Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “in situ processing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

In-situ qualification and physics-based process design for aerosol jet printing via spatially correlated light scattering measurements

Aerosol jet printing is a contactless, digital, and additive technique broadly used for manufacturing flexible, hybrid, and conformal electronics. However, batch-to-batch variability has hindered widespread industry adoption and scaling to production volumes. Recently, light scattering measurements have emerged as a tool to measure aerosol volume fraction – a key parameter determining deposition rate – and have proven an effective feedback source for closed loop control on timescales ranging from minutes to hours. Here, the efficacy of light scattering measurements as a tool for in-situ qualification over shorter time durations is explored. To be the linear relationship between light scattering measurements and deposition rate was validated at 500 ms time intervals, allowing deposition rate to be mapped to positional coordinates and providing a new data stream to drive quality control assessments. Because light scattering measurements are indicative of a physical process parameter, they were substituted into equations for resistance and sheet resistance, resulting in predictions nominally within 10% of measured values for sets of printed devices. Finally, to highlight a more active utility, light scattering measurements were employed in a print repair framework, successfully repairing prints with randomly induced defects to within 5% of the measured resistance of a control set.

36 MATERIALS SCIENCE↗
DOE OSTI2021

On the Structural Transformation of Ni/BaH 2 During a N 2 -H 2 Chemical Looping Process for Ammonia Synthesis: A Joint In Situ Inelastic Neutron Scattering and First-Principles Simulation Study

The demand for decarbonizing the ammonia industry by using renewable energy has invoked increasing research interests into catalyst development for effective N 2 reduction under mild conditions. Hydride-based materials are among some of the emerging catalysts for ammonia synthesis at ambient pressure and low temperatures (< 673 K). A recent chemical looping process based on Ni/BaH 2 showed the most promise as it can realize ammonia production at a temperature as low as 373 K and under ambient pressure. However, the chemical transformation of the hydride catalyst at the molecular level remains unclear in this process. Here, we report detailed in situ neutron spectroscopy and diffraction investigations along with first-principles simulations on the structural transformation of Ni/BaH 2 during the nitridation and hydrogenation steps in the chemical looping process for ammonia synthesis. It was shown that a ball-milling process of the starting Ni/BaH 2 could significantly decrease the size of BaH 2 and increase the density of defects, thus potentially enhancing the reactivity of the hydride. The evolution from BaH 2 to barium imide (BaNH) was evidenced in the inelastic neutron scattering (INS) and neutron diffraction results during the N 2 reaction step. During the hydrogenation study, in addition to the recovery of BaH 2 , a possible intermediate species, N-deficient barium imide, was also detected. In comparing the N 2 and H 2 reaction steps, the neutron results indicate that the hydrogenation step appears more difficult than the nitridation step, confirming the facile N 2 fixation property of Ni/BaH 2 catalyst in ammonia synthesis.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS2001

Construction of Power Receiving Rectenna Using Mars- In-Situ Materials; A Low Energy Materials Processing Approach

It is highly desirable to have a non-nuclear power rich option for the human exploration of Mars. Utilizing a Solar Electric Propulsion, SEP, / Power Beaming architecture for a non-nuclear power option for a human Mars base potentially avoids the weather and dust sensitivities of the surface photovoltaic option. Further from Mars areosynchronous orbit near year round power can be provided. Mission analysis, however, concludes that ultra high (245 GHz) frequencies or laser transmission technologies are required for Mars landed mass competitiveness with the surface photovoltaic option if the receiving rectifying antenna "rectenna" is transported from Earth. It is suggested in this paper that producing rectenna in situ on Mars surface might make a more conventional 5.8 GHz system competitive with surface PV. The premium of a competitive, robust, continuous base power might make the development of a 10 plus MWe class SEP for human Mars mission a more attractive non-nuclear option.

