Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “digitized waveform”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17

Precise Interval Timer for Software Defined Radio

A precise digital fractional interval timer for software defined radios which vary their waveform on a packet-by-packet basis. The timer allows for variable length in the preamble of the RF packet and allows to adjust boundaries of the TDMA (Time Division Multiple Access) Slots of the receiver of an SDR based on the reception of the RF packet of interest.

Pozhidaev, Aleksey↗

A highly capable arbitrary waveform generator for next generation radar systems

We are developing an Arbitrary Waveform Generator (AWG) to provide enhanced capability for radar applications. The current design will accommodate two waveform generators on a single unit for dual frequency operation. The basic architecture of this unit employs a Field Programmable Gate Array (FPGA) and a high speed and high precision Digital to Analog Converter (DAC) for direct digital synthesis. This AWG will be capable of up to 450 MHz bandwidth with ability for frequency notching. Phase fidelity of less than 1.2(sup o) deviation RMS is also achievable. This AWG operates with lower power consumption as compared with other waveform generators, which is advantageous for future spaceborne applications. This will enable radars to return higher precision data, to be reduced in complexity, and to operate in any band without interfering with dedicated bandwidths.

chirp generators↗

the P-wave upper mantle structure beneath an active spreading center: The Gulf of California

Detailed analysis of short period travel time, and waveform data reveals the upper mantle structure beneath an oceanic ridge to depths of 900 km. More than 1400 digital seismograms from earthquakes in Mexico and central America recorded at SCARLET yield 1753 travel times and 58 direct measurements of short period travel time as well as high quality, stable waveforms. The 29 events combine to form a continuous record section from 9 deg to 40 deg with an average station spacing of less than 5 km. First the travel times are inverted. Further constraints arise from the observed relative amplitudes of mantle phases, which are modeled by trial and error.

Walck, M. C.↗

Multi-axis transient vibration testing of space objects: Test philosophy, test facility, and control strategy

IABG has been using various servohydraulic test facilities for many years for the reproduction of service loads and environmental loads on all kinds of test objects. For more than 15 years, a multi-axis vibration test facility has been under service, originally designed for earthquake simulation but being upgraded to the demands of space testing. First tests with the DFS/STM showed good reproduction accuracy and demonstrated the feasibility of transient vibration testing of space objects on a multi-axis hydraulic shaker. An approach to structural qualification is possible by using this test philosophy. It will be outlined and its obvious advantages over the state-of-the-art single-axis test will be demonstrated by example results. The new test technique has some special requirements to the test facility exceeding those of earthquake testing. Most important is the high reproduction accuracy demanded for a sophisticated control system. The state-of-the-art approach of analog closed-loop control circuits for each actuator combined with a static decoupling network and an off-line iterative waveform control is not able to meet all the demands. Therefore, the future over-all control system is implemented as hierarchical full digital closed-loop system on a highly parallel transputer network. The innermost layer is the digital actuator controller, the second one is the MDOF-control of the table movement. The outermost layer would be the off-line iterative waveform control, which is dedicated only to deal with the interaction of test table and test object or non-linear effects. The outline of the system will be presented.

Lachenmayr, Georg↗

Digital transmitter for data bus communications system

Digital transmitter designed for Manchester coded signals (and all signals with ac waveforms) generated at a rate of one megabit per second includes efficient output isolation circuit. Transmitter consists of logic control section, amplifier, and output isolation section. Output isolation circuit provides dynamic impedance at terminals as function of amplifier output level.

Proch, G. E.↗

A fast-reacting and versatile optokinetic stimulus pattern by computer graphics with application examples

A computer graphics method for the generation of horizontally moving vertical stripes which serve as stimuli for optokinetic nystagmus is presented. The pattern is generated by the successive addition of a constant in a digital register, leading to its periodic overflow. Digital to analog conversion of the register contents results in a staircase waveform, which is converted into a pattern of vertical lines on a CRT. The addition of any number to the reference buffer shifts all lines uniformly, so that the group velocity of the pattern is easily controlled. The computer controlled display allows an accurate realization of a commanded velocity profile with practically no time delay and facilitates study under conditions of variable feedback. The display software can be easily modified to limit stimulation to a selected area of the moving retina, and the method has been used to simulate central scotomata. It is pointed out that the technique, while more accurate, versatile and responsive than a rotating drum device, may be less useful in experiments requiring a wide field display.

