Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “phase engineering”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

MODELING AND OPTIMIZATION OF A PCM-BASED OCEAN THERMAL ENERGY HARVESTER FOR POWERING UNMANNED UNDERWATER VEHICLES

As oceans cover over 70% of the planet’s surface, they represent a large reservoir of resources that remained vastly untapped. Uncrewed Underwater Vehicles (UUVs) are becoming key technology for ocean exploration. Ocean thermal gradient is a permanent and reliable energy source that can be used to power UUVs using phase change material (PCM)-based thermal engines. However, the main drawback of this technology is its low conversion efficiency. When using PCM-based thermal engines to power UUVs, there are different energy conversion stages, thermal-hydraulic, hydraulic-kinetic, kinetic-electrical, dependent of a wide variety of parameters. Thus, optimization of the overall energy conversion is still a challenge for powering the increasing energy demanding UUVs for long missions. The goal of this study is to propose a PCM-based ocean thermal energy harvesting system for powering the Solo II float. Using the ocean thermal energy reduces the cost for battery replacement and expands the float’s mission time. For this purpose, we developed a multiphysics model for a system consisting of thermal material, hydraulic, and electrical systems. This system is designed to provide the electrical power needed for the instruments aboard the underwater vehicle. The models of the hydraulic and the electric systems are implemented in MATLAB-Simulink/Simscape environment. The final model developed can provide 13.66 kJ of electrical energy, which is more than 1.5 times the energy requirement per cycle for the SOLO II float.

Ouro-Koura, Habilou↗
DOE OSTI2023

Single-pixel reconstructive mid-infrared micro-spectrometer

Miniaturized spectrometers in the mid-infrared (MIR) are critical in developing next-generation portable electronics for advanced sensing and analysis. The bulky gratings or detector/filter arrays in conventional micro-spectrometers set a physical limitation to their miniaturization. In this work, we demonstrate a single-pixel MIR micro-spectrometer that reconstructs the sample transmission spectrum by a spectrally dispersed light source instead of spatially grated light beams. The spectrally tunable MIR light source is realized based on the thermal emissivity engineered via the metal-insulator phase transition of vanadium dioxide (VO 2 ). We validate the performance by showing that the transmission spectrum of a magnesium fluoride (MgF 2 ) sample can be computationally reconstructed from sensor responses at varied light source temperatures. With potentially minimum footprint due to the array-free design, our work opens the possibility where compact MIR spectrometers are integrated into portable electronic systems for versatile applications.

47 OTHER INSTRUMENTATION↗
DOE OSTI2020

Advancing Scientific Productivity through Better Scientific Software: Developer Productivity and Software Sustainability Report

The Exascale Computing Project (ECP) provides a unique opportunity to advance computational science and engineering (CSE) through an accelerated growth phase in extreme-scale computing. Central to the project is the development of next-generation applications and software technologies that can exploit emerging architectures for optimal performance and provide high-fidelity, multiphysics, multiscale capabilities. However, disruptive changes in computer architectures and the complexities of tackling new frontiers in extreme-scale modeling, simulation, and analysis present daunting challenges to the productivity of software developers and the sustainability of software artifacts. Members of the CSE community - especially at extreme scales but more broadly at all scales of computing - face an urgent need to improve developer productivity, positively impacting product quality, development time, and staffing resources, and software sustainability, reducing the cost of maintaining, sustaining, and evolving software capabilities.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2021

Direct Air Capture of CO2 (DAC) [Tech Snapshot]

Researchers at Los Alamos have extensive capabilities in design, testing and optimization of: (1) new capture materials based on membrane separation, amine and other solvent and sorbent separation, and porous materials; (2) biological capture methods, particularly algae and plants; (3) full-scale systems using science-based virtual learning; and (4) system performance under specific meteorological conditions, impacts of CO2 capture via atmospheric data and simulations, and availability of energy and storage capacity. The goal for Los Alamos is advancing our physical technologies and engineered systems approaches from the development phase to a minimal viable product in the energy sector for commercial purposes. Los Alamos is seeking strategic commercialization partners to work with us in advancing these capabilities and technologies for commercial viability.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2021

