Mass and phase spectrometry in modulated beam experiments
Modulated molecular beam mass and phase spectroscopy applications in hot oxygen radiative attachment, crossed beam chemical kinetics and neutrals clustering in free jets
Fite, W. L.↗
SEARCH · Engineering Papers
Results for “phase modulation”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Phase insensitive acoustoelectric transducer
Conventional ultrasonic transducers transform acoustic waves into electrical signals preserving phase and amplitude information. When the acoustic wavelength is significantly smaller than the transducer diameter, severe phase modulation of the electrical signal can occur. This results in anomalous attenuation measurements, background noise in nondestructive evaluation, and in general complicates data interpretation. This article describes and evaluates a phase-insensitive transducer based on the acoustoelectric effect. Theory of operation of the acoustoelectric transducer (AET) is discussed, and some optimization procedures outlined for its use. Directivity data for the AET are contrasted with a conventional piezoelectric transducer. In addition, transmission scanning data of phantom flaws in metal plates are presented for both transducers and demonstrate a significant improvement in resolution with the AET.
Heyman, J. S.↗
Multistage Estimation Of Frequency And Phase
Conceptual two-stage software scheme serves as prototype of multistage scheme for digital estimation of phase, frequency, and rate of change of frequency ("Doppler rate") of possibly phase-modulated received sinusoidal signal in communication system in which transmitter and/or receiver traveling rapidly, accelerating, and/or jerking severely. Each additional stage of multistage scheme provides increasingly refined estimate of frequency and phase of signal. Conceived for use in estimating parameters of signals from spacecraft and high dynamic GPS signal parameters, also applicable, to terrestrial stationary/mobile (e.g., cellular radio) and land-mobile/satellite communication systems.
Kumar, Rajendra↗
Characterization and QC practice of 16-channel ADC ASIC at cryogenic temperature for Liquid Argon TPC front-end readout electronics system in DUNE experiment
ColdADC is a low-noise 16-channel analog-to-digital converter ASIC designed for cold readout electronics of Liquid Argon Time Projection Chambers (LArTPCs) in the Deep Underground Neutrino Experiment (DUNE). ColdADC was specifically designed for operation at cryogenic temperatures (77 K–89 K). Cold electronics is considered to be an enabling technology for liquid argon detectors in neutrino experiments. The main function of the chip is to digitize signals from the 16-channel charge-sensitive amplifier designed at BNL (LArASIC) and send digitized signals to the data aggregator and serializer chip (COLDATA). ColdADC operates with a resolution of 12 bits and a sampling rate of 2 MS/s per channel. A complete characterization of prototype chips was conducted at cryogenic temperature, involving power consumption, noise and linearity performance. In the first DUNE Far-Detector module, 384000 data channels will be read out, corresponding to 24000 ColdADC chips. Therefore, systematic testing of ColdADC chips at cryogenic temperature is vital for the quality and reliability of DUNE Single-Phase modules. We have developed a Quality Control (QC) test stand that includes ColdADC evaluation and characterization at cryogenic temperature. The QC procedure was applied to a first batch of 33 chips, corresponding to 528 data channels. The obtained results meet all the required DUNE specifications for ColdADC. Moreover, the testing outcome allowed us to identify possibilities of performance optimization that are currently being addressed in the design of the next version of the chip. The Quality Control procedure is proved to be successful and will be a reference design for future large-batch production testing of final ColdADC ASICs.
46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
Quantum propagation in single mode fiber
This paper presents a theory for quantum light propagation in a single-mode fiber which includes the effects of the Kerr nonlinearity, group-velocity dispersion, and linear loss. The theory reproduces the results of classical self-phase modulation, quantum four-wave mixing, and classical solution physics, within their respective regions of validity. It demonstrates the crucial role played by the Kerr-effect material time constant, in limiting the quantum phase shifts caused by the broadband zero-point fluctuations that accompany any quantized input field. Operator moment equations - approximated, numerically, via a terminated cumulant expansion - are used to obtain results for homodyne-measurement noise spectra when dispersion is negligible. More complicated forms of these equations can be used to incorporate dispersion into the noise calculations.