Curreri, Peter A.↗
NASA NTRS2003

Capturing a failure of an ASIC in-situ, using infrared radiometry and image processing software

Failures in electronic devices can sometimes be tricky to locate-especially if they are buried inside radiation-shielded containers designed to work in outer space. Such was the case with a malfunctioning ASIC (Application Specific Integrated Circuit) that was drawing excessive power at a specific temperature during temperature cycle testing. To analyze the failure, infrared radiometry (thermography) was used in combination with image processing software to locate precisely where the power was being dissipated at the moment the failure took place. The IR imaging software was used to make the image of the target and background, appear as unity. As testing proceeded and the failure mode was reached, temperature changes revealed the precise location of the fault. The results gave the design engineers the information they needed to fix the problem. This paper describes the techniques and equipment used to accomplish this failure analysis.

infrared↗
NASA NTRS1990

On-line in-situ control of the resin transfer molding process

Resin transfer molding of three-dimensionally stitched fabrics promises to be a cost effective process for obtaining composite parts of exceptional strength. The technique eliminates many problems involving prepreg preparation, storage and layup. It replaces, on the other hand, the single step cure process with a two-stage impregnation and cure process. Of particular importance therefore is selecting and controlling the viscosity during impregnation and cure. The use of in-situ frequency-dependent electromagnetic sensors and the Loos-Springer model for selecting and controllng the processing properties of the resin transfer molding resin during impregnation and cure are discussed.

Kranbuehl, D.↗
DOE OSTI2020

Understanding KOtBu in atomic layer deposition – in situ mechanistic studies of the KNbO3 growth process

Functional coatings based on alkali metals have become increasingly attractive in the current shift towards sustainable technologies. While lithium-based compounds have a natural impact on batteries, other alkali metal compounds are important as replacements for toxic materials in a range of electronic devices. This is especially true for potassium, being a major component in e.g. K x Na 1-x NbO 3 (KNN) and KTa x Nb 1-x O 3 (KTN), with hope to replace Pb(Zr x Ti 1-x )O 3 (PZT) in piezo-/ferroelectric and electrooptic devices. ALD facilitates functional conformal coatings at deposition temperatures far below what is reported using other techniques and with excellent compositional control. The ALD growth of potassium-containing films using KO t Bu has, however, been unpredictable. Untraditional response to the pulse composition and precursor dose, severe reproducibility issues, and very high growth per cycle are some of the puzzling features of these processes. In this article, we shed light on the growth behavior of KO t Bu in ALD by in situ quartz crystal microbalance and Fourier transform infrared spectroscopy studies. We study the precursor's behavior in the technologically interesting KNbO 3 -process, showing how the potassium precursor strongly affects the growth of other cation precursors. We show that the strong hygroscopic nature of the intermediary potassium species has far-reaching implications throughout the growth. This helps not only to enhance the understanding of alkali metal containing compounds’ growth in ALD, but also to provide the means to control the growth of novel sustainable technological materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Gas pore correlations in laser powder bed fusion of Al6061

Additive manufacturing (AM) of metal materials based on powder bed fusion technology is widely used now in many industries. A known limitation of this type of manufacturing is the formation of gas pores in the bulk material. Here we present a combined X-ray imaging and mid-infrared pyrometry study of pore formation in side-by-side tracks of Al6061 for different processing conditions using both in-situ and post-processing analysis. By carefully quantifying the distributions and correlations of pore positions, we show that an existing pore in one track often catalyzes the formation of another pore in an adjacent track. In a raster scan strategy commonly used to construct bulk material, this phenomenon has the result of forming subsurface perforations, or lines of pores transverse to the scanning direction in a rastered patch. If controlled, this effect can be eliminated to improve the yield strength of the build, or exploited to create programmable failures for specific purposes.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Transformation of TiN to TiNO Films via In-Situ Temperature-Dependent Oxygen Diffusion Process and Their Electrochemical Behavior

Titanium oxynitride (TiNO) thin films represent a multifaceted material system applicable in diverse fields, including energy storage, solar cells, sensors, protective coatings, and electrocatalysis. This study reports the synthesis of TiNO thin films grown at different substrate temperatures using pulsed laser deposition. A comprehensive structural investigation was conducted by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), Non-Rutherford backscattering spectrometry (N-RBS), and X-ray absorption spectroscopy (XAS), which facilitated a detailed analysis that determined the phase, composition, and crystallinity of the films. Structural control was achieved via temperature-dependent oxygen in-diffusion, nitrogen out-diffusion, and the nucleation growth process related to adatom mobility. The XPS analysis indicates that the TiNO films consist of heterogeneous mixtures of TiN, TiNO, and TiO2 phases with temperature-dependent relative abundances. The correlation between the structure and electrochemical behavior of the thin films was examined. The TiNO films with relatively higher N/O ratio, meaning less oxidized, were more electrochemically active than the films with lower N/O ratio, i.e., more oxidized films. Films with higher oxidation levels demonstrated enhanced crystallinity and greater stability under electrochemical polarization. These findings demonstrate the importance of substrate temperature control in tailoring the properties of TiNO film, which is a fundamental part of designing and optimizing an efficient electrode material.

