Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “passivating layer”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17

Silicon heterojunction solar cell with passivated hole selective MoO{sub x} contact

We explore substoichiometric molybdenum trioxide (MoO{sub x}, x < 3) as a dopant-free, hole-selective contact for silicon solar cells. Using an intrinsic hydrogenated amorphous silicon passivation layer between the oxide and the silicon absorber, we demonstrate a high open-circuit voltage of 711 mV and power conversion efficiency of 18.8%. Due to the wide band gap of MoO{sub x}, we observe a substantial gain in photocurrent of 1.9 mA/cm{sup 2} in the ultraviolet and visible part of the solar spectrum, when compared to a p-type amorphous silicon emitter of a traditional silicon heterojunction cell. Our results emphasize the strong potential for oxides as carrier selective heterojunction partners to inorganic semiconductors.

36 MATERIALS SCIENCE↗

Reduction of the interfacial trap density of indium-oxide thin film transistors by incorporation of hafnium and annealing process

The stable operation of transistors under a positive bias stress (PBS) is achieved using Hf incorporated into InO{sub x}-based thin films processed at relatively low temperatures (150 to 250 °C). The mobilities of the Hf-InO{sub x} thin-film transistors (TFTs) are higher than 8 cm{sup 2}/Vs. The TFTs not only have negligible degradation in the mobility and a small shift in the threshold voltage under PBS for 60 h, but they are also thermally stable at 85 °C in air, without the need for a passivation layer. The Hf-InO{sub x} TFT can be stable even annealed at 150 °C for positive bias temperature stability (PBTS). A higher stability is achieved by annealing the TFTs at 250 °C, originating from a reduction in the trap density at the Hf-InO{sub x}/gate insulator interface. The knowledge obtained here will aid in the realization of stable TFTs processed at low temperatures.

36 MATERIALS SCIENCE↗

Band offsets and electronic structures of interface between In{sub 0.5}Ga{sub 0.5}As and InP

III–V semiconductor interfacing with high-κ gate oxide is crucial for the high mobility metal-oxide-semiconductor field transistor device. With density functional theory calculations, we explored the band offsets and electronic structures of the In{sub 0.5}Ga{sub 0.5}As/InP interfaces with various interfacial bondings. Among six different bonding interfaces, we found that P-In(Ga) bonding interface showed the highest stability. Local density of states calculations was adopted to calculate the band offsets. Except for the metallic interface, we noticed that neither valence band offset nor conduction band offset depended on the interfacial bondings. For the most stable P-In(Ga) interface, we did not observe any gap states. Furthermore, we explored the P-In(Ga) interfaces with interfacial P-As exchange defects, which slightly modified the interface stability and the band offsets but did not produce any gap states. These findings provide solid evidence that InP could serve as a promising interfacial passivation layer between III–V material and high-κ oxide in the application of high mobility devices.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Oxygen vacancy-driven evolution of structural and electrical properties in SrFeO 3₋δ thin films and a method of stabilization

Epitaxial SrFeO 3-δ (SFO) thin films have been grown on various substrates by pulsed laser deposition. The structural and electrical properties of SFO thin films are monitored with time in different atmospheres at room temperature, showing time-dependent crystal structure and electrical conductivity. The increased out-of-plane lattice parameter and resistivity over time are associated with the increased oxygen vacancies density in SFO thin films. The epitaxial strain plays an important role in determining the initial resistivity, and the sample environment determines the trend of resistivity change over time. An amorphous Al 2 O 3 passivation layer has been found to be effective in stabilizing the structure and electrical properties of SFO thin films. Lastly, this work explores time dependent structure and properties variation in oxide films and provides a way to stabilize thin film materials that are sensitive to oxygen vacancies.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Bifurcation of self-folded polygonal bilayers

