Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “femtosecond dynamics”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Aggregation‐Induced Stimulated Emission of 100% Dye Microspheres

Dyes with aggregation-induced emission (AIE) properties have gained interest due to their bright luminescence in solid-state aggregates. While fluorescence from AIE dyes is widely exploited, relatively little is known about aggregation-induced stimulated emission. Here, stimulated emission of tetraphenylethene (TPE)-based organoboron AIE dyes, TPEQBN, in thin films and in microcavity lasers is investigated. Using femtosecond pump–probe spectroscopy, gain coefficients up to 230 cm -1 at 500 nm are measured. Using rate equations, concentration- and pump-dependent gain dynamics as well as laser build-up dynamics are analyzed. During laser oscillation, radiative stimulated emission allows high instantaneous quantum yield greater than 90% to be achieved. Solid-state microspheres made of 100% AIE dyes are fabricated via microfluidic emulsion and solvent evaporation method. Coupled with high gain and high refractive index of 1.76, microspheres as small as 2 µm in diameter show lasing by nanosecond pumping with a threshold of ≈10 pJ µm –2 . Polymer coated, but not bare, microspheres are internalized by live cells and generate narrowband cavity-mode emission from within the cytoplasm. This work shows the potential of AIE dyes as laser materials.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Detection of coherent optical phonons in a thin bismuth film by ultrafast electron diffraction

Coherent dynamics of lattice oscillations in a ∼20-nm-thick film obtained by thermal sputtering of bismuth is studied using ultrashort electron bunches synchronised with femtosecond laser pulses irradiating the sample. The Fourier analysis of ultrafast electron diffraction (UED) data shows that the observed modulation of the signal is due to the ensemble of modes corresponding to optical phonons with frequencies of approximately 3, 6 and 9 THz. A conclusion is made that these peaks correspond to the manifestation of the bismuth A{sub 1g} mode (three-terahertz peak), as well as its first and second overtones, which is probably due to quantum confinement in a 20-nm Bi nanostructure. The possibility of a detailed study of the quantum-size effect in bismuth with the help of a transmission UED is analysed. (paper)

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2021

Eisenbud–Wigner–Smith time delay in atom–laser interactions

We report recent development of ultrafast measurement techniques on the sub-femtosecond time scale has enabled us to see the atom–laser interaction in real time. One of the important observables to study the temporally resolved dynamics is the various time delay in the process. Time delays is an experimentally measurable quantity, where the time is not. Time delays in quantum collisions and in photoionization/photodetachment of atomic and molecular systems is reviewed. The formalisms of time delay in the context of quantum collisions by Eisenbud and Wigner that by Smith and their equivalence is discussed. The time-reversal symmetry between solutions with outgoing and ingoing wave boundary conditions allow us to interpret photoionization/photodetachment as half-scattering. Subsequently, the formalism of Eisenbud–Wigner–Smith time delay is extended in photoionization/photodetachment from collisions. We discuss that the time delay can be written as a self-adjoint quantum operator which depicts its measurability. On the experimental side, the measurement protocols are reviewed for attosecond streaking and RABBITT. Along with the EWS time delay, the measurement introduces an additional (which is negative) time delay. From the measurement of total delay and an analytical/numerical estimate of the measurement induced part, one gets the EWS time delay in the process. A few illustrative examples of studies on time delay are given to get a flavour of the outstanding advances made in this field in the last two decades.

74 ATOMIC AND MOLECULAR PHYSICS↗
DOE OSTI2021

Vibronic Coupling and Exciton Chirality: Electronic and Structural Rearrangement between Helical to Zero Momentum Molecular Exciton States

