Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “contact pressure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Evaluating Pressure‐dependent Discharge Behavior of Foil Versus In situ Plated Lithium Metal Anodes in Solid‐State Batteries

Abstract Anode‐free manufacturing of solid‐state batteries (SSBs) shows promise to maximize energy density by eliminating excess lithium (Li) and simplifying battery production. However, high reversibility during discharge (stripping of Li) is necessary for long‐lifetime SSBs with a limited Li reservoir. Further, the plastic flow of Li changes depending on the Li thickness, leading to possible differences in discharge performance under stack pressure. This work investigates the pressure‐dependent discharge performance of anode‐free manufactured SSBs with in situ plated Li and compares the performance to that of conventional thick Li foil cells. Distinct stripping behavior is observed at low pressures (0–1 MPa), where Li diffusivity and initial interfacial contact may control accessible capacity, compared to high pressures (3–10 MPa) where mechanical deformation of Li likely governs stripping behavior. Analysis of impedance spectra collected during stripping shows that additional stack pressure delays the formation of deep, as opposed to lateral, voids in the Li anode. These results provide insights to guide the transition from thick Li foil anodes to anode‐free manufactured SSBs.

Haslam, Catherine G.↗
NASA NTRS1983

Flexible Seal Accommodates Part Mismatch

Chain of plates embedded in flexible seal enables it to withstand side loading of 2,300 psi (116MPa) while sealing gap of up to 0.5 inch (13 mm) between cylindrical chamber wall and test fixture. Pressure-actuated seal along inner edge forces seal into contact even though cylinder wall becomes eccentric as cylinder pressure increases. Seal has many industrial applications, particularly where heat or pressure causes distortion of chamber being sealed.

Bobb, I.↗
NASA NTRS1994

A hybrid simulation of contact discontinuity

Contact discontinuities in a collisionless plasma are studied by hybrid simulations, in which ions are treated as particles and electrons are considered as a fluid. It is demonstrated that contact discontinuity with a stable density ramp can exist in cases with a finite electron temperature. An electron pressure gradient is present across the contact discontinuity, leading to the presence of a parallel electric field and hence field-aligned potential increase (Delta Phi (sub parallel)) in the transition region. By reflecting ions at the discontinuity, this parallel electric potential peak reduces the interpenetration between hot and cold ions and maintains a stable density ramp across the contact discontinuity. The ratio of the field-aligned electric potential energy to ion thermal energy, e(Delta) Phi(sub parallel)/kT(sub i), is found to be an increasing function of T(sub e)/T(sub i), where T(sub e) and T(sub i) are respectively the electron and ion temperature.

Wu, B. H.↗
DOE OSTI2024

Superlubricity coating containing carbon nanotubes

A method for producing a structure containing an array of MWCNTs on a metal substrate, comprising: (i) subjecting a metal substrate to a surface oxidation process at a first elevated temperature in an oxygen-containing atmosphere and under a first reduced pressure; (ii) subjecting the metal substrate to a surface reduction process at a second elevated temperature in a reducing atmosphere and under a second reduced pressure of at least 0.01 atm and less than 1 atm to result in reduction of the surface of said metal substrate, wherein the reducing atmosphere contains hydrogen gas; (iii) subjecting the metal substrate to a third reduced pressure of no more than 0.1 atm; and (iv) contacting the metal substrate, while at the third reduced pressure and under an inert or reducing atmosphere, with an organic substance at a third elevated temperature for suitable time to produce the MWCNTs on the metal substrate.

Ihala Gamaralalage, Chanaka Kapila↗
DOE OSTI2023

Sulfur Polymers as Flexible Interfacial Additives for Low Stack-Pressure Solid-State Lithium-Ion Batteries

Solid-state batteries (SSBs) fabricated using sulfide solid electrolytes (SSEs) typically require cell stack-pressures in the range of tens to hundreds of megapascals to maintain effective interfacial contact and lithium-ion mobility across the full cell stack. These relatively high cell stack-pressures necessarily require additional cell components that reduce the delivered volumetric and gravimetric capacities of SSBs. This work has developed a novel sulfur polymer (polyS) that improves lithium-ion conductivity in SSBs at low cell stack-pressures, thereby directly targeting this technological limitation. Specifically, this work shows that polyS can be combined with the argyrodite Li6PS5Cl (LPSC) to form a stable composite SSE. By combining LPSC particles with a flexible additive that enhances interfacial contact at low pressures, this new polyS LPSC composite SSE material greatly improves ionic conductivity at cell stack-pressures below 2.0 MPa in comparison to conventional LPSC composites. Furthermore, this polyS LPSC composite can be used to fabricate a full SSB that cycles reversibly at only 1.6 MPa. Finally, this composite SSE exhibits self-healing behavior when combined with a lithium metal electrode, wherein lithium dendrites are oxidized to form passivating Li2S species that recover the cell from shorting.

