Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “geometric modelling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
NASA NTRS1990

Advanced recovery systems wind tunnel test report

Pioneer Aerospace Corporation (PAC) conducted parafoil wind tunnel testing in the NASA-Ames 80 by 120 test sections of the National Full-Scale Aerodynamic Complex, Moffett Field, CA. The investigation was conducted to determine the aerodynamic characteristics of two scale ram air wings in support of air drop testing and full scale development of Advanced Recovery Systems for the Next Generation Space Transportation System. Two models were tested during this investigation. Both the primary test article, a 1/9 geometric scale model with wing area of 1200 square feet and secondary test article, a 1/36 geometric scale model with wing area of 300 square feet, had an aspect ratio of 3. The test results show that both models were statically stable about a model reference point at angles of attack from 2 to 10 degrees. The maximum lift-drag ratio varied between 2.9 and 2.4 for increasing wing loading.

Geiger, R. H.↗
NASA NTRS1974

Geometrical geodesy techniques in Goddard earth models

The method for combining geometrical data with satellite dynamical and gravimetry data for the solution of geopotential and station location parameters is discussed. Geometrical tracking data (simultaneous events) from the global network of BC-4 stations are currently being processed in a solution that will greatly enhance of geodetic world system of stations. Previously the stations in Goddard earth models have been derived only from dynamical tracking data. A linear regression model is formulated from combining the data, based upon the statistical technique of weighted least squares. Reduced normal equations, independent of satellite and instrumental parameters, are derived for the solution of the geodetic parameters. Exterior standards for the evaluation of the solution and for the scale of the earth's figure are discussed.

Lerch, F. J.↗
NASA NTRS1987

Geometric versus finite element modeling current and future trends at Northrop

Engineering Automation at Northrop encompasses the various design and analytical phases of air vehicle development. Design systems addresses automation of engineering/tooling design and computer aided manufacturing processes. The analysis systems automate aeroelastic modeling and postprocessing analysis results. These systems interface with aircraft loft and geometric entities thru localized transfer techniques. However, total integration effort based on a geometric database nucleus with peripheral design, analytical and manufacturing systems is well underway. An outline of the present and future trends is presented to help channel the RPI effort in this direction.

Bajaj, Shiv K.↗
NASA NTRS2013

Automated 3D Damaged Cavity Model Builder for Lower Surface Acreage Tile on Orbiter

The 3D Automated Thermal Tool for Damaged Acreage Tile Math Model builder was developed to perform quickly and accurately 3D thermal analyses on damaged lower surface acreage tiles and structures beneath the damaged locations on a Space Shuttle Orbiter. The 3D model builder created both TRASYS geometric math models (GMMs) and SINDA thermal math models (TMMs) to simulate an idealized damaged cavity in the damaged tile(s). The GMMs are processed in TRASYS to generate radiation conductors between the surfaces in the cavity. The radiation conductors are inserted into the TMMs, which are processed in SINDA to generate temperature histories for all of the nodes on each layer of the TMM. The invention allows a thermal analyst to create quickly and accurately a 3D model of a damaged lower surface tile on the orbiter. The 3D model builder can generate a GMM and the correspond ing TMM in one or two minutes, with the damaged cavity included in the tile material. A separate program creates a configuration file, which would take a couple of minutes to edit. This configuration file is read by the model builder program to determine the location of the damage, the correct tile type, tile thickness, structure thickness, and SIP thickness of the damage, so that the model builder program can build an accurate model at the specified location. Once the models are built, they are processed by the TRASYS and SINDA.

Belknap, Shannon↗
NASA NTRS1992

Geometric-optical bidirectional reflectance modeling of the discrete crown vegetation canopy - Effect of crown shape and mutual shadowing

Many natural vegetation covers can be regarded as assemblages of plant crowns, on a background, which interact with light as discrete objects. On this basis, geometric optics furnish an approach to the modeling of vegetation canopies that captures the most important features of such growths' bidirectional measurements. Attention is presently given to models which approximate these phenomena and relate the size, shape, and count density of plant crowns to viewing and illumination positions and to crown-background reflectance contrasts.

Li, Xiaowen↗
NASA NTRS2014

Update on Linear Mode Photon Counting with the HgCdTe Linear Mode Avalanche Photodiode

The behavior of the gain-voltage characteristic of the mid-wavelength infrared cutoff HgCdTe linear mode avalanche photodiode (e-APD) is discussed both experimentally and theoretically as a function of the width of the multiplication region. Data are shown that demonstrate a strong dependence of the gain at a given bias voltage on the width of the n− gain region. Geometrical and fundamental theoretical models are examined to explain this behavior. The geometrical model takes into account the gain-dependent optical fill factor of the cylindrical APD. The theoretical model is based on the ballistic ionization model being developed for the HgCdTe APD. It is concluded that the fundamental theoretical explanation is the dominant effect. A model is developed that combines both the geometrical and fundamental effects. The model also takes into account the effect of the varying multiplication width in the low bias region of the gain-voltage curve. It is concluded that the lower than expected gain seen in the first 2 × 8 HgCdTe linear mode photon counting APD arrays, and higher excess noise factor, was very likely due to the larger than typical multiplication region length in the photon counting APD pixel design. The implications of these effects on device photon counting performance are discussed.

