Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “noise (Sound)”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
NASA NTRS2010

Broadband Fan Noise Prediction System for Turbofan Engines: BFaNS User's Manual and Developer's Guide - Volume 2

Pratt & Whitney has developed a Broadband Fan Noise Prediction System (BFaNS) for turbofan engines. This system computes the noise generated by turbulence impinging on the leading edges of the fan and fan exit guide vane, and noise generated by boundary-layer turbulence passing over the fan trailing edge. BFaNS has been validated on three fan rigs that were tested during the NASA Advanced Subsonic Technology Program (AST). The predicted noise spectra agreed well with measured data. The predicted effects of fan speed, vane count, and vane sweep also agreed well with measurements. The noise prediction system consists of two computer programs: Setup_BFaNS and BFaNS. Setup_BFaNS converts user-specified geometry and flow-field information into a BFaNS input file. From this input file, BFaNS computes the inlet and aft broadband sound power spectra generated by the fan and FEGV. The output file from BFaNS contains the inlet, aft and total sound power spectra from each noise source. This report is the second volume of a three-volume set documenting the Broadband Fan Noise Prediction System: Volume 1: Setup_BFaNS User s Manual and Developer s Guide; Volume 2: BFaNS User s Manual and Developer s Guide; and Volume 3: Validation and Test Cases. The present volume begins with an overview of the Broadband Fan Noise Prediction System, followed by step-by-step instructions for installing and running BFaNS. It concludes with technical documentation of the BFaNS computer program.

Morin, Bruce L.↗
NASA NTRS2010

Broadband Fan Noise Prediction System for Turbofan Engines: Validation and Test Cases - Volume 3

Pratt & Whitney has developed a Broadband Fan Noise Prediction System (BFaNS) for turbofan engines. This system computes the noise generated by turbulence impinging on the leading edges of the fan and fan exit guide vane, and noise generated by boundary-layer turbulence passing over the fan trailing edge. BFaNS has been validated on three fan rigs that were tested during the NASA Advanced Subsonic Technology Program (AST). The predicted noise spectra agreed well with measured data. The predicted effects of fan speed, vane count, and vane sweep also agreed well with measurements. The noise prediction system consists of two computer programs: Setup_BFaNS and BFaNS. Setup_BFaNS converts user-specified geometry and flow-field information into a BFaNS input file. From this input file, BFaNS computes the inlet and aft broadband sound power spectra generated by the fan and FEGV. The output file from BFaNS contains the inlet, aft and total sound power spectra from each noise source. This report is the third volume of a three-volume set documenting the Broadband Fan Noise Prediction System: Volume 1: Setup_BFaNS User s Manual and Developer s Guide; Volume 2: BFaNS User s Manual and Developer s Guide; and Volume 3: Validation and Test Cases. The present volume begins with an overview of the Broadband Fan Noise Prediction System, followed by validation studies that were done on three fan rigs. It concludes with recommended improvements and additional studies for BFaNS.

Morin, Bruce L.↗
NASA NTRSDate not supplied

Microstructure Controlled Multi-Layer Porous Material Liner Tested On The Advanced Noise Control Fan

A novel concept of multilayer micro structurally controlled noise mitigation porous material was developed and experimentally validated in the laboratory by normal incidence impedance test. Extensive parametric studies were made to understand various parameters that influence acoustic absorption and transmission loss based on the test specimen size, particle size, porosity, pore size, and its distribution through the thickness. The results were reported in many publications. This work was focused on applying the concept and assessing the validity of the technology to aircraft turbomachine engines. The NASA Glenn Research Center’s Advanced Noise Control Fan (ANCF) low-speed test rig was selected. The liner insert required a 4-ft internal diameter cylinder with a 2-inch thick and 9-inch axial length. The liner was fabricated in eight segments and assembled in an aluminum test rig. The liner was tested for both tonal and broadband noise at the Notre Dame Turbomachinery Lab White Field test facility, where the ANCF is located. The study concludes that: Microstructurally controlled porous material is very effective in dissipating the sound energy; the liner is effective for tonal noise (2 to 13 dB reduction in noise levels) that constitutes the major part of the overall fan noise, especially the blade passing frequency which is generally the dominating component; Also, the liner is effective for broadband noise with reductions in sound pressure level of about 3 dB for the shaft order greater than 20. The proposed two-layer liner model demonstrated the validity of the concept. More studies are required to optimize the design.

