Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “high density”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Ultrasonic Characterization of Lithium Ion Thermal Runaway Conditions for Real-time Ultrasonic Enabled BMS Integration

The demand for energy storage is growing, and lithium-ion batteries are a promising technology to meet this need due to their high power/energy density, high round-trip efficiency, rapid response time, and portability. However, recent catastrophic events caused by thermal runaway have slowed their adoption, highlighting the need for an early warning system for battery failure. In this work, ultrasound is used to detect physical changes in 950 mAh batteries by identifying material property changes independent of voltage and current. [Ultrasound signal features (e.g., time of flight, maximum frequency component) were extracted as the batteries were cycled and subjected to both constant current and constant voltage overcharge and were used to develop two metrics identifying failure: a warning to detect the start of overcharge and an emergency stop (E-stop) to immediately take the battery out of service. The identification method involved locating magnitude differences of several ultrasound features compared to baseline operation considering different currents and temperatures, and the warning/stopping metrics were consistent across all experiments. For an average overcharge time of 140 minutes, the average warning was issued 124 minutes before the failure and the average E-stop was triggered 94 minutes before failure. As a test of using ultrasound for early warning detection, a battery was forced into overcharge and returned to normal cycling conditions based on the previously determined warning metric. Both the voltage profile and the ultrasound measurements returned to their baseline behavior, indicating that ultrasonic detection can not only identify battery failure before a catastrophic event, but can also provide early enough warnings such that overcharges can be detected and corrected quickly enough so the battery does not need to be decommissioned.]

25 ENERGY STORAGE↗
DOE OSTI2023

Solid oxide metal-air redox batteries (SOMARB)

The solid oxide metal-air redox batteries (SOMARB), composed of reversible solid oxide fuel cell (RSOFC) and energy storage unit (ESU), is an emerging technology for large-scale energy storage owing to its advantages in high energy density, high rate capability, decoupled energy and power components, all solid state structure, high safety and scalability. Starting with introducing the working principle of this battery, thermodynamics and kinetics, and battery chemistries based on Fe, Mo, and Wo of SOMARB are illustrated. The strategies to improve the performance of Fe-based SOMARB via optimizing RSOFC and ESU are discussed in detail. Finally, several high temperature metal-air batteries derived from SOMARB are introduced. The comparison with other batteries shows that SOMARB is expected to play an important role in future grid and renewable energy storage with concurrent advances in SOFC stack and system design.

Zhang, Cuijuan↗
DOE OSTI2024

Neural network denoising of x-ray images from high-energy-density experiments

Noise is a consistent problem for x-ray transmission images of High-Energy-Density (HED) experiments because it can significantly affect the accuracy of inferring quantitative physical properties from these images. We consider experiments that use x-ray area backlighting to image a thin layer of opaque material within a physics package to observe its hydrodynamic evolution. The spatial variance of the x-ray transmission across the system due to changing opacity serves as an analog for measuring density in this evolving layer. The noise in these images adds nonphysical variations in measured intensity, which can significantly reduce the accuracy of our inferred densities, particularly at small spatial scales. Denoising these images is thus necessary to improve our quantitative analysis, but any denoising method also affects the underlying information in the image. In this paper, we present a method for denoising HED x-ray images via a deep convolutional neural network model with a modified DenseNet architecture. In our denoising framework, we estimate the noise present in the real (data) images of interest and apply the inferred noise distribution to a set of natural images. These synthetic noisy images are then used to train a neural network model to recognize and remove noise of that character. We show that our trained denoiser network significantly reduces the noise in our experimental images while retaining important physical features.

47 OTHER INSTRUMENTATION↗
DOE OSTI2026

Upcycling mixed cathode materials to high-energy-density LiFe 0.75 Mn 0.25 PO 4

To address the demand for next-generation cathode materials with high energy density, upcycling LiFePO 4 into LiFe 0.75 Mn 0.25 PO 4 has attracted considerable attention. Nevertheless, existing strategies have yet to achieve both morphology and full elemental recovery under mild ambient conditions. Here, we report an upcycling route that can address this issue by combining leaching and a high-temperature treatment process. The upcycled LiFe 0.75 Mn 0.25 PO 4 exhibits enlarged lattice spacing and a high discharge plateau, and it delivers an energy density of 563.7 Wh/kg, 40.3 Wh/kg higher than recycled LiFePO 4 , which indicates the high value of the proposed upcycling strategy. At 1 C, LiFe 0.75 Mn 0.25 PO 4 also exhibits excellent cycling stability of 91% over 700 cycles. Techno-economic analysis also indicates impressive economic and environmental benefits, including 10.4% less raw materials usage and 12.2% less energy consumption and wastewater generation. This work demonstrates a scalable and economic upcycling strategy and provides a promising pathway for sustainable battery upcycling compatible with industrial conditions.

