heat-shock tolerance of ATCC 6633 spores was further improved through evolutionary engineering via Adaptive Laboratory Evolution (ALE), demonstrating a 17.7-fold enhanced germination efficiency post heat-shock treatment compared to the wild-type strain (WT). The team fabricated biocomposite TPUs by incorporating lyophilized powder of heat-shock tolerized (HST) spores during the hot melt extrusion (HME) of TPU at 135 °C. The baseline TPU used in this project is a commercially available soft-grade TPU (BCF45) manufactured by BASF. Colony forming unit (CFU) assays quantified that WT and HST spores in the TPU matrix retained approximately 20% and 100% survivability, respectively, after HME. Tensile testing demonstrated that the spores behaved as a polymer-reinforcing filler, positively affecting the overall tensile properties of the biocomposite TPU. For example, biocomposite TPU with WT and HST spores (BC TPU WT and BC TPU HST , respectively) exhibited up to 25% and 37% improved toughness, respectively, compared to TPU without spores. BC TPU HST showed remarkably improved disintegration in autoclaved compost (92% mass loss in 5 months), which simulated a microbially poor environment for TPU degradation. When compared to TPU without spores (44% mass loss in 5 months) the acceleration of degradation is marked. Respirometry confirmed that 72% of BC TPU HST was biomineralized into CO2 within 6 months, indicating that spores in the biocomposite TPU were germinated by utilizing nutrients in the autoclaved compost, facilitating TPU degradation at the end of the material's life. The team demonstrated the scale-up of biocomposite TPU fabrication using continuous extrusion and injection molding techniques. Processing conditions optimized in a lab-scale microcompounder were successfully transferred to a continuous extruder with a 30-fold increased throughput. Biocomposite TPUs prepared using these industry-relevant processes showed comparable toughness improvements to samples prepared in the lab-scale extruder. Excitingly, following compounding in the pilot-extruder the composite material could be injection molded, while retaining high spore viability and similar toughness improvements. The team also found that spores in biocomposite TPU served as antioxidants, preventing toughness decay during the recycled extrusion of BC TPU HST . Long-term storage tests over one year showed that the addition of spores had no negative effect on the longevity of the TPU. Furthermore, the team demonstrated the fabrication of spore-bearing biocomposite polymers with other polyesters such as PBAT, PLA, and PCL. We obtained promising preliminary data that showed overall toughness improvements for all polymers with spore addition. Finally, life cycle assessment (LCA) and techno-economic analysis (TEA) were carried out, which indicated minimal additional cost of fabrication. Overall, a tough and degradable biocomposite thermoplastic was successfully developed through this project, with all tasks completed successfully, achieving >100% of the objectives.

36 MATERIALS SCIENCE↗

Optimizing enzymes for plastic upcycling using machine learning design and high throughput experiments

Plastic use is ubiquitous in the modern world, and polyethylene terephthalate (PET) is one of the most abundantly produced plastics (and the most highly produced polyester), with ~65 million metric tons manufactured annually. To the consumer, PET is likely most recognizable as the plastic used to make beverage bottles. Like many plastics, traditional mechanical or chemical means of PET deconstruction and upcycling are costly and inefficient. Because of these challenges, recycled plastic is generally of lower quality and is more expensive to produce than virgin plastic derived from petroleum. Ultimately, this results in most plastic ending up as waste. We view plastic waste as an underutilized resource which, with the development of more efficient and high-quality recycling processes, could (1) generate significant economic value while (2) decreasing petroleum usage and greenhouse gas emissions, as well as (3) minimizing its negative environmental and health impacts. Biocatalytic recycling, or biomanufacturing the basic building blocks of new plastic from plastic waste, is a promising approach to plastic reuse that complements existing recycling technologies. Recently, biological enzymes capable of breaking down PET have garnered significant attention as an attractive means of dealing with the plastic problem. These enzymes are currently undergoing pilot studies for implementation in industrial-scale enzyme-based recycling. However, there are significant limitations to current enzymes, including the need to perform costly pre-processing of the plastic waste before the enzymes are able to work. Further optimization of these enzymes is necessary to make these technologies competitive, and ultimately incentivise industry-wide adoption of this biology-based green recycling technology. n this work we demonstrate a means to design and generate performant biological enzymes, capable of efficiently deconstructing plastic waste. Specifically, we applied recent advances in artificial intelligence, machine learning, and statistical analysis to design new versions and discover natural enzymes capable of breaking down PET. We focused on optimizing key properties that are important for industrial-scale enzymatic recycling such as pH and thermotolerance. Normal testing of enzymatic plastic-deconstruction is extremely labor intensive and so through this work we also developed a robotic-assisted experimental pipeline capable of characterizing thousands of candidate enzymes. The results of this iterative, AI-guided, multi-discipline approach have led to increases in enzymatic breakdown of over 150X over starting enzymes. This work supports the rapidly developing and transformative field of biocatalytic solutions to environmental problems beyond the discovery and predictive understanding of enzymes for polymer recycling, and has wide implications for tackling numerous energy problems such as carbon capture and fixation (e.g., engineering carbon monoxide dehydrogenase and the rubisco-pathway), biomining (e.g., design of lanthanide-binding proteins) and biomanufacturing (e.g., lignin-deconstruction enzymes).