Joneckis, Lance G.↗
High-Power, High-Speed Electro-Optic Pockels Cell Modulator
Electro-optic modulators rely on a change in the index of refraction for the optical wave as a function of an applied voltage. The corresponding change in index acts to delay the wavefront in the waveguide. The goal of this work was to develop a high-speed, high-power waveguide- based modulator (phase and amplitude) and investigate its use as a pulse slicer. The key innovation in this effort is the use of potassium titanyl phosphate (KTP) waveguides, making the highpower, polarization-based waveguide amplitude modulator possible. Furthermore, because it is fabricated in KTP, the waveguide component will withstand high optical power and have a significantly higher RF modulation figure of merit (FOM) relative to lithium niobate. KTP waveguides support high-power TE and TM modes - a necessary requirement for polarization-based modulation as with a Pockels cell. High-power fiber laser development has greatly outpaced fiber-based modulators in terms of its maturity and specifications. The demand for high-performance nonlinear optical (NLO) devices in terms of power handling, efficiency, bandwidth, and useful wavelength range has driven the development of bulk NLO options, which are limited in their bandwidth, as well as waveguide based LN modulators, which are limited by their low optical damage threshold. Today, commercially available lithium niobate (LN) modulators are used for laser formatting; however, because of photorefractive damage that can reduce transmission and increase requirements on bias control, LN modulators cannot be used with powers over several mW, dependent on wavelength. The high-power, high-speed modulators proposed for development under this effort will enable advancements in several exciting fields including lidarbased remote sensing, atomic interferometry, free-space laser communications, and others.
Hawthorne, Justin↗
TESS Observations of the WASP-121 b Phase Curve
We study the red-optical photometry of the ultrahot Jupiter WASP-121 b as observed by the Transiting Exoplanet Survey Satellite (TESS) and model its atmosphere through a radiative transfer simulation. Given its short orbital period of ∼1.275 days, inflated state, and bright host star, WASP-121 b is exceptionally favorable for detailed atmospheric characterization. Toward this purpose, we use allesfitter to characterize its full red-optical phase curve, including the planetary phase modulation and secondary eclipse. We measure the day- and nightside brightness temperatures in the TESS passband as 3012{sub −42}{sup +40} and 2022{sub −602}{sup +254} K, respectively, and do not find a statistically significant phase shift between the brightest and substellar points. This is consistent with inefficient heat recirculation on the planet. We then perform an atmospheric retrieval analysis to infer the dayside atmospheric properties of WASP-121 b, such as its bulk composition, albedo, and heat recirculation. We confirm the temperature inversion in the atmosphere and suggest H{sup −}, TiO, and VO as potential causes of the inversion, absorbing heat at optical wavelengths at low pressures. Future Hubble Space Telescope and James Webb Space Telescope observations of WASP-121 b will benefit from its first full phase curve measured by TESS.
46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
Optical encoder devices and systems
Devices, systems and methods for encoding information using optical components are described. Information associated with a first optical signal (e.g., an optical pump) is encoded onto the phase of a second optical signal (e.g., an optical probe) using cross phase modulation (XPM) in a non-linear optical medium. The optical signals are multiplexed together into the nonlinear optical medium. The probe experiences a modified index of refraction as it propagates through the medium and thus accumulates a phase change proportional to the intensity of the pump. The disclosed devices can be incorporated into larger components and systems for various applications such as scientific diagnostics, radar, remote sensing, wireless communications, and quantum computing that can benefit from encoding and generation of low noise, high resolution signals. Examples of the encoded information includes intrinsic noise from the optical source, or others signals of interest, such as electrical, optical, X-ray, or high-energy particle signals.
Buckley, Brandon Walter↗
Optical encoder devices and systems
Devices, systems and methods for encoding information using optical components are described. Information associated with a first optical signal (e.g., an optical pump) is encoded onto the phase of a second optical signal (e.g., an optical probe) using cross phase modulation (XPM) in a non-linear optical medium. The optical signals are multiplexed together into the nonlinear optical medium. The probe experiences a modified index of refraction as it propagates through the medium and thus accumulates a phase change proportional to the intensity of the pump. The disclosed devices can be incorporated into larger components and systems for various applications such as scientific diagnostics, radar, remote sensing, wireless communications, and quantum computing that can benefit from encoding and generation of low noise, high resolution signals. Examples of the encoded information includes intrinsic noise from the optical source, or others signals of interest, such as electrical, optical, X-ray, or high-energy particle signals.
Buckley, Brandon Walter↗
Phase-Controlled Polarization Modulators
We report technology development of millimeter/submillimeter polarization modulators that operate by introducing a a variable, controlled phase delay between two orthogonal polarization states. The variable-delay polarization modulator (VPM) operates via the introduction of a variable phase delay between two linear orthogonal polarization states, resulting in a variable mapping of a single linear polarization into a combination of that Stokes parameter and circular (Stokes V) polarization. Characterization of a prototype VPM is presented at 350 and 3000 microns. We also describe a modulator in which a variable phase delay is introduced between right- and left- circular polarization states. In this architecture, linear polarization is fully modulated. Each of these devices consists of a polarization diplexer parallel to and in front of a movable mirror. Modulation involves sub-wavelength translations of the mirror that change the magnitude of the phase delay.
