Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “microstructure stability”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Graphite Material Behavior: NRC Graphite Behavior Model

Introduction to graphite Fabrication of graphite Unique features of nuclear grade graphite Providing the properties As-fabricated material properties of interest Thermal diff, thermal stability, mechanical strength, etc. General graphite behavior and degradation Microstructure: key to behavior Crystallographic structure Basal plane (covalent) bonding Porosity and pore microstructure Degradation Irradiation behavior Oxidation behavior Molten salt issues

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Thermal stability of additively manufactured austenitic 304L ODS alloy

Thermal stability and high-temperature mechanical properties of a 304L austenitic oxide dispersion strengthened (ODS) alloy manufactured via laser powder bed fusion (LPBF) are examined in this work. Additively manufactured 304L ODS alloy samples were aged at temperatures of 1000, 1100, and 1200 °C for 100 h in an argon atmosphere. Microstructure characterization of LPBF 304L ODS alloy before and after the thermal stability experiments revealed that despite the annihilation of dislocations, induced cellular substructure by the LPBF process was partially retained in the ODS alloy even after aging at 1200 °C. The size of Y-Si-O nanoparticles after aging at 1200 °C increased from 25 to 50 nm. EBSD analysis revealed that nanoparticles retained the microstructure of LPBF 304L ODS and hindered recrystallization and further grain growth. At 600 °C and 800 °C, the yield stress of the 290 and 145 MPa were measured, respectively, which are substantially higher than 113 MPa, and 68 MPa for 304L at the same temperatures. Furthermore, the creep properties of LPBF 304L ODS alloy were evaluated at a temperature of 700 °C under three applied stresses of 70, 85, and 100 MPa yielding a stress exponent (n) of ~7.7; the minimum creep rate at 100 MPa was found to be about two orders of magnitude lower than found in the literature for wrought 304L stainless steel.

36 MATERIALS SCIENCE↗
NASA NTRS1985

The role of microstructure and phase distribution in the failure mechanisms and life prediction model for PSZ coatings

Partially Stabilized Zirconia (PSZ) may become widely used for Thermal Barrier Coatings (TBC). Failure of these coatings can occur due to thermal fatigue in oxidizing atmospheres. The failure is due to the strains that develop due to thermal gradients, differences in thermal expansion coefficients, and oxidation of the bond coating. The role of microstructure and the cubic, tetragonal, and monoclinic phase distribution in the strain development and subsequent failure will be discussed. An X-ray diffraction technique for accurate determination of the fraction of each phase in PSZ will be applied to understanding the phase transformations and strain development. These results will be discussed in terms of developing a model for life prediction in PSZ coatings during thermal cycling.

Sisson, R. D., Jr.↗
DOE OSTI2022

The CALPHAD approach for HEAs: Challenges and opportunities

Phases are key microstructural features that determine material properties. The most intuitive way of representing phase stability in a material is by its phase diagram. The vastness of the composition space is the most compelling reason for investigating high-entropy alloys (HEAs), but it also creates major challenges in controlling phases and microstructures of HEAs due to lack of experimental phase diagrams in highly concentrated multicomponent space. The CALPHAD (Calculation of Phase Diagram) approach, although it needs improvements, is the only viable way to calculate multicomponent phase diagrams. The two major property databases in CALPHAD, Gibbs energy and mobility, when coupled, can provide not only the equilibrium phase information, but also information about diffusion and kinetics. In this article, we will review the use of the CALPHAD approach in understanding phase stability and diffusion in high-entropy alloys. Finally, we will discuss the notable trend of coupling the high-throughput CALPHAD approach with machine learning in HEA design.