Cherono, Sheilah↗
NASA NTRS2012

In Situ Detection of Strong Langmuir Turbulence Processes in Solar Type III Radio Bursts

The high time resolution observations obtained by the WAVES experiment of the STEREO spacecraft in solar type III radio bursts show that Langmuir waves often occur as intense localized wave packets. These wave packets are characterized by short durations of only a few ms and peak intensities, which well exceed the supersonic modulational instability (MI) thresholds. These timescales and peak intensities satisfy the criterion of the solitons collapsed to spatial scales of a few hundred Debye lengths. The spectra of these wave packets consist of primary spectral peaks corresponding to beam-resonant Langmuir waves, two or more sidebands corresponding to down-shifted and up-shifted daughter Langmuir waves, and low frequency enhancements below a few hundred Hz corresponding to daughter ion sound waves. The frequencies and wave numbers of these spectral components satisfy the resonance conditions of the modulational instability (MI). Moreover, the tricoherences, computed using trispectral analysis techniques show that these spectral components are coupled to each other with a high degree of coherency as expected of the MI type of four wave interactions. The high intensities, short scale lengths, sideband spectral structures and low frequency spectral enhancements and, high levels of tricoherences amongst the spectral components of these wave packets provide unambiguous evidence for the supersonic MI and related strong turbulence processes in type III radio bursts. The implication of these observations include: (1) the MI and related strong turbulence processes often occur in type III source regions, (2) the strong turbulence processes probably play very important roles in beam stabilization as well as conversion of Langmuir waves into escaping radiation at the fundamental and second harmonic of the electron plasma frequency, fpe, and (3) the Langmuir collapse probably follows the route of MI in type III radio bursts.

Langmuir↗
DOE OSTI2024

Liquid Interfacial Electron Microscopy Identifies Nanogalvanic Corrosion in Pearlitic Steel

The nanoscale mechanisms of localized corrosion in low carbon steels have remained elusive due to the complexity of studying the degradative material behavior at nanoscale solid-liquid interfaces. We identified various steps in the nanogalvanic corrosion processes using in-situ liquid-cell scanning transmission electron microscopy (STEM) using a microfluidic holder by Hummingbird Scientific. Initial work, performed at low magnification, identified the initiation point on a 1018 low-carbon steel surface. This initiation point was determined to be a triple junction of two ferrite grains bridging a cementite grain in contact with a baseline electrolyte of 6 uM CO2 dissolved in a buffered (2.78 uM Na2SO4) aqueous solution, pH 6.1. The pre-etched low-carbon steel surface was prepared using focused ion beam lift-out procedures to extract a cross-section of the low-carbon steel surface, which then was thinned to about 150 nm and transferred to a SiN membrane microfluidic window. The transfer was made using a lift-out needle to attach the low-carbon steel lamella to the corner of the SiN window, and then Pt/C deposition held the lamella in contact with the window while it was released from the lift out needle. To identify the triple point on the low carbon steel lamella, prior to attachment on the SiN window, the sample was characterized for compositional variations with energy dispersive x-ray spectroscopy mapping, grain orientation and phase mapping with precession electron diffraction, and thickness mapping with energy filtered transmission electron microscopy. This pre-characterization prior to the in-situ experiment provided a map of the multiphase and multigrain structure, where the in-situ liquid cell imaging provided a clear understanding of the initiation point on the sample. These data were cross-correlated to paint a holistic picture of the triple junction site, enabling low electron-fluence in-situ snapshot imaging to avoid dominating the native corrosion reactions with effects from the incident electron beam. This initial result identified that localized, nanogalvanic corrosion at the phase interface was the dominant corrosion process in the low-carbon steel, so we next targeted the observation of an array of these nanogalvanic features phase boundaries in a pearlite grain. Near-surface ferrite/cementite phase interfaces that typify pearlitic low-carbon steel were extracted, pre-characterized, and imaged for the in-situ corrosion processes. The sample was a cross-section from a pearlite grain, with alternating ferrite and cementite grains that extended microns down from the pre-etched low-carbon steel pipe surface. After contact with a buffered aqueous solution, the phase boundaries between the ferrite and cementite began to dissolve, with observable material loss and thickness changes in the dark-field and bright-field STEM images. Within minutes, the corrosion front proceeded deeper into the material, claiming a thin layer of ferrite around all exposed phase boundaries before progressing laterally into the ferrite matrix, converting the ferrite to corrosion product normal to each buried cementite grain. Formation of the corrosion product causes a volumetric expansion, creating a lateral wedging force that mechanically ejects the cementite grains from their grooves and leaves behind percolation channels into the steel substructure. Rapid and deleterious, this nanogalvanic corrosion pathway represents an important target for understanding and preventing run-away degradation in this common building material. Observation of this corrosion mechanism was enabled by the combination of pre-characterization using standard structural, grain, and compositional analysis in the TEM, which provides maps for understanding the reaction propagation captured in low-dose, in-situ, liquid-cell STEM.