Chuss, D. T.↗
Modular, Reconfigurable, High-Energy Technology Development
The Modular, Reconfigurable High-Energy (MRHE) Technology Demonstrator project was to have been a series of ground-based demonstrations to mature critical technologies needed for in-space assembly of a highpower high-voltage modular spacecraft in low Earth orbit, enabling the development of future modular solar-powered exploration cargo-transport vehicles and infrastructure. MRHE was a project in the High Energy Space Systems (HESS) Program, within NASA's Exploration Systems Research and Technology (ESR&T) Program. NASA participants included Marshall Space Flight Center (MSFC), the Jet Propulsion Laboratory (JPL), and Glenn Research Center (GRC). Contractor participants were the Boeing Phantom Works in Huntsville, AL, Lockheed Martin Advanced Technology Center in Palo Alto, CA, ENTECH, Inc. in Keller, TX, and the University of AL Huntsville (UAH). MRHE's technical objectives were to mature: (a) lightweight, efficient, high-voltage, radiation-resistant solar power generation (SPG) technologies; (b) innovative, lightweight, efficient thermal management systems; (c) efficient, 100kW-class, high-voltage power delivery systems from an SPG to an electric thruster system; (d) autonomous rendezvous and docking technology for in-space assembly of modular, reconfigurable spacecraft; (e) robotic assembly of modular space systems; and (f) modular, reconfigurable distributed avionics technologies. Maturation of these technologies was to be implemented through a series of increasingly-inclusive laboratory demonstrations that would have integrated and demonstrated two systems-of-systems: (a) the autonomous rendezvous and docking of modular spacecraft with deployable structures, robotic assembly, reconfiguration both during assembly and (b) the development and integration of an advanced thermal heat pipe and a high-voltage power delivery system with a representative lightweight high-voltage SPG array. In addition, an integrated simulation testbed would have been developed containing software models representing the technologies being matured in the laboratory demos. The testbed would have also included models for non-MRHE developed subsystems such as electric propulsion, so that end-to-end performance could have been assessed. This paper presents an overview of the MRHE Phase I activities at MSFC and its contractor partners. One of the major Phase I accomplishments is the assembly demonstration in the Lockheed Martin Advanced Technology Center (LMATC) Robot-Satellite facility, in which three robot-satellites successfully demonstrated rendezvous & docking, self-assembly, reconfiguration, adaptable GN&C, deployment, and interfaces between modules. Phase I technology maturation results from ENTECH include material recommendations for radiation hardened Stretched Lens Array (SLA) concentrator lenses, and a design concept and test results for a hi-voltage PV receiver. UAH's accomplishments include Supertube heatpipe test results, which support estimates of thermal conductivities at 30,000 times that of an equivalent silver rod. MSFC performed systems trades and developed a preliminary concept design for a 100kW-class modular reconfigurable solar electric propulsion transport vehicle, and Boeing Phantom Works in Huntsville performed assembly and rendezvous and docking trades. A concept animation video was produced by SAIC, wllich showed rendezvous and docking and SLA-square-rigger deployment in LEO.
Carrington, Connie↗
Multichannel telemetry system
A two-channel telemetry system is described in which one channel is used for high-rate data and the other channel for low-rate data communication. In the transmitter a signal, which subsequently phase modulates a carrier, is produced which is a function of at least the high-rate data, the low-rate data and the frequency of the subcarrier of the low-rate channel. In the receiver which includes a phase-locked loop, the high-rate data is detected off the receiver inphase channel output and the low-rate off the quadrature channel output.
Butman, S.↗
A Long-Range Precision Ranging System
A technique is presented that may be used for precision real-time continuous range measuring at long ranges. The technique uses a carrier that is phase modulated by a pseudo-random binary sequence. The characteristics of the sequence that make it acquirable are discussed. The general form of a receiver capable of tracking the carrier is given and is shown to be a kind of phase-locked loop. A two-loop system capable of tracking a pseudo-random sequence and its clock is given. The combination of the receiver and the sequence tracking system form a ranging receiver. The power division necessary between the carrier and the sidebands is shown to be determined by the noise bandwidths of the two tracking systems. The bandwidths necessary for tracking space probes and Earth satellites are given and some experiments in radar-tracking Earth satellites are described. Based on these experiments, estimates are made of the useful range of such a system in tracking space probes.
