Results for “mechanical properties testing” — Page 17

NASA NTRSDate not supplied

Innovations in Continuous Ultrasonic Welding of Thermoplastic Composites and Evaluation for Space Applications

The goals of NASA’s Thermoplastic Development for Exploration Applications (TDEA) Project include and assessment of thermoplastic composite joints for space structures by developing and maturing design capabilities, analysis tools and techniques, and manufacturing processes for thermoplastic composites. Through this effort the TDEA project will expand NASA’s in-house thermoplastic composite manufacturing capabilities, develop an understanding of advanced thermoplastic joining techniques relevant to space environments, evaluate the feasibility of reconfigurable composite structures, and advance structural analysis capabilities, including failure prediction of thermoplastic composites including joints. This presentation will provide an overview of the materials and manufacturing effort within the TDEA project. Three semi-crystalline and one amorphous thermoplastic composite system were selected for initial screening and provided an opportunity to gain manufacturing experience across a range of processing temperatures, rheological behavior, and composite properties. Equivalency to the National Center for Advanced Materials Performance (NCAMP) test report for Toray’s TC1225 material was established to provide confidence in in-house manufacturing and material properties were generated through baseline mechanical tests for each material. Material characterization data was generated for a subset of materials to (1) provide data for analysis and model development and (2) generate thermal, rheological and conductivity data across relevant temperatures. A key objective of the TDEA project is evaluation of thermoplastic composite joining processes suitable for in-space operations. This presentation will outline the project’s progress in fusion bonding candidate materials by common welding techniques to assess the quality, reproducibility and strength of the bond, as well as identify limitations to in-space manufacturing. The feasibility of joint disassembly and reassembly will be discussed.

thermoplastic composite↗

NASA NTRSDate not supplied

Manufacture, Characterization, and Fusion Welding of Thermoplastic Composites for Space Applications

The goals of NASA’s Thermoplastic Development for Exploration Applications (TDEA) Project include an assessment of thermoplastic composite joints for space structures by developing and maturing design capabilities, analysis tools and techniques, and manufacturing processes for thermoplastic composites. Through this effort the TDEA project will expand NASA’s in-house thermoplastic composite manufacturing capabilities, develop an understanding of advanced thermoplastic joining techniques relevant to space environments, evaluate the feasibility of reconfigurable composite structures, and advance structural analysis capabilities. This presentation will provide an overview of the materials and manufacturing effort within the TDEA project. Three semi-crystalline and one amorphous thermoplastic composite materials were selected for initial screening and provided an opportunity to gain manufacturing experience across a range of processing temperatures, rheological behavior, and composite properties. Equivalency to the National Center for Advanced Materials Performance (NCAMP) test report for Toray’s TC1225 material was established to provide confidence in in-house manufacturing and material properties were generated through baseline mechanical tests for each material. Material characterization data was generated for a subset of materials to (1) provide data for analysis and model development and (2) generate thermal, rheological and conductivity data across relevant temperatures. A key objective of the TDEA project is evaluation of thermoplastic composite joining processes suitable for in-space operations. This presentation will outline the project’s progress in fusion bonding of candidate materials to assess the quality, reproducibility and strength of the bond, as well as identify limitations to in-space manufacturing. The feasibility of joint disassembly and reassembly will be discussed.

thermoplastic composite↗

NASA NTRSDate not supplied

Manufacture, Characterization, and Fusion Welding of Thermoplastic Composites for Space Applications

The goals of NASA’s Thermoplastic Development for Exploration Applications (TDEA) Project include and assessment of thermoplastic composite joints for space structures by developing and maturing design capabilities, analysis tools and techniques, and manufacturing processes for thermoplastic composites. Through this effort the TDEA project will expand NASA’s in-house thermoplastic composite manufacturing capabilities, develop an understanding of advanced thermoplastic joining techniques relevant to space environments, evaluate the feasibility of reconfigurable composite structures, and advance structural analysis capabilities, including failure prediction of thermoplastic composites including joints. This presentation will provide an overview of the materials and manufacturing effort within the TDEA project. Three semi-crystalline and one amorphous thermoplastic composite system were selected for initial screening and provided an opportunity to gain manufacturing experience across a range of processing temperatures, rheological behavior, and composite properties. Equivalency to the National Center for Advanced Materials Performance (NCAMP) test report for Toray’s TC1225 material was established to provide confidence in in-house manufacturing and material properties were generated through baseline mechanical tests for each material. Material characterization data was generated for a subset of materials to (1) provide data for analysis and model development and (2) generate thermal, rheological and conductivity data across relevant temperatures. A key objective of the TDEA project is evaluation of thermoplastic composite joining processes suitable for in-space operations. This presentation will outline the project’s progress in fusion bonding candidate materials by common welding techniques to assess the quality, reproducibility and strength of the bond, as well as identify limitations to in-space manufacturing. The feasibility of joint disassembly and reassembly will be discussed.