LMFP↗
DOE OSTI2020

Investigation of the neoclassical ambipolar electric field in ion-root plasmas on W7-X

The role of the radial electric field in high-performance ion-root plasmas on Wendelstein 7-X (W7-X) is examined and compared with neoclassical predictions herein. The W7-X stellarator is the world’s first large-scale optimized stellarator. One of the important targets chosen for optimization during the W7-X design process was the reduction of core neoclassical heat transport. This optimization was targeted for reactor-relevant high-density plasmas with $T_e ≈ T_i$ in which the neoclassical ambipolar radial electric field is expected to be negative throughout the plasmas core. Measurements of the core radial electric field $(E_r)$ have confirmed that ion-root conditions (negative $(E_r)$ in the plasma core) have been achieved in W7-X with high-density plasmas and central ECRH. These measured $(E_r)$ profiles agree well with the neoclassical ambipolar $(E_r)$ predicted by the code SFINCS . This good agreement provides confidence in the validity of neoclassical calculations in high-density ion-root conditions, and enables initial studies on the role of neoclassical transport in the optimized high-density regime of W7-X. Profile measurements of electron temperature $(T_e)$, ion temperature $(T_i)$ and electron density $(n_e)$ along with approximations for the average value of $Z$ eff have been used as inputs to the sfincs code to calculate the ambipolar $E_r$ profile along with neoclassical ion and electron energy flux profiles $(Q$ NCi , $Q$ NCe $)$. Finally the total experimental energy input to the plasma from ECRH heating has been compared to the neoclassical energy fluxes to provide a first estimate for the fraction of transport that can be attributed to neoclassical processes in reactorrelevant high-density ion-root conditions.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Metallicity beats sSFR: the connection between superluminous supernova host galaxy environments and the importance of metallicity for their production

ABSTRACT We analyse 33 Type I superluminous supernovae (SLSNe) taken from Zwicky Transient Facility (ZTF)’s Bright Transient Survey to investigate the local environments of their host galaxies. We use a spectroscopic sample of galaxies from the Sloan Digital Sky Survey (SDSS) to determine the large-scale environmental density of the host galaxy. Noting that SLSNe are generally found in galaxies with low stellar masses, high star formation rates (SFRs), and low metallicities, we find that SLSN hosts are also rarely found within high-density environments. Only $3\substack{+9 \\ -1}$ per cent of SLSN hosts were found in regions with two or more bright galaxies within 2 Mpc. For comparison, we generate a sample of 662 SDSS galaxies matched to the photometric properties of the SLSN hosts. This sample is also rarely found within high-density environments, suggesting that galaxies with properties required for SLSN production favour more isolated environments. Furthermore, we select galaxies within the IllustrisTNG simulation to match SLSN host galaxy properties in colour and stellar mass. We find that the fraction of simulated galaxies in high-density environments quantitatively match the observed SLSN hosts only if we restrict to simulated galaxies with metallicity 12 + log (O/H) ≤ 8.12. In contrast, limiting to only the highest specific star formation rate (sSFR) galaxies in the sample leads to an overabundance of SLSN hosts in high-density environments. Thus, our measurement of the environmental density of SLSN host galaxies appears to break the degeneracy between low metallicity and high sSFR as the driver for SLSN hosts and provides evidence that the most constraining factor on SLSN production is low metallicity.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2021

Electrodes with silicon oxide active materials for lithium ion cells achieving high capacity, high energy density and long cycle life performance

Improved negative electrodes can comprise a silicon based active material blended with graphite to provide more stable cycling at high energy densities. In some embodiments, the negative electrodes comprise a blend of polyimide binder mixed with a more elastic polymer binder with a nanoscale carbon conductive additive. The silicon-based blended graphite negative electrodes can be matched with positive electrodes comprising nickel rich lithium nickel manganese cobalt oxides to form high energy density cells with good cycling properties.