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Plastic from CO2 and Inedible Biomass (CRADA Final Report)

As part of the Cyclotron Road program, ReSource Chemical Corp. sought to investigate the conversion of inedible biomass and CO₂ to FDCA. FDCA is a performance monomer widely viewed as a green replacement for the petroleum-derived monomer PTA, which is produced at approximately 60 Mt per year with over 100 Mt of annual GHG emissions. The major polyester made from PTA, called PET, is a >$\$$100B industry with applications in bottling, food packaging, and fibers. The FDCA analogue of PET, called PEF, had superior gas barrier, mechanical, and thermal properties that enable increased shelf life of perishable goods while using less plastic.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

SMC Reinforced by Recycled or Textile Carbon Fiber

There is a significant need to expand material options for SMC that has traditionally used glass fibers for decades. There are several integral issues related to chopping and conveying a range of materials including glass, carbon, basalt, thermoplastic tapes, and recycled fibers. These are in a variety of forms including continuous tows, discontinuous agglomerates such as pyrolyzed carbon fibers that could be used to produce a range of SMC intermediates. Standard/conventional SMC processing is limited to cutting rotors specifically for glass and compounding with thermoset polyesters and some epoxies. The multi-material, multi-format line developed in this project is flexible to enable custom conveying and uses an interchangeable rotor dedicated for specific material types. The overall tasks undertaken in this project included: evaluation of the fiber feed mechanism, effect of textile grade carbon, evaluating servo motor controlling of conveyor, evaluate doctor box resin feed, evaluate compaction unit, evaluation of different formulations, and develop automation such as PLC programming. The new multi-material SMC line Version 2 (SCM-V2) incorporated servo motors over induction motors which gave the overall cutter system precision control and made it quiet. The addition of a 14-roll compaction unit at the end of the line in SMC-V2 enabled higher material wet out which was a limitation in the SMC Version 1 (SMC-V1). The cutters were further updated to reduce the cantilever overhang of the fiber which enabled more uniform cut lengths for glass, carbon, and basalt fibers. The overall instrumentation and system control including a remote control operation was enabled in the SMC-V2. The line speed is capable of 10-20 ft/minute. The cutting modules were designed and engineered for cutting glass, basalt and textile grade carbon in 300k and 450-600k format widths. The cutting trials were established for a range of fiber types. The study also demonstrated the utility of the line to cut and produce basalt fiber SMC. Initial trials were conducted on the properties from recycled carbon fiber (rCF) mats in epoxy resin. Overall, the Covid19 situation constrained the team from accessing the SMC line for over 18 months. Despite this challenge major advancements were made.

36 MATERIALS SCIENCE↗

Biodegradable Biocomposite Development for Large Scale Additive Manufacturing

Oak Ridge National Laboratory (ORNL) worked with Mitsubishi Chemical America, Inc. to develop a highly biodegradable ~100% biobased feedstock for large format additive manufacturing (AM). Together, they developed an AM feedstock based on the biobased polyester, polybutylene succinate (PBS), that is typically used in agriculture and packaging projects. The motivation for this work was to leverage the high degradability of this polymer in AM to create a new avenue for end-of-life disposal of the product. A composite feedstock was developed from PBS, polylactic acid (PLA), and wood flour (WF). While WF improves printability, reduces feedstock cost, and can improve stiffness, it also often results in a loss in tensile strength which can inhibit/limit applications of the material. To recover the loss in tensile strength suffered by including large quantities, up to 30 wt.% WF in the composite, a chain extender was used to compatibilize the different composite constituents with each other. The feedstock was used to 3D-print a demonstration mold for precast concrete catch basins and was tested by casting 750 lbs of concrete. The mold survived the demonstration. Aerobic degradation testing of the composite feedstock showed that it was highly degradable, 40% biodegradation after 90 days, compared to other incumbent biobased feedstocks.