ENERGY STORAGE↗
DOE OSTI2022

Operating High-Energy Lithium-Metal Pouch Cells with Reduced Stack Pressure Through a Rational Lithium-Host Design

Transitioning from a liquid electrolyte to an inorganic solid electrolyte offers a potential pathway to enable highly reversible lithium-metal anodes. However, the solid-electrolyte-protected lithium-metal anode suffers from poor interfacial ionic contacts and requires an impractically high stack pressure (>1.0 MPa) to maintain the interfacial contacts. It is demonstrated here that combining a hollow silver/carbon fiber scaffold and an inorganic/organic composite electrolyte enables a highly reversible lithium-metal anode. Since the high surface area of the electrode provides intimate contact and the hollow structure of the electrode relieves the lithium plating-induced stress, the electrode/electrolyte interface remains stable during cycling even under mild stack pressure. This unconventional structural design is validated in practical pouch cells assembled with the 3D lithium host containing a onefold excess of lithium and a high-nickel cathode. At a mild stack pressure of 320 kPa, the pouch cell displays 83% capacity retention for 200 cycles. This work illustrates that combining a hollow electrode architecture and a robust solid electrolyte offers a practical pathway toward rechargeable lithium-metal anodes.

36 MATERIALS SCIENCE↗
NASA NTRS1980

Evaluation of space shuttle main engine bearings from high pressure oxygen turbopump 9008

Two used turbopump mainshaft support bearings were examined to determine steps needed to achieve turbopump lifetimes of 27,000 seconds. The two bearings, which had been run in a high pressure oxygen turbopump, are angular contact ball bearings, applied as a preloaded pair, locked to the shaft, inner race rotating, with the outer races unrestrained axially. Examination showed that both bearings had been subjected to overloads, leading to fatigue spalling on the races and balls and advanced retainer wear. This is clear evidence of unintended high internal loads in the high pressure oxygen pump which would lead to complete bearing failure and extensive secondary pump damage. Action must be taken to reduce the applied bearing loads or to incorporate bearings of sufficient size to withstand the high loads.

Dufrane, K. F.↗
NASA NTRS2009

Preliminary Test Results of a Non-Contacting Finger Seal on a Herringbone-Grooved Rotor

The baseline non-contacting finger seal is a NASA patented design. The primary difference between it and Gul Aroras design patented by AlliedSignal is that there are no lift pads on the high pressure fingers. The baseline non-contacting finger seal is comprised of a back plate, aft spacer, aft (or low pressure) finger element, forward (or high pressure) finger element, forward spacer, and front plate. The components are held together with 20 flat head screws. A typical seal would have a back plate of approximately the same thickness as the front plate and would be riveted together. The thicker back plate allows use of threaded fasteners so that different finger elements can be tested without having to replace all the individual seal components. The finger elements are essentially washers made of thin sheet stock with multiple curved slots machined around the inner diameter to form the fingers. They are clocked so that the fingers of one cover the slots of the other. The aft finger element fingers have axial extensions or "lift pads" at the seal id that are concentric to the rotor. The fingers act as cantilever beams and flex in response to rotor dynamic motion and radial growth of the rotor due to centrifugal or thermal forces.