Yasui, S.↗

Space station integrated wall design and penetration damage control. Task 4: Impact detection/location system

A program to develop a methodology is documented for detecting and locating meteoroid and debris impacts and penetrations of a wall configuration currently specified for use on space station. Testing consisted of penetrating and non-penetrating hypervelocity impacts on single and dual plate test configurations, including a prototype 1.22 m x 2.44 m x 3.56 mm (4 ft x 8 ft x 0.140 in) aluminum waffle grid backwall with multilayer insulation and a 0.063-in shield. Acoustic data were gathered with transducers and associated data acquisition systems and stored for later analysis with a multichannel digitizer. Preliminary analysis of test data included sensor evaluation, impact repeatability, first waveform arrival, and Fourier spectral analysis.

Nelson, J. M.↗

The IceCube Collaboration:contributions to the 30 th International Cosmic Ray Conference (ICRC 2007),

This paper bundles 40 contributions by the IceCube collaboration that were submitted to the 30th International Cosmic Ray Conference ICRC 2007. The articles cover studies on cosmic rays and atmospheric neutrinos, searches for non-localized, extraterrestrial {nu}{sub e}, {nu}{sub {mu}} and {nu}{sub {tau}} signals, scans for steady and intermittent neutrino point sources, searches for dark matter candidates, magnetic monopoles and other exotic particles, improvements in analysis techniques, as well as future detector extensions. The IceCube observatory will be finalized in 2011 to form a cubic-kilometer ice-Cherenkov detector at the location of the geographic South Pole. At the present state of construction, IceCube consists of 52 paired IceTop surface tanks and 22 IceCube strings with a total of 1426 Digital Optical Modules deployed at depths up to 2350 m. The observatory also integrates the 19 string AMANDA subdetector, that was completed in 2000 and extends IceCube's reach to lower energies. Before the deployment of IceTop, cosmic air showers were registered with the 30 station SPASE-2 surface array. IceCube's low noise Digital Optical Modules are very reliable, show a uniform response and record waveforms of arriving photons that are resolvable with nanosecond precision over a large dynamic range. Data acquisition, reconstruction and simulation software are running in production mode and the analyses, profiting from the improved data quality and increased overall sensitivity, are well under way.

79 ASTRONOMY AND ASTROPHYSICS↗

Amplitude calibration of spaceborne synthetic aperture radars

Problems encountered during attempts to calibrate SAR imagery, recent successful experiments conducted with SEASAT SAR data, and a proposed program for the calibration and validation of the radar imagery from the forthcoming SIR-B SAR are discussed. The SEASAT SAR data for 10 passes over Death valley, California, were processed with a modified digital correlator. The procedure included a preliminary screening of the data to check for raw data saturation, compensation of waveforms and estimation of the amplitude of the pilot tone. All data was normalized to this pilot tone signal to reduce the effects of variable gains in the data links and ground receivers. The digital correlation algorithm generated image data. Evaluation of 6 passes results in a maximum pass to pass gain variation of only 1.1 dB and a standard deviation amongst the passes of 0.35 dB.

Held, D. N.↗

Amplitude calibration of spaceborne synthetic aperture radars

Problems encountered during attempts to calibrate SAR imagery, recent successful experiments conducted with SEASAT SAR data, and a proposed program for the calibration and validation of the radar imagery from the forthcoming SIR-B SAR are discussed. The SEASAT SAR data for 10 passes over Death Valley, California, were processed with a modified digital correlator. The procedure included a preliminary screening of the data to check for raw data saturation, compensation of waveforms and estimation of the amplitude of the pilot tone. All data was normalized to this pilot tone signal to reduce the effects of variable gains in the data links and ground receivers. The digital correlation algorithm generated image data. Evaluation of 6 passes results in a maximum pass to pass gain variation of only 1.1 dB and a standard deviation amongst the passes of 0.35 dB. previously announced in STAR as N83-26215

Held, D. N.↗

622-Mbps Orthogonal Frequency Division Multiplexing (OFDM) Digital Modem Implemented