Development of a Modular, Crushed-Rock Thermal Energy Storage Pilot Design

The goal of this project, primarily funded by the U.S. Department of Energy, is to design a next-step pilot to advance near-term energy storage integrated with a fossil plant to provide a facility capable of being viable and effective in a market with growing penetration of variable renewable energy (VRE). Thermal energy storage (TES) represents an ideal technology for this purpose. The current effort will complete a feasibility study to prepare for the Phase II pre-front end engineering design (pre-FEED) for implementing a crushed-rock TES system integrated with a natural gas combined cycle (NGCC) plant. The crushed rock storage technology, which is being developed by Brenmiller Energy, is a modular TES system termed bGen™, which can accommodate both thermal and electrical inputs and output steam, hot water, or hot air. For this application, the estimated efficiency is 80% thermal to thermal. The TES technology is being designed to operate on a slipstream from NYPA’s Eugene W. Zeltmann Power Project (Zeltmann) natural gas combined cycle (NGCC) plant. The projected size of the system will be up to 4 MWe with at least 4 hours of storage duration, or 16 MWh-e total. Final sizing is being determined during the ongoing feasibility study. The next-step pilot being designed as part of the current project will represent a 5-fold increase in scale for this TES technology, and will be used to validate the technology’s ability to provide effective and economical energy storage. This pilot would represent the next-to-last demonstration scale before the technology could be commercial ready at GWh-e scales in the 2030 timeframe. This project is expected to design the critical next-step pilot, which will be undertaken in real-world operating conditions to better determine the crushed rock TES technology’s ability to be integrated with an NGCC plant and assess degradation over transient cycling at rates befitting various marketplaces. The crushed-rock TES pilot design is a technically feasible next step in the development of the technology and is built upon years of prior testing and demonstration. The proposed TES technology was developed by Brenmiller over the last 8 years and has been tested in 3 generations of demonstration units at various sites, globally. During this field testing, different characteristics and performance of the technology were validated, including the following key features: energy storage capacity, energy storage charge/discharge rate, energy storage loses, energy storage mechanical testing. This presentation will provide an update on the results of the conceptual design study for the modular crushed-rock TES system, integrated with a NGCC power plant.

03 NATURAL GAS↗
DOE OSTI2026

Automating Detection and Diagnosis of Faults, Failures, and Underperformance in PV Plants

The project developed hybrid physics-based and machine-learning methods for near-real-time detection of balance-of-system faults (e.g., string, combiner, and tracker outages) in utility-scale Photovoltaic plants, achieving over 50% true positive rates with under 10% false positives and significantly reducing engineering setup time. In the extended phase, the scope expanded to plant-level underperformance analysis and industry benchmarking through the SUPER.epri.com platform. SUPER standardizes data processing and performance metrics across more than 9 GWac and 120+ plants, enabling robust comparisons and insights into loss rates, inverter downtime, and capacity degradation.

14 SOLAR ENERGY↗
DOE OSTI2026

Mechanism-Resolved PFM of Ferroionic and Ferroelectric Responses in Thickness-Gradient Hf 0.5 Zr 0.5 O 2 Libraries

Resolving growth mechanisms and thickness evolution of functional properties is one of the key tasks in materials discovery and optimization involving thin-film materials, traditionally requiring significant experimental budgets. Here we introduce the combination of thickness-gradient libraries and automated scanning probe microscopy as a systematic pathway to elucidate growth modes and disentangle ferroelectric and electrochemical contributions in ferroelectric thin films. As a model system, we explore the Hf 0.5 Zr 0.5 O 2 (HZO) gradient thin films grown on La x Sr 1-x MnO 3 (LSMO) bottom electrode thin films. Automated piezoresponse force microscopy, spectroscopy, and lithography reveals that irreversible topographic deformation arises from electrochemical activity at the LSMO surface, whereas reversible phase inversion in HZO reflects ferroelectric switching. Automated topography height-map scans are used to further quantify nucleation density, particle-size evolution, and roughness correlations across the thickness-gradient, demonstrating that improved plume stabilization during growth suppresses interfacial reactions and promotes dense, fine-grained HZO conducive to ferroelectric phase formation. This combined materials-engineering and automated-SPM framework establishes a platform for high-throughput, mechanism-resolved characterization of ferroionic and ferroelectric responses in complex oxide films.