Motivated by the self-assembly of natural systems, researchers have investigated the stimulus-responsive curving of thin-shell structures, which is also known as self-folding. Self-folding strategies not only offer possibilities to realize complicated shapes but also promise actuation at small length scales. Biaxial mismatch strain driven self-folding bilayers demonstrate bifurcation of equilibrium shapes (from quasi-axisymmetric doubly curved to approximately singly curved) during their stimulus-responsive morphing behavior. Being a structurally instable, bifurcation could be used to tune the self-folding behavior, and hence, a detailed understanding of this phenomenon is appealing from both fundamental and practical perspectives. In this work, we investigated the bifurcation behavior of self-folding bilayer polygons. For the mechanistic understanding, we developed finite element models of planar bilayers (consisting of a stimulus-responsive and a passive layer of material) that transform into 3D curved configurations. Our experiments with cross-linked Polydimethylsiloxane samples that change shapes in organic solvents confirmed our model predictions. Finally, we explored a design scheme to generate gripper-like architectures by avoiding the bifurcation of stimulus-responsive bilayers. Our research contributes to the broad field of self-assembly as the findings could motivate functional devices across multiple disciplines such as robotics, artificial muscles, therapeutic cargos, and reconfigurable biomedical devices.

36 MATERIALS SCIENCE↗

A perspective on ordered vacancy compound and parent chalcopyrite thin film absorbers for photoelectrochemical water splitting

Chalcopyrites could fill the gap between the low-cost, poor-efficiency single junction metal oxide photoelectrochemical (PEC) water splitting cells and the high efficiency, yet costly III–V tandems. In this Perspective, we first review the key barriers that must be addressed by the community to enable economical chalcopyrite-based PEC water splitting. Then, we highlight how theoretical modeling can be used to identify promising ordered vacancy compound absorbers with improved energetics compared to their chalcopyrite parents. Finally, we describe how advanced spectroscopic analysis performed on chalcopyrite photocathodes after PEC testing uncovered a new passivation layer candidate for prolonged durability.

08 HYDROGEN↗

Black silicon solar thin-film microcells integrating top nanocone structures for broadband and omnidirectional light-trapping

Recently developed classes of monocrystalline silicon solar microcells (μ-cell) can be assembled into modules with characteristics (i.e., mechanically flexible forms, compact concentrator designs, and high-voltage outputs) that would be impossible to achieve using conventional, wafer-based approaches. In this paper, we describe a highly dense, uniform and non-periodic nanocone forest structure of black silicon (bSi) created on optically-thin (30 μm) μ-cells for broadband and omnidirectional light-trapping with a lithography-free and high-throughput plasma texturizing process. With optimized plasma etching conditions and a silicon nitride passivation layer, black silicon μ-cells, when embedded in a polymer waveguiding layer, display dramatic increases of as much as 65.7% in short circuit current, as compared to a bare silicon device. Here, the conversion efficiency increases from 8.1% to 11.5% with a small drop in open circuit voltage and fill factor.

79 ASTRONOMY AND ASTROPHYSICS↗

New structures of Fe3S for rare-earth-free permanent magnets

We applied adaptive genetic algorithm (AGA) to search for low-energy crystal structures of Fe 3 S. A number of structures with energies lower than that of the experimentally reported Pnma and I-4 structures have been obtained from our AGA searches. These low-energy structures can be classified as layer-motif and column-motif structures. In the column-motif structures, Fe atoms self-assemble into rods with bcc type of underlying lattice, which are separated by the holes terminated by S atoms. In the layer-motif structures, the bulk Fe is broken into slabs of several layers passivated by S atoms. Magnetic properties calculations showed that the column-motif structures exhibit reasonably high uniaxial magnetic anisotropy. In addition, we examined the effect of Co doping to Fe 3 S and found magnetic anisotropy can be enhanced through Co doping.