Future generation space communications systems feature significantly higher data rates and relatively smaller frequency spectrum allocations than systems currently deployed. This requires the application of bandwidth- and power-efficient signal transmission techniques. There are a number of approaches to implementing such techniques, including analog, digital, mixed-signal, single-channel, or multichannel systems. In general, the digital implementations offer more advantages; however, a fully digital implementation is very difficult because of the very high clock speeds required. Multichannel techniques are used to reduce the sampling rate. One such technique, multicarrier modulation, divides the data into a number of low-rate channels that are stacked in frequency. Orthogonal frequency division multiplexing (OFDM), a form of multicarrier modulation, is being proposed for numerous systems, including mobile wireless and digital subscriber link communication systems. In response to this challenge, NASA Glenn Research Center's Communication Technology Division has developed an OFDM digital modem (modulator and demodulator) with an aggregate information throughput of 622 Mbps. The basic OFDM waveform is constructed by dividing an incoming data stream into four channels, each using either 16- ary quadrature amplitude modulation (16-QAM) or 8-phase shift keying (8-PSK). An efficient implementation for an OFDM architecture is being achieved using the combination of a discrete Fourier transform (DFT) at the transmitter to digitally stack the individual carriers, inverse DFT at the receiver to perform the frequency translations, and a polyphase filter to facilitate the pulse shaping.

Kifle, Muli↗

Challenges and Opportunities in Turning Large U.S. Archives of Analog Seismograms into a Modern Usable Resource

Abstract Quantitative seismology is based firmly on the analysis of actual ground motions, and the transition to digital recording in the 1980s enabled sophisticated new capabilities to extract useful results from waveforms. With some effort, these tools can also be applied to analog records. Focusing on assets available within U.S. institutions, we review the necessary steps and the challenges in enabling “data rescue”—that is, preserving the scientific information latent in large analog seismogram archives and making it usable. They include: determining what assets are available (the analog seismogram archives held by various institutions, with associated metadata on instrument responses, station locations, and timing information); developing a consensus on the top level of a triage process (which analog records most definitely should be rescued?); deciding the level of quality needed in copying original seismograms to media suitable for digitizing; assessing the relative merits of scanning and digitizing; and, the need for a community service in distributing scans and digital records, as they accumulate. The necessary level of effort can benefit from practical experience. For example, specific studies have used digitized versions of analog recordings to model earthquake sources and assess seismic hazard. Other studies have used them to gain experience with nuclear explosion signals recorded at regional distances, noting that regional signals enable explosions to be monitored down to levels much lower than those attainable teleseismically. The opportunities presented by large archives of analog seismograms include the insights they present to current and future seismologists studying earthquakes and explosions, into the practical areas of assessing seismic hazard, monitoring for test ban compliance down to low explosion yields—and prompt characterization of actual explosions should they occur, as well the traditional academic pursuit of a better understanding of earthquake physics.

Geochemistry & Geophysics↗

Digital pile-up rejection for plutonium experiments with solution-grown stilbene

A solution-grown stilbene detector was used in several experiments with plutonium samples including plutonium oxide, mixed oxide, and plutonium metal samples. Neutrons from different reactions and plutonium isotopes are accompanied by numerous gamma rays especially by the 59-keV gamma ray of 241Am. Identifying neutrons correctly is important for nuclear nonproliferation applications and makes neutron/gamma discrimination and pile-up rejection necessary. Each experimental dataset is presented with and without pile-up filtering using a previously developed algorithm. The experiments were simulated using MCNPX-PoliMi, a Monte Carlo code designed to accurately model scintillation detector response. Collision output from MCNPX-PoliMi was processed using the specialized MPPost post-processing code to convert neutron energy depositions event-by-event into light pulses. The model was compared to experimental data after pulse-shape discrimination identified waveforms as gamma ray or neutron interactions. We show that the use of the digital pile-up rejection algorithm allows for accurate neutron counting with stilbene to within 2% even when not using lead shielding