Helical porphyrin aggregates are attractive macromolecular nanostructures for biomimetic light-harvesting and energy transfer in solar energy technology due to their large light absorbing cross sections and promising energy conservation benefits from chiral-induced spin selectivity. However, with these soft materials, it is imperative that we understand how the nuclear degrees of freedom impact the excitonic energy landscape and dynamics, particularly pertaining to how it influences the chiral angular momentum of the excitons. To this end, we have measured time-resolved depolarization ratios using femtosecond stimulated Raman spectroscopy to uncover the vibronic coupling guided by molecular vibrations between excitons of different angular momentum in helical tetra(sulfonatophenyl)porphyrin aggregates. We find that while transient absorption anisotropy reveals rapid (1 ps lifetime) exciton rotation from helical to achiral states in the Q-band, time-resolved vibrational depolarization ratios evolve on remarkably faster time scales (<500 fs lifetime) for the totally symmetric 1530 cm –1 vibration and the nontotally symmetric 1540 cm –1 vibration. The time-resolved depolarization ratios of the 1540 cm –1 vibration, in particular, show strong evidence of vibronic coupling and nonadiabatic exciton behavior that mediates the nonradiative transition between chiral and achiral excitons. Furthermore, our study shows that for rational design of helical molecular aggregates for exciton transport, the vibronic coupling between excitons of different angular momenta driven by molecular vibrations must be considered especially in the case where chiral-induced spin selectivity is desired.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Precision-controlled ultrafast electron microscope platforms. A case study: Multiple-order coherent phonon dynamics in 1T-TaSe2 probed at 50 fs–10 fm scales

We report on the first detailed beam tests attesting the fundamental principle behind the development of high-current-efficiency ultrafast electron microscope systems where a radio frequency (RF) cavity is incorporated as a condenser lens in the beam delivery system. To allow for the experiment to be carried out with a sufficient resolution to probe the performance at the emittance floor, a new cascade loop RF controller system is developed to reduce the RF noise floor. Temporal resolution at 50 fs in full-width-at-half-maximum and detection sensitivity better than 1% are demonstrated on exfoliated 1T-TaSe2 system under a moderate repetition rate. To benchmark the performance, multi-terahertz edge-mode coherent phonon excitation is employed as the standard candle. The high temporal resolution and the significant visibility to very low dynamical contrast in diffraction signals via high-precision phase-space manipulation give strong support to the working principle for the new high-brightness femtosecond electron microscope systems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Optically induced changes in the band structure of the Weyl charge-density-wave compound (TaSe 4 ) 2 I

Collective modes are responsible for the emergence of novel quantum phases in topological materials. In the quasi-one dimensional (1D) Weyl semimetal (TaSe 4 ) 2 I , a charge density wave (CDW) opens band gaps at the Weyl points, thus turning the system into an axionic insulator. Melting the CDW would restore the Weyl phase, but 1D fluctuations extend the gapped regime far above the 3D transition temperature (T CDW = 263 K), thus preventing the investigation of this topological phase transition with conventional spectroscopic methods. Here we use a non-equilibrium approach: we perturb the CDW phase by photoexcitation, and we monitor the dynamical evolution of the band structure by time- and angle-resolved photoelectron spectroscopy. We find that, upon optical excitation, electrons populate the linearly dispersing states at the Fermi level (E F ), and fill the CDW gap. The dynamics of both the charge carrier population and the band gap renormalization (BGR) show a fast component with a characteristic time scale of a few hundreds femtoseconds. However, the BGR also exhibits a second slow component on the µs time scale. The combination of an ultrafast response and of persistent changes in the spectral weight at E$_\mathrm{F}$, and the resulting sensitivity of the linearly dispersing states to optical excitations, may explain the high performances of (TaSe 4 ) 2 I as a material for broadband infrared photodetectors.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Vortex-Controlled Quasiparticle Multiplication and Self-Growth Dynamics in Superconducting Resonators

Even in the quantum limit, non-equilibrium quasiparticle (QP) populations induce QP poisoning that irreversibly relaxes the quantum state and significantly degrades the coherence of transmon qubits. A particularly detrimental yet previously unexplored mechanism arises from QP multiplication facilitated by vortex trapping in superconducting quantum circuits, where a high-energy QP relaxes by breaking additional Cooper pairs and amplifying the QP population due to the locally reduced excitation gap and enhanced quantum confinement within the vortex core. Here we directly resolve this elusive QP multiplication process by revealing vortex-controlled QP self-generation in a highly nonequilibrium regime preceding the phonon bottleneck of QP relaxation. At sufficiently low fluence, femtosecond-resolved magneto-reflection spectroscopy directly reveals a continuously increasing QP population that is strongly dependent on magnetic-field-tuned vortex density and absent at higher excitation fluences. Quantitative analysis of the emergent QP pre-bottleneck dynamics further reveals that, although the phonon population saturates within $\simeq$10~ps, both free and trapped QPs continue to grow in a self-sustained manner--hallmarks of the long-anticipated QP-vortex interactions in nonequilibrium superconductivity. We estimate a substantial increase of $\sim$34% in QP density at vortex densities of $\sim$ 100 magnetic flux quanta per $\mathrm{μm^{2}}$. Our findings establish a powerful spectroscopic tool for uncovering QP multiplication and reveal vortex-assisted QP relaxation as a critical materials bottleneck whose mitigation will be essential for resolving QP poisoning and enhancing coherence in superconducting qubits.