FOS: Physical sciences↗
DOE OSTI2025

Stress-dependent χ phase transformation in a Ni-based superalloy

The ongoing push to elevate operating temperatures in aerospace gas turbine engines – driven by goals of enhanced fuel efficiency and reduced CO 2 emissions – mandates advancements in the creep resistance of Ni- and Co-based superalloys, which are integral for critical engine components. This study elucidates the role of stress assisted localized phase transformations in the creep properties of these alloys. By leveraging chemo-mechanical coupling, self-healing γ′ precipitates are designed to immobilize planar defects, thereby increasing creep resistance. Employing advanced characterization techniques such as high-resolution Scanning Transmission Electron Microscopy (HR-STEM), in conjunction with atomistic simulations and thermodynamic calculations, novel deformation pathways facilitated by χ local phase transformation (LPT) strengthening have been uncovered; notably, the formation of χ nano-laths through microtwinning and superlattice intrinsic stacking fault (SISF) shearing. This study highlights critical insights into the compositional boundaries necessary for optimizing LPT strengthening while avoiding deleterious bulk formation of η/χ phases. These advancements will guide the design of new alloys maximizing high-temperature creep strength for advanced aerospace applications.

Egan, Ashton J. [Friedrich-Alexander University Er↗
DOE OSTI2024

On the importance of species immiscibility in mixing-layer dynamics at supercritical pressures

The mixing dynamics of injected propellants is a key factor in determining the ignition performance and combustion-instability response of rocket engines, internal combustion engines, and gas turbines. A key source of uncertainty in the prediction of phase-exchange dynamics is the immiscibility of the injected propellants at supercritical pressure conditions, which induces liquid/vapor phase separation and surface-tension dynamics. While experimental observations indicate the presence of liquid/vapor interfacial structures, this interfacial dynamics is typically neglected in numerical analyses. To address this issue, the objective of the present study is to systematically evaluate the importance of species immiscibility on the phase-exchange dynamics of cryogenic LOX/GH2 mixing layers at typical rocket engine injection conditions. This is accomplished by comparing simulations of (i) a recently developed interface-capturing Regularized-Interface Method (RIM) formulation, and (ii) the commonly employed Diffuse-Interface Method (DIM) formulation. Analysis shows that the interfacial dynamics significantly impact the atomization and mixing of the propellants in the near-injector region, which is not captured by the DIM formulation. The findings of this study extend to other immiscible injection systems, such as LOX/kerosene and hydrocarbon-fuel/air, thereby highlighting the importance of resolving species immiscibility in simulating high-pressure combustion engines.

diffused-interface method↗
DOE OSTI2022

Experimental Studies of Low-Load Limit in a Stoichiometric Micro-Pilot Diesel Natural Gas Engine

While operating at light loads, diesel pilot-ignited natural gas engines with lean premixed natural gas suffer from poor combustion efficiency and high methane emissions. This work investigates the limits of low-load operation for a micro-pilot diesel natural gas engine that uses a stoichiometric mixture to enable methane and nitrogen oxide emission control. By optimizing engine hardware, operating conditions, and injection strategies, this study focused on defining the lowest achievable load while maintaining a stoichiometric equivalence ratio and with acceptable combustion stability. A multi-cylinder diesel 6.7 L engine was converted to run natural gas premix with a maximum diesel micro-pilot contribution of 10%. With a base diesel compression ratio of 17.3:1, the intake manifold pressure limit was 80 kPa(absolute). At a reduced compression ratio of 15:1, this limit increased to 85 kPa, raising the minimum stable load. Retarding the combustion phasing, typically used in spark-ignition engines to achieve lower loads, was also tested but found to be limited by degraded diesel ignition at later timings. Reducing the pilot injection pressure improved combustion stability, as did increasing pilot quantity at the cost of lower substitution ratios. The lean operation further reduced load but increased NOx and hydrocarbon emissions. At loads below the practical dual-fuel limit, a transition to lean diesel operation will likely be required with corresponding implications for the aftertreatment system.