36 MATERIALS SCIENCE↗

Casimir forces in multilayer magnetodielectrics with both gain and loss

A path-integral approach to the quantization of the electromagnetic field in a linearly amplifying magnetodielectric medium is presented. Two continua of inverted harmonic oscillators are used to describe the polarizability and magnetizability of the amplifying medium. The causal susceptibilities of the amplifying medium, with negative imaginary parts in finite frequency intervals, are identified and their relationships to microscopic coupling functions are determined. By carefully relating the two-point functions of the field theory to the optical Green functions, we calculate the Casimir energy and Casimir forces for a multilayer magnetodielectric medium with both gain and loss. We point out the essential differences with a purely passive layered medium. For a single layer, we find different bounds on the Casimir force for fully amplifying and for lossy media. The force is attractive in both cases, even if the medium exhibits negative refraction. From our Lagrangian we also derive by canonical quantization the postulates of the phenomenological theory of amplifying magnetodielectrics.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Nonreciprocal Coulomb drag between quantum wires in the quasi-one-dimensional regime

Coulomb drag experiments have been an essential tool to study strongly interacting low-dimensional systems. Historically, this effect has been explained in terms of momentum transfer between electrons in the active and the passive layer. We report Coulomb drag measurements between laterally coupled GaAs/AlGaAs quantum wires in the multiple one-dimensional (1D) sub-band regime that break Onsager's reciprocity upon both layer and current direction reversal, in contrast to prior 1D Coulomb drag results. The drag signal shows nonlinear current-voltage (I-V) characteristics, which are well characterized by a third-order polynomial fit. These findings are qualitatively consistent with a rectified drag signal induced by charge fluctuations. However, the nonmonotonic temperature dependence of this drag signal suggests that strong electron-electron interactions, expected within the Tomonaga-Luttinger liquid framework, remain important and standard interaction models are insufficient to capture the qualitative nature of rectified 1D Coulomb drag.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

PV Degradation - Mounting & Temperature

Several studies have found indications that PV degradation may increase in hotter climates. We show in this paper that degradation does correlate to higher module temperatures, but that these temperatures are significantly affected by the module mounting and. The mechanisms of degradation vary with module technology and quality. Using data from different HIT module installations we were able to extract an activation energy that is consistent with hydrogen passivation layer degradation. In addition, we show that low degradation in hot climates can be achieved for Al-BSF technology if properly installed to reduce heat transfer in order to thermally decouple the modules from the roof. We also found that monofacial and bifacial PERC module degradation is in line with historical degradation rates of Al-BSF.

14 SOLAR ENERGY↗

Application of a Focused, Pulsed X-Ray Beam to the Investigation of Single-Event Transients in Al 0.3 Ga 0.7 N/GaN HEMTs

A focused, pulsed x-ray beam was used to compare SET characteristics in pristine and proton-irradiated Al 0.3 Ga 0.7 N/GaN HEMTs. Measured SET amplitudes and trailing-edge decay times were analyzed as was the collected charge, obtained by integrating the SET pulses over time. SETs generated in proton-irradiated HEMTs differed significantly from those in pristine HEMTs with regard to the decay times and collected charge. The decay times have previously been shown to be attributed to charge trapping by defect states that are caused either by imperfect material growth conditions or by protoninduced displacement damage. The longer decay times observed for proton-irradiated HEMTs are attributed to the presence of additional deep traps created when protons lose energy as they collide with the nuclei of constituent atoms. Comparison of electrical parameters measured before and immediately following exposure to the focused x-ray beam showed little change, confirming the absence of significant charge buildup in passivation layers by the x-rays themselves. In conclusion, a major advantage of the pulsed x-ray technique is that the region under the metal gate can be probed for single-event transients from the top side, an approach incompatible with pulsed-laser SEE testing that involves the use of visible light.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Velocity distribution function of sputtered gallium atoms during inductively coupled argon plasma treatment of a GaAs surface

