Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “internal combustion engines”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Evaluating an Eco-Cooperative Automated Control System

The paper evaluates an Eco-Cooperative Automated Control (Eco-CAC) system on a large-scale network considering a combination of internal combustion engine vehicles (ICEVs), hybrid electric vehicles (HEVs), and battery-only electric vehicles (BEVs) in a microscopic traffic simulation environment. We used a novel integrated control system that: (1) routes ICEVs, HEVs, and BEVs in a fuel/energy-efficient manner; (2) selects vehicle speeds based on anticipated traffic network evolution; (3) minimizes vehicle fuel/energy consumption near signalized intersections; and (4) intelligently modulates the longitudinal motion of vehicles along freeways within a cooperative platoon to minimize fuel/energy consumption. The study tested the system using the INTEGRATION software on the Los Angeles (LA), U.S., downtown network for three different demand levels: no congestion, mild congestion, and heavy congestion. The results demonstrated that the Eco-CAC system effectively reduces vehicle fuel and energy consumption, travel time, total delay, and stopped delay in heavily congested conditions. However, different vehicle compositions produced different results. In particular, the maximum energy consumption savings for BEVs (36.9%) for a current vehicle composition occurred at a 10% market penetration rate (MPR) of connected automated vehicles (CAVs) in mild congestion, while the maximum savings for a future vehicle composition (35.5%) occurred at a 50% CAV MPR in no congestion. The system reduced fuel consumption for ICEVs and HEVs by up to 5.4% and 6.3% at a 25% CAV MPR in heavy congestion for current and future vehicle compositions, respectively. However, the system increased total fuel consumption by up to 4.6% at a 50% CAV MPR in no congestion for a current vehicle composition. The study demonstrates that the effectiveness of the Eco-CAC system depends on traffic conditions, including congestion level, network configuration, CAV MPR, and vehicle composition.

Engineering↗
DOE OSTI2021

Determination of a most representative cycle from cylinder pressure ensembles via statistical method using distribution skewness

In internal combustion engine research, cylinder pressure measurements provide valuable information about the underlying thermodynamic and combustion processes, and are typically collected in ensembles of several 100 traces. Although in some particular fields of combustion research all traces are analyzed, in most cases only one trace is studied because analyzing all the traces is impractical due to the large number of collected samples. Instead, an ensemble-averaged pressure trace is commonly calculated and used for analysis. However, this pressure trace is highly smoothed and dynamic information is lost during the averaging process. With the average trace, pressure rise rates are lower and pressure oscillations such as the ones resulting from combustion knock are lost. In this work, a statistical method was developed to determine the “most representative cycle,” which is the cycle from the ensemble that has the pressure trace most representative of the engine operating condition. Eleven characteristic parameters are computed from each pressure trace and probabilistic distributions are obtained for each of the parameters using all the traces in the ensemble. Finally, the most representative cycle is selected by means of a cost function minimization. The benefits of this method are illustrated using experimental data from four very different engine platforms, under four different combustion modes and over a range of operating conditions.

42 ENGINEERING↗
DOE OSTI2023

Development and evaluation of a skeletal mechanism for EHN additized gasoline mixtures in large Eddy simulations of HCCI combustion