100% biobased feedstock for large format additive ↗

Biodegradable Biocomposite Development for Large Scale Additive Manufacturing

Oak Ridge National Laboratory (ORNL) worked with Mitsubishi Chemical America, Inc. to develop a highly biodegradable ~100% biobased feedstock for large format additive manufacturing (AM). Together, they developed a AM feedstock based on the biobased polyester, polybutylene succinate (PBS), that is typically used in agriculture and packaging projects. The motivation for this work was to leverage the high degradability of this polymer in AM to create a new avenue for end-of-life disposal of the product. A composite feedstock was developed from PBS, polylactic acid (PLA), and wood flour (WF). While WF improves printability, reduces feedstock cost, and can improve stiffness, it also often results in a loss in tensile strength which can inhibit/limit application of the material. To recover the loss in tensile strength suffered by including large quantities, up to 30 wt%, WF in the composite a chain extender was used to compatibilze the different composite constituents with each other. The feedstock was used to 3D-print demonstration mold for precast concrete catch basins and was tested by casting 750 lbs of concrete. The mold survived the demonstration. Aerobic degradation testing of the composite feedstock showed that it was highly degradable, 40% biodegradation after 90 days, compared to other incumbent biobased feedstocks.

36 MATERIALS SCIENCE↗

EFFECTS OF TRITIUM GAS EXPOSURE ON ELECTRICALLY CONDUCTING POLYMERS

Effects of beta (tritium) and gamma irradiation on the surface electrical conductivity of two types of conducting polymer films are documented to determine their potential use as a sensing and surveillance device for the tritium facility. It was shown that surface conductivity was significantly reduced by irradiation with both gamma and tritium gas. In order to compare the results from the two radiation sources, an approximate dose equivalence was calculated. The materials were also sensitive to small radiation doses (<10{sup 5} rad), showing that there is a measurable response to relatively small total doses of tritium gas. Spectroscopy was also used to confirm the mechanism by which this sensing device would operate in order to calibrate this sensor for potential use. It was determined that one material (polyaniline) was very sensitive to oxidation while the other material (PEDOT-PSS) was not. However, polyaniline provided the best response as a sensing material, and it is suggested that an oxygen-impermeable, radiation-transparent coating be applied to this material for future device prototype fabrication. A great deal of interest has developed in recent years in the area of conducting polymers due to the high levels of conductivity that can be achieved, some comparable to that of metals [Gerard 2002]. Additionally, the desirable physical and chemical properties of a polymer are retained and can be exploited for various applications, including light emitting diodes (LED), anti-static packaging, electronic coatings, and sensors. The electron transfer mechanism is generally accepted as one of electron 'hopping' through delocalized electrons in the conjugated backbone, although other mechanisms have been proposed based on the type of polymer and dopant [Inzelt 2000, Gerard 2002]. The conducting polymer polyaniline (PANi) is of particular interest because there are extensive studies on the modulation of the conductivity by changing either the oxidation state of the main backbone chain, or by protonation of the imine groups [de Acevedo, 1999]. There are several types of radiation sensors commercially available, including ionization chambers, geiger counters, proportional counters, scintillators and solid state detectors. Each type has advantages, although many of these sensors require expensive electronics for signal amplification, are large and bulky, have limited battery life or require expensive materials for fabrication. A radiation sensor constructed of a polymeric material could be flexible, light, and the geometry designed to suit the application. Very simple and inexpensive electronics would be necessary to measure the change in conductivity with exposure to radiation and provide an alarm system when a set change of conductivity occurs in the sensor that corresponds to a predetermined radiation dose having been absorbed by the polymer. The advantages of using a polymeric sensor of this type rather than those currently in use are the flexibility of sensor geometry and relatively low cost. It is anticipated that these sensors can be made small enough for glovebox applications or have the ability to monitor the air tritium levels in places where a traditional monitor cannot be placed. There have been a few studies on the changes in conductivity of polyaniline specifically for radiation detection [de Acevedo, 1999; Lima Pacheco, 2003], but there have been no reports on the effects of tritium (beta radiation) on conducting polymers, such as polyaniline or polythiophene. The direct implementation of conducting polymers as radiation sensor materials has not yet been commercialized due to differing responses with total dose, dose rate, etc. Some have reported a large increase in the surface conductivity with radiation dose while others report a marked decrease in conductive properties; these differing observations may reflect the competing mechanisms of chain scission and cross-linking. However, it is clear that the radiation dose effects on conducting polymers must be fully understood before these materials can be used as sensing devices. This report presents the results of irradiations of two conductive polymers: polyaniline and polythiophene. Samples of doped polyaniline and polythiophene were coated onto polyester (polyethyleneterephalate, PET) substrates and were exposed to both tritium gas (beta irradiation) and {sup 60}Co gamma irradiation. The samples were subsequently characterized after various total doses. Infrared spectroscopy was utilized to characterize the gamma-exposed samples post-irradiation. Although the sources of radiation are different in kind (charged particle versus photon) and their energies differ, there will be great value in using noncontaminating gamma irradiation to model the effects of tritium beta radiation.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Investigation of IAQ-Relevant Surface Chemistry and Emissions on HVAC Filter Materials

