Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “model structural error”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Probabalistic Risk Analysis and Thermal Margin Process for an Inflatable Aeroshell

Uncertainties always exist in atmospheric entry aeroheating environments and the thermal response of thermal protection system (TPS) material. These uncertainties are mitigated in the design by ap-plying margin and factors of safety to the TPS. Entry vehicle TPS is often conservatively over-sized for the heat loads that are experienced along the entry trajectory by stacking worst-case scenarios together. Additionally, the current TPS design and margin process used by NASA offers very little insight into the risk of over-temperature during flight and the reliability of the heat shield performance [1,3]. A probabilistic margin process can be used to calculate the amount of TPS margin necessary to survive a given entry heat load at a specified level of risk [2,3,4]. The vehicle’s initial entry state (entry velocity, flight path angle, and entry mass) determines the expected atmospheric entry environmental conditions and resulting heat load that the entry vehicle will experience. If there is flexibility in the entry state, then this process can be used to select an appropriate combination of entry state parameters and TPS size to target a desired reentry reliability. This probabilistic margin process allows engineers to make informed aeroshell design, entry-trajectory design, and TPS performance risk trades while preventing excessive TPS margin from being applied. The probabilistic TPS margin process has been performed to determine TPS thickness and entry heating constraints given an acceptable risk level for the Low Earth Orbit Flight Experiment of an Inflatable Decelerator (LOFTID) flight project. The process is used in a manner to size the entry heat load for a given flexible TPS (FTPS) thickness so that it meets project reliability standards while allowing the FTPS and the underlying inflatable structure (IS) to be pushed to adequately high temperatures. Since the LOFTID project is an experimental flight demonstration, it is de-sired to drive the FTPS and IS to temperatures that cover a large range of their thermal response models’ applicability. This will allow the thermal response models to be better improved and validated post-flight using LOFTID’s extensive instrumentation embedded within the aeroshell. The presentation demonstrates how uncertainty analysis is carried out using an end-to-end Monte Carlo process where three separate Monte Carlo simulations are run in sequence. The first Monte Carlo simulation operates on the entry trajectory model to generate trajectory parameter dispersions that are fed into the second Monte Carlo simulation. The second Monte Carlo simulation operates on the aerothermodynamics model to generate aeroheating parameter dispersions that are fed into the third Monte Carlo simulation. The third Monte Carlo simulation operates on the FTPS material thermal response model to generate the final FTPS/IS thermal response dispersions. The end-to-end Monte Carlo simulation propagates the uncertainties of each model into the next to quantify the resulting uncertainty of the FTPS/IS thermal response. The fractional contributions of the uncertain parameters in the trajectory, aerothermal, and thermal response models to the variance in the FTPS/IS thermal response is determined as a byproduct of the Monte Carlo analysis. The structural uncertainty of the FTPS thermal response model is evaluated by flight relevant ground testing and model error analysis using test measurements. This probabilistic TPS margin process had never been applied to an entry vehicle and it is one of the LOFTID project’s goals to demonstrate its merits.

Steven A. Tobin↗
NASA NTRS2020

An Observation‐Driven Approach to Improve Vegetation Phenology in a Global Land Surface Model

An empirical model calibration approach is presented that aims to approximate missing biosphere processes in a global land surface model without the need for substantial model structural changes. The strategy is implemented here using the NASA Catchment‐CN land surface model and Moderate Resolution Imaging Spectroradiometer (MODIS) observations of the fraction of absorbed photosynthetically active radiation (FPAR). Existing plant functional types (PFTs) of the Catchment‐CN model are divided into three subtypes, based on the bias between the model‐simulated and MODIS‐observed FPAR. Separate sets of vegetation parameters for each subtype are then calibrated at a small number of grid cells with homogeneous, single‐PFT land cover, using MODIS FPAR reference observations from 2003 to 2009. The effectiveness of the empirical approach at improving the realism of modeled vegetation dynamics is investigated with two global model simulations for the period 2010–2016, one using the newly calibrated parameter values and the other using the original values. Globally, the calibrated parameters reduce the root mean square error (RMSE) of the modeled FPAR with respect to MODIS by 0.029 (∼10%) on average. In some regions, substantially larger RMSE reductions are achieved. RMSE reductions are primarily driven by model bias reductions, with neutral effects on the temporal correlation skill. While the empirical approach is suitable for achieving consistent model improvements, it is shown to be sensitive to the characteristics of the model error, specifically a dominance of the bias component in the case of Catchment‐CN. Ultimately, more fundamental model structural changes may be required to achieve better improvements.

