Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “density estimation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Electron Bernstein wave conversion of high-field side injected X-modes in QUEST

This paper presents a detailed design of the Q-shu University experimental steady state spherical tokamak's (QUEST's) high-field side (HFS) injection system for electron Bernstein wave (EBW) excitation and the results of an experimental comparison of the HFS eXtraordinary X-mode and low-field side (LFS) ordinary O-mode injection of 8.2 GHz radio frequency (RF) power. Waveguides, as an alternative to mirror polarizers for transmitting RF X-mode power from LFS to HFS for EBW conversion, were used instead of the installation of an RF mirror. Testing of LFS-to-HFS RF power transmission at 8.2 GHz, using an RG-50-type vacuum waveguide in a bench-scale device filled with SF6 gas at 0.03 Mpa, revealed that an RF power of 10.8 kW could traverse the fundamental electron cyclotron resonance layer for 60 s without breakdown. The short-length, open-ended waveguide antenna used in the HFS injection-induced wave diffraction reduced the efficiency of power delivery to the upper hybrid resonance (UHR) by approximately 7% at an electron temperature of 50 eV. The HFS injection was able to produce brighter camera images than the standard LFS injection. The location of the UHR, as estimated by measuring the density with an interferometer, agreed with its location as measured by plasma radiation low-field, side-edge positions shown by fast camera imaging. This indicates that the plasma was produced by mode-converted EBW. The HFS injection had an absorption efficiency of 96%, compared to 40% for LFS. A greater fluctuation of floating potential adjustable to the lower hybrid wave (LHW) was observed in the HFS case by installing a Langmuir probe, confirming that EBW conversion efficiency was higher in the HFS case. Moreover, after setting the poloidal field to B PF = 7.6 mT, plasma current (I P ) in the HFS peaked at 1.3 kA, as opposed to 0.3 kA for LFS, despite LFS injection having a total power of 55 kW, compared to 40 kW for HFS. However, as the impurity level was comparatively high, it is believed that this I P is dominated by pressure-drive, which makes it difficult to analyze EBWCD. Finally, the line-integrated density in the HFS injection peaked at 1.6 × 10 18 m -2 , compared to 8 × 10 17 m -2 in the LFS one.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Modeling turbulent impurity transport in the SOL of DIII-D with a reduced model

A novel impurity transport model that approximates SOL turbulence as a fluctuating poloidal electric field is shown to be an acceptable replacement for the traditional approach of assigning an arbitrary radial diffusion coefficient to the impurity ions. The model is implemented in the DIVIMP impurity transport code and applied to an L-Mode tungsten divertor experiment on DIII-D. The poloidal electric field is represented as fluctuating between ±1000 V m –1 based on previous measurements. The resulting intermittent v r = E θ × B T transport causes ions to transport both into the core as well as into the far-SOL. Simultaneous agreement with estimates of the W density just inside the separatrix as well as in the far-SOL is obtained (n W ~ 10 14 m –3 and n W ~ 10 12 m –3 , respectively). Prompt re-deposition of the W ions was necessary to obtain agreement (f redep ~ 99%). Here, we conclude that simulating impurity transport using a physics-based approximation for turbulence in the SOL, versus arbitrarily assigning diffusion coefficients, may enable better reactor scale predictions of core impurity contamination.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2026

Extensive analysis of reconstruction algorithms for DESI 2024 baryon acoustic oscillations

