SEARCH · Engineering Papers

Results for “heat engines”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17

All sources NASA NTRS DOE OSTI

NASA NTRS1981

Steam Rankine Solar Receiver, phase 2

A steam rankine solar receiver (SRSR) based on a tubular concept was designed and developed. The SRSR is an insulated, cylindrical coiled tube boiler which is mounted at the focal plane of a fully tracking parabolic solar reflector. The concentrated solar energy received at the focal plane is then transformed to thermal energy through steam generation. The steam is used in a small Rankine cycle heat engine to drive a generator for the production of electrical energy. The SRSR was designed to have a dual mode capability, performing as a once through boiler with and without reheat. This was achieved by means of two coils which constitute the boiler. The boiler core size of the SRSR is 17.0 inches in diameter and 21.5 inches long. The tube size is 7/16 inch I.D. by 0.070 inch wall for the primary, and 3/4 inch I.D. by 0.125 inch wall for the reheat section. The materials used were corrosion resistant steel (CRES) type 321 and type 347 stainless steel. The core is insulated with 6 inches of cerablanket insulation wrapped around the outer wall. The aperture end and the reflector back plate at the closed end section are made of silicon carbide. The SRSR accepts 85 kwth and has a design life of 10,000 hrs when producing steam at 1400 F and 2550 psig.

Deanda, L. E.↗

NASA NTRS1981

Air Brayton Solar Receiver, phase 2

An air Brayton solar receiver (ABSR) is discussed. The ABSR consists of a cylindrical, insulated, offset plate fin heat exchanger which is mounted at the focal plane of a fully tracking parabolic solar collector. The receiver transfer heat from the concentrated solar radiation (which impinges on the inside walls of the heat exchanger) to the working fluid i.e., air. The hot air would then e used to drive a small Brayton cycle heat engine. The engine in turn drives a generator which produces electrical energy. Symmetrical and asymmetrical solar power input into the ABSR are analyzed. The symmetrical cases involve the baseline incident flux and the axially shifted incident fluxes. The asymmetrical cases correspond to the solar fluxes that are obtained by reduced solar input from one half of the concentrator or by receiver offset of plus or minus 1 inch from the concentrator optical axis.

Deanda, L. E.↗

NASA NTRS1981

The effect of concentrator field layout on the EE-1 small community solar power system

The point-focusing distributed receiver (PFDR) concept is employed by a number of solar thermal power systems currently under development. One type of PFDR system which shows particular promise incorporates distributed energy generation. According to this concept each parabolic dish collector is a self-contained power generation module, and a conventional electrical system is used to interconnect the modules. The concept is thus modular, and any number of power modules can be combined to achieve the required plant size. Given the benefits of mass production, it appears that this type of system can produce electricity at lower cost than is projected for conventional (fossil) power systems over the next decade. An employment of organic Rankine cycle heat engines is considered.

Pons, R. L.↗

NASA NTRS1983

Advanced Vehicle system concepts

Various nonpetroleum vehicle system concepts for passenger vehicles in the 1990's are being considered as part of the Advanced Vehicle (AV) Assessment at the Jet Propulsion Laboratory. The vehicle system and subsystem performance requirements, the projected characteristics of mature subsystem candidates, and promising systems are presented. The system candidates include electric and hybrid vehicles powered by electricity with or without a nonpetroleum power source. The subsystem candidates include batteries (aqueous-mobile, flow, high-temperature, and metal-air), fuel cells (phosphoric acid, advanced acids, and solid polymer electrolyte), nonpetroleum heat engines, advanced dc and ac propulsion components, power-peaking devices, and transmissions.

Hardy, K. S.↗

NASA NTRS1983

Improved performance thermal barrier coatings

Thermal barrier coatings offer an attractive approach to improving the durability and efficiency of the hot section of heat engines. The coatings typically consist of an inner alloy bond coating about 0.01 cm thick resistant to oxidation and hot corrosion and an outer ceramic layer, usually a stabilized zirconia, 0.01-0.05 cm thick. Here, the materials, thermomechanical stress, and hot corrosion problems associated with thermal barrier coatings are reviewed along with the capabilities and limitations of current technology. The coatings discussed include ZrO2-Y2O3/NiCrAlY, ZrO2-Y2O3/NiCoCrAlY, ZrO2-MgO/NiCoCrAlY, CaO-SiO2/Co-Cr-Al-Y, and CaO-SiO2/NiCrAlY systems. It is emphasized that the performance of thermal barrier coatings is governed by many complex and interrelated factors, so that optimization of these coatings always involves certain tradeoffs.