J. Kolassa↗
NASA NTRS1991

Simulator evaluation of system identification with on-line control law update for the controls and astrophysics experiment in space

A procedure for optimizing the performance of large flexible spacecraft that require active vibration suppression to achieve required performance is presented. The procedure is to conduct on-orbit testing and system identification followed by a control system design. It is applied via simulation to a spacecraft configuration currently being considered for flight test by NASA - the Controls, Astrophysics, and Structures Experiment in Space (CASES). The system simulator is based on a NASTRAN finite element structural model. A finite number of modes is used to represent the structural dynamics. The system simulator also includes models of the electronics, actuators, sensors, the digital controller, and the internal and external disturbances. Nonlinearities caused by quantization are included in the study to examine tolerance of the procedure to modelling errors. Disturbance and sensor noise is modelled as a Gaussian process. For system identification, the system is excited using sinusoidal inputs at the resonant frequencies of the structure using each actuator. Mode shapes, frequencies, and damping ratios are identified from the unforced response sensor data after each excitation. Then, the excitation data is used to identify the actuator influence coefficients. The results of the individual parameter identification analyses are assembled into an aggregate system model. The control design is accomplished based only on the identified model using multi-input/output linear quadratic Gaussian theory. Its performance is evaluated based on time-to-damp as compared with the uncontrolled structure.

Montgomery, Raymond C.↗
NASA NTRS1990

Intergration of system identification and robust controller designs for flexible structures in space

An approach is developed using experimental data to identify a reduced-order model and its model error for a robust controller design. There are three steps involved in the approach. First, an approximately balanced model is identified using the Eigensystem Realization Algorithm, which is an identification algorithm. Second, the model error is calculated and described in frequency domain in terms of the H(infinity) norm. Third, a pole placement technique in combination with a H(infinity) control method is applied to design a controller for the considered system. A set experimental data from an existing setup, namely the Mini-Mast system, is used to illustrate and verify the approach.

Juang, Jer-Nan↗
NASA NTRS1996

Multipath analysis diffraction calculations

This report describes extensions of the Kirchhoff diffraction equation to higher edge terms and discusses their suitability to model diffraction multipath effects of a small satellite structure. When receiving signals, at a satellite, from the Global Positioning System (GPS), reflected signals from the satellite structure result in multipath errors in the determination of the satellite position. Multipath error can be caused by diffraction of the reflected signals and a method of calculating this diffraction is required when using a facet model of the satellite. Several aspects of the Kirchhoff equation are discussed and numerical examples, in the near and far fields, are shown. The vector form of the extended Kirchhoff equation, by adding the Larmor-Tedone and Kottler edge terms, is given as a mathematical model in an appendix. The Kirchhoff equation was investigated as being easily implemented and of good accuracy in the basic form, especially in phase determination. The basic Kirchhoff can be extended for higher accuracy if desired. A brief discussion of the method of moments and the geometric theory of diffraction is included, but seems to offer no clear advantage in implementation over the Kirchhoff for facet models.

Statham, Richard B.↗
NASA NTRS1996

The Angular Power Spectrum of BATSE 3B Gamma-Ray Bursts

We compute the angular power spectrum C(sub l) from the BATSE 3B catalog of 1122 gamma-ray bursts and find no evidence for clustering on any scale. These constraints bridge the entire range from small scales (which probe source clustering and burst repetition) to the largest scales (which constrain possible anisotropics from the Galactic halo or from nearby cosmological large-scale structures). We develop an analysis technique that takes the angular position errors into account. For specific clustering or repetition models, strong upper limits can be obtained down to scales l approx. equal to 30, corresponding to a couple of degrees on the sky. The minimum-variance burst weighting that we employ is visualized graphically as an all-sky map in which each burst is smeared out by an amount corresponding to its position uncertainty. We also present separate bandpass-filtered sky maps for the quadrupole term and for the multipole ranges l = 3-10 and l = 11-30, so that the fluctuations on different angular scales can be inspected separately for visual features such as localized 'hot spots' or structures aligned with the Galactic plane. These filtered maps reveal no apparent deviations from isotropy.