thermoplastic composite↗

NASA NTRS2001

Space Environmental Effects Testing and Characterization of the Candidate Solar Sail Material Aluminized Mylar

The usage of solar sails as a propellantless propulsion system has been proposed for many years. The technical challenges associated with solar sails are fabrication of ultralightweight films, deploying the sails and controlling the spacecraft. Integral to all these challenges is the mechanical property integrity of the sail while exposed to the harsh environment of space. This paper describes testing and characterization of a candidate solar sail material, Aluminized Mylar. This material was exposed to a simulated Geosynchronous Transfer Orbit (GTO) and evaluated by measuring thermooptical and mechanical property changes. Testing procedures and results are presented.

Edwards, D. L.↗

DOE OSTI2023

Small Scale Creep Testing of 14YWT via In-situ Transmission Electron Microscopy Irradiation and Nanoindentation

The next generation of nuclear materials must withstand harsh operating conditions such as high temperatures and irradiation doses. Nanostructured ferritic alloys like oxide dispersion strengthened steels, especially 14YWT, have shown promise as a structural material to withstand these harsh operating conditions. For application, understanding the irradiation enhanced creep of the structural components is fundamental to evaluating the service life in a reactor. Challenges with evaluating irradiation enhanced creep are related to the limited space in nuclear reactors and the expense of conducting post irradiation experiments on irradiated cladding. Ion irradiations are considered to expedite irradiation testing, but such experiments have restricted depth of penetration into the material, limiting the ability to characterize changes to material properties after irradiation. Small scale mechanical testing can be used with ion beam irradiations as a potential avenue to evaluate the irradiation enhanced creep of materials. In this study, in-situ transmission electron microscopy nanopillar creep studies on 14YWT were performed and simultaneously ion beam irradiated with 2.8 MeV Au4+ ions. It was observed that the ion beam irradiation did increase the measured strain rate of the materials. In addition, ex-situ nanoindentation creep studies were performed over a range of temperatures on control 14YWT, and it was observed that there was a change in the deformation mechanism between 873 K and 1073 K that agrees well with macro-scale mechanical testing. Furthermore, these results show promise for applying these techniques to nuclear materials in the future.

14 YWT↗

NASA NTRS2001

Thermal Characterization of Epoxy Adhesive by Hotfire Testing

This paper describes subscale solid-rocket motor hot-fire testing of epoxy adhesives in flame surface bondlines to evaluate heat-affected depth, char depth and ablation rate. Hot-fire testing is part of an adhesive down-selection program on the Space Shuttle Solid Rocket Motor Nozzle to provide additional confidence in the down-selected adhesives. The current nozzle structural adhesive bond system is being replaced due to obsolescence. Prior to hot-fire testing, adhesives were tested for chemical, physical and mechanical properties, which resulted in the selection of two potential replacement adhesives, Resin Technology Group's TIGA 321 and 3M's EC2615XLW. Hot-fire testing consisted of four forty-pound charge (FPC) motors fabricated in configurations that would allow side-by-side comparison testing of the candidate replacement adhesives with the current RSRM adhesives. Results of the FPC motor testing show that: 1) the phenolic char depths on radial bondlines is approximately the same and vary depending on the position in the blast tube regardless of which adhesive was used, 2) the replacement candidate adhesive char depths are equivalent to the char depths of the current adhesives, 3) the heat-affected depths of the candidate and current adhesives are equivalent, and 4) the ablation rates for both replacement adhesives were equivalent to the current adhesives.

Spomer, Ken A.↗

NASA NTRS2016

ASTM Committee C28: International Standards for Properties and Performance of Advanced Ceramics-Three Decades of High-Quality, Technically-Rigorous Normalization

Physical and mechanical properties and performance of advanced ceramics and glasses are difficult to measure correctly without the proper techniques. For over three decades, ASTM Committee C28 on Advanced Ceramics, has developed high-quality, technically-rigorous, full-consensus standards (e.g., test methods, practices, guides, terminology) to measure properties and performance of monolithic and composite ceramics that may be applied to glasses in some cases. These standards contain testing particulars for many mechanical, physical, thermal, properties and performance of these materials. As a result these standards are used to generate accurate, reliable, repeatable and complete data. Within Committee C28, users, producers, researchers, designers, academicians, etc. have written, continually updated, and validated through round-robin test programs, 50 standards since the Committee's founding in 1986. This paper provides a detailed retrospective of the 30 years of ASTM Committee C28 including a graphical pictogram listing of C28 standards along with examples of the tangible benefits of standards for advanced ceramics to demonstrate their practical applications.