Advanced Low Temperature Combustion modes, such as the Sandia proposed Additive-Mixing Fuel Injection (AMFI), can unlock significant potential to boost fuel conversion efficiency and ultimately improve the energy conversion of internal combustion engines. This is a novel improved combustion process that is enabled by supplying small (<5%) variable amounts of autoignition improver to the fuel to enhance the engine operation and control. Common, diesel-fuel ignition-quality enhancing additive, 2-ethylexyl nitrate (EHN), is doped into gasoline to enable Sandia LTGC + AMFI combustion. This manuscript focuses on the development of a reduced sub-mechanism for EHN chemical kinetics at engine relevant conditions that is implemented into a skeletal mechanism for chemical kinetic studies of gasoline surrogate fuels. The mechanism validation utilized zero-dimensional numerical simulations and comparison to shock tube ignition-delay data of pure and EHN-doped n-heptane. Additional validation is presented with Homogeneous Charge Compression-Ignition (HCCI) engine data of pure and EHN-doped research-grade E10 gasoline. Then, the mechanism was deployed in a 3-D computational fluid dynamics (CFD) using Large Eddy Simulations (LES) to model the HCCI engine experiments of 0.4% vol EHN additized E10 gasoline at several equivalence ratios. Simulations showed a very good performance of the mechanism, and the model accurately reproduced (a) the ignition point, (b) combustion phasing, (c) combustion duration, and (d) the peak of the heat release rates of the engine experiments. The results show that EHN promotes Low-Temperature Heat Release, ultimately driving the gasoline to autoignite at thermodynamic conditions where the fuel would not otherwise ignite. Overall, this work demonstrates a viable reduced chemical-kinetic mechanism for EHN and shows that it can be combined with a skeletal gasoline mechanism for CFD-LES analysis of well-mixed LTGC that matches well with experimental results. The CFD-LES analysis also shows the spatial distribution of EHN-fuel interactions that control the autoignition throughout the combustion chamber.

Guleria, Gaurav↗
DOE OSTI2026

Autonomie Simulation Datasets in Support of U.S. DOT-NHTSA Advanced Vehicle Technology Research

Understanding how new vehicle technologies affect fuel economy and energy use is critical to the regulatory work performed by the U.S. Department of Transportation’s National Highway Traffic Safety Administration (NHTSA), which sets Corporate Average Fuel Economy (CAFE) standards under the Energy Policy and Conservation Act of 1975. In order to support this work, Argonne National Laboratory uses Autonomie, a full-vehicle simulation tool, to evaluate advanced powertrain architectures and their effects on vehicle energy consumption and performance. A wide range of vehicle classes has been assessed (i.e., internal combustion engine vehicles, hybrid electric vehicles, plug-in hybrid electric vehicles, battery-electric vehicles, and fuel cell electric vehicles), as well as the effects of various technology improvements such as lightweighting, aerodynamic refinements, and low-rolling-resistance tires. Simulations have been run across multiple drive cycles to capture fuel and electricity use under realistic operating conditions. The resulting datasets include detailed vehicle-level results, model assumptions, and validation reports, all of which have been made publicly available through NHTSA in support of the 2023 notice of proposed rulemaking covering light-duty vehicles for model years 2027 to 2035. These data are critical to stakeholders working in fuel economy regulation, vehicle technology assessment, and energy policy analysis.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2021

Minimizing Energy Use of Mixed-Fleet Public Transit for Fixed-Route Service

Affordable public transit services are crucial for communities since they enable residents to access employment, education, and other services. Unfortunately, transit services that provide wide coverage tend to suffer from relatively low utilization, which results in high fuel usage per passenger per mile, leading to high operating costs and environmental impact. Electric vehicles (EVs) can reduce energy costs and environmental impact, but most public transit agencies have to employ them in combination with conventional, internal-combustion engine vehicles due to the high upfront costs of EVs. To make the best use of such a mixed fleet of vehicles, transit agencies need to optimize route assignments and charging schedules, which presents a challenging problem for large transit networks. We introduce a novel problem formulation to minimize fuel and electricity use by assigning vehicles to transit trips and scheduling them for charging, while serving an existing fixed-route transit schedule. We present an integer program for optimal assignment and scheduling, and we propose polynomial-time heuristic and meta-heuristic algorithms for larger networks. We evaluate our algorithms on the public transit service of Chattanooga, TN using operational data collected from transit vehicles. Our results show that the proposed algorithms are scalable and can reduce energy use and, hence, environmental impact and operational costs. For Chattanooga, the proposed algorithms can save $145,635 in energy costs and 576.7 metric tons of CO 2 emission annually.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2021