Tegmark, Max↗
NASA NTRS2000

RFI and SCRIMP Model Development and Verification

Vacuum-Assisted Resin Transfer Molding (VARTM) processes are becoming promising technologies in the manufacturing of primary composite structures in the aircraft industry as well as infrastructure. A great deal of work still needs to be done on efforts to reduce the costly trial-and-error methods of VARTM processing that are currently in practice today. A computer simulation model of the VARTM process would provide a cost-effective tool in the manufacturing of composites utilizing this technique. Therefore, the objective of this research was to modify an existing three-dimensional, Resin Film Infusion (RFI)/Resin Transfer Molding (RTM) model to include VARTM simulation capabilities and to verify this model with the fabrication of aircraft structural composites. An additional objective was to use the VARTM model as a process analysis tool, where this tool would enable the user to configure the best process for manufacturing quality composites. Experimental verification of the model was performed by processing several flat composite panels. The parameters verified included flow front patterns and infiltration times. The flow front patterns were determined to be qualitatively accurate, while the simulated infiltration times over predicted experimental times by 8 to 10%. Capillary and gravitational forces were incorporated into the existing RFI/RTM model in order to simulate VARTM processing physics more accurately. The theoretical capillary pressure showed the capability to reduce the simulated infiltration times by as great as 6%. The gravity, on the other hand, was found to be negligible for all cases. Finally, the VARTM model was used as a process analysis tool. This enabled the user to determine such important process constraints as the location and type of injection ports and the permeability and location of the high-permeable media. A process for a three-stiffener composite panel was proposed. This configuration evolved from the variation of the process constraints in the modeling of several different composite panels. The configuration was proposed by considering such factors as: infiltration time, the number of vacuum ports, and possible areas of void entrapment.

Loos, Alfred C.↗
DOE OSTI2021

Transforming a Simple Structure Model to Represent a Complex Dynamic System with Unknown Boundary Restraints

Imposing a boundary condition on a structure can significantly alter its dynamic properties. However, sometimes the specifics of the new boundary conditions are not known. When the effects of a boundary condition are uncertain or there is not enough information, engineers need to excite the complex structure to obtain these modified properties. In order to experimentally obtain the new properties, engineers need multiple experiments and many outputs for interpolation in order to sufficiently represent the entire structure. In this study, the researchers attached a stinger to a cantilever beam, acting as a new transverse restraint of unknown properties. This paper presents a conversion expression that predicts the dynamic behavior of any point in the system with the new boundary condition. This expression relies only on one impact hammer experiment with one output and the model of the stinger-free cantilever beam, referred to as the simple structure. Researchers estimated the Transfer Function (TRF) of the beam and compared it with an experimentally measured TRF to validate the method. The mean absolute error of the estimated TRF compared to the experimental TRF is 1.99 dB. This demonstrates the use of the proposed method for estimating unmeasured TRFs in a system with an uncertain boundary condition using a single input, single output (SISO) test and a model of the simple structure.

42 ENGINEERING↗
NASA NTRS2014

The Uncertainty of Biomass Estimates from Modeled ICESat-2 Returns Across a Boreal Forest Gradient

The Forest Light (FLIGHT) radiative transfer model was used to examine the uncertainty of vegetation structure measurements from NASA's planned ICESat-2 photon counting light detection and ranging (LiDAR) instrument across a synthetic Larix forest gradient in the taiga-tundra ecotone. The simulations demonstrate how measurements from the planned spaceborne mission, which differ from those of previous LiDAR systems, may perform across a boreal forest to non-forest structure gradient in globally important ecological region of northern Siberia. We used a modified version of FLIGHT to simulate the acquisition parameters of ICESat-2. Modeled returns were analyzed from collections of sequential footprints along LiDAR tracks (link-scales) of lengths ranging from 20 m-90 m. These link-scales traversed synthetic forest stands that were initialized with parameters drawn from field surveys in Siberian Larix forests. LiDAR returns from vegetation were compiled for 100 simulated LiDAR collections for each 10 Mg · ha(exp -1) interval in the 0-100 Mg · ha(exp -1) above-ground biomass density (AGB) forest gradient. Canopy height metrics were computed and AGB was inferred from empirical models. The root mean square error (RMSE) and RMSE uncertainty associated with the distribution of inferred AGB within each AGB interval across the gradient was examined. Simulation results of the bright daylight and low vegetation reflectivity conditions for collecting photon counting LiDAR with no topographic relief show that 1-2 photons are returned for 79%-88% of LiDAR shots. Signal photons account for approximately 67% of all LiDAR returns, while approximately 50% of shots result in 1 signal photon returned. The proportion of these signal photon returns do not differ significantly (p greater than 0.05) for AGB intervals greater than 20 Mg · ha(exp -1). The 50m link-scale approximates the finest horizontal resolution (length) at which photon counting LiDAR collection provides strong model fits and minimizes forest structure uncertainty in the synthetic Larix stands. At this link-scale AGB greater than 20 Mg · ha(exp -1) has AGB error from 20-50% at the 95% confidence level. These results suggest that the theoretical sensitivity of ICESat-2 photon counting LiDAR measurements alone lack the ability to consistently discern differences in inferred AGB at 10 Mg · ha(exp -1) intervals in sparse forests characteristic of the taiga-tundra ecotone.