corrosion↗
NASA NTRSDate not supplied

The Additive Manufacturing Moment Measure - A Parallel Computation Technique for Determining Build Variance in the Laser Powder Bed Fusion Process

Additive manufacturing (AM) has unique process attributes that facilitate the creation of optimized, complex, and unique parts for aerospace applications. However, the multi-scale and complicated building process for AM parts can cause unexpected build conditions that result in microstructural variability within the deposited material. The need for richer datasets and computational modeling capabilities to improve AM process reliability is a consequence of this microstructural variability. A computational approach, referred to as the Additive Manufacturing Moment Measure (AM3), addresses this need by leveraging the way AM processes fuse material in precise, incremental steps. During the layering sequence, each previous step contributes to the condition of the current step at the center of the heat source. The precise steps can be selected to systematically create a time-space point field with co-located machine input and in-situ sensor data. The sequential nature of the AM process, coupled with nearest neighbor calculations, allows for a fully parallel computation for part-scale build profile analysis. The AM3 concept introduced here enables part-scale assessment directly from build files and in-situ process monitoring sensors alike. The AM moment measures were calculated for build point fields and compared with co-located in-situ and ex-situ nondestructive evaluation and optical microscopy observations. These comparisons permit a better understanding of how the sequential process actions can affect the quality of a laser powder bed fusion (LPBF) build. Details of the AM3technique will be discussed and compared to measured LPBF part characteristics. The AM3 results indicate a strong potential to advance the qualification process for aerospace applications.

Additive Manufacturing↗
DOE OSTI2022

AI-Enabled Discovery and Physics-Based Optimization of Energy Efficient Processing Strategies for Advanced Turbine Alloys (Final Technical Report)

In this project, the multi-organizational team of academic and industrial researchers from the University of Kentucky an aerospace and energy generation OEM partner has leveraged novel Digital Process Twin (DPT) models of process/structure interactions (i.e., process-induced surface integrity) to advance a paradigm of fully integrated computational materials engineering (ICME). Using efficient process models as the core of a digital process simulator for a reinforcement learning algorithm, the team has integrated industrial data and metrics of structure/performance/energy relationships and manufacturing-related energy metrics to optimize dynamic processing parameters for significantly improved life-cycle energy efficiency of advanced γ-TiAl low-pressure turbine (LPT) alloys, as indicated by a set of design relevant parameters (e.g., residual stresses and scrap rate). The key objective and anticipated outcome of the project was at least a 10% reduction in life-cycle embodied energy for a recently developed, γ-TiAl low-pressure turbine (LPT) alloy and nickel-based superalloy Inconel 718, through the adoption of the proposed AI-enabled process optimization approach. The final project outcomes significantly exceeded this original target, realizing manufacturing-related energy efficiency improvements of more than 130% for TiAl and up to 80% for Inconel 718. Rather than following the prevailing and highly inefficient empirical paradigm, the proposed study demonstrated the feasibility of adopting a digital, physics-based process design and optimization paradigm. The recurring need for manual intervention, rework, reinspection causes significant production bottlenecks and unnecessary expense associated with delivering the requisite component quality. The OEM partner, and turbine industry in general, expect to reap significant cost and resource savings if an AI-optimized set of parameters can be applied to specific machining operations. The technical scope of the proposed project involved the paving of a realistic path towards model-based and AI-enabled Integrated Computational Materials Engineering (ICME), and away from inefficient empirical process optimization and legacy manufacturing practices, which are no longer able to efficiently process novel high-performance turbine alloy materials. The project team will address the fundamental knowledge gap that currently exists within the ICME paradigm with respect to the process/structure/performance/energy impacts of finishing processes. While significant resources have been devoted to the ‘early stages’ of manufacturing, such as alloy design, primary and secondary processing, finishing processes have not been adequately integrated within ICME. To provide an actionable path towards model-based finishing process design (e.g., machining, burnishing, grinding, polishing), we will employ a novel AI-enabled process optimization paradigm, based on a computationally efficient, physics-based process simulator. Through limited experimental work to calibrate and validate our process simulator model via an advanced in-situ characterization technique and process optimization via reinforcement learning, the project will seek to demonstrate a viable alternative to the inefficient ‘legacy’ processing strategies, empirical testing and broad scope machining learning approaches, all of which fail to adequately consider complex process physics. The project team has identified an intermetallic γ-TiAl LPT alloy, which is currently being used as part of the OEM partner’s advanced gas turbine designs. This particular alloy poses significant manufacturing challenges during finishing operations, which limit the degree to which the current turbine design can be manufactured in an energy- and cost-efficient manner. Empirical testing and numerical modeling efforts to optimize processing parameters for γ-TiAl have not been able to resolve these manufacturing challenges, so the proposed physics-based AI-enabled optimization technology would offer a truly novel and transformative capability. The multi-organizational team of academic and industry experts from the UKY and the OEM partner will work together closely to demonstrate the analytical and experimental critical function and characteristic proof of concept of this novel approach.