properties↗

DOE OSTI2020

Boride-Carbon Hybrid Technology to Produce Ultra-Wear and Corrosion Resistant Surfaces for Applications in Harsh Conditions (Final Technical Report)

Engineered functional surfaces play an important role to enable new products and manufacturing processes that can endure harsh service conditions such as high impact and contact loads, highly abrasive wear, extreme temperatures, and corrosive environments. Engineered surfaces can also be instrumental to improving the efficient use of energy by reducing frictional losses and extending service life. The main objective of this project was to develop a hybrid surface engineering technology that combines the advantages of a novel ultrafast boriding process with the next generation of superhard carbon coatings. The hypothesis was that this hybrid process will offer an unprecedented combination of wear and corrosion resistance, low frictional losses and affordability for treated parts so that it can be utilized in many applications. During this project, a duplex process was developed that combines the advantages of ultra-fast electrochemical boriding with those of hard tetrahedral amorphous carbon coatings. Both technologies can be combined to form a hybrid technology that is characterized by low friction and wear properties combined with corrosion and fatigue resistance. Good adhesion of both layers to each other was one main goal of this project, that has been achieved with HF1 adhesion through the Rockwell-C adhesion test. In this project, the mechanical properties of the hybrid coating were modeled through a finite-element analysis approach. We can conclude that the FEA model resembles the actual samples and be utilized to predict mechanical behavior under impacts. Based on this model, application-oriented load conditions can be simulated for optimal layer design regarding thickness and mechanical properties. To exemplify, one conclusion that can be drawn from the nanoindentation model is a boride layer thickness of 50 µm is sufficient to effectively support the carbon coating on the identified AISI 1045 low carbon steel substrate material. The duplex treatment yields wear rates as low as 6 x 10 -8 mm 3 N -1 m -1 and a coefficient of friction of 0.14 when tested against a steel counter face in a ball-on-disk test setup. On the other hand, the wear rate of the only-borided AISI 1045 steel was 5 x 10 -5 mm 3 N -1 m -1 , about three orders of magnitude higher than the duplex coating. At the same time, duplex treated samples experience corrosion resistance, which could not be achieved with single-layer carbon coatings. The developed surface treatment withstands a 3-hour exposure to 15% HCl, while the only carbon coated counter sample shows severe delamination of the coating due to pin hole corrosion. The boride layer is chemically stable and pin hole free because it is formed through an electrochemical process under high current densities (700 mA/cm 2 ) and high temperature. Additionally, the hybrid coating led to at least 3x increase in fatigue strength of the steel substrate, which exceeds the target performance of 30% improvement. There are numerous potential applications for the duplex coatings. A representative application is bearing ball coatings for off-shore windmills. Compared to currently employed surface technologies in this field, the initial costs of applying our technology might be higher due to more process steps but the performance benefits lead to an increased life time of treated parts, which will lower the maintenance and replacement costs in the long-term. To validate the technology for this specific application, the team is currently investigating the process of white etching crack initiation of the duplex coating in collaboration with ANL. Overall, this project successfully validated that the boride-carbon hybrid technology can withstand harsh conditions. One possible approach to commercialization under consideration is to transfer the technology to a startup or an existing coatings company.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Mechanical Properties of Irradiated U-10 wt. %Mo Alloy Degraded by Porosity Development

In this study, a plate-type nuclear fuel consisting of a solid monolithic foil of U-10 wt. %Mo is under development for use in the United States' high-performance research reactors. In support of developing this fuel, the fuel has been fabricated for the first time by a commercial fuel vendor and subsequently irradiated in a test reactor. This provides an opportunity to evaluate postirradiation mechanical properties of the commercially fabricated fuel. Four-point bend testing was conducted on the irradiated U-10Mo samples to generate the fuel material properties, including the modulus of elasticity and the bending strength. Although the material behaves in a brittle manner due to the accumulated porosity, a general trend of strength and modulus reduction was found as fission density increases. The data produced was evaluated using both Weibull statistics and a modulus degradation model with recommendations provided.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2021

The effects of microstructures and radiation damage on the deformation behavior of a HT-9 alloy using microtensile testing