A GaN laser diode at 403.3 nm is used to measure the velocity distribution function (vdf) of Ga atoms sputtered from a radio-frequency biased GaAs substrate in a low pressure inductively coupled plasma (ICP) argon discharge. To investigate both perpendicular (V{sub z} normal to wafer) and longitudinal (V{sub x} parallel to wafer) velocity components, laser induced fluorescence (LIF) measurements are performed in the z direction and atomic absorption spectroscopy (AAS) in the x direction. The longitudinal vdf of Ga sputtered atoms is very close to a Lorentzian function with V{sub x} comprised between 0 and 7500 m s{sup -1}, while the perpendicular velocities V{sub z} can reach 10 000 m s{sup -1}. Experimental results are compared to molecular dynamics (MD) simulations of Ar{sup +} ion sputtering of GaAs under 200 eV bombardment. MD predictions and experiments are in fairly good agreement, which confirms the existence of products sputtered from the surface with kinetic energies larger than 10 eV. In etching processes dominated by physical bombardment, these energetic atoms could alter passivation layers on sidewalls and be responsible for defects observed in nanodevices. The best fit of the Doppler-broadened LIF and AAS profiles with the vdfs predicted by sputtering theory allows one to estimate the surface binding energy of Ga atoms in GaAs, E{sub b}, to be around 3 eV.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Etching of Si 3 N 4 induced by electron beam plasma from hollow cathode plasma in a downstream reactive environment

An etching system based on the interaction of electrons extracted from a direct current (DC) hollow-cathode (HC) Ar plasma and injected towards a Si3N4 covered silicon substrate located in the downstream reactive environment created by an additional remote CF 4 /O 2 plasma source was developed and evaluated. By controlling the properties of the injected beam electrons, this approach allows to deliver energy to a surface functionalized by exposure to reactive species, and initiate surface etching. The energy of the primary beam electrons is controlled by the acceleration voltage relative to the HC discharge. Ar atoms flow from the high-pressure HC discharge into the low pressure downstream reactive environment in the process chamber. For an acceleration voltage greater than the ionization potential of Ar and/or process gas species, the energetic primary beam electrons produce a secondary plasma in the process chamber, and can also cause additional dissociation. We have characterized the properties of the secondary plasma and also surface etching of Si 3 N 4 as a function of process parameters, including acceleration voltage (0-80 V), discharge current of the HC discharge (1-2 A), pressure (3.5-20 mTorr), source to substrate distance (1.5 to 5 cm), and feed gas composition (20% and 80% O2 in CF 4 /O 2 ). The electron energy probability function (EEPF) measured with a Langmuir probe about 2.5 cm below the extraction ring suggests several major groups of electrons for this situation, including high energy primary beam electrons with an energy that varies as the acceleration voltage is changed and low energy electrons produced by beam electron-induced ionization of the Ar gas in the process chamber. When a remote CF 4 /O 2 plasma is additionally coupled to the process chamber, Si 3 N 4 surfaces can be functionalized, and by varying the energy of the beam electrons, Si 3 N 4 etching can be induced by electron-neutral synergy effect with plasma-surface interaction. For conditions without beam electron injection, the remote plasma etching rate (ER) of Si 3 N 4 depends strongly on the O 2 concentration in the CF 4 /O 2 processing gas mixture and can be suppressed for O 2 -rich process conditions by the formation of a SiONF passivation layer on the Si 3 N 4 surface. The combination of the HC electron beam source with the remote plasma source (HCEB-RP) makes it possible to induce Si 3 N 4 etching for O 2 -rich remote plasma conditions where remote plasma by itself produces negligible Si 3 N 4 etching. The electron enhanced etching of Si 3 N 4 depends strongly on O 2 /CF 4 mixing ratio reflecting changing arrival rates of O and F species at the surface. Optical emission spectroscopy was used to estimate the ratio of gas phase F and O densities and found to be controlled by the gas mixing ratio and independent of HC EB operating conditions. At this time the detailed sequence of events operative in the etching mechanism is unclear. While the increase of the electron energy is ultimately responsible for initiating surface etching, at present we cannot rule out a role of ions from the simultaneously produced secondary plasma in plasma surface interaction mechanisms.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Efficient, stable silicon tandem cells enabled by anion-engineered wide-bandgap perovskites