36 MATERIALS SCIENCE↗
DOE OSTI2025

MX precipitate behavior in an irradiated advanced Fe-9Cr steel: Self-ion irradiation effects on phase stability

In an effort to optimize Fe-9Cr reduced activation ferritic/martensitic (RAFM) steels and to inform the design and operation of fusion reactors, this work represents the first in a series of cohesive studies dedicated to the evolution of MX-TiC precipitates under accelerated single and dual ion irradiations. This study investigates CNA9, a simplified Fe-9Cr RAFM steel featuring initial MX-TiC precipitate densities of (2.3±0.3)×10²¹ m⁻³. This material was subjected to single self-ion irradiation at damage levels ranging from 1 to 100 displacements per atom (dpa) over a temperature range of 300 to 600°C, with a nominal dose rate of 7×10⁻⁴ dpa/s. Irradiation-induced coarsening was observed, as evidenced by statistically significant increases in mean diameter sizes, at 15 dpa at both 500°C and 600°C, whereas no coarsening was noted at 300°C or 400°C. Further, complete dissolution of precipitates occurred at damage levels of 50 and 100 dpa across the two temperatures tested (300°C and 500°C) while no significant changes were observed at any doses below 15 dpa at 500°C. Experimentally parameterized recoil resolution modeling suggests that the observed radiation stability of MX-TiC precipitates is intricately linked to diffusional changes of solutes resulting from the co-evolution of microstructural features within the experiments. The findings align with current theoretical perspectives on radiation-induced precipitate stability in complex alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Microstructural Pattern Formation during Far-from-Equilibrium Alloy Solidification

We introduce a new phase-field formulation of rapid alloy solidification that quantitatively in- corporates non-equilibrium effects at the solid-liquid interface over a very wide range of interface velocities. Simulations identify a new dynamical instability of dendrite tip growth driven by solute trapping at velocities approaching the absolute stability limit. They also reproduce the formation of the widely observed banded microstructures, revealing how this instability triggers transitions between dendritic and microsegregation-free solidification. Predicted band spacings agree quantita- tively with observations in rapidly solidified Al-Cu thin films.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Thermal stability and coarsening of eutectic and near-eutectic Ni–Ce alloys

Ni–Ce alloys are currently being studied as a castable alternative to conventional Ni-based superalloys. To understand the evolution of microstructure and mechanical behavior at elevated temperatures, this study investigates the mechanism of coarsening behavior in eutectic and near eutectic Ni–Ce at 900 °C. The as-cast eutectic Ni–Ce consists of a combination of fine lamellar and rod eutectic colonies with coarser boundary regions. Upon annealing, continuous coarsening, via process of globularization, initiates at colony boundaries or primary dendrites where faults (termination and branches) in the lamellar structure are plentiful. Coarsening then proceeds by a combination of fault migration mechanism and lamellar boundary splitting, growing toward the center of the eutectic colonies with increasing annealing time. Coarsening near the center of a colony is extremely slow, indicating the eutectic microstructure itself is very stable. Here, the near-eutectic alloys containing primary dendrites coarsen and stabilize faster compared to the fully eutectic alloy. Moreover, an anomaly is observed in the hardness of the fully eutectic alloy after long exposure at elevated temperature compared to the near-eutectic alloys.

36 MATERIALS SCIENCE↗
NASA NTRSDate not supplied

Macro-scale Testing and Micromechanics Modeling of Fracture Behaviors for Boron Carbide Composites with Hierarchical Microstructures

With a unique combination of properties including high hardness, low density, wear and corrosion resistance, thermal stability, high neutron absorption, and semi-conductivity, boron carbide (B4C) is a candidate material for various engineering applications that involve extreme environment. The current applications of boron carbide, however, are limited by its intrinsic brittleness due to its strong covalent bonding. To toughen boron carbide, in this work hierarchical microstructure designs was used to provide multiple toughening mechanisms including crack deflection/bridging, micro-crack toughening, etc. Using field assisted sintering, B4C composites with hierarchical microstructure features including graphite platelets, micron and sub-micron sized TiB2 reinforcements were fabricated. The fracture toughness of fabricated B4C composites were previously measured at micro-scale using micro-indentation followed by post-testing microstructure inspection. However, questions including whether the fracture toughness enhancement measured at micro-scale can translate to macro-scale mechanical properties, and what are the fundamental mechanisms behind observed fracture toughness enhancement, remain to be answered. In this study, the fabricated B4C composites were tested using standardized four-point bending method to obtain fracture toughness at macro-scale. In addition, micromechanics modeling was conducted using MAC/GMC code and crack-band model to study the effect of residual stress and weak interphases on fracture behaviors of B4C composites reinforced with TiB2 particles. Through standardized four-point bending tests, fracture toughness enhancements up to 2.85, 3.32, and 3.65 MPa∙m(exp 1/2) (from 2.38 MPa∙m(exp 1/2)) were achieved for B4C composites with graphite platelets addition (micro/nano B4C), with TiB2 formation (micro B4C-TiB2), and with both graphite and TiB2 addition (micro/nano B4C-TiB2) respectively. Micromechanics modeling indicated that introduction of thermal residual stress and weak interphases caused enhanced micro-cracking behavior and resulted in the observed fracture toughness enhancement. These results furthered understanding about the mechanical behaviors at macro-scale and the mechanisms behind observed fracture toughness enhancement for B4C composites with hierarchical microstructures and can provide reference data for the future design of B4C composites with optimized microstructures for further fracture toughness enhancement.