Proctor, Margaret P.↗
DOE OSTI2022

Microscale THMC Modeling of Pressure Solution in Salt Rock: Impacts of Geometry and Temperature

Abstract Pressure solution, a mechanism that involves tight coupling between the geometry and thermal-hydro-mechanical-chemical (THMC) processes, plays an important role in diagenesis. In this study, we make the first attempt to conduct microscale THMC modeling to understand and quantify the impacts of geometry and temperature on pressure solution, taking natural salt rock as an example. This modeling capability is achieved by expanding a novel MC code that we developed previously (Hu et al. J Geophys Res: Solid Earth 126:e2021JB023112, 2021) to include temperature effects. We first conduct a simulation of an example that involves a single brine inclusion within a single halite grain and find that the temperature impact is limited for that case. We then extract geometry from an image of a natural salt rock and conduct simulations with different cases: (A) only temperature and no stress, (B) only stress and no temperature, and (C) with both stress and temperature. These different cases result in quite different phenomena. In case A, dissolution and precipitation occur across the entire system due to isolated pore space reaching a localized mass balance between dissolution, precipitation, and diffusion. In case B, intense geometric features (e.g., major asperities, inclusions) in one area undergo stress concentration, thus dominating pressure solution in that area. In case C, pressure solution is spread out at contacting highly stressed geometric features close to the hotter side. We conclude that geometric features dominate stress distribution, thus dominating pressure solution in a natural salt rock that may be affected by the temperature if a sufficient temperature gradient is applied.

58 GEOSCIENCES↗
NASA NTRS2006

Advanced Seal Rig Experiments and Analysis

Compliant Seals eg. Brush Seals, Finger Seals: a) 3-5X flow reduction; b) developing higher surface speed, temperature, and pressure levels; c) interference/debris/durability issues. Non Contact Seals eg. Aspirating, Film Riding: a) 5-10X flow reduction but still improving surface speed, temperature, and delta pressure levels; b) limited applications; c) interference issues. Labyrinth Seals still the workhorse seal in gas turbine engines: a) long history of use in compressors, turbines, around bearing compartments; b) cheaper to make than many other seals; c) small improvement x many seals (up to 50*) = big gain in performance/operability; d) well and still investigated by academia & industry; e) with a proper abradable seal land can handle interference.

Paolillo, Roger↗
NASA NTRS1976

A dynamic pressure source for the calibration of pressure transducers

A dynamic pressure source is described for producing sinusoidally varying pressures of up to 34 kPa zero to peak, over the frequency range of approximately 50 Hz to 2 kHz. The source is intended for the dynamic calibration of pressure transducers. The transducer to be calibrated is mounted near the base of the thick walled aluminum tube forming the vessel so that the pressure sensitive element is in contact with the liquid in the tube. A section of the tube is filled with small steel balls to damp the motion of the 10-St dimethyl siloxane working fluid in order to extend the useful frquency range to higher frequencies than would be provided by an undamped system. The dynamic response of six transducers provided by the sponsor was evaluated using the pressure sources; the results of these calibrations are given.

Vezzetti, C. F.↗
DOE OSTI2023

Understanding the Mechanisms of Self-Organization in Atmospheric Pressure DC Glows

One of the most challenging areas in atmospheric pressure plasmas is controlling uniformity and contact area. Indeed it is this problem which is closely related to scale up that has impeded the widespread applications of these plasmas. The atmospheric pressure plasma glow is a type of atmospheric pressure discharge akin to a traditional low pressure glow particularly when compared with discharge morphology. But this is where the similarities end. Unlike low pressure glows, atmospheric pressure glows do not rely on electrode processes such as secondary electron emission to make the discharge self-sustaining, rather the discharge is sustained by typically processes such as the presence of a resistive layer or through favorable atomic collisional processes such as that which prevail in helium that stabilizes the discharge so that the thermal instability is mitigated. These discharges can feature either solid metal electrodes or geometries where at least one electrode is a liquid water electrolyte. Regardless of the implementation, DC 1 Atm glows are fascinating in that the plasma attachment under certain conditions can self-organize. The attachment surface area therefore changes as a result. Therefore, self-organization could be the key to optimizing plasma contact area and thereby open the door to applications in the real world. The plasma physical processes prevailing at the surface where the self-organization takes place remain largely unexplored. There is very little published research on the conditions that prevail at the surface and virtually no scholarship on measured plasma parameters of the self-organized attachments themselves or the surface electric field. This effort breaks new ground by elucidating these largely unexplored physical processes.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Phase Field Modeling of Pressure Induced Densification in Solid Electrolytes