Bourne, M. M.↗

Multi-Modulator for Bandwidth-Efficient Communication

A modulator circuit board has recently been developed to be used in conjunction with a vector modulator to generate any of a large number of modulations for bandwidth-efficient radio transmission of digital data signals at rates than can exceed 100 Mb/s. The modulations include quadrature phaseshift keying (QPSK), offset quadrature phase-shift keying (OQPSK), Gaussian minimum-shift keying (GMSK), and octonary phase-shift keying (8PSK) with square-root raised-cosine pulse shaping. The figure is a greatly simplified block diagram showing the relationship between the modulator board and the rest of the transmitter. The role of the modulator board is to encode the incoming data stream and to shape the resulting pulses, which are fed as inputs to the vector modulator. The combination of encoding and pulse shaping in a given application is chosen to maximize the bandwidth efficiency. The modulator board includes gallium arsenide serial-to-parallel converters at its input end. A complementary metal oxide/semiconductor (CMOS) field-programmable gate array (FPGA) performs the coding and modulation computations and utilizes parallel processing in doing so. The results of the parallel computation are combined and converted to pulse waveforms by use of gallium arsenide parallel-to-serial converters integrated with digital-to-analog converters. Without changing the hardware, one can configure the modulator to produce any of the designed combinations of coding and modulation by loading the appropriate bit configuration file into the FPGA.

Gray, Andrew↗

Determining velocity of detonation using high-resolution time domain reflectometry

Two methods are presented to make measurements of the length of a coaxial cable with submillimeter and submicrosecond accuracy. If the cable is destroyed by the passage of a strong shock, for instance, from the detonation of an explosive, a measure of the phase velocity of the detonation (VOD) can be obtained with high accuracy (≈0.25%). The first method introduces a series of short Gaussian electrical pulses (<300 ps) into the cable that reflect off the cable end and are compared to the time of the original outgoing pulse by using a fast digitizer (100 gigasamples per second). By curve fitting a Gaussian form to the outgoing and reflected pulses, a measurement of the cable length can be made with subsample accuracy. So, as long as the pulses do not overlap, a large number may be present in the cable at any time allowing pulse repetition rates of 40–135 MHz depending on the cable length. Averaging allows accurate VOD measurements to be made that are comparable with the best traditional techniques. The second method replaces the pulser with a wide-spectrum (0.1–10 GHz) amplified random noise source. A similar setup and digitizer are used before autocorrelating short (80–160 ns) subsamples of the total waveform to measure the reflected delay time. That is, a smaller amplitude version of the original waveform appears time shifted by twice the transit time in the cable and this time is estimated via autocorrelation. The advantage of this method is that a new subsample needs only to be selected from a time increment in which new spectral information is present for a new measure of the length to be made. In this manner, many more length estimates can be averaged to establish the VOD than with the Gaussian approach. As a result, a detailed description of the implementation of both methods is presented together with an example of the type of data collected and limitations found.

47 OTHER INSTRUMENTATION↗

Machine Learning Based Cavity Fault Classification and Prediction

We report on the development of machine learning models for classifying C100 superconducting radio frequency (SRF) cavity faults in the Continuous Electron Beam Accelerator Facility (CEBAF) at Jefferson Lab. CEBAF is a continuous-wave recirculating linac utilizing 418 SRF cavities to accelerate electrons up to 12 GeV through 5-passes. Of these, 96 cavities (12 cryomodules) are designed with a digital low-level RF system configured such that a cavity fault triggers waveform recordings of 17 RF signals for each of the eight cavities in the cryomodule. Subject matter experts (SME) can analyze the collected time-series data, identify which of the eight cavities faulted first, and classify the type of fault. This information is used to find trends and strategically deploy mitigations to problematic cryomodules. However, manually labeling the data is laborious and time-consuming. By leveraging machine learning, near real-time – rather than post-mortem – identification of the offending cavity and classification of the fault type has been implemented. We discuss the performance of the ML models during a recent physics run.

43 PARTICLE ACCELERATORS↗

Analysis of the Accuracy of Actuation Electronics in the Laser Interferometer Space Antenna Pathfinder

The Laser Interferometer Space Antenna Pathfinder (LPF) main observable, labelled∆g, is the differential force per unit mass acting on the two test masses in free fall condition, after the contribution of all non-gravitational forces have been compensated. At low frequencies the differential force is compensated by an applied electrostatic actuation force,which then must be subtracted from the measured acceleration to obtain∆g. Any inaccuracy in the actuation force contaminates the residual acceleration. This study investigates the accuracy of the electrostatic actuation system and its impact on the LPF main observable. It is shown that the inaccuracy is mainly caused by the rounding errors in the waveform processing and also by the random error caused by the analog to digital converter (ADC) random noise in the control loop. Both errors are one order of magnitude smaller than the resolution of the commanded voltages. We developed a simulator based on the LPF design to compute the close-to-reality actuation voltages and consequently, the resulting actuation forces. The simulator is applied in post-processing the LPF data.

M. Armano↗