Boron Carbide↗
DOE OSTI2023

The Effects of Silicon and Niobium Concentration on the Solidification Behavior and Microstructure of Cast Monel Alloys

Cast Monel alloys are used in applications requiring a combination of good mechanical properties and excellent resistance to corrosion. Despite prevalent industrial use, relatively few studies have been conducted to investigate the relationships between composition, solidification behavior, and microstructure. Given that these alloys are used in the cast and welded conditions, these factors have a significant influence over the material properties. Here, in this work, microstructural characterization, electron probe microanalysis, X-ray diffraction, and differential scanning calorimetry were used to study how changes in Si and Nb concentrations affected the solidification path and microstructure of Monel alloys. It was found that increasing Nb concentration stabilized higher amounts of MC carbides and suppressed graphite formation during solidification. It was also found that the high nominal concentration and segregation of Si to the liquid led to the formation of Ni 31 Si 12 and other silicides via terminal eutectic reactions at the end of solidification. A pseudo-binary solidification diagram was constructed using experimental data and was applied to predict the mass fraction of solidified eutectic as a function of composition. The modeled microstructures were found to be in good agreement with experimentally measured phase fractions.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Interface microstructure effects on dynamic failure behavior of layered Cu/Ta microstructures

Abstract Structural metallic materials with interfaces of immiscible materials provide opportunities to design and tailor the microstructures for desired mechanical behavior. Metallic microstructures with plasticity contributors of the FCC and BCC phases show significant promise for damage-tolerant applications due to their enhanced strengths and thermal stability. A fundamental understanding of the dynamic failure behavior is needed to design and tailor these microstructures with desired mechanical responses under extreme environments. This study uses molecular dynamics (MD) simulations to characterize plasticity contributors for various interface microstructures and the damage evolution behavior of FCC/BCC laminate microstructures. This study uses six model Cu/Ta interface systems with different orientation relationships that are as- created, and pre-deformed to understand the modifications in the plasticity contributions and the void nucleation/evolution behavior. The results suggest that pre-existing misfit dislocations and loading orientations (perpendicular to and parallel to the interface) affect the activation of primary and secondary slip systems. The dynamic strengths are observed to correlate with the energy of the interfaces, with the strengths being highest for low-energy interfaces and lowest for high-energy interfaces. However, the presence of pre-deformation of these interface microstructures affects not only the dynamic strength of the microstructures but also the correlation with interface energy.

42 ENGINEERING↗
NASA NTRS1987

Thermal stability of the nickel-base superalloy B-1900 + Hf with tantalum variations

The microstructure of the solutionized and aged nickel-base superalloy B-1900 + Hf was examined after additional aging at 982 C for 72, 250, and 1000 hours. Alloy compositions that were examined contained the normal 1.34 at. pct (4.3 wt pct) Ta as well as 0.67 at. pct and zero Ta levels. The gamma-prime phase agglomerated, became platelike in morphology, and decreased in volume fraction for all three alloys throughout the aging treatments. Changes which occurred in the gamma and gamma-prime phase compositions were nearly complete after 72 hours of aging while changes in the MC carbide composition continued throughout the aging. Blocky M6C carbides precipitated along the grain boundaries of all three alloys in the first 72 hours of aging. In addition, an acicular form of this Mo/Cr/Ni-rich carbide developed in the intragranular regions of the Ta-containing alloys.