Temperature Effects on Droplet Oscillation Decay with Application to Fuel Property Measurement

Observation of oscillation decay in droplets has been shown to be an effective approach in determining physical properties such as viscosity and surface tension for emerging biofuels using μl quantities. Herein this work extends the approach to higher temperatures relevant to fuel injection conditions for internal combustion engines. Experiments are conducted that use high-resolution strobed imaging of moving, heated, μm-sized, fuel droplets to capture shape oscillation decay through image processing and analysis. Two fuels are investigated, iso-butanol and a primary reference fuel (PRF 84), which is a mixture of iso-octane and n-heptane. A piezoelectric droplet generator is used to generate a continuous train of single droplets, which are given an initial perturbation and subsequently undergo damped oscillations, captured using strobed imaging. Surface tension and viscosity calculated at four different temperatures ranging from 30°C-55°C using the frequency and decay time associated with the fundamental mode are found to be within ~ 10% of reference values obtained from the literature. Complementary numerical simulations are performed that utilize a volume-of-fluid approach to track transient droplet oscillation phenomena along with heat and mass transfer in a 2D axisymmetric domain. Simulations, where droplet size and temperature can be independently varied, capture an expected decrease in oscillation frequency and increase in decay time, with increase in fuel temperature. The simulations are further used to study the relative contribution to deviations in surface tension and viscosity predictions due to heat and mass transfer from the droplet, as well as viscous effects violating the inviscid flow assumption in the droplet oscillation theory. Mass loss effects are found to be negligible. Temperature change due to heat transfer is found to have the next highest sensitivity, particularly for the more volatile PRF 84, which has a lower viscosity and associated Ohnesorge number. For isobutanol, which has a higher viscosity and Ohnesorge number, viscous effects contribute the most to deviation in fuel property predictions.

09 BIOMASS FUELS↗
DOE OSTI2020

Evaporation Sub-model Development for Volume of Fluid (eVOF) Method Applicable to Spray-Wall Interaction Including Film Characteristics with Validation at High Pressure and Temperature Conditions (Final Report)

Internal combustion engines have seen a great evolution over the last several decades through application of high pressure direct injection, multiple injections, and other technologies to reduced fuel consumption, NOx, and PM. Although combustion systems with advanced injection strategies have been studied extensively, there exists a significant fundamental knowledge gap on the fuel-spray interactions with the piston surface and chamber walls. Advanced computational codes validated with experimental techniques have to be developed for accurate representation of the drop impingement, fuel film formation, and vaporization. Current engine CFD spray models utilize a Lagrangian framework for modeling which lacks critical considerations of the physics pertaining to these interactions and thus requiring extensive parameterization, tuning and validation. The team from Michigan Technological University, University of Massachusetts Dartmouth, and Argonne National Laboratory is composed of experts in sprays, combustion, engines and CFD with a wide spectrum of knowledge including specific expertise in the area under consideration. In the proposed work, a VOF modeling approach has been adopted for the spray-wall interaction, film formation and spreading, and vaporization. With the inclusion of a vaporization submodel, a more predictive and accurate simulation of the spray-film was performed without extensive need of parameterization and tuning. Extensive experimentation of the spray-wall interaction under the range of conditions matching the thermodynamic and surface temperatures that occur in diesel and gasoline engines were conducted to validate the SWI submodels and for development of the evaporation sub-model, which has been implemented in the Converge software.