03 NATURAL GAS↗
DOE OSTI2023

Oxidized structure and Compositional properties of 1144 phase FBS by analytical electron microscopy

The 1144 phase (Ae1A1Fe4As4) shows a strong advantage of engineering fabrication among Fe Iron)-based superconductor (FBS) family due to the robustness of its superconducting properties with respect to chemical inhomogeneities, granted by its uniform crystalline-layered structure. This regularity is furthermore associated to crystalline defects capable of acting as efficient pinning centers, which high critical currents achieved at high fields for these superconductors. Like other FBS phases, its lossless current-carrying capability can be remarkably degraded by distractions at grain boundaries (GBs). GB oxidation is an issue of upmost importance to the realization of the practical FBS application for high field (> 20T) magnet. In this study, we explore oxidized grain boundary and intrinsic grain structural properties of 1144 polycrystalline samples by applying analytical electron microscopy such as atomic resolution scanning transmission electron microscopy and atom probe tomography. These structural properties of samples produced by a mechanochemically assisted synthesis are evaluated following the degradation of superconducting properties due to oxidation. We observe a strong correlation between the contamination at grain boundaries and the decrease of transport properties of the bulk sample, while the crystallin structure seems to be not affected by the oxidation.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2026

OES CO 2 Pipeline FEED Project Design Basis Memorandum

The OES CO₂ Pipeline project will move captured carbon dioxide from two ethanol facilities near Gibson City, Illinois, roughly 7.8 miles southeast to three injection wells outside Anchor, where it will be permanently stored underground. The system is designed to handle up to 4.5 million metric tonnes per year of dense-phase CO₂ at pressures up to 2,500 psig, using 16-inch mainline pipe and 10.750-inch laterals made from API 5L X-60 and X-65 steel. Wall thicknesses vary depending on location, with thinner pipe in open country, heavier wall at road crossings, and the heaviest where the pipe passes under highways or railroads via horizontal directional drill. The pipe gets a fusion-bonded epoxy coating, with an added abrasion-resistant layer wherever it's bored or drilled. Major water crossings will use HDD rather than open trenching. The pipeline will be cathodically protected, equipped with SCADA-compatible pressure and temperature instrumentation, and monitored for leaks using a computational pipeline monitoring system per API RP 1130. Hydrostatic testing will be performed at 1.25 times design pressure, and an ILI caliper run will follow to catch any construction defects. Several items, including fracture toughness requirements, specific NDE methods, and ILI tool selection, are left for the detailed design phase. The whole system falls under 49 CFR Part 195 and ASME B31.4, and Gulf Interstate Engineering prepared this document as the FEED-level design basis under the CarbonSAFE Phase III program.

09 BIOMASS FUELS↗
DOE OSTI2021

Size- and Phase-Controlled Nanometer-Thick ß-Ga2O3 Films with Green Photoluminescence for Optoelectronic Applications

Realization and optimization of the tunable/enhanced optical properties is critical to further advance the field of optoelectronics, photonics, and nano-electronics. In this context, here, we demonstrate green-emission characteristics with a ~30 fold enhancement in selectively engineered nanocrystalline Ga2O3 with a control over size, phase and interface nanostructure. Pulsed-laser-deposited ß-phase Ga2O3 films with an average crystallite size of ~9 nm along with a highly dense, close-compact nano-columnar structure with lowest possible defect density facilitates the thirty-fold enhancement in the photoluminescence (PL) intensity in green-region. Enhanced PL-emission in the optimized, engineered nano-architecture sheds light in designing Ga2O3-materials for promising future optoelectronic/photocatalytic applications.