Park, Joong M. [Ames Lab]↗
DOE OSTI2020

Preventing Bio-Bloopers and XFEL Follies: Best Practices from your Friendly Instrument Staff

Serial Femtosecond Crystallography (SFX) at X-ray Free electron Lasers (XFELs) is a relatively new field promising to deliver unparalleled spatial and temporal resolution on biological systems and there dynamics. Over the past decade, though, there have been a handful of results that have truly delivered on these promises. Why? SFX has many paradigm shifting techniques not seen in typical structural biology arenas, such as creating a concentrated slurry of microcrystals rather than a handful of loopable prisms worthy of a catalog photo. Then taking that slurry and high speed jetting them towards the vacuum or helium interation region to destroy less than 1% of your sample and waste the other 99. The literature is full of techniques and methods promising to cure what ails your experiment, yet as an instrument scientist will tell you –and a first author might admit after a few drinks at the conference happy hour—is that there are a lot more failures than the success we published, results may vary. We will walk through a best practices on how to prepare your sample and chose a sample delivery technique that will amerliorate your studies rather than undermine your hardwork and hopefully lead to better experimental planning and execution, inching you closer to that scientific goal and that call from Stockholm. This will be written in a more editorialized fashion and is meant to give the reader an idea of what to try or how they should be thinking. Welcome to SFX, now what?

47 OTHER INSTRUMENTATION↗
DOE OSTI2024

Time-resolved Auger–Meitner spectroscopy of the photodissociation dynamics of CS 2

The photodissociation dynamics of UV excited CS 2 are investigated using time-resolved Auger–Meitner (AM) spectroscopy. AM decay is initiated by inner-shell ionisation with a femtosecond duration x-ray (179.9 eV) probe generated by the FERMI free electron laser. The time-delayed x-ray probe removes an electron from the S(2p) orbital leading to secondary emission of a high energy electron through AM decay. We monitor the electron kinetic energy of the AM emission as a function of pump-probe delay and observe time-dependent changes in the spectrum that correlate with the formation of bound, excited-state CS 2 molecules at early times, and CS + S fragments on the picosecond timescale. The results are analysed based on a simplified kinetic scheme that provides a time constant for dissociation of approximately 1.2 ps, in agreement with previous time-resolved x-ray photoelectron spectroscopy measurements (Gabalski, et al 2023 J. Phys. Chem. Lett. 14 7126–7133).

Auger spectroscopy↗
NASA NTRS2018

Tandem LA-ICP-MS & LIBS; A New Micro-Analytical Technique for the Measurement of Every Element in the Periodic Table

Laser Ablation ICP-MS (LA-ICP-MS) has been widely accepted as a microanalytical technique for in-situ trace (ppb) elemental analysis on the micron scale in a variety of geologic materials. LA-ICP-MS (single or multi-collector) provides both elemental and isotopic measurements critical for a wide range of geological research by generating a fine grained aerosol (nm scale) during the laser ablation event and delivering that aerosol to the ICP ion source of the mass spectrometer via an inert carrier gas. LA-ICP-MS, however, suffers from limitations in analyzing high ionization potential elements as well as elements subject to atmospheric and argon based interferences. LA-ICP-MS also has limitations in analyzing major elements due to detector saturation. An alternative laser ablation technique, Laser Induced Breakdown Spectroscopy (LIBS), employs an optical spectrometer integrated into the laser ablation system that analyzes the laser induced plasma at the sample surface across the entire optical spectrum for emission lines of every element in the periodic table. Elements that are difficult or impossible to measure with LA-ICP-MS are now possible to analyze with LIBS down to low ppm levels with CCD and/or ICCD detection. We introduce a new laser based technique, “Tandem LA-LIBS”, that combines LA for ICP-MS and LIBS into one integrated laser ablation system. This system has the effect of expanding the elemental coverage and the dynamic range of the laser ablation experiment as measurements from ppb to % level matrix elements can now be analyzed in a single ablation experiment. We present both femtosecond and nanosecond Tandem LA-LIBS quantitative and qualitative data on wide range of geological materials for those elements that are difficult or impossible by traditional LA-ICP-MS techniques such as F, H, O, N, C, S, halogens, etc. We also demonstrate that the simultaneous measurement of trace, minor and major elements are now possible in a single laser ablation experiment with Tandem LA-LIBS technology.