42 ENGINEERING↗
DOE OSTI2020

Evaporation Submodel Development for Volume of Fluid (eVOF) Method Applicable to Spray-Wall Interaction Including Film Characteristics with Validation at High Pressure and Temperature Conditions

Internal combustion engines have seen a great evolution over the last several decades through application of high pressure direct injection, multiple injections, and other technologies to reduced fuel consumption, NOx, and PM. Although combustion systems with advanced injection strategies have been studied extensively, there exists a significant fundamental knowledge gap on the fuel-spray interactions with the piston surface and chamber walls. Advanced computational codes validated with experimental techniques have to be developed for accurate representation of the drop impingement, fuel film formation, and vaporization. Current engine CFD (Computational Fluid Dynamics) spray models utilize a Lagrangian framework for modeling which lacks critical considerations of the physics pertaining to these interactions and thus requiring extensive parameterization, tuning and validation. The team from Michigan Technological University, University of Massachusetts Dartmouth, and Argonne National Laboratory is composed of experts in sprays, combustion, engines and CFD with a wide spectrum of knowledge including specific expertise in the area under consideration. In the proposed work, a VOF (Volume of Fluid) modeling approach has been adopted for the spray-wall interaction, film formation and spreading, and vaporization. With the inclusion of a vaporization submodel, a more predictive and accurate simulation of the spray-film was performed without extensive need of parameterization and tuning. Extensive experimentation of the spray-wall interaction under the range of conditions matching the thermodynamic and surface temperatures that occur in diesel and gasoline engines were conducted to validate the SWI submodels and for development of the evaporation submodel, which has been implemented in the flow solver.

42 ENGINEERING↗
DOE OSTI2020

Demonstration of μCHP in Light Commercial Hot Water Applications

Internal combustion engine driven combined heat and power (CHP) systems produce power while the waste heat is recovered and used for another purpose. For µCHP systems (less than 50kWe output) overall efficiencies can reach over 90% for products currently on the market throughout the world. On a fuel basis this offers an advantage over using grid-based power and another fuel for heat. Additionally, the cost of natural gas on an energy unit basis is significantly less expensive than electric power. This difference can lead to substantial savings for the end user of a CHP system. In some parts of the world, particularly Germany and Japan, µCHP has become a common part of the heat and distributed generation equipment mix. Market analysis conducted in 2012 showed that in North America there is potential of a 5,300 units per year market for µCHP, resulting in an annual energy savings of approximately 13.5 TBtu and more than $84 million in annual customer savings. However, µCHP still has not seen much market penetration in North America. This study helps to identify some of the reasons why, address roadblocks that still need to be overcome and provide experience to established best practices. Nine commercial sites were initially identified (fitness club, surgical center, senior community, resort and spa, commercial laundry, two multi-family housing, restaurant and manufacturing facility). Systems from two different manufacturers were installed at five sites total, but due to unforeseen circumstances, only three of those sites were finally commissioned: test data were collected by Oak Ridge National Laboratory. While not all systems were installed as intended, the project resulted in the following key findings: Micro combined heat and power is an unfamiliar technology for building owners and plumbing and electrical contractors that serve the buildings most suited for µCHP. Manufacturers will need to be aggressive in providing training and providing broad support to successfully bring the technology to market.; The proper integration of µCHP into other building systems is the most critical part of a successful installation. Manufacturers will need to be able to provide the expertise to train, advise and support the mechanical contractors during the design and installation of the heat integration system.; Regulations governing µCHP varies across the country. There are a few UL standards (UL 2200 and UL 1741) that apply nationally. Emissions are governed by EPA except in California where the California Air Resources Board (CARB) has established their own standard. Requirements that dictate installation and interconnection are dependent on local building codes and local utility processes and requirements. Some out of date building codes do not offer clear guidance for these requirements, leading to confusion. This makes developing training and determining broadly applicable best practices difficult.; Installation costs of µCHP are a key factor in making an installation successful. It is critical that these costs and all national, state and local regulations be understood and accounted for by all parties involved in the installation before a project is undertaken.; A robust customer service organization is important to meet the needs of the customers. These systems require annual maintenance and service and local capability is needed to keep costs inline.