Adoption of dense and homogeneous solid electrolytes can possibly mitigate the propagation of lithium dendrites and enable lithium metal anodes. Application of external pressure helps to minimize the sintering temperature in oxide ceramics and can potentially densify softer sulfide electrolytes even under room temperature conditions. Here, a previously developed phase field-based computational scheme for predicting the high-temperature sintering-induced densification of oxide ceramic solid electrolytes is extended in the present context to capture the influence of external pressure for densifying solid electrolytes. Two different bulk deformation mechanisms, namely, "reorganization" and "creep deformation," are dominant under external pressure, which is different from the surface and grain-boundary diffusion-induced densification of solid electrolytes that occurs during high temperature sintering. External pressure also increases the points of contact between the particles, which further enhances the propensity of diffusion-induced sintering process. Results obtained from simulations indicate that densification under external pressure is independent of the solid electrolyte particle morphology. Finally, a phase map is generated between applied pressure and temperature for achieving complete densification of oxide ceramics, which can possibly guide the synthesis of thin and dense solid electrolyte separators.

25 ENERGY STORAGE↗
NASA NTRS1982

Elastohydrodynamic lubrication of elliptical contacts

Fully flooded, elastohydrodynamically lubricated, elliptical contacts are discussed. The relevant equations used in the elastohydrodynamic lubrication (EHL) of elliptical contacts are briefly described. Film thickness equations are developed for materials of high elastic modulus, such as metal, and for materials of low elastic modulus, such as rubber. In addition to the film thickness equations that are developed, plots of pressure and film thickness are presented. A theoretical study of the influence of lubricant starvation on film thickness and pressure in hard and soft elliptical elastohydrodynamic contacts is presented. From the results for both hard and soft EHL contacts a simple and important dimensionless inlet boundary distance is specified. It is also found that the film thickness for a starved condition can be written in dimensionless terms as a function of the inlet distance parameter and the film thickness for a fully flooded condition. contour plots of pressure and film thickness in and around the contact are shown for fully flooded and starved conditions. The theoretical findings are compared directly with results obtained experimentally.

Hamrock, B. J.↗
DOE OSTI2020

Atmospheric-pressure ionization and fragmentation of molecules for structural elucidation

A solution-cathode glow discharge (SCGD) spectrometry apparatus may comprise an SCGD source and a mass or ion mobility spectrometer. A method for ionizing a molecular analyte may comprise contacting the molecular analyte with a plasma discharge to form ions and separating the ions in a mass spectrometer or ion mobility spectrometer. The contacting step may occur under atmospheric pressure and/or ambient conditions. The molecular analyte may be fragmented by the plasma discharge.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1972

Isothermal elastohydrodynamic theory for the full range of pressure-viscosity coefficient.

The isothermal, elastohydrodynamic (EHD) solutions in the inlet region of line contacts are extended to cover the full range of pressure-viscosity parameter, G, and the region of extremely heavy loads. The effect of a composite exponential model for the pressure-viscosity dependence on the film thickness is also studied. Results of the film thickness are compared with those based on work by Grubin, Dowson-Higginson, Bell and Kannel, and Herrebrugh. Comparison is also made between the theoretical results with the recently obtained X-ray film thickness measurements.

Cheng, H. S.↗
NASA NTRS1989

O-ring sealing verification for the space shuttle redesign solid rocket motor

As a part of the redesign of the Space Shuttle Solid Rocket Motor, the field and nozzle-to-case joints were redesigned to minimize the dynamic flexure caused by internal motor pressurization during ignition. The O-ring seals and glands for the joints were designed to accommodate both structural deflections and to promote pressure assistance. A test program was conducted to determine if a fluorocarbon elastomeric O-ring could meet this criteria in the redesigned gland. Resiliency tests were used to investigate the O-ring response to gap motion while static seal tests were used to verify design criteria of pressure assistance for sealing. All tests were conducted in face seal fixtures mounted in servo-hydraulic test machines. The resiliency of the O-ring was found to be extremely sensitive to the effects of temperature. The External Tank/Solid Rocket Booster attach strut loads had a negligible affect on the ability of the O-ring to track the simulated SRB field joint deflection. In the static pressure-assisted seal tests, as long as physical contact was maintained between the O-ring and the gland sealing surface, pressure assistance induced instantaneous sealing.

Lach, Cynthia L.↗