Easterling, Mahlon↗
Coherent communication link using diode-pumped lasers
Work toward developing a diffraction limited, single frequency, modulated transmitter suitable for coherent optical communication or direct detection communication is discussed. Diode pumped, monolithic Nd:YAG nonplanar ring oscillators were used as the carrier beam. An external modulation technique which can handle high optical powers, has moderate modulation voltage, and which can reach modulation rates of 1 GHz was invented. Semiconductor laser pumped solid-state lasers which have high output power (0.5 Watt) and which oscillate at a single frequency, in a diffraction limited beam, at the wavelength of 1.06 microns were built. A technique for phase modulating the laser output by 180 degrees with a 40-volt peak to peak driving voltage is demonstrated. This technique can be adapted for amplitude modulation of 100 percent with the same voltage. This technique makes use of a resonant bulk modulator, so it does not have the power handling limitations of guided wave modulators.
Kane, Thomas J.↗
Impact of Halogen Groups on the Properties of PEA–Based 2D Pb–Sn Halide Perovskites
Tuning broad emission in 2D Pb–Sn halide perovskites (HPs) is essential for advancing optoelectronic applications, particularly for color-tunable and white-light-emitting devices. This broad emission is linked to structural factors, such as defects and phase segregation of the Pb component within the Pb–Sn system, which are strongly influenced by the molecular structure and chemical properties of spacer cations. Atomic tuning of the spacers via halogenation opens up a new way to fine-tune the molecular properties, enabling further augmentations of HP functionalities. Nevertheless, the distinct broad emission's sensitivity to spacer chemistry remains underexplored. Here, halogenation's influence is systematically investigated on 2D HP emission characteristics using a high-throughput workflow. These findings reveal that the F-containing phenethylammonium (4F-PEA) spacer narrows the broadband PL, whereas Cl broadens it. Through a correlative study, it is found that 4F-PEA reduces not only the local phase segregation but also the defect levels and microstrains in 2D HPs. This is likely attributed to the manifestation of less lattice distortion via stronger surface coordination of the dipole-augmented 4F-PEA. Furthermore, these results highlight halogenation as a key factor in modulating phase segregation and defect density in 2D Pb–Sn HPs, offering a promising pathway to tune the emission for enhanced optoelectronic performance.
2D Pb-Sn halide perovskites↗
Absolute Distance Measurement with the MSTAR Sensor
The MSTAR sensor (Modulation Sideband Technology for Absolute Ranging) is a new system for measuring absolute distance, capable of resolving the integer cycle ambiguity of standard interferometers, and making it possible to measure distance with sub-nanometer accuracy. The sensor uses a single laser in conjunction with fast phase modulators and low frequency detectors. We describe the design of the system - the principle of operation, the metrology source, beamlaunching optics, and signal processing - and show results for target distances up to 1 meter. We then demonstrate how the system can be scaled to kilometer-scale distances.
modulation sideband technology for absolute rangin↗
Silicon Micromachining in RF and Photonic Applications
Texas Instruments (TI) has developed membrane and micromirror devices since the late 1970s. An eggcrate space membrane was used as the spatial light modulator in the early years. Discrete micromirrors supported by cantilever beams created a new era for micromirror devices. Torsional micromirror and flexure-beam micromirror devices were promising for mass production because of their stable supports. TI's digital torsional micromirror device is an amplitude modulator (known as the digital micromirror device (DMD) and is in production development, discussed elsewhere. We also use a torsional device for a 4 x 4 fiber-optic crossbar switch in a 2 cm x 2 cm package. The flexure-beam micromirror device is an analog phase modulator and is considered more efficient than amplitude modulators for use in optical processing systems. TI also developed millimeter-sized membranes for integrated optical switches for telecommunication and network applications. Using a member in radio frequency (RF) switch applications is a rapidly growing area because of the micromechanical device performance in microsecond-switching characteristics. Our preliminary membrane RF switch test structure results indicate promising speed and RF switching performance. TI collaborated with MIT for modeling of metal-based micromachining.
Lin, Tsen-Hwang↗
Methods and algorithms for computer synthesis of holographic elements to obtain a complex impulse response of optical information processing systems based on modern spatial light modulators
The possibilities of designing optical devices for data processing and imaging based on the manipulation of coherent light beams by means of spatial light modulators (SLMs) are investigated. A review of commercially available SLMs is presented and the limitations of their complex modulation characteristics are analysed. The main problem of using present-day SLMs is the lack of the ability to modulate directly all states within a unit circle in the complex plane. In this regard, the characteristics of current methods for the synthesis of holographic elements are described that implement a given complex impulse response of the optical system and are optimal for using SLMs with purely amplitude, purely phase, and hybrid amplitude – phase modulation. (paper)
46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