LA-ICP-MS↗
DOE OSTI2021

Observation and Control of Unidirectional Ballistic Dynamics of Nanoparticles at a Liquid–Gas Interface by 4D Electron Microscopy

Understanding and controlling the dynamics of active Brownian objects far from equilibrium are fundamentally important for emerging technologies such as artificial micro/nanomotors for drug deliveries and noninvasive microsurgery. However, direct observation and control of unidirectional propulsion of individual nanoscale objects are technically challenging due to the required spatiotemporal resolution. Here, we report in situ visualization and manipulation of unidirectional superfast ballistic dynamics of a single-photon-activated gold nanoparticle (NP) along the liquid–gas interface by four-dimensional electron microscopy (4D EM) at nanometer and nanosecond scales. We observed that, upon repetitive femtosecond laser excitation, the NP at the liquid–gas interface exhibits a continuously superfast unidirectional translation with a linear dependence of its root mean squared velocity (νrms) on either the laser fluence or repetition rate. Under a single femtosecond pulse excitation, the NP exhibits a superfast ballistic translation at the nanosecond time scale. Combined experiment and physical modeling reveals that the superfast unidirectional, ballistic translation is driven by unidirectional random impulsive forces arising from the nanobubbles (NBs) induced by enhanced laser heating as a result of plasmonic excitation, which is controllable by tuning the laser characteristics. Furthermore, this directional plasmonic NB-propulsion mechanism sheds light on the design of light-controllable artificially intelligent micro/nanomotor systems.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2022

Full 3D Kinetic Modeling and Quantification of Positive Streamer Evolution in an Azimuthally Swept Pin-to-Plane Wedge Geometry

Cathode-directed streamer evolution in near atmospheric air is modeled in 3D pin-to-plane geometries using a 3D kinetic Particle-In-Cell (PIC) code that simulates particle-particle collisions via the Direct Simulation Monte Carlo (DSMC) method. Due to the computational challenges associated with a complete 360° volumetric domain, a practical alternative was achieved using a wedge domain and a range of azimuthal angles was explored (5°, 15°, 30°, and 45°) to study possible effects on the streamer growth and propagation due to the finite wedge angle. A DC voltage of 6 kV is administered to a hemispherical anode of radius 100 μm, with a planar cathode held at ground potential, generating an over-volted state with an electric field of 4 MV/m across a 1500 μm gap. The domain is seeded with an initial ion and electron density of 10 18 m -3 at 1 eV temperature confined to a spherical region of radius 100 μm centered at the tip of the anode. The air chemistry model [1] includes standard Townsend breakdown mechanisms (electron-neutral elastic, excitation, ionization, attachment, and detachment collision chemistry and secondary electron emission) as well as streamer mechanisms (photoionization and ion-neutral collisions) via tracking excited state neutrals which can then either quench via collisions or spontaneously emit a photon based on specific Einstein-A coefficients [2, 3]. In this work, positive streamer dynamics are formally quantified for each wedge angle in terms of electron velocity and density as temporal functions of coordinates r, Φ, and z. Applying a random plasma seed for each simulation, particles of interest are tracked with near femtosecond temporal resolution out to 1.4 ns and spatially binned. This process is repeated six times and results are averaged. Prior 2D studies have shown that the reduced electric field, E/n, can significantly impact streamer evolution [4]. We extend the analysis to 3D wedge geometries, to limit computational costs, and examine the wedge angle’s effect on streamer branching, propagation, and velocity. Results indicate that the smallest wedge angle that produced an acceptably converged solution is 30°. The potential effects that a mesh, when under-resolved with respect to the Debye length, can impart on streamer dynamics and numerical heating were not investigated, and we explicitly state here that the smallest cell size was approximately 10 times the minimum λ D in the streamer channel at late times. This constraint on cell size was the result of computational limitations on total mesh count.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2024