Levine, S. R.↗

NASA NTRS1983

Ceramics potential in automotive powerplants

The paper addresses the potential that ceramic materials can play an important role in future automotive powerplants - both advanced heat engines and advanced battery systems. A number of related experimental programs are reviewed including ceramics for gasoline and diesel piston engines, gas turbine and Stirling Engines and sodium-sulfur batteries. A strong integrated program to develop ceramics technology is recommended.

Mclean, A. F.↗

NASA NTRS1983

Energy conversion for megawatt space power systems

Large nuclear space power systems capable of continuously producing over one megawatt of electrical power for a several year period will be needed in the future. This paper presents the results of a study to compare applicable conversion technologies which were deemed to be ready for a time period of 1995 and beyond. A total of six different conversion technologies were studied in detail and compared on the basis of conversion efficiency, radiator area, overall system mass, and feasibility. Three static, modular conversion technologies were considered; these include: AMTEC, thermionic, and thermoelectric conversion. The other three conversion technologies are heat engines which involve dynamic components. The dynamic systems analyzed were Brayton, Rankine, and the free piston Stirling engine. Each of the conversion techniques was also examined for limiting characteristics and an attempt was made to identify common research needs and enabling technologies.

Ewell, R.↗

NASA NTRS1984

The effect of concentrator field layout on the performance of point-focus distributed receiver systems

The effect of concentrator field layout on the technical-economic performance of a point-focusing distributed receiver (PFDR) solar thermal power plant is presented. The plant design is based on the small community prototype system currently under development for JPL/DOE; parabolic dish concentrators are employed, and small heat engines are used to generate electricity at each dish. The effect of field size, array proportions, dish-to-dish spacing and packing fraction (concentrator-land area ratio) are presented for typical PFDR layouts. Economic analyses are carried out to determine optimum packing fraction as a function of site cost.

Pons, R. L.↗

NASA NTRS1985

Magnetic field generation in the cores of terrestrial bodies

Efforts to find some scaling law for the dipole moments of planets seem illusory for, although dynamo theory is still in a rudimentary state, once the critical magnetic Reynolds Number is exceeded it appears that the field strength is determined by the energy source, it it is permissible to treat the core as a heat engine. For this reason the lunar magnetic field is of special significance as the paleomagnetic evidence strongly suggests that the surface field was about 1 G 3.9 by diminishing exponentially to about .02 G 3.2 by ago and completely disappearing some time later.

Runcorn, S. K.↗

NASA NTRS1986

Space Station momentum control and reboost requirements for two power generation concepts

Results are presented of dynamic structural analyses of 75 and 300 kW versions of a solar dynamic (SD) power supply for the Space Station (MSS). The SD is being seriously considered as an alternative to solar panels due to lower areal and mass requirements and higher efficiencies. The functioning principle is to use parabolic concentrators to focus sunlight on a heat engine to boil liquids to drive a turbine. Potential problems are foreseen in terms of the torques which would be experienced by the MSS and the subsequent orbital stability effects. The stability would be altered by changing aerodynmaic drag, altered moment of inertia and angular momentum and the altered center of mass location. The problem is exacerbated by the need to first equip the MSS with solar panels while the SD technology is developed. The analysis shows that the attitude control system will need to be redesigned and resized to accommodate MSS growth with either power system. The effects of the rotating parts of the SD system can be minimized, but further studies are required to determine the effects on the pointing accuracy of the SD, which must be 10 times as precise as that needed by a photovoltaic array.

