SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Widths and spacings of conductor lines on integrated circuits measured electrically by split cross-bridge resistor technique. Speeds evaluation of integrated-circuit fabrication processes. When measurement of probe currents and voltages and reduction of measurement data automated, test structure probed and characterized in less than one second.
Portable testing circuit enables technician to determine quickly wiring errors in multiple-conductor electrical cable or terminal connectors. Active unit tester made of inexpensive integrated circuits and other readily available components. Timer and one-shot generate pulses counted by shift registers. Shift-register output terminals wired to connector pins so voltage applied to each pin in sequence.
Analytical expressions are derived for the cutoff wavenumbers and the corresponding modes in annular-cross-section waveguides having inner conductors of small radius. Waveguides with circular and rectangular outer boundary are considered. In the case of the circular eccentric annular waveguide, comparison is made between the values of cutoff wavenumbers computed from the expressions derived in this paper and data obtained by a more rigorous numerical technique.
The radar cross section (RCS) of a circular waveguide terminated by a perfect electric conductor is calculated by the geometrical theory of diffraction for the rim diffraction and by a physical optics approximation for the interior irradiation. The interior irradiation is generally more than 10 dB higher than the rim diffraction for a/lambda equal to or greater than 1 (a is the waveguide radius, lambda is the free-space wavelength). At low frequencies (a/lambda about 1), the interior irradiation can be significantly reduced over a broad range of incident angle if the interior waveguide wall is coated with a thin layer (1 percent of the radius) of lossy magnetic material. Our theoretical prediction is confirmed by measurements. At higher frequencies (a/lambda about 3), a thin layer of coating is effective for the case of near axial incidence, provided that a good transition of the TE(11) mode near the waveguide opening to the HE(11) mode inside the waveguide is made. A thicker layer of coating is required for the RCS reduction over wider incident angle.
An analysis of microstrip line structures in which either the strip or the ground plane or both are made of a high Tc superconductor is presented. The effect of implementation of a superconductor to the strip and the ground plane is explained with the calculation of a conductor loss of the structure by the Phenomenological Loss Equivalence Method (PEM). The theoretical values are compared with the experimental results from a ring resonator which is made of a gold ground plane and a high Tc superconductor, YBa2Cu3O(7-x), strip.
Surface impedance boundary conditions are employed to reduce the solution volume during the analysis of scattering from lossy dielectric objects. In a finite difference solution, they also can be utilized to avoid using small cells, made necessary by shorter wavelengths in conducting media, throughout the solution volume. A 1-D implementation for a surface impedance boundary condition for good conductors in the Finite Difference Time Domain (FDTD) technique.
Surface impedance boundary conditions are used to reduce the solution volume during the analysis of scattering from lossy dielectric objects. In a finite difference solution, they also can be used to avoid using small cells, made necessary by shorter wavelengths in conducting media, throughout the solution volume. A one dimensional implementation is presented for a surface impedance boundary condition for good conductors in the Finite Difference Time Domain (FDTD) technique. In order to illustrate the FDTD surface impedance boundary condition, a planar air-lossy dielectric interface is considered.
Conductor-backed coplanar waveguide (CBCPW) resonators operating at 10.8 GHz have been fabricated from laser ablated and off-axis magnetron sputtered YBa2Cu3O(7-delta) (YBCO) high-temperature superconducting (HTS) thin films on LaAlO3. These resonators were tested in the temperature range from 14 to 92 K. The unloaded quality factor at 77 K of the HTS CBCPW resonators was 3 to 4 times that of a similar gold resonator. To the authors' knowledge, these results represent the first reported measurements of HTS-based CBCPW resonators.
Conductor-backed coplanar waveguide (CBCPW) resonators operating at 10.8 GHz have been fabricated from Tl-Ba-Ca-O (TBCCO) and Y-Ba-Cu-O (YBCO) thin films on LaAlO3. The resonators consist of a coplanar waveguide (CPW) patterned on the superconducting film side of the LaAlO3 substrate with a gold ground plane coated on the opposite side. These resonators were tested in the temperature range from 14 to 106 K. At 77 K, the best of our TBCCO and YBCO resonators have an unloaded quality factor (Qo) 7 and 4 times, respectively, larger than that of a similar all-gold resonator. In this study, the Qo's of the TBCCO resonators were larger than those of their YBCO counterparts throughout the aforementioned temperature range.