Chemical reactions involving ozone of outdoor origin and indoor materials are known to be significant sources of formaldehyde and other irritant gas-phase oxidation products in the indoor environment. HVAC filters are exposed to particularly high ozone concentrations--close to outdoor levels. In this study, we investigated chemical processes taking place on the surface of filters that included fiberglass, polyester, cotton/polyester blend and synthetic (e.g., polyolefin) filter media. Ozone reactions were studied on unused filter media, and on filters that were deployed for 3 months in two different locations: at the Lawrence Berkeley National Laboratory and at the Port of Oakland. Specimens from each filter were exposed to ozone under controlled conditions in a laboratory flow tube at a constant flow of dry or humidified air (50percent relative humidity). Ozone was generated with a UV source upstream of the flow tube, and monitored using a photometric detector. Ozone breakthrough curves were recorded for each sample exposed to ~;;150 ppbv O3 for periods of ~;;1000 min, from which we estimated their uptake rate. Most experiments were performed at 1.3 L/min (corresponding to a face velocity of 0.013 m/s), except for a few tests performed at a higher airflow rate, to obtain a face velocity of 0.093 m/s, slightly closer to HVAC operation conditions. Formaldehyde and acetaldehyde, two oxidation byproducts, were collected downstream of the filter and quantified. Emissions of these volatile aldehydes were consistently higher under humidified air than under dry conditions, at which levels were near the limit of detection. Our results confirm that there are significant reactions of ozone as air containing ozone flows through HVAC filters, particularly when the filters are loaded with particles and the air is humidified. The amount of ozone reacted was not clearly related to the types of filter media, e.g., fiberglass versus synthetic. Specific fiberglass filters that were coated with an impaction oil showed significantly higher formaldehyde emissions than most other samples. Those emissions were magnified in the presence of particles (i.e., in used filters), and were observed even in the absence of ozone, which suggests that hydrolysis of filter binder or tackifier additives may be the reason for those high emissions. Mass balance calculations indicate that the emission rates of formaldehyde and acetaldehyde from the filters are generally not large enough to substantially increase indoor formaldehyde or acetaldehyde concentrations.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Final report : multicomponent forensic signature development : interactions with common textiles; mustard precursors and simulants.

2-Chloroethyl phenyl sulfide (CEPS), a surrogate compound of the chemical warfare agent sulfur mustard, was examined using thermal desorption coupled gas chromatography-mass spectrometry (TD/GC-MS) and multivariate analysis. This work describes a novel method of producing multiway data using a stepped thermal desorption. Various multivariate analysis schemes were employed to analyze the data. These methods may be able to discern different sources of CEPS. In addition, CEPS was applied to cotton, nylon, polyester, and silk swatches. These swatches were placed in controlled humidity chambers maintained at 23%, 56%, and 85% relative humidity. At regular intervals, samples were removed from each test swatch, and the samples analyzed using TD/GC-MS. The results were compared across fabric substrate and humidity.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗

New Transposon Tools Tailored for Metabolic Engineering of Gram-Negative Microbial Cell Factories

Re-programming microorganisms to modify their existing functions and/or to bestow bacteria with entirely new-to-Nature tasks have largely relied so far on specialized molecular biology tools. Such endeavors are not only relevant in the burgeoning metabolic engineering arena but also instrumental to explore the functioning of complex regulatory networks from a fundamental point of view. À la carte modification of bacterial genomes thus calls for novel tools to make genetic manipulations easier. We propose the use of a series of new broad-host-range mini-Tn5-vectors, termed pBAMDs, for the delivery of gene(s) into the chromosome of Gram-negative bacteria and for generating saturated mutagenesis libraries in gene function studies. These delivery vectors endow the user with the possibility of easy cloning and subsequent insertion of functional cargoes with three different antibiotic-resistance markers (kanamycin, streptomycin, and gentamicin). After validating the pBAMD vectors in the environmental bacterium Pseudomonas putida KT2440, their use was also illustrated by inserting the entire poly(3-hydroxybutyrate) (PHB) synthesis pathway from Cupriavidus necator in the chromosome of a phosphotransacetylase mutant of Escherichia coli. PHB is a completely biodegradable polyester with a number of industrial applications that make it attractive as a potential replacement of oil-based plastics. The non-selective nature of chromosomal insertions of the biosynthetic genes was evidenced by a large landscape of PHB synthesis levels in independent clones. One clone was selected and further characterized as a microbial cell factory for PHB accumulation, and it achieved polymer accumulation levels comparable to those of a plasmid-bearing recombinant. Taken together, our results demonstrate that the new mini-Tn5-vectors can be used to confer interesting phenotypes in Gram-negative bacteria that would be very difficult to engineer through direct manipulation of the structural genes.

60 APPLIED LIFE SCIENCES↗