Venkatachalam, Subramanian↗
DOE OSTI2023

Electrodes with silicon oxide active materials for lithium ion cells achieving high capacity, high energy density and long cycle life performance

Improved negative electrodes can comprise a silicon based active material blended with graphite to provide more stable cycling at high energy densities. In some embodiments, the negative electrodes comprise a blend of polyimide binder mixed with a more elastic polymer binder with a nanoscale carbon conductive additive. The silicon-based blended graphite negative electrodes can be matched with positive electrodes comprising nickel rich lithium nickel manganese cobalt oxides to form high energy density cells with good cycling properties.

Venkatachalam, Subramanian↗
DOE OSTI2021

A review of thermal physics and management inside lithium-ion batteries for high energy density and fast charging

Traditionally it has been assumed that battery thermal management systems should be designed to maintain the battery temperature around room temperature. That is not always true as lithium-ion battery (LIB) R&D is pivoting towards the development of high energy density and fast charging batteries. Therefore, it is necessary to have a comprehensive review of thermal considerations for LIBs targeted for high energy density and fast charging, i.e., the optimal thermal condition, thermal physics (heat transport and generation) inside the battery, and thermal management strategies. As the energy density and charge rate increases, the optimal battery temperature can shift to be higher than room temperature. In the first part of the review various sources of heat generation inside LIBs and various approaches to minimizing battery heat generation are summarized. The importance of heat of mixing due to ion diffusion during fast charging is also highlighted. To improve the temperature uniformity and avoid excessive internal temperature rise, heat transfer inside the battery needs to be enhanced, and reducing the thermal contact resistance between the electrodes and separator can significantly increase the effective thermal conductivity of batteries. In the second part of the review various challenges and latest developments related to thermal transport and properties of LIBs are discussed. Finally, a summary of latest advancement on smart control of internal temperature of LIBs is discussed as depending on the ambient temperature and the optimal temperature; the battery heat needs to be retained or dissipated to elevate or avoid temperature rise.

25 ENERGY STORAGE↗
DOE OSTI2025

Development of Li–S Battery Cells with High Energy Density and Long Cycling Life

Lithium–sulfur (Li–S) batteries are considered one of the most promising next-generation energy storage technologies for electric vehicles, owing to their high energy density (up to three times greater than current lithium-ion batteries) and the low cost of sulfur (approximately 100 times cheaper than conventional cobalt oxide). However, several challenges hinder their commercial viability, including the electronically and ionically insulating nature of sulfur, polysulfide dissolution, and lithium dendrite growth. These issues significantly limit battery energy density and cycle life and must be addressed to enable successful commercialization. Current strategies involving porous carbon structures, additives, and electrocatalyst engineering have not fully resolved the polysulfide dissolution problem. While polysulfide-free cathode materials offer a promising solution, they often suffer from low sulfur content, leading to reduced discharge capacity and sluggish reaction kinetics. To overcome these limitations, we have developed novel soluble-polysulfide-free sulfur cathode active materials with a high sulfur content (>50 wt%). By integrating these cathodes with functional binders, optimized electrolyte formulations, and refined electrode fabrication techniques, we demonstrate Li–S batteries with both high energy density and long cycle life. This advancement brings the realization of low-cost, high-energy Li–S batteries significantly closer to practical application.

25 ENERGY STORAGE↗
DOE OSTI2024

Studies of High Energy Density Discharge and Laser-Driven Deflagrating Plasma Stagnations

The goal of this proposal is to develop an understanding of the thermalization and mixing of high energy density (HED) interpenetrating and stagnating plasma deflagrations on two different platforms. The first is opposing gas-fed Z-pinch plasma expansions in a facility at Stanford University. The second is the convergence of multiple deflagration fronts generated by inverted corona laser ablations through experiments carried out by the P.I. as part of a larger team at the University of Rochester Laboratory for Laser Energetics. The link between the two platforms is the role played by kinetic effects that impact mixing and the conversion of directed to thermal energy. Such kinetic effects are important because of the relatively high temperatures despite high plasma densities.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