HgCdTe↗
NASA NTRS2019

Camera modeling, centroiding performance, and geometric camera calibration on ASTERIA

The Arcsecond Space Telescope Enabling Research in Astrophysics (ASTERIA) is a 10-kg, 6U CubeSat in low-Earth orbit that was able to achieve subarcsecond pointing stability and repeatability. To date, this is the best pointing on a spacecraft of its size. This paper will analyze various aspects of the performance of its key piece of hardware—the payload. First,a model of the optics and imager, which is used to simulate stellar images, will be presented. The imager parameters used in this model were derived from simple ground measurements. Next, a centroiding algorithm is provided and used on the simulated images to predict centroiding performance. These results will be shown to match on-orbit telemetry of centroiding performance, validating the modeling approach. This paper will then describe an approach for and results of a geometric camera calibration algorithm to estimate the focal length,distortion,and alignment parameters. The modeling, analyses, and results presented in this paper provide key information that can be used in a time domain pointing simulation or a frequency-domain pointing error analysis.

Smith, Matthew W.↗
NASA NTRS2018

Considerations When Building Thermal Models that Require Conversion Between Formats

At times, it is inevitable to require conversion of thermal models from one software format to another. This most often occurs for missions with international partners where not all parties utilize the same software packages for thermal analysis. Mandating a single tool for all parties is one possible solution, but this approach can introduce problems if significant effort is required to overcome inexperience with the designated tool and may result in difficulty meeting analysis schedule requirements. Alternatively, allowing all parties to use their own familiar tools minimizes the impact to analysis schedules but does introduce the need to convert the models later to a common format for analysis at a higher level of assembly. External conversion tools and formats have been developed through the years to aid in this process, but have had limited success in fully converting models seamlessly. Having a basic familiarity with tool capabilities on both sides of the conversion process allows for models to be built in a manner to better facilitate conversion by avoiding features and capabilities which are unsupported by the destination tool or for which no workarounds exist. Also, the effort to convert a model is often neglected when developing the schedules for analysis at the higher assembly levels; delivery of models preconditioned for convertibility minimizes the schedule risk. This paper seeks to provide some guidance on modeling techniques to avoid when developing Geometrical Math Models (GMM) and Thermal Math Models (TMM) when conversion is required. The recommendations are based on GMM conversion experiences between TSS/ThermalDesktop/ESARAD and TMM conversions between SINDA-FLUINT/ESATAN.

Modeling↗
NASA NTRSDate not supplied

An Investigation of the Dragonfly Mission Aeroshell/Parachute Dynamics through Subscale Drop Tests

The Dragonfly mission will place a rotorcraft/lander on Titan by 2034. The entry, descent, and landing system of the Dragonfly mission includes two parachutes: a drogue and a main. To provide needed data, subscale drop tests were used to conduct an experimental investigation of the aeroshell/parachute dynamics. The drop tests used a Disk-Gap-Band drogue parachute and two types of Ringslot main parachutes. All tests used a representative aeroshell which included the heatshield. All models were geometrically scaled to 16.7 percent. The model aeroshell had a diameter of 0.75 m. The model parachute nominal diameters were 0.9 m for the drogue and 2.78 m for the main. The aeroshell’s mass properties were dynamically scaled to simulate flight at an altitude of 4 km at Titan. This dynamic scaling allowed the conversion of model test results to full-scale Titan conditions. Onboard instrumentation on the aeroshell provided data on the rotation rates, from which the Euler angles were determined. Tests were conducted by lifting the models with a drone to an altitude of 350 m and dropping them inverted. Key results from these tests were: 1) the models were able to recover from the extreme inverted initial condition and settle to low-amplitude oscillations; 2) ninety nine percent of the time the oscillation amplitudes observed with the drogue parachute were 11.4 degrees or less; 3) ninety nine percent of the time the oscillation amplitudes observed with the 20 percent porosity main parachute were 15.4 degrees or less.

Parachutes↗
NASA NTRSDate not supplied

An Investigation of the Dragonfly Mission Aeroshell/Parachute Dynamics through Subscale Drop Tests

The Dragonfly mission will place a rotorcraft/lander on Titan by 2034. The entry, descent, and landing system of the Dragonfly mission includes two parachutes: a drogue and a main. To provide needed data, subscale drop tests were used to conduct an experimental investigation of the aeroshell/parachute dynamics. The drop tests used a Disk-Gap-Band drogue parachute and two types of Ringslot main parachutes. All tests used a representative aeroshell which included the heatshield. All models were geometrically scaled to 16.7 percent. The model aeroshell had a diameter of 0.75 m. The model parachute nominal diameters were 0.9 m for the drogue and 2.78 m for the main. The aeroshell’s mass properties were dynamically scaled to simulate flight at an altitude of 4 km at Titan. This dynamic scaling allowed the conversion of model test results to full-scale Titan conditions. Onboard instrumentation on the aeroshell provided data on the rotation rates, from which the Euler angles were determined. Tests were conducted by lifting the models with a drone to an altitude of 350 m and dropping them inverted. Key results from these tests were: 1) the models were able to recover from the extreme inverted initial condition and settle to low-amplitude oscillations; 2) ninety nine percent of the time the oscillation amplitudes observed with the drogue parachute were 11.4 degrees or less; 3) ninety nine percent of the time the oscillation amplitudes observed with the 20 percent porosity main parachute were 15.4 degrees or less.