03 NATURAL GAS↗
DOE OSTI2021

Used Plug-in Electric Vehicles as a Means of Transportation Equity in Low-Income Households

This report examines improving the equity of low-income households through access to reliable means of transportation. Used plug-in electric vehicles (PEVs) can serve as a low-cost and low-maintenance means of transport for low-income households. Zero tail-pipe emissions from PEVs is also a benefit of these drivetrain compared to internal combustion engine vehicles (ICEVs). Barriers to the adoption of the used PEVs, and incentives that may address these barriers were reviewed.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2020

Model Development for Multi-Component Fuel Vaporization and Flash Boiling

The objectives of this project are to improve the multi-component fuel droplet and film vaporization models used in internal combustion engine simulation, and to develop a comprehensive model to predict the characteristics of multi-component flash boiling spray. This work explores two approaches to fuel composition treatment for modeling multi-component fuel vaporization: one based on discretization and surrogates, and the other based on continuous thermodynamic distribution of fuel properties. The experimental data collected for model validation are done under three fuel form factors: droplet, spray, and thin film. The study on sprays also include experimentation under non-flash and flash boiling conditions, a phenomenon that enhances fuel vaporization. The main goals of this work are: Design and develop a multi-component fuel droplet and wall film vaporization model using both discrete and continuous thermodynamics methods. Design and develop an analytical model for multi-component flash boiling. Integrate the multi-component droplet and film model into multi-dimensional engine calculations to predict the fuel vaporization process under engine operation condition. Conduct multi-component droplet and fuel film vaporization experiments in a non-combusting chamber to verify the proposed vaporization models. Characterize flash boiling phenomena of multi-component fuel sprays by optical and laser diagnostic techniques. This report will detail the experimental setup and the numerical basis for developing a model to achieve the main goals listed above. Key features of observed multi-component fuel vaporization will be summarized at the end of each experimental sections, and corresponding model performance evaluation will be presented at the end of each model development section.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2020

Medium-duty Urban Range Extended Connected Powertrain (Final Scientific Technical Report)

The project goal is to develop and demonstrate a Class 4 delivery vehicle that reduces fuel consumption by 50% or more when compared to an equivalent vehicle with a conventional internal combustion engine (ICE) powertrain driven on a comparable duty cycle. This shall be achieved using a plug-in hybrid electric (PHEV) configuration that optimizes the efficiency of the ICE. The proposed solution aims to be commercially viable for fleets to procure the system without additional incentives. To accomplish this, commercialized light-duty vehicle electric drive components shall be used. A PHEV configuration for Class 4 MD/HD vocational vehicles using commercialized light-duty vehicle electric drive components will require the development of a new topology for the hybrid powertrain applicable to medium-duty vehicles. Prior research indicates that an identified novel power split device could provide a fuel economy improvement potential of up to 51%. Utilizing an advanced battery management algorithm that will allow operation closer to the battery limits, the project will minimize battery capacity to achieve the desired performance results while maintaining the cost target for high commercialization. The solution must be cost effective to purchase and integrate into a Class 4 delivery vehicle, deliver the intended fuel economy improvement, and perform as well, or better, than the current conventional ICE powertrain. MD/HD vehicles typically require higher power, which is one factor that results in high costs for the powerful electric machines typical in larger HEV/PHEV systems. A key element in the project is the use of commercially available Bosch electric drive components (e.g., motors, batteries, and power electronics) from the larger passenger vehicle segment. This leverages the economies of scale to decrease cost and improve reliability beyond current purpose-built low-volume commercial vehicle components. These innovations will result in a game-changing PHEV system that meets DOE’s 50% fuel consumption reduction target, grants the vehicle an uncompromised driving range, and achieves the cost point for widespread adoption.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2021

Comprehensive Total Cost of Ownership Quantification for Vehicles with Different Size Classes and Powertrains