Understanding the influence of radiation damage on the mechanical properties of HT-9 and other tempered martensitic alloys is part of the mission in developing radiation-tolerant materials for the next generation of nuclear reactors. Although there has been extensive data on the macroscopic mechanical properties of the irradiated HT-9 alloys and microstructural changes, it is not well-understood how radiation damage and the resulting microstructural changes influence the local mechanical properties. In this study, we utilized in situ SEM microtensile testing to investigate the deformation behavior of specific martensitic boundaries in 1 dpa proton-irradiated HT-9 and answered the question of what is the weakest link. Additionally, we provided the direct observation of the failure modes of microtensiles containing high angle and low angle martensitic boundaries. In the unirradiated condition, the deformation is ductile and no martensitic boundary failure is observed. In the irradiated condition, the high angle martensitic boundaries are more susceptible to radiation-induced boundary failure as compared to the low angle martensitic boundaries.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2021

Thermal-Hydrological-Mechanical Modelling of Stockton University Reservoir Cooling System, Fine Scale Stress Test Modelling

Mesh, properties, initial conditions, injection/withdrawal rates for modelling thermal, hydrological, and mechanical effects of fluid injection to and withdrawal from ground for Stockton University reservoir cooling system (aquifer storage cooling system), Galloway, New Jersey, for unscheduled two hour injection at 133 % designed capacity, on fine scale grid, with some results. Second simulation of J.T. Smith, E. Sonnenthal, P. Dobson, P. Nico, and M. Worthington, 2021. Thermal-hydrological-mechanical modeling of Stockton University reservoir cooling system, Proceedings of the 46th Workshop on Geothermal Reservoir Engineering, Stanford University, SGP-TR-218, from which Figures 6-9, pertain.

15 GEOTHERMAL ENERGY↗

DOE OSTI2024

Size effect characteristics and influences on fatigue behavior of laser powder bed fusion of thin wall GRCop-42 copper alloy

Size effects, influencing a material's strength, elongation, fatigue limit, and longevity, depend on the operative and dominant deformation and failure mechanisms. This study explores the size effects in additive manufactured (AM) GRCop-42 (Cu-4at%Cr-2at%Nb) thin wall structures fabricated via laser-powder bed fusion (L-PBF) and their impact on fatigue life. The influence of internal defects and surface topography on the fatigue life of specimens in both as-built and hot isostatic pressed (HIP) conditions across different thicknesses is investigated. Where micro-computed tomography (μCT) was used to quantify the internal porosity of as-built, pristine HIP'd, and fatigued HIP'd specimens, and laser microscopy was employed to quantify the surface topography of specimens prior to fatigue. Additionally, quasi-static tests were used to establish baseline mechanical properties (i.e. yield strength (YS), ultimate tensile strength (UTS), and elongation) to frame fatigue testing conditions. Results indicate a significant enhancement in fatigue life for HIP'd specimens for both thicknesses, with internal defects depicting a greater impact than surface topography. Furthermore, fractographic analysis suggests that thicker specimens exhibit higher resistance to crack propagation during fatigue testing in the absence of substantial porosity. Thus, the size effects observed on the fatigue life of L-PBF GRCop-42 appears to be dominated by internal defects.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Mechanical Testing of FeCrAl Tubing

The axial tensile properties of C26M tube were successful measured at Los Alamos National Laboratory. Test were conducted at a constant strain rate of 10 -3 s -1 and three different temperatures (22, 300, and 600°C). As typically expected, an increase in the testing temperature lead to a decrease in both the yield stress (YS), from 710 to 273 MPa, and ultimate tensile strength (UTS), from 730 to 290 MPa. The ultimate tensile strength was observed almost immediately post-yielding for all test conditions, and thus the uniform elongation was limited to 1.2-1.6%. The total elongation of the 600°C specimens was notably higher (~47%) than both the 22 and 300°C specimens, which exhibited a similar response (~10%).

36 MATERIALS SCIENCE↗

NASA NTRS1978

Measurement of the time-temperature dependent dynamic mechanical properties of boron/aluminum composites

A flexural vibration test and associated equipment were developed to accurately measure the low strain dynamic modulus and damping of composite materials from -200 C to over 500 C. The basic test method involves the forced vibration of composite bars at their resonant free-free flexural modes in a high vacuum cryostat furnace. The accuracy of these expressions and the flexural test was verified by dynamic moduli and damping capacity measurements on 50 fiber volume percent boron/aluminum (B/Al) composites vibrating near 2000 Hz. The phase results were summarized to permit predictions of the B/Al dynamic behavior as a function of frequency, temperature, and fiber volume fraction.