Attosecond Probing of Coherent Vibrational Dynamics in CBr 4

A coherent vibrational wavepacket is launched and manipulated in the symmetric stretch (a1) mode of CBr 4 , by impulsive stimulated Raman scattering (ISRS) from nonresonant 400 nm laser pump pulses with various peak intensities on the order of tens of 10 12 W/cm 2 . Extreme ultraviolet (XUV) attosecond transient absorption spectroscopy (ATAS) records the wavepacket dynamics as temporal oscillations in XUV absorption energy at the bromine M 4,5 3d 3/2,5/2 edges around 70 eV. The results are augmented by nuclear timedependent Schrödinger equation simulations. Slopes of the (Br 3d 3/2,5/2 ) –1 10a 1 * core-excited state potential energy surface (PES) along the a 1 mode are calculated to be –9.4 eV/Å from restricted open-shell Kohn–Sham calculations. Using analytical relations derived for the small-displacement limit and the calculated slopes of the core-excited state PES, a deeper insight into the vibrational dynamics is obtained by retrieving the experimental excursion amplitude of the vibrational wavepacket and the amount of population transferred to the vibrational first-excited state as a function of pump-pulse peak intensity. Experimentally, the results show that XUV ATAS is capable of resolving oscillations in the XUV absorption energy on the order of a few to tens of meV with tens of femtosecond time precision. This corresponds to change in C–Br bond length on the order of 10 –4 to 10 –3 Å. The results and the analytic relationships offer a clear physical picture, on multiple levels of understanding, of how the pump-pulse peak intensity controls the vibrational dynamics launched by nonresonant ISRS in the small-displacement limit.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Ultrafast low-temperature metal–insulator interface phonon dynamics and heat transport in a Pt/Gd 3 Fe 5 O 12 heterostructure

Interfacial thermal and acoustic phenomena have an important role in quantum science and technology, including in spintronic and spincaloritronic materials and devices. Simultaneous measurements of the low-temperature thermal and acoustic properties of a metal/insulator heterostructure reveal distinct dynamics in the characteristic phonon frequency ranges of acoustic and thermal transport. The measurements probed a heterostructure consisting of a thin film of Pt on the ferrimagnetic insulator gadolinium iron garnet (Gd 3 Fe 5 O 12 , GdIG) grown epitaxially on a gadolinium gallium garnet substrate. Ultrafast structural dynamics within the Pt layer were tracked using time-resolved ultrafast x-ray diffraction and analyzed to probe interfacial acoustic and thermal properties. The rapid heating of the Pt layer by a 400 nm wavelength femtosecond-duration optical pulse produced transient structural changes that provided the stimulus for these measurements. Rapid heating produced a broadband acoustic pulse that was partially reflected by the Pt/GdIG interface. Temporal frequencies up to 740 GHz, corresponding to angular frequencies of several THz, were detected in a wavelet analysis of the acoustic oscillations of the strain in the Pt layer. The structural results were analyzed to determine (i) the acoustic damping coefficient and phonon mean free path in Pt at frequencies of hundreds of GHz and (ii) the Grüneisen anharmonicity parameter. The thermal conductance of the Pt/GdIG interface was tracked using the slower, tens-of-picosecond-scale, dynamics of the initial cooling of the heated Pt layer. Analysis using a model based on the Boltzmann transport equation shows that the phonon transmission is lower at the phonon frequencies relevant to thermal transport than for subterahertz regime acoustics.