Farmer, J. T.↗

NASA NTRS1985

Sintered alpha silicon carbide ceramics for high temperature structural application - Status review and recent developments

The physical properties of sintered alpha silicon carbide are reviewed, including the effect of oxidation at high temperatures. Net shape fabricated components are described which have undergone extensive testing in heat engine applications. Properties of an SiC/TiB2 composite material, which has significantly improved fracture toughness, are presented.

Storm, R. S.↗

NASA NTRS1986

Hybrid deployable/erectable solar dynamic box truss system

The design of a hybrid deployable/erectable solar dynamic box truss power generation system for the initial operation capability (IOC) of the Space Shuttle is examined. An organic Rankine cycle heat engine for IOC solar power generation is studied. The design configuration is a simple parabolic concentration where the receiver is located in the focal plane with its aperture at the focal point. The relationship between concentrator size and collection efficiency is analyzed. The geometry of the deployable graphite/epoxy box truss ring and the reflective panels of the system are described. Mass properties and dynamic analyses are performed to evaluate the center of gravity location and moments of inertia characteristics of the energy conversion subsystem (ECS). The deployable/erectable truss is applicable for large IR space telescopes and center and offset fed ECSs.

Coyner, J. V., Jr.↗

NASA NTRS1987

More Efficient Solar Thermal-Energy Receiver

Thermal stresses and reradiation reduced. Improved design for solar thermal-energy receiver overcomes three major deficiencies of solar dynamic receivers described in literature. Concentrator and receiver part of solar-thermal-energy system. Receiver divided into radiation section and storage section. Concentrated solar radiation falls on boiling ends of heat pipes, which transmit heat to thermal-energy-storage medium. Receiver used in number of applications to produce thermal energy directly for use or to store thermal energy for subsequent use in heat engine.

Dustin, M. O.↗

NASA NTRS1987

Heat-Exchanger/Heat-Pipe Interface

Monolithic assembly reliable and light in weight. Heat exchanger and evaporator ends of heat pipes integrated in monolithic halves welded together. Interface assembly connects heat exchanger of furnace, reactor, or other power source with heat pipes carrying heat to radiator or power-consuming system. One of several concepts proposed for nuclear power supplies aboard spacecraft, interface useful on Earth in solar thermal power systems, heat engines, and lightweight cooling systems.

Snyder, H. J.↗

NASA NTRS1987

Increased Accuracy in Ultrasonic Material Characterization

Improvements in ultrasonic measuring technology obtained. Used in variety of ways, to include: Determination of ultrasonic attenuation and velocity in heat-engine ceramics and advanced metals; verification of accuracy of ultrasonic measurements; and real-time in situ ultrasonic monitoring of microstructural changes. Technology interests producers and fabricators of metals and ceramics for aerospace and other critical applications.

Generazio, Edward R.↗

NASA NTRS1987

Making a Silicon-Nitride/Silicon-Carbide Composite

Hot pressing and nitriding produce strong fiber/matrix material. Fabrication method developed for processing strong and tough silicon-based ceramic composite material, SiC/RBSN, which consists of reaction-bonded Si3N4 (RBSN) reinforced by continuous-length, high-modulus, high strength silicon carbide (SiC) fibers prepared by chemical-vapor deposition method. Increased toughness and ultimate strength of SiC/RBSN composite makes it potential structural material for advanced heat engines.

Bhatt, R. T.↗

NASA NTRS1987

Carbide/Fluoride/Silver Self-Lubricating Composite

Bearing coatings survive at operating temperatures up to 870 degrees C. PS200 composite self-lubricating coating for bearing applications operating at temperatures above failure points of traditional solid lubricants. Excellent friction and wear performance in oxidizing atmospheres up to 1,600 degrees F and reducing atmospheres up to 1,400 degrees F. Performance needed for development of advanced heat engines as adiabatic diesel and Stirling engine.

Sliney, Harold E.↗

NASA NTRS1987

FORTRAN Algorithm for Image Processing

FORTRAN computer algorithm containing various image-processing analysis and enhancement functions developed. Algorithm developed specifically to process images of developmental heat-engine materials obtained with sophisticated nondestructive evaluation instruments. Applications of program include scientific, industrial, and biomedical imaging for studies of flaws in materials, analyses of steel and ores, and pathology.

Roth, Don J.↗