Ga2O3, Nanocrystalline Films, Pulsed-Laser Deposit↗
DOE OSTI2020

Scaling of two-phase water-steam relative permeability and thermal fluxes in porous media

Two-phase water-steam flow conditions are frequently encountered in many engineering applications, including geothermal reservoirs. Although routine calculations are based on the multiphase Darcy’s law, the role of the topology of the flowing phases at the pore-scale is usually neglected in the estimation of relative permeabilities. Instead, the latter are frequently computed using empirical models like the Corey correlation. In this work, we first apply the model for relative permeabilities based on pore-scale flow regimes developed by Picchi and Battiato (2019), Relative permeability scaling from pore-scale flow regimes, Water Resour. Res. 55, 3215–3233, to scenarios typical of geothermal reservoirs and then extend it by deriving the scaling laws for the transmissibilities and the thermal properties as a function of temperature. First, we discuss the scaling behavior of normalized relative permeabilities in terms of viscosity ratio and capillary number of water-steam systems and, then, we provide a validation of the model against experimental data available in the literature. The model captures well the data trends collected in real 3D porous media. These results suggest that water-steam relative permeabilities follow the same scaling behavior of gas-liquid systems where the non-wetting phase is much less viscous than the wetting phase. Finally, we investigate the impact that relative permeabilities have on heat transfer rates at two-phase flow conditions and the scaling of mass and energy transmissibility and thermal properties of the mixture. An estimation of the exergy carried by the two-phase water-steam mixture is also included.

42 ENGINEERING↗
DOE OSTI2021

Gen 3 Particle Pilot Plant (G3P3) -- High-Temperature Particle System for Concentrating Solar Power (Phases 1 and 2)

The U.S. Department of Energy Solar Energy Technologies Office initiated the Generation 3 Concentrating Solar Power (CSP) program to achieve higher operating temperatures (>700 °C) to enable next-generation CSP high-temperature power cycles such as the supercritical CO 2 (sCO2) Brayton Cycle. Three teams were selected to pursue high-temperature gas, liquid, and solid pathways for the heat-transfer media. Phases 1 and 2, which lasted from 2018 – 2020, consisted of design, modeling, and testing activities to further de-risk each of the technologies and develop a design for construction, commissioning, and operation of a pilot-scale facility in Phase 3 (2021 – 2024). This report summarizes the activities in Phases 1 and 2 for the solid-particle pathway led by Sandia National Laboratories. In Phases 1 and 2, Sandia successfully de-risked key elements of the proposed Gen 3 Particle Pilot Plant (G3P3) by improving the design, operation, and performance of key particle component technologies including the receiver, storage bins, particle-to-sCO2 heat exchanger, particle lift, and data acquisition and controls. Modeling and testing of critical components have led to optimized designs that meet desired performance metrics. Detailed drawings, piping and instrumentation diagrams, and process flow diagrams were generated for the integrated system, and structural analyses of the assembled tower structure were performed to demonstrate compliance with relevant codes and standards. Instrumentation and control systems of key subsystems were also demonstrated. Together with Bridgers & Paxton, Bohannan Huston, and Sandia Facilities, we have completed a 100% G3P3 tower design package with stamped engineering drawings suitable for construction bid in Phase 3.

14 SOLAR ENERGY↗
DOE OSTI2021

Incentivizing Adoption of Software Quality Practices

Although many software teams across the laboratories comply with yearly software quality engineering (SQE) assessments, the practice of introducing quality into each phase of the software lifecycle, or the team processes, may vary substantially. Even with the support of a quality engineer, many teams struggle to adapt and right-size software engineering best practices in quality to fit their context, and these activities aren’t framed in a way that motivates teams to take action. In short, software quality is often a “check the box for compliance” activity instead of a cultural practice that both values software quality and knows how to achieve it. In this report, we present the results of our 6600 VISTA Innovation Tournament project, "Incentivizing and Motivating High Confidence and Research Software Teams to Adopt the Practice of Quality." We present our findings and roadmap for future work based on 1) a rapid review of relevant literature, 2) lessons learned from an internal design thinking workshop, and 3) an external Collegeville 2021 workshop. These activities provided an opportunity for team ideation and community engagement/feedback. Based on our findings, we believe a coordinated effort (e.g. strategic communication campaign) aimed at diffusing the innovation of the practice of quality across Sandia National Laboratories could over time effect meaningful organizational change. As such, our roadmap addresses strategies for motivating and incentivizing individuals ranging from early career to seasoned software developers/scientists.