LiDAR↗
NASA NTRS1977

Severe weather prediction studies

A numerical forecast model is described which uses three-dimensional primitive equations to predict the evolution of the wind, temperature and moisture fields along with the subsynoptic-scale convective activity. There are 15 vertical levels set on a longitude-latitude horizontal grid. In this study, the horizontal grid distance is 70 km (0.625 deg latitude and 0.816 deg longitude at 40 deg N) and the time step is 90 sec. Orography is included and terrain coordinates are adopted. The forecast model is used to test two tornado-producing storms with very different synoptic structures. A 12 hr forecast is carried out for both cases. The rms errors of the forecast indicate much smaller errors in the middle troposphere than in the lower troposphere. The results demonstrate that a rather fine-mesh limited-area numerical model is capable of providing a valuable short-range forecast of the circulation and the mesoscale precipitation features.

Chang, C.-B.↗
NASA NTRS1990

Constructing second-order structural models with specified mass submatrix condition numbers

This paper presents a simple new algorithm for constructing second-order models for any given flexible structure, with these models satisfying the constraint that each leading principal submatrix of the mass matrix must have a specified condition number. Now, the effects of rounding errors in practical computation generally increase with increasing condition number, i.e. as the matrix considered approaches singularity. Thus, the new models should prove useful for the systematic testing of the numerical properties of many algorithms in the dynamics and control of flexible structures.

Williams, T.↗
DOE OSTI2025

Bayesian Inference for the Seismic Moment Tensor Using Regional Waveforms and Teleseismic- P Polarities with a Data-Derived Distribution of Velocity Models and Source Locations

The largest source of uncertainty in any source inversion is the velocity model used in the transfer function that relates observed ground motion to the seismic moment tensor. However, standard inverse procedure often does not quantify uncertainty in the seismic moment tensor due to error in the Green’s functions from uncertain event location and Earth structure. Here, we incorporate this uncertainty into an estimation of the seismic moment tensor using a data-derived distribution of velocity models based on complementary geophysical data sets, including thickness constraints, velocity profiles, gravity data, surface-wave group velocities, and regional body-wave travel times. The data-derived distribution of velocity models is then used as a prior distribution of Green’s functions for use in Bayesian inference of an unknown seismic moment tensor using regional and teleseismic-P waveforms. The use of multiple data sets is important for gaining resolution to different components of the moment tensor. The combined likelihood is estimated using data-specific error models and the posterior of the seismic moment tensor is estimated and interpreted in terms of the most probable source type.

58 GEOSCIENCES↗
DOE OSTI2025

Polarization options in inclusive DIS off tensor polarized deuteron

In the near future, the Jefferson Lab b 1 experiment will provide the second measurement of tensor polarized asymmetries in inclusive DIS on the deuteron. In this asymmetry, 4 independent tensor polarized structure functions contribute. This necessitates systematic approximations in the extraction of the leading twist structure function b 1 from a single tensor asymmetry measurement. Contamination from higher twist structure functions and kinematic effects is discussed here. Using a deuteron convolution model, we quantify the systematic errors from these approximations for two different choices for the target polarization direction (momentum transfer, electron beam direction). For Jefferson Lab 12 GeV kinematics, the systematic error turns out to be comparable between the two polarization options, while at higher Q 2 values the momentum transfer direction is preferred.

Cosyn, Wim [Florida International University, Miam↗
DOE OSTI2023

Polarimetric Geometric Modeling for mm-VLBI Observations of Black Holes

The Event Horizon Telescope (EHT) is a millimeter very long baseline interferometry (VLBI) array that has imaged the apparent shadows of the supermassive black holes M87* and Sagittarius A*. Polarimetric data from these observations contain a wealth of information on the black hole and accretion flow properties. In this work, we develop polarimetric geometric modeling methods for mm-VLBI data, focusing on approaches that fit data products with differing degrees of invariance to broad classes of calibration errors. We establish a fitting procedure using a polarimetric “m-ring” model to approximate the image structure near a black hole. By fitting this model to synthetic EHT data from general relativistic magnetohydrodynamic models, we show that the linear and circular polarization structure can be successfully approximated with relatively few model parameters. We then fit this model to EHT observations of M87* taken in 2017. In total intensity and linear polarization, the m-ring fits are consistent with previous results from imaging methods. In circular polarization, the m-ring fits indicate the presence of event-horizon-scale circular polarization structure, with a persistent dipolar asymmetry and orientation across several days. The same structure was recovered independently of observing band, used data products, and model assumptions. Despite this broad agreement, imaging methods do not produce similarly consistent results. Our circular polarization results, which imposed additional assumptions on the source structure, should thus be interpreted with some caution. Polarimetric geometric modeling provides a useful and powerful method to constrain the properties of horizon-scale polarized emission, particularly for sparse arrays like the EHT.