PISCES-RF: a liquid-cooled high-power steady-state helicon plasma device

Radio-frequency (RF) driven helicon plasma sources can produce relatively high-density plasmas (n > 1019 m -3 ) at relatively moderate powers (<2 kW) in argon. However, to produce similar high-density plasmas for fusion relevant gases such as hydrogen (H), deuterium (D) and helium (He), much higher RF powers are needed. For very high RF powers, thermal issues of the RF-transparent dielectric window, used in the RF source design, limit the plasma operation timescales. To mitigate this constraint, we have designed, built and tested a novel helicon plasma source assembly with a fully liquid-cooled RF-transparent window which allows steady state operations at high power (up to 20 kW) and successfully produces high-density plasma with both argon and H. Deionized (DI) water, flowing between two concentric dielectric RF windows, is used as the coolant. We show that a full azimuthal blanket of DI water does not prevent high-density plasma production. From calorimetry on the DI water, we measure the net heat removed by the coolant at steady state conditions. Using infra-red imaging, we calculate the constant plasma heat deposition and measure the final steady state temperature distribution patterns on the inner surface of the ceramic layer. The heat deposition pattern follows the helical shape of the antenna. We also show the consistency between the heat absorbed by the DI water, as measured by calorimetry, and the total heat due to the combined effect of the plasma heating and the absorbed RF. These results are being used to answer critical engineering questions for the 200 kW RF device materials plasma exposure experiment being designed at the Oak Ridge National Laboratory as a next generation plasma material interaction device.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Measurement of interfacial thermal resistance in high-energy-density matter

Heat transport across interfaces is a ubiquitous phenomenon with many unresolved aspects. In particular, it is unknown if an interfacial thermal resistance (ITR) occurs in matter with high-energy-density where free electrons dominate the heat conduction. Here, we report on the first experimental evidence that a significant heat barrier is present between two different regions of high-energy-density matter: a strongly heated tungsten wire and a surrounding plastic layer that stays relatively cold. We use diffraction-enhanced imaging to track the time evolution of density discontinuities and reconstruct the temperature evolution in the quasi-stationary stage. The clear signatures of a temperature jump demonstrate the importance of the ITR for strongly heated systems with far-reaching implications for interpreting experiments and applications like inertial confinement fusion.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

On the study of hydrodynamic instabilities in the presence of background magnetic fields in high-energy-density plasmas

Blast-wave-driven hydrodynamic instabilities are studied in the presence of a background B-field through experiments and simulations in the high-energy-density (HED) physics regime. In experiments conducted at the Laboratoire pour l’utilisation des lasers intenses (LULI), a laser-driven shock-tube platform was used to generate a hydrodynamically unstable interface with a prescribed sinusoidal surface perturbation, and short-pulse x-ray radiography was used to characterize the instability growth with and without a 10-T B-field. The LULI experiments were modeled in FLASH using resistive and ideal magnetohydrodynamics (MHD), and comparing the experiments and simulations suggests that the Spitzer model implemented in FLASH is necessary and sufficient for modeling these planar systems. These results suggest insufficient amplification of the seed B-field, due to resistive diffusion, to alter the hydrodynamic behavior. Although the ideal-MHD simulations did not represent the experiments accurately, they suggest that similar HED systems with dynamic plasma-β (=2μ0ρv2/B2) values of less than ∼100 can reduce the growth of blast-wave-driven Rayleigh–Taylor instabilities. These findings validate the resistive-MHD FLASH modeling that is being used to design future experiments for studying B-field effects in HED plasmas.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Revisiting Discharge Mechanism of CF x as a High Energy Density Cathode Material for Lithium Primary Battery

Lithium/fluorinated graphite (Li/CFx) primary batteries show great promise for applications in a wide range of energy storage systems due to their high energy density (>2100 Wh kg –1 ) and low self-discharge rate (<0.5% per year at 25 °C). While the electrochemical performance of the CF x cathode is indeed promising, the discharge reaction mechanism is not thoroughly understood to date. In this article, a multiscale investigation of the CF x discharge mechanism is performed using a novel cathode structure to minimize the carbon and fluorine additives for precise cathode characterizations. Titration gas chromatography, X-ray diffraction, Raman spectroscopy, X-ray photoelectron spectroscopy, scanning electron microscopy, cross-sectional focused ion beam, high-resolution transmission electron microscopy, and scanning transmission electron microscopy with electron energy loss spectroscopy are utilized to investigate this system. Results show no metallic lithium deposition or intercalation during the discharge reaction. Crystalline lithium fluoride particles uniformly distributed with <10 nm sizes into the CF x layers, and carbon with lower sp2 content similar to the hard-carbon structure are the products during discharge. This article deepens the understanding of CF x as a high energy density cathode material and highlights the need for future investigations on primary battery materials to advance performance.