Reconstruction of the baryon acoustic oscillation (BAO) signal has been a standard procedure in BAO analyses over the past decade and has helped to improve the BAO parameter precision by a factor of ∼2 on average. The Dark Energy Spectroscopic Instrument (DESI) BAO analysis for the first year (DR1) data uses the “standard” reconstruction framework, in which the displacement field is estimated from the observed density field by solving the linearized continuity equation in redshift space, and galaxy and random positions are shifted in order to partially remove non-linearities. There are several approaches to solving for the displacement field in real survey data, including the multigrid (MG), iterative Fast Fourier Transform (iFFT), and iterative Fast Fourier Transform particle (iFFTP) algorithms. In this work, we analyze these algorithms and compare them with various metrics including two-point statistics and the displacement itself using realistic DESI mocks. We focus on three representative DESI samples, the emission line galaxies (ELG), quasars (QSO), and the bright galaxy sample (BGS), which cover the extreme redshifts and number densities, and potential wide-angle effects. We conclude that the MG and iFFT algorithms agree within 0.4% in post-reconstruction power spectrum on BAO scales with the RecSym convention, which does not remove large-scale redshift space distortions (RSDs), in all three tracers. The RecSym convention appears to be less sensitive to displacement errors than the RecIso convention, which attempts to remove large-scale RSDs. However, iFFTP deviates from the first two; thus, we recommend against using iFFTP without further development. In addition, we provide the optimal settings for reconstruction for five years of DESI observation. The analyses presented in this work pave the way for DESI DR1 analysis as well as future BAO analyses.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2020

The PAU Survey: Photometric redshifts using transfer learning from simulations

In this paper, we introduce the DEEPZ deep learning photometric redshift (photo-z) code. As a test case, we apply the code to the PAU survey (PAUS) data in the COSMOS field. DEEPZ reduces the σ68 scatter statistic by 50 percent at iAB = 22.5 compared to existing algorithms. This improvement is achieved through various methods, including transfer learning from simulations where the training set consists of simulations as well as observations, which reduces the need for training data. The redshift probability distribution is estimated with a mixture density network (MDN), which produces accurate redshift distributions. Our code includes an autoencoder to reduce noise and extract features from the galaxy SEDs. It also benefits from combining multiple networks, which lowers the photo-z scatter by 10 percent. Furthermore, training with randomly constructed coadded fluxes adds information about individual exposures, reducing the impact of photometric outliers. In addition to opening up the route for higher redshift precision with narrow bands, these machine learning techniques can also be valuable for broad-band surveys.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2020

Redshift inference from the combination of galaxy colours and clustering in a hierarchical Bayesian model – Application to realistic N -body simulations

ABSTRACT Photometric galaxy surveys constitute a powerful cosmological probe but rely on the accurate characterization of their redshift distributions using only broad-band imaging, and can be very sensitive to incomplete or biased priors used for redshift calibration. A hierarchical Bayesian model has recently been developed to estimate those from the robust combination of prior information, photometry of single galaxies, and the information contained in the galaxy clustering against a well-characterized tracer population. In this work, we extend the method so that it can be applied to real data, developing some necessary new extensions to it, especially in the treatment of galaxy clustering information, and we test it on realistic simulations. After marginalizing over the mapping between the clustering estimator and the actual density distribution of the sample galaxies, and using prior information from a small patch of the survey, we find the incorporation of clustering information with photo-z’s tightens the redshift posteriors and overcomes biases in the prior that mimic those happening in spectroscopic samples. The method presented here uses all the information at hand to reduce prior biases and incompleteness. Even in cases where we artificially bias the spectroscopic sample to induce a shift in mean redshift of $\Delta \bar{z} \approx 0.05,$ the final biases in the posterior are $\Delta \bar{z} \lesssim 0.003.$ This robustness to flaws in the redshift prior or training samples would constitute a milestone for the control of redshift systematic uncertainties in future weak lensing analyses.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2020

High resolution X-ray spectroscopy of Supergiant HMXB 4U1700-37 during the compact object eclipse.

In this work, we present an analysis of the first observation of the iconic High Mass X-ray Binary 4U 1700-37 with the Chandra High Energy Transmission Gratings during an X-ray eclipse. The goal of the observation was to study the structure/physical conditions in the clumpy stellar wind through high resolution spectroscopy. We find that: a) emission line brightness from K shell transitions, corresponding to near neutral species, directly correlates with continuum illumination. However, these lines do not greatly diminish during eclipse. This is readily explained if fluorescence Kα emission comes from the bulk of the wind. b) The highly ionised Fe xxv and Fe xxvi Lyα diminish during eclipse. Thus, they must be produced in the vicinity of the compact object where log ξ > 3. c) to describe the emission line spectrum, the sum of two self consistent photo ionisation models with low ionisation (log ξ ~ -1) and high ionisation (log ξ ~2.4) is required. From their emission measures, the clump-to-interclump density ratio can be estimated to be nc/ni ~ 300. To fit the complex He-like Si xiii profile, the plasma requires a broadening with vbulk ~ 840 km s-1. Reproducing the observed r ≈ f line fluxes requires the addition of a third collisionally ionised plasma. d) Emission lines widths appear unresolved at the hetg gratings resolution with exception of Silicon. There is no clear radial segregation between (quasi)neutral and ionised species, consistent with cold wind clumps interspersed in a hot rarefied interclump medium.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2021