Dicarlo, J. A.↗

NASA NTRS1991

The effects of multiple repairs on Inconel 718 weld mechanical properties

Inconel 718 weldments were repaired 3, 6, 9, and 13 times using the gas tungsten arc welding process. The welded panels were machined into mechanical test specimens, postweld heat treated, and nondestructively tested. Tensile properties and high cycle fatigue life were evaluated and the results compared to unrepaired weld properties. Mechanical property data were analyzed using the statistical methods of difference in means for tensile properties and difference in log means and Weibull analysis for high cycle fatigue properties. Statistical analysis performed on the data did not show a significant decrease in tensile or high cycle fatigue properties due to the repeated repairs. Some degradation was observed in all properties, however, it was minimal.

Russell, C. K.↗

NASA NTRS1986

Structure-to-property Relationships in Addition Cured Polymers 2: Resin Tg Composite Initial Mechanical Properties of Norbornenyl Cured Polyimide Resins

PRM (polymerization of monomeric reactants) methodology was used to prepare thirty different polyimide oligomeric resins. Monomeric composition as well as chain length between sites of crosslinks were varied to examine their effects on glass transition temperature (Tg) of the cured/postcured resins. An almost linear correlation of Tg versus molecular distance between the crosslinks was observed. An attempt was made to correlate Tg with initial mechanical properties (flexural strength and interlaminar shear strength) of unidirectional graphite fiber composites prepared with these resins. However, the scatter in mechanical strength data prevented obtaining as clear a correlation as was observed for the structural modification/crosslink distance versus Tg. Instead, only a range of composite mechanical properties was obtained at the test temperatures studied (room temperature, 288 and 316 C). Perhaps more importantly, what did become apparent during the attempted correlation study was: (1) that PMR methodology could be used to prepare composites from resins that contain a wide variety of monomer modifications, and (2) that these composites almost invariably provided satisfactory initial mechanical properties as long as the resins selected were melt processable.

Alston, W. B.↗

NASA NTRS1986

Structure-to-property relationships in addition cured polymers. II - Resin Tg and composite initial mechanical properties of norbornenyl cured polyimide resins

PRM (polymerization of monomeric reactants) methodology was used to prepare thirty different polyimide oligomeric resins. Monomeric composition as well as chain length between sites of crosslinks were varied to examine their effects on glass transition temperature (Tg) of the cured/postcured resins. An almost linear correlation of Tg versus molecular distance between the crosslinks was observed. An attempt was made to correlate Tg with initial mechanical properties (flexural strength and interlaminar shear strength) of unidirectional graphite fiber composites prepared with these resins. However, the scatter in mechanical strength data prevented obtaining as clear a correlation as was observed for the structural modification/crosslink distance versus Tg. Instead, only a range of composite mechanical properties was obtained at the test temperatures studied (room temperature, 288 and 316 C). Perhaps more importantly, what did become apparent during the attempted correlation study was: (1) that PMR methodology could be used to prepare composites from resins that contain a wide variety of monomer modifications, and (2) that these composites almost invariably provided satisfactory initial mechanical properties as long as the resins selected were melt processable.

Alston, William B.↗

DOE OSTI2022

Direct ink write multi-material printing of PDMS-BTO composites with MWCNT electrodes for flexible force sensors

Here, with recent advances of additive manufacturing technology, direct ink write (DIW) printing has allowed to incorporate multi-material printing of various materials with freedom of design and complex geometric shapes to complete functional sensors in a one-step fabrication. This paper introduces the use of DIW 3D printing of polydimethylsiloxane (PDMS) with barium titanate (BTO) filler as stretchable composites with tunable piezoelectric properties that can be used for force sensors applications. To improve the bonding between stretchable piezoelectric composites and electrodes, multi-walled carbon nanotubes was included in the fabrication of electrodes at a fixed ratio of 11 wt. %. The alignment of the BTO dipoles was achieved through corona poling method, which applies an electric charge on the surface layer of the functional material, aligning the dipoles in the desired direction and thus gaining the piezoelectricity. Different BTO mixing ratios (10–50 wt. %) were evaluated in order to obtain tunable piezoelectric properties and compare the sensitivity with respect their elastic properties. Tensile testing and piezoelectric testing were carried out to characterize mechanical and piezoelectric properties. Results showed that fabricated PDMS with 50 wt. % BTO gave the highest piezoelectric coefficient (d 33 ) of 11.5 pC N -1 and with an output voltage of 385 mV under compression loading of >200 lbF. This demonstrates feasibility of using multi-material DIW printing to fabricate piezoelectric force sensors with integrated electrodes in one-step without compromising the flexibility of the material.

36 MATERIALS SCIENCE↗