In order to accurately compare the costs of two vehicles, the total cost of ownership (TCO) should consist of all costs related to both purchasing and operating the vehicle. This TCO analysis builds on previous work to provide a comprehensive perspective of all relevant vehicle costs of ownership. In this report, we present what we believe to be the most comprehensive explicit financial analysis of the costs that will be incurred by a vehicle owner. This study considers vehicle cost and depreciation, financing, fuel costs, insurance costs, maintenance and repair costs, taxes and fees, and other operational costs to formulate a holistic total cost of ownership and operation of multiple different vehicles. For each of these cost parameters that together constitute a comprehensive TCO, extensive literature review and data analysis were performed to find representative values in order to build a holistic TCO for vehicles of all size classes. The light- and heavy-duty vehicles selected for analysis in this report are representative of those that are on the road today and expected to be available in the future. Important additive analyses in this study include systematic analysis of vehicle depreciation, in-depth examination of insurance premium costs, comprehensive maintenance and repair estimates, analysis of all relevant taxes and fees, and considerations of specific costs applicable to commercial vehicles. We find that cars depreciate faster than light trucks and that older plug-in electric vehicles have a greater depreciation rate than newer electric vehicles. Light-duty vehicle (LDV) insurance costs show comparable costs for different powertrains, and lower costs for larger size classes. Medium- and heavy-duty vehicle (MHDV) insurance costs vary significantly by vocation. Electric and electrified powertrains have lower maintenance and repair costs than internal combustion engine (ICE) powertrains for all vehicle sizes, relative to vehicle price. MHDV maintenance and repair costs depend heavily on vocation and duty cycle. LDV taxes and fees are comparable across powertrain types and size classes, though marginally higher registration fees exist for alternative fuel vehicles. MHDV fees depend on the vocation, weight rating, and state. Many electric tractor trailers would be affected by additional battery weight, reducing the available payload capacity, and this cost can be substantial. Electric vehicle charging for commercial vehicles can be time-consuming; labor rates can cause this cost to dominate TCO. With improved knowledge of each of the cost components, we calculate a lifetime TCO for comparison across vehicles of different types and attributes. For a simulated small sport utility vehicle in 2025, modeled using Autonomie, the hybrid electric vehicle (HEV) has the lowest cost, followed by the conventional ICE vehicle. For MHDV, TCO can be drastically different depending on the vocation. Long-haul vehicles typically have the lowest per-mile costs. Excluding labor costs, the class 4 delivery has a comparable TCO to the day cab. Vocational trucks, refuse trucks, and transit buses have a high per-mile cost of ownership due to maintenance and insurance. For all of these vehicles, the cost of operating the vehicle is heavily weighted by the labor of the driver, followed by the fuel costs. While the HEV begins as the lowest cost powertrain for passenger vehicles, fuel cells are forecast to reach cost parity by 2030 when hydrogen prices reach $\$ 5$/kg while battery electric vehicles (BEV) reach cost parity by 2035 at a battery cost of $\$ 98$ per usable kWh of capacity, with these two technologies being the lowest cost in 2050. For the class 8 day cab tractor, the HEV and ICE vehicle begin as the lowest cost powertrains, and the 250-mile BEV reduces in cost from the most expensive to the least expensive by 2030.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2021

Developing an Eco-Cooperative Automated Control System (Eco-CAC)

The goal of the project was to develop a novel Eco-Cooperative Automated Control (Eco-CAC) system that integrates vehicle dynamics (VD) control with connected and automated vehicle (CAV) applications. In particular, the team developed a novel integrated control system that (1) routes vehicles in a fuel/energy-efficient manner for internal combustion engine vehicles (ICEVs), battery-only electric vehicles (BEVs), and hybrid electric vehicles (HEVs); (2) selects vehicle speeds based on anticipated traffic network evolution; (3) minimizes vehicle fuel/energy consumption near signalized intersections; and (4) intelligently modulates the longitudinal motion of vehicles within a cooperative platoon to minimize its fuel/energy consumption.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2021