96 KNOWLEDGE MANAGEMENT AND PRESERVATION↗
DOE OSTI2021

Edge localized mode characteristics and divertor heat flux during stationary and transient phase for CFETR hybrid scenario

The study of edge localized mode (ELM) behavior, stationary heat flux and transient heat flux during the ELM crash phase is performed for a China Fusion Engineering Test Reactor (CFETR) 1 GW hybrid mode operation scenario ($R$ = 7.2 m, ${B_{\text{T}}}$ = 6.5 T, ${I_{\text{p}}}$ = 13.78 MA). Modeling and simulation start with a scenario obtained by multi-code integrated modeling on the one modeling framework for integrated tasks framework. Linear stability and nonlinear simulations of ELM dynamics are carried out using the BOUT++ six-field reduced magnetohydrodynamic module, which show a much smaller ELM energy loss (Δ ELM ~ 0.13%) compared to that of a Type-I ELM. Parametric analysis of the weak linear growth rate and small ELM energy loss characteristics shed light on physics corresponding to a grassy ELM regime for CFETR 1 GW hybrid scenario. The transient heat flux on the divertor target during this small ELM phase is investigated using BOUT++. Here we found that upstream radial transport in the scrape-off-layer (SOL) induced by small ELMs is weak, which keeps it in the drift-dominated region. However, the heat flux width is still broadened to ${\lambda _{\text{q}}}$ = 4.64 mm by the increase of separatrix temperature during ELM nonlinear evolution. The impact of transient peak heat load and ELM energy fluence on tungsten melting and net erosion rate of divertor target is evaluated for the first-time using physics-based transport that connects the pedestal with the SOL. Energy fluence caused by a single ELM pulse is below the tungsten melting limit, while tungsten erosion would exceed the material requirements. We conclude that external mitigation methods, such as divertor detachment and advanced divertor geometry are likely needed for the steady state operation of CFETR.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Multi-stage heat release of multi-component fuels: Insights and implications for advanced engine operation

Multi-stage heat release (MSHR) is a unique phenomenon typically seen in lean/diluted and low- to intermediate-temperature combustion. Despite its relevance to advanced engine operation, the MSHR of multi-component fuels has barely been quantified. This study aims to characterize the MSHR of multi-component fuels in a rapid compression machine (RCM) at conditions representative of advanced combustion engines. New experimental data are first reported in the RCM at an equivalence ratio of 0.4, pressure of 60 bar and temperatures from 702 to 795 K for a research grade, multi-component gasoline surrogate, termed PACE-20. Here, experiments confirm the existence of MSHR for PACE-20 at all temperatures, and reveal the strong inhibiting effect of temperature on MSHR, where increasing temperature inhibits MSHR by suppressing first stage heat release and promoting second and third stage heat release. A detailed chemical kinetic model is also adopted to model the experiments, with good agreement observed. The response of MSHR characteristics to changes in different engine operating parameters (i.e., temperature, pressure, equivalence ratio and CO 2 dilution level) and fuel compositions (i.e., mole fraction of n-pentane, n-heptane, isooctane, cyclopentane, 1-hexene, ethanol and aromatics in PACE-20) is further evaluated via statistical analysis coupling quasi-random sampling, extensive computer experiments and high-dimensional model representation. The change in MSHR is characterized through 8 quantities of interest (QOIs), i.e., duration and extent of each heat release stage, and their standard deviations. The analysis highlights the dependence of the QOIs on the individual parameters as well as their interplays, with temperature exhibiting the strongest impact among all parameters. Furthermore, it is demonstrated that if MSHR is to be facilitated and combustion phasing is to be extended to enable engine operation at higher compression ratios, it is recommended to operate the engine at low intake temperatures, boosted intake pressures and high CO 2 dilutions (i.e., high EGR levels) with gasoline fuels containing more n-pentane and less aromatics.

42 ENGINEERING↗