Liner↗
NASA NTRS1982

Supersonic jet noise generated by large scale instabilities

The role of large scale wavelike structures as the major mechanism for supersonic jet noise emission is examined. With the use of aerodynamic and acoustic data for low Reynolds number, supersonic jets at and below 70 thousand comparisons are made with flow fluctuation and acoustic measurements in high Reynolds number, supersonic jets. These comparisons show that a similar physical mechanism governs the generation of sound emitted in he principal noise direction. These experimental data are further compared with a linear instability theory whose prediction for the axial location of peak wave amplitude agrees satisfactorily with measured phased averaged flow fluctuation data in the low Reynolds number jets. The agreement between theory and experiment in the high Reynolds number flow differs as to the axial location for peak flow fluctuations and predicts an apparent origin for sound emission far upstream of the measured acoustic data.

Seiner, J. M.↗
NASA NTRSDate not supplied

Practical Conceptual Design of Quieter Urban VTOL Aircraft

A toolchain and process for conceptual design of VTOL rotorcraft, employing low- and mid-fidelity tools is presented. The approach is capable of providing more quantitatively-credible trades between noise, size, and cost metrics than the methods commonly used for conceptual design. In addition to a general conceptual design tool, the approach employs comprehensive analysis for trim, blade motion, and airloads; these are then used by acoustic analysis software to develop source sound, propagate it, and calculate noise metrics. A key aspect of the approach is flexibility to assess varied aircraft types and different technologies and design features. Vehicles are sized using a representative Urban Air Mobility design mission. Demonstration cases are presented for a single main rotor helicopter, quadrotor, side-by-side helicopter, and lift+cruise aircraft. Noise metrics used for demonstration are the FAA/EASA certification Effective Perceived Noise Levels for takeoff, flyover, and approach. The concept aircraft in this study are shown to achieve reductions in noise relative the initial design points, with changes in mission performance and cost as a consequence. Many of the designs are predicted to be tens of EPNdB quieter in the certification metrics than existing helicopters.

Conceptual Design↗
NASA NTRS1977

Noise reduction evaluation of grids in a supersonic air stream with application to Space Shuttle

Near field acoustic measurements were obtained for a model supersonic air jet perturbed by a screen. Noise reduction potential in the vicinity of the space shuttle vehicle during ground launch when the rocket exhaust flow is perturbed by a grid was determined. Both 10 and 12 mesh screens were utilized for this experiment, and each exhibited a noise reduction only at very low frequencies in the near field forward arc. A power spectrum analysis revealed that a modest reduction of from 3 to 5 decibels exists below a Strouhal number S sub t = 0.11. Above S sub t = 0.11 screen harmonics increased the observed sound pressure level. The favorable noise reductions obtained with screens for S sub t 0.11 may be of substantial interest for the space shuttle at ground launch.

Seiner, J. M.↗
NASA NTRS1994

Low-Noise Spiral Bevel Gears

Modified spiral bevel gears that generate relatively little noise and vibration designed and fabricated for use in U.S. Army OH-58D helicopter. Noise reduced by 12 to 19 dB. Similar low-noise, low-vibration spiral bevel gears used in other helicopters, with consequent benefits in comfort and health of pilots and passengers, enhancement of pilots' performance and safety through reduction of audible distraction, and reduction in cost and weight of helicopters through reduction in amount of sound-proofing material. Low-noise, low-vibration spiral bevel gears also used in drive axles of cars and trucks for smoother, quieter rides.

Lewicki, David G.↗
NASA NTRS1997

A Study of Fundamental Shock Noise Mechanisms

This paper investigates two mechanisms fundamental to sound generation in shocked flows: shock motion and shock deformation. Shock motion is modeled numerically by examining the interaction of a sound wave with a shock. This numerical approach is validated by comparison with results obtained by linear theory for a small-disturbance case. Analysis of the perturbation energy with Myers' energy corollary demonstrates that acoustic energy is generated by the interaction of acoustic disturbances with shocks. This analysis suggests that shock motion generates acoustic and entropy disturbance energy. Shock deformation is modeled numerically by examining the interaction of a vortex ring with a shock. These numerical simulations demonstrate the generation of both an acoustic wave and contact surfaces. The acoustic wave spreads cylindrically. The sound intensity is highly directional and the sound pressure increases with increasing shock strength. The numerically determined relationship between the sound pressure and the Mach number is found to be consistent with experimental observations of shock noise. This consistency implies that a dominant physical process in the generation of shock noise is modeled in this study.