Lightweight High-Temperature Alloys Based on the AlFeSi System

Automotive applications need low-cost, lightweight, high-temperature alloys to enhance efficiencies in systems such as internal combustion engines. The aluminum-iron-silicon (Al-Fe-Si) system provides an opportunity to develop such a material, as it comprises three of the lowest cost elements abundant in nature. Specifically, the $τ_{11}$-Al 4 Fe 1.7 Si (historically called $τ_{10}$) ternary intermetallic phase is a lightweight and low-cost phase with promising mechanical properties at high temperatures. However, the $τ_{11}$-Al 4 Fe 1.7 Si phase has a narrow compositional range, which should be expanded to use this alloy at a commercial scale. To increase this compositional range, equilibrium phase boundaries were expanded using alloy design strategies.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Validation of the HyRAM+ physics models for use with propane

The Hydrogen Risk Assessment Model Plus (HyRAM+) toolkit combines quantitative risk assessment with simulations of unignited dispersion, ignited turbulent diffusion flames, and indoor accumulation with delayed ignition of fuels. HyRAM+ is differentiated from HyRAM in that it includes models and leak data for other alternate fuels. The models of the physical phenomena need to be validated for each of the fuels in the toolkit. This report shows the validation for propane which is being used as a surrogate for autogas, which is a mixture of propane and butane and used in internal combustion engines in vehicles. For flame length comparisons, five previously published experiments from peer reviewed journals were used to validate our models. The validation looked at flame lengths and flame widths with respect to different leak diameters, mass flow rates, and source pressures. Most of the sources included more than one set of experimental data, which were collected using different methods (CCD cameras, IR visualization etc.). In general, HyRAM+ overpredicts the flame lengths by around 65%. For heat and radiation models, we compared the heat flux and radiation data reported from two different sources to the values calculated by HyRAM+. For higher mass flow rates, the HyRAM+ calculated flame length results gave a better estimate of what is found in the experiments (65% error), but a higher error (85%) is observed between the HyRAM+ calculated lengths and the experimental flame lengthsfor lower mass flows. Some differences can be attributed to outdoor environmental effects (i.e. wind speed) and uncertainties in jet flame shapes. The propane flame trajectory is predicted for a high Reynolds number case with Re = 12,500 and a low Reynolds number case where Re = 2,000. The Re=12,500 case which is momentum dominated matches well with the experimental flame trajectory, but the agreement for the bouancy driven low Reynolds number case is not as good. Dispersion modeling for unignited propane was also analyzed. We compared the mole fraction, mixture fraction, mean velocity, concentration half width, and inverse mass concentration over an axial distance from different credible journals to the values calculated by HyRAM+. The results display good agreement but generally, HyRAM+ predicts a wider profile for mole fraction and mixture fraction experiments. Overall, HyRAM+’s results are reasonable for predicting the flame length, heat flux, flame trajectory, and dispersion for propane and can be used in risk analyses

08 HYDROGEN↗
DOE OSTI2020

High-Dimensional Data-Driven Energy Optimization for MultiModal Transit Agencies

Transportation accounts for 28% of the total energy use in the United States and as such, it is responsible for immense environmental impact, including urban air pollution and greenhouse gas emissions, and may pose a severe threat to energy security. As we encourage mode shift from personal vehicles to public transit, it is important to consider that public transit systems still require substantial amounts of energy; for example, public bus transit services in the U.S. are responsible for at least 19.7 million metric tons of CO 2 emission annually. As such it is absolutely crucial that we study the bottlenecks to energy efficiency in public transit and develop new algorithms that can help the public transit agencies, especially those that are still operating mixed fleets, which may consist of Electric vehicles (EVs), hybrids (HEVs), and internal combustion engine vehicles (ICEVs), optimize the operations by deciding which vehicles are assigned to serving which transit trips.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2021

Electrification FY2020 Annual Progress Report

The Electric Drive Technologies (EDT) program’s mission is to conduct early-stage research and development on transportation electrification technologies that accelerate the development of cost-effective and compact electric traction drive systems that meet or exceed performance and reliability requirements of internal combustion engine (ICE)-based vehicles, thereby enabling electrification across all light-duty vehicle types.

33 ADVANCED PROPULSION SYSTEMS↗