79 ASTRONOMY AND ASTROPHYSICS↗
NASA NTRS1986

Generalized parity relations for large space structures with uncertain parameters

The generalized parity relations method is a technique that can be used to detect sensor and actuator failures on a large space structure. A model of a grid structure was used to evaluate the performance of these relations. It shows their relative sensitivity to modeling errors. A method using sensor outputs and actuator inputs is required for the design of the generalized parity relations. Three different estimators are studied. The last estimator can generate relations optimized for the detection of a particular failure which are interesting when the level of sensor noise is high.

Dutilloy, J. R.↗
NASA NTRS1990

Aerodynamic parameters of High-Angle-of attack Research Vehicle (HARV) estimated from flight data

Aerodynamic parameters of the High-Angle-of-Attack Research Aircraft (HARV) were estimated from flight data at different values of the angle of attack between 10 degrees and 50 degrees. The main part of the data was obtained from small amplitude longitudinal and lateral maneuvers. A small number of large amplitude maneuvers was also used in the estimation. The measured data were first checked for their compatibility. It was found that the accuracy of air data was degraded by unexplained bias errors. Then, the data were analyzed by a stepwise regression method for obtaining a structure of aerodynamic model equations and least squares parameter estimates. Because of high data collinearity in several maneuvers, some of the longitudinal and all lateral maneuvers were reanalyzed by using two biased estimation techniques, the principal components regression and mixed estimation. The estimated parameters in the form of stability and control derivatives, and aerodynamic coefficients were plotted against the angle of attack and compared with the wind tunnel measurements. The influential parameters are, in general, estimated with acceptable accuracy and most of them are in agreement with wind tunnel results. The simulated responses of the aircraft showed good prediction capabilities of the resulting model.

Klein, Vladislav↗
DOE OSTI2019

Decorrelating the errors of the galaxy correlation function with compact transformation matrices

Abstract Covariance matrix estimation is a persistent challenge for cosmology, often requiring a large number of synthetic mock catalogues. The off-diagonal components of the covariance matrix also make it difficult to show representative error bars on the 2-point correlation function (2PCF) since errors computed from the diagonal values of the covariance matrix greatly underestimate the uncertainties. We develop a routine for decorrelating the projected and anisotropic 2PCF with simple and scale-compact transformations on the 2PCF. These transformation matrices are modelled after the Cholesky decomposition and the symmetric square root of the Fisher matrix. Using mock catalogues, we show that the transformed projected and anisotropic 2PCF recover the same structure as the original 2PCF while producing largely decorrelated error bars. Specifically, we propose simple Cholesky-based transformation matrices that suppress the off-diagonal covariances on the projected 2PCF by ${\sim } 95{{\ \rm per\ cent}}$ and that on the anisotropic 2PCF by ${\sim } 87{{\ \rm per\ cent}}$. These transformations also serve as highly regularized models of the Fisher matrix, compressing the degrees of freedom so that one can fit for the Fisher matrix with a much smaller number of mocks.

79 ASTRONOMY AND ASTROPHYSICS↗
NASA NTRS1983

Thermal analysis considerations for large space structures

A number of issues and needs relative to thermal analysis of large space structures and space stations are discussed. Some indications of trends in the Langley thermal-structural analysis research program consistent with the issues and needs are also presented. The main heat transfer mechanism in space is radiation; consequently, there is a need for a strong thrust on improved radiation analysis capability. Also the important interactions among temperatures, deformations, and controls need to be accounted for. Finite element analysis capability seems to be lagging behind lumped-parameter capability or heat pipe analysis. The Langley plan will include improving radiation analysis capability, evaluating the errors involved in certain approximate analysis and modeling techniques for large space trusses, and continuing the development of integrated thermal-structural finite elements with an emphasis on radiation heat transfer. Work will be initiated to develop finite element analysis techniques for heat pipes. Finally, optimization research activities will be oriented toward methods to design flexible orbiting structures to account for thermal and thermal deformation requirements.

Adelman, H. M.↗