Type Ia supernova magnitude step from the local dark matter environment

ABSTRACT Residuals in the Hubble diagram at optical wavelengths and host galaxy stellar mass are observed to correlate in type Ia supernovae (SNe Ia) (‘magnitude step’). Among possible progenitor channels for the associated explosions, those based on dark matter (DM) have attracted significant attention, including our recent proposal that ‘normal’ SNe Ia from bare detonations in sub-Chandrasekhar white dwarf stars are triggered by the passage of asteroid-mass primordial black holes (PBHs): the magnitude step could then originate from a brightness dependence on stellar properties, on DM properties, or both. Here, we present a method to estimate the local DM density and velocity dispersion of the environment of SN Ia progenitors. We find a luminosity step of $0.52\pm 0.11\,$ mag corresponding to bins of high versus low DM density in a sample of 222 low-redshift events from The Open Supernova Catalog. We investigate whether the magnitude step can be attributed to local DM properties alone, assuming asteroid-mass PBHs. Given the inverse correlation between SN Ia brightness and PBH mass, an intriguing explanation is a spatially inhomogeneous PBH mass function. If so, a strong mass segregation in the DM density-dependent PBH mass scale is needed to explain the magnitude step. While mass segregation is observed in dense clusters, it is unlikely to be realized on galactic scales. Therefore, if DM consists of asteroid-mass PBHs, the magnitude step is more likely to exist, and dominantly to be attributed to local stellar properties.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2022

The Davis–Chandrasekhar–Fermi method revisited

ABSTRACT Despite the rich observational results on interstellar magnetic fields in star-forming regions, it is still unclear how dynamically significant the magnetic fields are at varying physical scales, because direct measurement of the field strength is observationally difficult. The Davis–Chandrasekhar–Fermi (DCF) method has been the most commonly used method to estimate the magnetic field strength from polarization data. It is based on the assumption that gas turbulent motion is the driving source of field distortion via linear Alfvén waves. In this work, using MHD simulations of star-forming clouds, we test the validity of the assumption underlying the DCF method by examining its accuracy in the real 3D space. Our results suggest that the DCF relation between turbulent kinetic energy and magnetic energy fluctuation should be treated as a statistical result instead of a local property. We then develop and investigate several modifications to the original DCF method using synthetic observations, and propose new recipes to improve the accuracy of DCF-derived magnetic field strength. We further note that the biggest uncertainty in the DCF analysis may come from the linewidth measurement instead of the polarization observation, especially since the line-of-sight gas velocity can be used to estimate the gas volume density, another critical parameter in the DCF method.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2025

Seedless nonresonant gas-flow velocimetry with single-shot coherent Rayleigh-Brillouin scattering

We demonstrate neutral gas-flow velocimetry by exploiting the optical dipole forces exerted by precisely tailored high-intensity laser fields on polarizable particles, in the form of single-shot coherent Rayleigh-Brillouin scattering (CRBS). This enables mapping of the velocity distribution function of the particles in a single laser shot of approximately 200 ns duration, allowing us to perform spectroscopic measurements in the time, rather than the frequency, domain. Importantly, CRBS results in a coherent signal beam, which renders the technique ideal for measurements in optically noisy environments. By correlating the time shift of the resulting spectrum to the Doppler shift caused by the bulk motion of particles, we perform neutral gas-flow velocimetry without the need to seed the flow, nondestructively, for a variety of gases, atomic or molecular. We demonstrate gas-flow velocimetry at flow velocities as low as 1 m ⁢s −1 , with similar velocity resolution, while temperature and gas density can also be estimated from the same single-shot spectra. To prove the effectiveness of the measurement technique, we benchmark it against Pitot tube measurements, which show excellent agreement.