Meadows, Kristine R.↗
NASA NTRS1992

Annoyance caused by aircraft en route noise

A laboratory experiment was conducted to quantify the annoyance response of people on the ground to enroute noise generated by aircraft at cruise conditions. The en route noises were ground level recordings of eight advanced turboprop aircraft flyovers and six conventional turbofan flyovers. The eight advanced turboprop enroute noises represented the NASA Propfan Test Assessment aircraft operating at different combinations of altitude, aircraft Mach number, and propeller tip speed. The conventional turbofan en route noises represented six different commercial airliners. The overall durations of the en route noises varied from approximately 40 to 160 sec. In the experiment, 32 subjects judged the annoyance of the en route noises as well as recordings of the takeoff and landing noises of each of 5 conventional turboprop and 5 conventional turbofan aircraft. Each of the noises was presented at three sound pressure levels to the subjects in an anechoic listening room. Analysis of the judgments found small differences in annoyance between three combinations of aircraft type and operation. Current tone and corrections did not significantly improve en route annoyance prediction. The optimum duration-correction magnitude for en route noise was approximately 1 dB per doubling of effective duration.

Mccurdy, David A.↗
NASA NTRS2004

Parametric Testing of Chevrons on Single Flow Hot Jets

A parametric family of chevron nozzles have been studied, looking for relationships between chevron geometric parameters, flow characteristics, and far-field noise. Both cold and hot conditions have been run at acoustic Mach number 0.9. Ten models have been tested, varying chevron count, penetration, length, and chevron symmetry. Four comparative studies were defined from these datasets which show: that chevron length is not a major impact on either flow or sound; that chevron penetration increases noise at high frequency and lowers it at low frequency, especially for low chevron counts; that chevron count is a strong player with good low frequency reductions being achieved with high chevron count without strong high frequency penalty; and that chevron asymmetry slightly reduces the impact of the chevron. Finally, it is shown that although the hot jets differ systematically from the cold one, the overall trends with chevron parameters is the same.

Bridges, James↗
NASA NTRS2003

Development of Novel Methods for the Reduction of Noise and Weight in Helicopter Transmissions

Over the 70-year evolution of the helicopter, man's understanding of vibration control has greatly increased. However, in spite of the increased performance, the extent of helicopter vibration problems has not significantly diminished. Crew vibration and noise remains important factors in the design of all current helicopters. With more complex and critical demands being placed on aircrews, it is essential that vibration and noise not impair their performance. A major source of helicopter cabin noise (which has been measured at a sound pressure level of over 100 dB) is the gearbox. Reduction of this noise has been a goal of NASA and the U.S. Army. Gear mesh noise is typically in the frequency range of 1000 to 3000 Hz, a range important for speech. A requirement for U.S. Army/NASA Advanced Rotorcraft Transmission project has been a 10-dB reduction compared to current designs. A combined analytical/experimental effort has been underway, since the end of the 80's, to study effects of design parameters on noise production. The noise generated by the gear mesh can be transmitted to the surrounding media through the bearings that support the gear shaft. Therefore, the use of fluid film bearings instead of rolling element bearings could reduce the transmission noise by 10 dB. In addition, the fluid film bearings that support the gear shaft can change the dynamics of the gear assembly by providing damping to the system and by being softer than rolling element bearings. Wave bearings can attenuate, and filter, the noise generated by a machine component due to the dynamic stiffness and damping coefficients. The attenuation ratio could be as large as 35-40 dB. The noise components at higher frequencies than a synchronous frequency can be almost eliminated.

Dimofte, Florin↗
NASA NTRS1999

F-16XL and F-18 High Speed Acoustic Flight Test Databases

This report presents the recorded acoustic data and the computed narrow-band and 1/3-octave band spectra produced by F-18 and F-16XL aircraft in subsonic flight over an acoustic array. Both broadband-shock noise and turbulent mixing noise are observed in the spectra. Radar and c-band tracking systems provided the aircraft position which enabled directivity and smear angles from the aircraft to each microphone to be computed. These angles are based on source emission time and thus give some idea about the directivity of the radiated sound field due to jet noise. A follow-on static test was also conducted where acoustic and engine data were obtained. The acoustic data described in the report has application to community noise analysis, noise source characterization and validation of prediction models. A detailed description of the signal processing procedures is provided. Follow-on static tests of each aircraft were also conducted for which engine data and far-field acoustic data are presented.

Kelly, J. J.↗
NASA NTRS1993

Signal processing of jet noise from flyover test data

Narrow-band spectra characterizing jet noise are constructed from flyover acoustic measurements. Radar and c-band tracking systems provided the aircraft position histories which enabled directivity and smear angles from the aircraft to each microphone to be computed. These angles are based on source emission time and thus give some idea about the directivity of the radiated sound field due to jet noise. Simulated spectra are included in the paper to demonstrate spectral broadening due to smear angle. The acoustic data described in the study has application to community noise analysis, noise source characterization and validation of prediction models. Both broadband-shock noise and turbulent mixing noise are observed in the spectra. A detailed description of the signal processing procedures is provided.