Harmon, B. S.↗
DOE OSTI2026

Thermal Stability and Ion Irradiation Response of Refined Grained V – 4Cr – 4Ti

Since the 1960’s, there has been interest in V-4Cr-4Ti and similar alloys as candidates for low activation structural materials for advanced nuclear reactors. V-4Cr-4Ti was produced using arc melting and subsequently subjected to large strain extrusion machining to produce a multimodal microstructure largely composed of nanocrystalline and ultrafine grain sizes. In-situ thermal stability of the multimodal V-4Cr-4Ti to 800 °C shows the formation of vanadium carbides with negligible grain growth. In-situ dual-beam 16 KeV He+ and 1 MeV Kr2+ ion irradiation performed at 700 °C to a final dose of ~5 displacements per atom show the formation of small He cavities well distributed throughout the system, with preferential clustering at grain boundaries. This work provides insight into how the increased fraction of grain boundaries affect the simultaneous dual beam ion irradiation response of multimodal V – 4 wt.% Cr – 4 wt.% Ti at elevated temperatures. Analysis of the cavities reveal an areal density of 0.024±0.007 cavities/nm2 and swelling of 0.236% after the dual-beam ion irradiation. Nanoindentation shows a ~50% increase in hardening after the ion irradiation at 700 °C.

TEM↗
DOE OSTI2023

Machine-to-machine variability of roughness and corrosion in additively manufactured 316L stainless steel

Numerous studies on the corrosion response of metal AM have been conducted. Nonetheless, the specimens being tested are commonly ground or polished to remove the outer as-built surface. If metal AM is truly going to be employed as a transformative technology that can produce complex shapes that do not require traditional machining, then the material needs to be evaluated in the as-built state. The reality is that AM alloys have shown significant inconsistencies regarding as-built surface texture, topology, and residual stress. One metric that has shown significant unpredictability in the literature is the susceptibility to localized corrosion of typically passive alloys, such as stainless steel (SS). There are a large number of studies that have attempted to understand the corrosion response of metal AM materials, but these studies are typically performed on materials that have been printed on a single machine and often mechanically polished to a smooth finish. This study compares the corrosion response of as-built AM, laser-beam powder bed fusion (LB-PBF), 316L SS parts that have been fabricated on five different machines. The majority of this work focused on understanding the susceptibility to localized corrosion of AM metals with respect to machine-dependent variables, namely surface roughness, and build angle. Surface roughness data was collected using scanning white light triangulation, laser scanning confocal microscopy, and coherence scanning interferometry. The results show that there is significant variability (p two-tail < 0.05) in the susceptibility to local corrosion initiation of LB-PBF 316L SS samples built on different machines. Surface oxides were probed with electron dispersive spectroscopy and revealed that variations in local corrosion susceptibility likely arise from differences in the stability of the passive film caused by chemical segregation, unique microstructure, and tortuous roughness features at the as-built surfaces. The variability of roughness and corrosion properties from test samples printed on different machines was corroborated by property measurements performed at five different testing sites, proving reproducibility of the data. Most importantly, this study shows that if the as-built surface layer is removed through grinding or electropolishing the machine-to-machine variation observed in the corrosion susceptibility is reduced.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Mass transport in a highly immiscible alloy on extended shear deformation

Forced mixing to a single phase or supersaturated solid solution (SSS) and its prerequisite microstructure evolution in immiscible systems has been a focus of research for both fundamental science and a variety of applications. Controlling the formation of SSS by shear deformation assisted processing could enable a material design beyond conventional equilibrium microstructure in immiscible systems. Here, a highly immiscible (mixing enthalpy of ~ 20 kJ·mol -1 ) Cu-50 at. % Cr binary alloy was employed to investigate the microstructure evolution and localized tendencies of SSS during severe shear deformation. The present results demonstrate distinctive microstructure refinement process in each phase and how they lead to localized SSS as a function of shear strain. Preferential dynamic recrystallization occurs in the softer Cu phase due to strain localization, leading to substantial grain refinement. The refinement of Cr phase in the top-most layer, however, is enabled by the progressive evolution of grain lamination, splitting, and fragmentation as a function of shear strain. The eventual SSS is found to be strongly dependent on the local environments that affect the dislocation activity, including the level of microstructure refinement, the interfacial orientation relationship, hardness difference, and supposed stability of oxidation. Ab initio simulations comfirm that it is more favorable to oxidize Cr than Cu at incoherent Cu/Cr interfaces which then limits the mass transport on an incoherent boundary. Our results shed light on the underpinning mechanism for non-equilibrium mass transport in immiscible systems upon severe deformation that can be applicable to a variety of processing techniques aimed at producing immiscible alloys with superior mechanical properties.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Perspectives on intrinsic toughening strategies and passivation of perovskite films with organic additives