Parachutes↗
NASA NTRS1989

AutoCAD-To-NASTRAN Translator Program

Program facilitates creation of finite-element mathematical models from geometric entities. AutoCAD to NASTRAN translator (ACTON) computer program developed to facilitate quick generation of small finite-element mathematical models for use with NASTRAN finite-element modeling program. Reads geometric data of drawing from Data Exchange File (DXF) used in AutoCAD and other PC-based drafting programs. Written in Microsoft Quick-Basic (Version 2.0).

Jones, A.↗
NASA NTRS2000

Modeling and Characterization of Geometric Effects on the Performance of Rainbow and Thunder Actuators

Dome formation in Rainbow and Thunder actuators occurs to relieve thermal expansion mismatch stress between the metallic and piezoelectric layers during cooling from device fabrication temperatures. Accompanying this process is the generation of an internal stress profile within the devices and the development of significant tensile stresses within the surface region of the piezoelectric. These tensile stresses affect the domain configuration (ratio of c-to-a domains), and improve the 90 deg. domain wall movement response of the device in this region of the piezoelectric. This results in improved electromechanical performance compared to standard direct extensional and flextensional devices, presumably because of the contributions of stress to the non-linearity of the piezoelectric d-coefficients. 1 Interestingly, this improvement in response seems counterintuitive; a stress perpendicular to the direction of the applied electric field should impede, not contribute to 90' domain switching. Further consideration of the lower region of the piezoelectric that is under compressive stress thus appears warranted. The specified objectives of the research were to: 1. Conduct finite element and equivalent circuit simulation-based investigations to understand the effects of actuator geometry on internal stress distribution and actuator performance (displacement and load-bearing capabilities). 2. Use the results of the modeling studies to predict the processing conditions (geometry and thickness ratio) required for the fabrication of Rainbow ceramics with optimized performance.

Schwartz, Robert W.↗
NASA NTRS1975

Interactive computer aided technology, evolution in the design/manufacturing process

A powerful computer-operated three dimensional graphic system and associated auxiliary computer equipment used in advanced design, production design, and manufacturing was described. This system has made these activities more productive than when using older and more conventional methods to design and build aerospace vehicles. With the use of this graphic system, designers are now able to define parts using a wide variety of geometric entities, define parts as fully surface 3-dimensional models as well as "wire-frame" models. Once geometrically defined, the designer is able to take section cuts of the surfaced model and automatically determine all of the section properties of the planar cut, lightpen detect all of the surface patches and automatically determine the volume and weight of the part. Further, his designs are defined mathematically at a degree of accuracy never before achievable.

English, C. H.↗
NASA NTRS1992

Exhaust plumes and their interaction with missile airframes - A new viewpoint

The present, novel treatment of missile airframe-exhaust plume interactions emphasizes their simulation via a formal solution of the Reynolds-averaged Navier-Stokes (RNS) equation and is accordingly able to address the simulation requirements of novel missiles with nonconventional/integrated propulsion systems. The method is made possible by implicit RNS codes with improved artificial dissipation models, generalized geometric capabilities, and improved two-equation turbulence models, as well as by such codes' recent incorporation of plume thermochemistry and multiphase flow effects.

Dash, S. M.↗
NASA NTRS1992

The application of a geometric optical canopy reflectance model to semiarid shrub vegetation

Estimates are obtained of the average plant size and density of shrub vegetation on the basis of SPOT High Resolution Visible Multispectral imagery from Chihuahuan desert areas, using the Li and Strahler (1985) model. The aggregated predictions for a number of stands within a class were accurate to within one or two standard errors of the observed average value. Accuracy was highest for those classes of vegetation where the nonrandom scrub pattern was characterized for the class on the basis of the average coefficient of the determination of density.

Franklin, Janet↗
NASA NTRS1993

Thermomechanical postbuckling analysis of laminated composite shells

The nonlinear response of laminated composite structures subjected to thermal loads is investigated. Analysis is performed using a refined theory and an associated finite element model for geometrically nonlinear analysis of laminated composite shell structures. The model is based on a third-order displacement field which accounts for both transverse shear and transverse normal deformations. Numerical studies of simply-supported plates and cylindrical panels indicate that when the panels are free to expand or contract in the transverse direction, the predicted critical buckling temperatures do not depend significantly upon whether or not transverse normal deformations are explicitly accounted for in the analysis model. However, the critical buckling temperatures are strongly dependent upon whether or not the transverse normal deformations are restrained along the boundaries of the panels.

Averill, R. C.↗