Gerakis, Alexandros [Luxembourg Institute of Scien↗
DOE OSTI2024

Reactor wall effects in Si–Cl 2 –Ar atomic layer etching

This work complements our previous manuscript [J. Vac. Sci. Technol. A41, 062602 (2023)] where predictions from molecular dynamics (MD) simulations of silicon–chlorine–argon (Si–Cl 2 –Ar) atomic layer etching (ALE) are compared to experiments. When etch product distributions for atomic chlorine (Cl) and silicon chlorides were initially compared to optical emission spectroscopy (OES) signals, it appeared that there was a discrepancy between the MD predictions and experimental results at higher ion fluences. Experiments showed a relatively long period of nearly constant Cl-containing etch products released from the ion-bombarded surface (referred to as the “plateau”) but this effect was not observed in MD simulations. In this report, we demonstrate that the “plateau” observed in the OES signals is most likely due to the desorption of Cl-containing etch products from the walls of the reactor and subsequent adsorption on the Si substrate. Experiments varying the gas residence time in the chamber while keeping incoming gas concentrations and pressure constant support this interpretation. We also conducted experiments with an additional Ar-only flow in the chamber to reduce the concentration of Cl-containing species on the chamber walls. For both sets of flow modification experiments, we observe results consistent with the hypothesis that Cl-containing species desorbing from chamber walls are a significant cause of the observed discrepancy between MD predictions and experimental observations. If the measured OES signals are corrected for this “additional” source of Cl-containing species at the surface, the MD predictions and measured OES signals are in excellent agreement. This further supports the predictive capability of MD simulations to accurately capture the relevant physical and chemical processes in plasma-assisted ALE processes. We provide an order of magnitude estimate of the required density of Cl-containing species that would account for the additional etch products observed. Finally, we discuss the implications of this effect on ALE in plasma nanofabrication.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Effects of forest degradation classification on the uncertainty of aboveground carbon estimates in the Amazon

Tropical forests are critical for the global carbon budget, yet they have been threatened by deforestation and forest degradation by fire, selective logging, and fragmentation. Existing uncertainties on land cover classification and in biomass estimates hinder accurate attribution of carbon emissions to specific forest classes. In this study, we used textural metrics derived from PlanetScope images to implement a probabilistic classification framework to identify intact, logged and burned forests in three Amazonian sites. We also estimated biomass for these forest classes using airborne lidar and compared biomass uncertainties using the lidar-derived estimates only to biomass uncertainties considering the forest degradation classification as well. Our classification approach reached overall accuracy of 0.86, with accuracy at individual sites varying from 0.69 to 0.93. Logged forests showed variable biomass changes, while burned forests showed an average carbon loss of 35%. We found that including uncertainty in forest degradation classification significantly increased uncertainty and decreased estimates of mean carbon density in two of the three test sites. Our findings indicate that the attribution of biomass changes to forest degradation classes needs to account for the uncertainty in forest degradation classification. By combining very high-resolution images with lidar data, we could attribute carbon stock changes to specific pathways of forest degradation. This approach also allows quantifying uncertainties of carbon emissions associated with forest degradation through logging and fire. Both the attribution and uncertainty quantification provide critical information for national greenhouse gas inventories.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

Male Runners With Lower Energy Availability Have Impaired Skeletal Integrity Compared to Nonathletes