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2022

Stem respiration and growth in a central Amazon rainforest

Tropical forests cycle a large amount of CO 2 between the land and atmosphere, with a substantial portion of the return flux due tree respiratory processes. However, in situ estimates of woody tissue respiratory fluxes and carbon use efficiencies (CUEW) and their dependencies on physiological processes including stem wood production (Pw) and transpiration in tropical forests remain scarce. In this work, we synthesize monthly Pw and daytime stem CO 2 efflux (ES) measurements over one year from 80 trees with variable biomass accumulation rates in the central Amazon. On average, carbon flux to woody tissues, expressed in the same stem area normalized units as ES, averaged 0.90 ± 1.2 µmol m -2 s -1 for Pw, and 0.55 ± 0.33 µmol m -2 s -1 for daytime ES. A positive linear correlation was found between stem growth rates and stem CO 2 efflux, with respiratory carbon loss equivalent to 15 ± 3% of stem carbon accrual. CUEW of stems was non-linearly correlated with growth and was as high as 77-87% for a fast-growing tree. Diurnal measurements of stem CO 2 efflux for three individuals showed a daytime reduction of ES by 15-50% during periods of high sap flow and transpiration. The results demonstrate that high daytime ES fluxes are associated with high CUE W during fast tree growth, reaching higher values than previously observed in the Amazon Basin (e.g. maximum CUEW up to 77-87%, versus 30-56%). The observations are consistent with the emerging view that diurnal dynamics of stem water status influences growth processes and associated respiratory metabolism.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS1993

Mullite Whiskers and Mullite-whisker Felt

The Naval Surface Warfare Center has developed processes for the preparation of mullite (3(Al2O3)(dot)2(SiO2)) whiskers and mullite-whisker felt. Three patents on the technology were issued in 1990. The processes are based on chemical reactions between AlF3, Al2O3, and SiO2. The felt is formed in-situ during the processing of shaped powdered precursors. It consists of randomly oriented whiskers which are mutually intergrown forming a rigid structure. The microstructure and properties of the felt and size of the whiskers can be modified by varying the amount of Al2O3 in the starting mixture. Loose mullite whiskers can be used as a reinforcement for polymer-, metal-, and ceramic-matrix composites. The felt can be used as preforms for fabricating composite materials as well as for thermal insulation and high temperature, chemically stable filters for liquids (melts) and gases.

Talmy, Inna G.↗
DOE OSTI2020

Development of Monitoring Techniques for Laser Powder Bed Additive Manufacturing of Metal Structures (Progress Report)

The Transformational Challenge Reactor (TCR) program is leveraging additive manufacturing (AM) technologies to fabricate nuclear grade components to be assembled into a fully functional microreactor core. Compared to traditional manufacturing technologies, additive manufacturing technologies allow (1) observation of the manufacturing process at a much higher resolution in real time using in situ monitoring technologies to capture the sensor signature that scientifically describes each event occurring over time and space, and (2) validation of the manufacturing process quality using domain-informed data analytics techniques as a potential qualification and certification methodology for the final component. This report provides an update on the program work on laser powder bed fusion in-situ process monitoring and associated data analytics results. Examples are provided to illustrate the progress. Elements of the Digital Thread and data management are discussed in the main document, and an extensive supplemental material section is provided detailing the Digital Platform, as well as its implementation and components. In conclusion the path forward for the next fiscal year is discussed.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