Kelly, Jeffrey J.↗
NASA NTRS1990

The radiation of sound from a propeller at angle of attack

The mechanism by which the noise generated at the blade passing frequency by a propeller is altered when the propeller axis is at an angle of attack to the freestream is examined. The measured noise field is distinctly non axially symmetric under such conditions with far field sound pressure levels both diminished and increased relative to the axially symmetric values produced with the propeller at zero angle of attack. Attempts have been made to explain this non axially symmetric sound field based on the unsteady (once per rev) loading experienced by the propeller blades when the propeller axis is at non zero angle of attack. A calculation based on this notion appears to greatly underestimate the measured azimuthal asymmetry of noise for high tip speed, highly loaded propellers. A new mechanism is proposed; namely, that at angle of attack, there is a non axially symmetric modulation of the radiative efficiency of the steady loading and thickness noise which is the primary cause of the non axially symmetric sound field at angle of attack for high tip speed, heavily loaded propellers with a large number of blades. A calculation of this effect to first order in the crossflow Mach number (component of freestream Mach number normal to the propeller axis) is carried out and shows much better agreement with measured noise data on the angle of attack effect.

Mani, Ramani↗
NASA NTRS1990

The radiation of sound from a propeller at angle of attack

The mechanism by which the noise generated at the blade passing frequency by a propeller is altered when the propeller axis is at an angle of attack to the freestream is examined. The measured noise field is distinctly non axially symmetric under such conditions with far field sound pressure levels both diminished and increased relative to the axially symmetric values produced with the propeller at zero angle of attack. Attempts have been made to explain this non axially symmetric sound field based on the unsteady (once per rev) loading experienced by the propeller blades when the propeller axis is at non zero angle of attack. A calculation based on this notion appears to greatly underestimate the measured azimuthal asymmetry of noise for high tip speed, highly loaded propellers. A new mechanism is proposed; namely, that at angle of attack, there is a non axially symmetric modulation of the radiative efficiency of the steady loading and thickness noise which is the primary cause of the non axially symmetric sound field at angle of attack for high tip speed, heavily loaded propellers with a large number of blades. A calculation of this effect to first order in the crossflow Mach number (component of freestream Mach number normal to the propeller axis) is carried out and shows much better agreement with measured noise data on the angle of attack effect.

Mani, R.↗
NASA NTRS2006

Measurement of Model Noise in a Hard-Wall Wind Tunnel

Identification, analysis, and control of fluid-mechanically-generated sound from models of aircraft and automobiles in special low-noise, semi-anechoic wind tunnels are an important research endeavor. Such studies can also be done in aerodynamic wind tunnels that have hard walls if phased microphone arrays are used to focus on the noise-source regions and reject unwanted reflections or background noise. Although it may be difficult to simulate the total flyover or drive-by noise in a closed wind tunnel, individual noise sources can be isolated and analyzed. An acoustic and aerodynamic study was made of a 7-percent-scale aircraft model in a NASA Ames 7-by-10-ft (about 2-by-3-m) wind tunnel for the purpose of identifying and attenuating airframe noise sources. Simulated landing, takeoff, and approach configurations were evaluated at Mach 0.26. Using a phased microphone array mounted in the ceiling over the inverted model, various noise sources in the high-lift system, landing gear, fins, and miscellaneous other components were located and compared for sound level and frequency at one flyover location. Numerous noise-alleviation devices and modifications of the model were evaluated. Simultaneously with acoustic measurements, aerodynamic forces were recorded to document aircraft conditions and any performance changes caused by geometric modifications. Most modern microphone-array systems function in the frequency domain in the sense that spectra of the microphone outputs are computed, then operations are performed on the matrices of microphone-signal cross-spectra. The entire acoustic field at one station in such a system is acquired quickly and interrogated during postprocessing. Beam-forming algorithms are employed to scan a plane near the model surface and locate noise sources while rejecting most background noise and spurious reflections. In the case of the system used in this study, previous studies in the wind tunnel have identified noise sources up to 19 dB below the normal background noise of the wind tunnel. Theoretical predictions of array performance are used to minimize the width and the side lobes of the beam pattern of the microphone array for a given test arrangement. To capture flyover noise of the inverted model, a 104-element microphone array in a 622-mm-diameter cluster was installed in a 19-mm-thick poly(methyl methacrylate) plate in the ceiling of the test section of the wind tunnel above the aircraft model (see Figure 1). The microphones were of the condenser type, and their diaphragms were mounted flush in the array plate, which was recessed 12.7 mm into the ceiling and covered by a porous aromatic polyamide cloth (not shown in the figure) to minimize boundary-layer noise. This design caused the level of flow noise to be much less than that of flush-mount designs. The drawback of this design was that the cloth attenuated sound somewhat and created acoustic resonances that could grow to several dB at a frequency of 10 kHz.

Soderman, Paul T.↗