Maximizing the power conversion efficiency (PCE) of perovskite/silicon tandem solar cells that can exceed the Shockley-Queisser single-cell limit requires a high-performing, stable perovskite top cell with a wide bandgap. We developed a stable perovskite solar cell with a bandgap of ~1.7 electron volts that retained more than 80% of its initial PCE of 20.7% after 1000 hours of continuous illumination. Anion engineering of phenethylammonium-based two-dimensional (2D) additives was critical for controlling the structural and electrical properties of the 2D passivation layers based on a lead iodide framework. The high PCE of 26.7% of a monolithic two-terminal wide-bandgap perovskite/silicon tandem solar cell was made possible by the ideal combination of spectral responses of the top and bottom cells.

14 SOLAR ENERGY↗

Amidination of ligands for chemical and field-effect passivation stabilizes perovskite solar cells

Surface passivation has driven the rapid increase in the power conversion efficiency (PCE) of perovskite solar cells (PSCs). However, state-of-the-art surface passivation techniques rely on ammonium ligands that suffer deprotonation under light and thermal stress. We developed a library of amidinium ligands, of interest for their resonance effect–enhanced N–H bonds that may resist deprotonation, to increase the thermal stability of passivation layers on perovskite surfaces. This strategy resulted in a >10-fold reduction in the ligand deprotonation equilibrium constant and a twofold increase in the maintenance of photoluminescence quantum yield after aging at 85°C under illumination in air. Here, implementing this approach, we achieved a certified quasi–steady-state PCE of 26.3% for inverted PSCs; and we report retention of ≥90% PCE after 1100 hours of continuous 1-sun maximum power point operation at 85°C.

Yang, Yi↗

The BDX-MINI detector for Light Dark Matter search at JLab

This paper describes the design and performance of a compact detector, BDX-MINI, that incorporates all features of a concept that optimized the detection of light dark matter in the MeV-GeV mass range produced by electrons in a beam dump. It represents a reduced version of the future BDX experiment expected to run at JLAB. BDX-MINI was exposed to penetrating particles produced by a 2.176GeV electron beam incident on the beam dump of Hall A at Jefferson Lab. The detector consists of 30.5 kg of PbWO 4 crystals with sufficient material following the beam dump to eliminate all known particles except neutrinos. The crystals are read out using silicon photomultipliers. Completely surrounding the detector are a passive layer of tungsten and two active scintillator veto systems, which are also read out using silicon photomultipliers. The design was validated and the performance of the robust detector was shown to be stable during a six month period during which the detector was operated with minimal access.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Bond Synergy Model for Bond Energies in Alloy Oxides

In this work we introduce a metal-oxide bond-energy model for alloy oxides based on pure-phase bond energies and bond synergy factors that describe the effect of alloying on the bond energy between cations and oxygen, an important quantity to understand the formation of alloy oxides and their composition. This model is parameterized for binary cation-alloy oxides using density-functional theory energies and is shown to be directly transferable to multi-component alloy oxides. We parameterized the model for alloy oxide energies with metal cations that form the basis of corrosion resistant alloys, including Fe, Ni, Cr, Mo, Mn, W, Co, and Ru. We find that isoelectronic solutes allow quantification of pure-phase bond energies in oxides and the calculated bond energy values give sensible results compared to common experience, including the role of Cr as the passive-layer former in Fe–Ni–Cr alloys for corrosion applications. Additionally, the bond synergy factors give insights into the mutual strengthening and weakening effects of alloying on cation-oxygen bonds and can be related to enthalpy of mixing and charge neutrality constraints. We demonstrate how charge neutrality can be identified and achieved by the oxidation states that the different cations assume depending on alloy composition and the presence of defects.

Electrochemistry↗