Abstract Context Female athletes, particularly runners, with insufficient caloric intake for their energy expenditure [low energy availability (EA) or relative energy deficiency] are at risk for impaired skeletal integrity. Data are lacking in male runners. Objective To determine whether male runners at risk for energy deficit have impaired bone mineral density (BMD), microarchitecture, and estimated strength. Design Cross-sectional. Setting Clinical research center. Participants 39 men (20 runners, 19 controls), ages 16–30 years. Main Outcome Measures Areal BMD (dual-energy x-ray absorptiometry); tibia and radius volumetric BMD and microarchitecture (high-resolution peripheral quantitative computed tomography); failure load (microfinite element analysis); serum testosterone, estradiol, leptin; energy availability. Results Mean age (24.5 ± 3.8 y), lean mass, testosterone, and estradiol levels were similar; body mass index, percent fat mass, leptin, and lumbar spine BMD Z-score (−1.4 ± 0.8 vs −0.8 ± 0.8) lower (P < .05); and calcium intake and running mileage higher (P ≤ .01) in runners vs controls. Runners with EA <median had lower lumbar spine (−1.5 ± 0.7, P = .028), while runners with EA ≥median had higher hip (0.3 ± 0.7 vs −0.4 ± 0.5, P = .002), BMD Z-scores vs controls. After adjusting for calcium intake and running mileage, runners with EA <median had lower mean tibial total and trabecular volumetric BMD, trabecular bone volume fraction, cortical porosity, and apparent modulus vs controls (P < .05). Appendicular lean mass and serum estradiol (R ≥ 0.45, P ≤ .046), but not testosterone, were positively associated with tibial failure load among runners. Conclusions Despite weight-bearing activity, skeletal integrity is impaired in male runners with lower caloric intake relative to exercise energy expenditure, which may increase bone stress injury risk. Lower estradiol and lean mass are associated with lower tibial strength in runners.

Haines, Melanie S. (ORCID:0000000310024754)↗
DOE OSTI2021

FePt binary alloy with 32 atoms - LSMS-3 data

This dataset contains the estimate of atomic charge density, atomic magnetic moment and total energy for 32,000 configurations of the iron-platinum (FePt) binary alloy with body-centered cubic (BCC) structure. The configurations span all the compositions from 0%Fe - 100% Pt through 100%Fe - 0% Pt. The results have been produced running ab-initio density functional theory (DFT) calculations with the LSMS-3 code on OLCF supercomputer Titan. LSMS-3 GitHub repository: https://github.com/mstsuite/lsms Deep Learning research papers published with results based on this dataset: Fast and stable deep-learning predictions of material properties for solid solution alloys Massimiliano Lupo Pasini, Ying Wai Li, Junqi Yin, Jiaxin Zhang, Kipton Barros and Markus Eisenbach Published 14 December 2020 • © 2020 IOP Publishing Ltd Journal of Physics: Condensed Matter, Volume 33, Number 8 Citation Massimiliano Lupo Pasini et al 2021 J. Phys.: Condens. Matter 33 084005 https://iopscience.iop.org/article/10.1088/1361-648X/abcb10

36 MATERIALS SCIENCE↗
DOE OSTI2021

CuAu binary alloy with 32 atoms - LSMS-3 data

This dataset contains the estimate of atomic charge density, atomic magnetic moment and total energy for 32,000 configurations of the iron-platinum (CuAu) binary alloy with face-centered cubic (FCC) structure. The configurations span all the compositions from 0%Cu - 100% Au through 100%Cu - 0% Au. The results have been produced running ab-initio density functional theory (DFT) calculations with the LSMS-3 code on OLCF supercomputer Titan. LSMS-3 GitHub repository: https://github.com/mstsuite/lsms Deep Learning research papers published with results based on this dataset: Fast and stable deep-learning predictions of material properties for solid solution alloys Massimiliano Lupo Pasini, Ying Wai Li, Junqi Yin, Jiaxin Zhang, Kipton Barros and Markus Eisenbach Published 14 December 2020. 2020 IOP Publishing Ltd Journal of Physics: Condensed Matter, Volume 33, Number 8 Citation Massimiliano Lupo Pasini et al 2021 J. Phys.: Condens. Matter 33 084005 https://iopscience.iop.org/article/10.1088/1361-648X/abcb10

36 MATERIALS SCIENCE↗
DOE OSTI2020

Dynamic pulse propagation modelling for predictive femtosecond-laser-microbonding of transparent materials

A dynamic pulse propagation modeling for femtosecond laser bonding of Borofloat glass is presented. The temperature evolution and internal modifications are predicted by incorporating the nonlinear electron dynamics along with temperature dependent thermal properties. The modelling predicts the spatial and temporal distribution of absorption coefficient and plasma density that gives quantitative estimations of the heat affected zone and weld geometry. The impact of focusing condition on heat affected zone and weld geometry is investigated, which for the first time to our knowledge allows to numerically determine the desired relative position between the geometrical focus of a femtosecond-laser-pulse and the interface of the two substrates to be welded. The prediction of the modelling on the offset distance is applied to weld Borofloat glass plates having optical contact and can be applied to other dielectric solids.