Acoustic phenomena↗
DOE OSTI2021

Visualization of dynamic polaronic strain fields in hybrid lead halide perovskites

Excitation localization involving dynamic nanoscale distortions is a central aspect of photocatalysis, quantum materials and molecular optoelectronics. Experimental characterization of such distortions requires techniques sensitive to the formation of point-defect-like local structural rearrangements in real time. Here, we visualize excitation-induced strain fields in a prototypical member of the lead halide perovskites via femtosecond resolution diffuse X-ray scattering measurements. Here, this enables momentum-resolved phonon spectroscopy of the locally distorted structure and reveals radially expanding nanometre-scale strain fields associated with the formation and relaxation of polarons in photoexcited perovskites. Quantitative estimates of the magnitude and shape of this polaronic distortion are obtained, providing direct insights into the dynamic structural distortions that occur in these materials. Optical pump–probe reflection spectroscopy corroborates these results and shows how these large polaronic distortions transiently modify the carrier effective mass, providing a unified picture of the coupled structural and electronic dynamics that underlie the optoelectronic functionality of the hybrid perovskites.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Ultrafast Dynamics of Excited Electronic States in Nitrobenzene Measured by Ultrafast Transient Polarization Spectroscopy

We investigate ultrafast dynamics of the lowest singlet excited electronic state in liquid nitrobenzene using ultrafast transient polarization spectroscopy, extending the well-known technique of optical Kerr effect spectroscopy to excited electronic states. The third-order nonlinear response of the excited molecular ensemble is measured using a pair of femtosecond pulses following a third femtosecond pulse that populates the S 1 excited state. By measuring this response, which is highly sensitive to details of the excited state character and structure, as a function of time delays between the three pulses involved, we extract the dephasing time of the wave packet on the excited state. The dephasing time, measured as a function of time delay after pump excitation, shows oscillations indicating oscillatory wave packet dynamics on the excited state. Finally, from the experimental measurements and supporting theoretical calculations, we deduce that the wave packet completely leaves the S 1 state potential energy surface after three traversals of the intersystem crossing between the singlet S 1 and triplet T 2 states.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Ultrafast visualization of incipient plasticity in dynamically compressed matter

Plasticity is ubiquitous and plays a critical role in material deformation and damage; it inherently involves the atomistic length scale and picosecond time scale. A fundamental understanding of the elastic-plastic deformation transition, in particular, incipient plasticity, has been a grand challenge in high-pressure and high-strain-rate environments, impeded largely by experimental limitations on spatial and temporal resolution. Here, we report femtosecond MeV electron diffraction measurements visualizing the three-dimensional (3D) response of single-crystal aluminum to the ultrafast laser-induced compression. We capture lattice transitioning from a purely elastic to a plastically relaxed state within 5 ps, after reaching an elastic limit of ~25 GPa. Our results allow the direct determination of dislocation nucleation and transport that constitute the underlying defect kinetics of incipient plasticity. Large-scale molecular dynamics simulations show good agreement with the experiment and provide an atomic-level description of the dislocation-mediated plasticity.

36 MATERIALS SCIENCE↗
DOE OSTI2021

The interplay between laser focusing conditions, expansion dynamics, ablation mechanisms, and emission intensity in ultrafast laser-produced plasmas

The interplay between ultrafast laser focusing conditions, emission intensity, expansion dynamics, and ablation mechanisms is critical to the detection of light isotopes relevant to nuclear energy, forensics, and geochemistry applications. Here, we study deuterium (2Hα) emission in plasmas generated from femtosecond laser ablation of a Zircaloy-4 target with a deuterium concentration of ≈37 at. %. Changes in emission intensity, plume morphology, crater dimensions, and surface modifications were investigated for varying focusing lens positions, where the laser was focused behind, at, and in front of the target. Spatially resolved optical emission spectroscopy and spectrally integrated plasma imaging were performed to investigate emission spectral features and plume morphology. Laser ablation crater dimensions and morphology were analyzed via optical profilometry and scanning electron microscopy. The 2Hα emission intensity showed significant reduction at the geometrical focal point or when the focal point is in front of the target. For all laser spot sizes, a two-component plume was observed but with different temporal histories. At the best focal point, the plume was spherical. When the laser was focused behind the target, the plume was elongated and propagated to farther distances than for the best focal position. In contrast, when the laser was focused in front of the target, filaments were generated in the beam path, and filament-plasma coupling occurred. By focusing the laser behind the target, the amount of material removal in the laser ablation process can be significantly reduced while still generating a plasma with a sufficient 2Hα emission signal for analysis.

Kautz, Elizabeth J. (ORCID:0000000263389223)↗