We report on the inclusion of 5-aminovaleric acid (5-AVA)—a bulky, long-chained organic molecule—as an additive to enhance the mechanical integrity of hybrid perovskite films. We studied a range of organic cation additives and found that 5-AVA was the most effective at improving cohesion energy, a key metric of mechanical reliability. MAPbI 3 films reinforced with 5-AVA added in 5% concentration increased cohesion energy 12-fold from 0.53 J/m 2 to 6.04 J/m 2 , an effect which is attributed to increased plasticity and crack deflection around grain boundaries of the additive-containing perovskite. The addition of 5-AVA also improves V oc in perovskite solar cells and carrier lifetimes with a minimal decrease in PCE, attributed to passivation reducing defect and trap densities. A Tauc plot analysis of the bandgap shows that 5-AVA increases the band gap of the perovskite, correlating with reduced film stress compared to MAPbI 3 . Finally, the usage of 5-AVA improves the intrinsic thermomechanical reliability, but this improvement comes at the penalty of slightly reduced device efficiency due to reduced charge extraction from the presence of the bulky, insulating organic additive.

14 SOLAR ENERGY↗
DOE OSTI2026

Aluminum addition to AISI 52100 steel: Initial assessment on impact to mechanical properties and tribological performance and pathways for improvement

Here, in the transportation industry, reducing component weight is an effective strategy to improve fuel efficiency and lower emissions. Martensitic AISI 52100 steel is commonly used in drivetrain bearing components due to its high strength and excellent tribological performance. To achieve lightweighting without sacrificing mechanical properties and tribological behavior, this study explored the 52100 steel alloy modified by introducing nominally 5 wt% aluminum. The addition of aluminum led to an approximately 6% density reduction, however, it resulted in reduced hardness, strength and wear resistance, in part due to stabilization of a substantial amount of ferrite, as suggested by microstructural examination. Introducing 0.15 wt% additional carbon reduced the ferrite and demonstrated feasibility of mitigating the mechanical and tribological degradation caused by aluminum. This case study provides fundamental insights into the balance between lightweighting and mechanical/tribological performance for steel alloys, serving as a reference for further development of lightweight bearing steels.

Aluminum addition↗
DOE OSTI2020

Nanoscale Engineering of Polymorphism in Cu 2 Se-Based Composites

Crystal polymorphism selection during synthesis is extremely challenging. However, promoting the formation of a specific metastable polymorph enables modulation of the functional properties of phase-change materials through alteration of the relative abundance of various polymorphs. Here, we demonstrate the stabilization of the superionic β-Cu 2 Se phase under ambient conditions and the direct control over the relative ratio between the α-Cu 2 Se and β-Cu 2 Se polymorphs in (x)CuGaSe 2 /(1-x)Cu 2 Se composites using CuGaSe 2 nanoseeds. Here, we found that the small lattice mismatch between β-Cu 2 Se (cubic) and the ab plane of tetragonal CuGaSe 2 nanoseeds promotes the formation of low-energy coherent CuGaSe 2 /β-Cu 2 Se interfaces leading to preferential stabilization of β-Cu 2 Se. Astonishingly, the hierarchical microstructure of the resulting composites enables a remarkable decoupling of charge and heat transport, which is manifested by a breakdown of the Wiedemann-Franz law

36 MATERIALS SCIENCE↗
DOE OSTI2022

Heat-resistant aluminium alloys

Scandium added to Al–Cu–Mg–Ag alloys leads to an in situ phase transformation of coherent Cu-rich nanoprecipitates at elevated temperature, with Sc atoms diffusing and occupying their interstitial sites. Notably, the transformed nanoprecipitates have enhanced thermal stability while maintaining a large volume fraction and these two microstructural features enable high tensile strength of the Al alloy with creep resistance up to 400 °C.

36 MATERIALS SCIENCE↗