Sahoo, Pankaj K. (ORCID:0000000209437319)↗
DOE OSTI2023

Shock physics and shadowgraphic measurements of laser-produced cerium plasmas

Shadowgraphic measurements are combined with theory on gas-dynamics to investigate the shock physics associated with nanosecond laser ablation of cerium metal targets. Time-resolved shadowgraphic imaging is performed to measure the propagation and attenuation of the laser-induced shockwave through air and argon atmospheres at various background pressures, where stronger shockwaves characterized by higher propagation velocities are observed for higher ablation laser irradiances and lower pressures. The Rankine-Hugoniot relations are also employed to estimate the pressure, temperature, density, and flow velocity of the shock-heated gas located immediately behind the shock front, predicting larger pressure ratios and higher temperatures for stronger laser-induced shockwaves.

42 ENGINEERING↗
DOE OSTI2021

3D Tracking of a Single Electron in IOTA

High-resolution observations of single-particle dynamics have potential as a powerful tool in the diagnostics, tuning and design of storage rings. We are presenting the results of experiments with single electrons that were conducted at Fermilab’s IOTA ring to explore the feasibility of this approach. A set of sensitive, high-resolution digital cameras was used to detect the synchrotron radiation emitted by an electron, and the resulting images were used to reconstruct the time evolution of oscillation amplitudes in all three degrees of freedom. From the evolution of the oscillation amplitudes, we deduce transverse emittances, momentum spread, damping times, beam energy and estimated residual-gas density and composition. To our knowledge, this is the first time that the dynamics of a single particle in a storage ring has been tracked in all three dimensions. We discuss farther development of a single particle diagnostics that may allow reconstruction of its turn-by-turn coordinates over macroscopic periods of time facilitating ultra-precise lattice diagnostics and direct benchmarking of tracking codes.

43 PARTICLE ACCELERATORS↗
DOE OSTI2020

The Utility of Satellites and Autonomous Remote Sensing Platforms for Monitoring Offshore Aquaculture Farms: A Case Study for Canopy Forming Kelps

The emerging sector of offshore kelp aquaculture represents an opportunity to produce biofuel feedstock to help meet growing energy demand. Giant kelp represents an attractive aquaculture crop due to its rapid growth and production, however precision farming over large scales is required to make this crop economically viable. These demands necessitate high frequency monitoring to ensure outplant success, maximum production, and optimum quality of harvested biomass, while the long distance from shore and large necessary scales of production makes in person monitoring impractical. Remote sensing offers a practical monitoring solution and nascent imaging technologies could be leveraged to provide daily products of the kelp canopy and subsurface structures over unprecedented spatial scales. Here, we evaluate the efficacy of remote sensing from satellites and aerial and underwater autonomous vehicles as potential monitoring platforms for offshore kelp aquaculture farms. Decadal-scale analyses of the Southern California Bight showed that high offshore summertime cloud cover restricts the ability of satellite sensors to provide high frequency direct monitoring of these farms. By contrast, daily monitoring of offshore farms using sensors mounted to aerial and underwater drones seems promising. Small Unoccupied Aircraft Systems (sUAS) carrying lightweight optical sensors can provide estimates of canopy area, density, and tissue nitrogen content on the time and space scales necessary for observing changes in this highly dynamic species. Underwater color imagery can be rapidly classified using deep learning models to identify kelp outplants on a longline farm and high acoustic returns of kelp pneumatocysts from side scan sonar imagery signal an ability to monitor the subsurface development of kelp fronds. Current sensing technologies can be used to develop additional machine learning and spectral algorithms to monitor outplant health and canopy macromolecular content, however future developments in vehicle and infrastructure technologies are necessary to reduce costs and transcend operational limitations for continuous deployment in an offshore setting.

54 ENVIRONMENTAL SCIENCES↗