25 ENERGY STORAGE↗
DOE OSTI2025

Development and characterization of a laser-gated, high resolution x-ray radiography platform for high energy density experiments using toroidally bent crystals

Bent crystal x-ray imagers are a well-established diagnostic tool to study high energy density (HED) objects by acquiring two-dimensional x-ray radiographs. Often, studying these HED objects requires very high spatial resolution, which is limited by astigmatism when using spherically bent crystals. By using toroidal-shaped crystals instead, astigmatism can be reduced and the overall spatial resolution of the instrument improved. Here, the development and characterization of a laser-gated x-ray radiography platform at the National Ignition Facility using a toroidal crystal is presented. This includes measurements of the spatial and temporal profile, which is determined by the x-ray source. In conclusion, to properly validate the reduced astigmatism, a new multi-plane grid approach was implemented, which, for the first time, allows a depth of field measurement, alignment verification and x-ray source size estimate in a single shot, demonstrating the current platform’s capability to provide sub-10 μm resolution over a 0.9 mm depth of field with a temporal resolution of 110 ps.

Crystal optics↗
DOE OSTI2023

Low Impedance Cathode/Electrolyte Interfaces for High Energy Density Solid-State Batteries

All-solid-state batteries (ASSBs) using a ceramic fast Li-ion conductor as a solid-state electrolyte (SSE) have been proposed as a promising strategy to significantly increase the energy density of lithium batteries. Due to their high ion conductivity and excellent stability, Li-stuffed garnets exhibit the most promising physical and chemical properties for SSEs. However, the typical microstructure, thick (>100 μm) bulk electrolyte and simple planar electrode/electrolyte interfaces, combined with poor electrode wetting of the garnet result in excessively high area specific resistances (ASRs) that severely limit achievable current density and cell energy density. In this project, the team is building on their demonstrated expertise with garnet electrolytes and ASSBs to accomplish the following: (1) engineer interfaces to overcome high NMC/LLZ interfacial impedance and interfacial degradation; (2) develop processing and fabrication techniques to achieve high loading NMC/LLZ composite cathodes with low resistance and high cyclability; and (3) integrate the NMC/LLZ cathodes into all-solid-state Li-metal/LLZ cells to achieve high-energy-density batteries.

25 ENERGY STORAGE↗
DOE OSTI2025

Strontium-84 Enrichments in Presolar Grains Provide First Evidence of p -process Nucleosynthesis in Core-collapse Supernovae

This study reports detection of rare p-process isotopes within presolar grains. Presolar grains are relic dust grains from dying stars. These microscopic dust particles are found in primitive solar system materials. Their distinct isotopic compositions record the nucleosynthetic processes in their parent stars and the Galactic chemical environment in which these stars formed. We studied presolar graphite grains of high-density type from the Murchison meteorite and found five grains with subgrains that show enrichments in 84 Sr compared to the solar abundance. 84 Sr is the neutron-deficient isotope of strontium that can be produced in the deep oxygen-rich interior of high-mass stars that end their lives as core-collapse supernovae. The observed 84 Sr excesses cannot be produced in low-mass asymptotic giant branch stars, the source of most high-density presolar graphites found in meteorites. High-density graphites with embedded 84 Sr excesses are, instead, compatible with a core-collapse supernovae origin. The graphite subgrains condensed from carbon-rich materials in the outer layers of core-collapse supernovae, where 84 Sr was destroyed by neutron captures during hydrostatic evolution of the stars and their final explosion. Based on current theoretical stellar models, a few percent of contribution from the inner regions of core-collapse supernovae, which are enriched in p-process nuclides, to the outer carbon-rich regions is the most likely explanation for the observed enrichment of 84 Sr in the subgrains of the high-density graphites. In this study, we present the first observational evidence that core-collapse supernovae produce and eject isotopes made by the p-process.

Astronomy and AstroPhysics↗