Writing currents reduced to practical levels. Improved conceptual designs for writing conductors in micromagnet/Hall-effect random-access integrated-circuit memory reduces electrical current needed to magnetize micromagnet in each memory cell. Basic concept of micromagnet/Hall-effect random-access memory presented in "Magnetic Analog Random-Access Memory" (NPO-17999).
Anions that can form dissociative salts with Li(+) have been prepared and covalently attached to high surface area fumed silica. When blended with polyethylene oxide (PEO), the functionalized fumed silica suppresses the crystallization of the PEO, provides dimensional stability, and serves as a single ion conductor. Since functionalized fumed silica is easily dispersed in common polar solvents, it can be incorporated in both the polymer electrolyte and the electrodes.
Gaseous contaminants such as oxygen, water vapor, nitrogen and hydrocarbons are often present in the processing environment in semiconductor device fabrication and in containerless materials processing. The contaminants arise as a result of outgassing from hot surfaces or they may be part of the impurities in commercial ultra-high purity gases. Among these gaseous contaminants, oxygen is the most reactive and, therefore, has the most adverse effects on the end product. There has been an intense effort at the Jet Propulsion Laboratory to develop different types of oxygen sorbents to reduce oxygen concentration in a microgravity processing environment to sub-ppb (parts-per-billion) levels. Higher concentrations can lead to rapid surface oxide formation, hence reducing the quality of semiconductor devices. If the concentration of oxygen in a processing chamber at 1000oC is in the ppb level, it will only take approximately 10 seconds for an oxide layer to form on the surface of a sample. The interaction of oxygen with the water surface can lead to the formation of localized defects in semi-conductor devices, hence decreasing the manufacturing yield. For example, efficient production of 64 Mb RAM chips requires contaminations below ppb levels. This paper describes a technique for measuring trace quantities of oxygen contaminants by recording the monoatomic negative ions, O-, using mass spectrometry. The O- formation from the e--O2 interaction utilizes the electron dissociative attachment method that is greatly enhanced at the resonant energy (6.8 eV). The device combines a small gridded electron ionizer with a compact mass spectrometer. The concentrations of oxygen have been measured using the method of standard additions by diluting O2 in N2. The lowest detection limit obtained was 1.2 kHz (O- count rate) at a concentration of 10-10, corresponding to 0.1 ppb.
High Temperature Protonic Conductors (HTPC) with the perovskite structure are envisioned for electrochemical membrane applications such as H2 separation, H2 sensors and fuel cells. Successive membrane commercialization is dependent upon addressing issues with H2 permeation rate and environmental stability with CO2 and H2O. HTPC membranes are conventionally fabricated by solid-state sintering. Grain boundaries and the presence of intergranular second phases reduce the proton mobility by orders of magnitude than the bulk crystalline grain. To enhanced protonic mobility, alternative processing routes were evaluated. A laser melt modulation (LMM) process was utilized to fabricate bulk samples, while pulsed laser deposition (PLD) was utilized to fabricate thin film membranes . Sr3Ca(1+x)Nb(2-x)O9 and SrCe(1-x)Y(x)O3 bulk samples were fabricated by LMM. Thin film BaCe(0.85)Y(0.15)O3 membranes were fabricated by PLD on porous substrates. Electron microscopy with chemical mapping was done to characterize the resultant microstructures. High temperature protonic conduction was measured by impedance spectroscopy in wet air or H2 environments. The results demonstrate the advantage of thin film membranes to thick membranes but also reveal the negative impact of defects or nanoscale domains on protonic conductivity.
A new membrane composite material that combines an organosilica proton conductor with perfluorinated Nafion material to achieve good proton conductivity and high-temperature performance for membranes used for fuel cells in stationary, transportation, and portable applications has been developed. To achieve high proton conductivities of the order of 10(exp -1)S/cm over a wide range of temperatures, a composite membrane based on a new class of mesoporous, proton-conducting, hydrogen-bonded organosilica, used with Nafion, will allow for water retention and high proton conductivity over a wider range of temperatures than currently offered by Nafion alone. At the time of this reporting, this innovation is at the concept level. Some of the materials and processes investigated have shown good proton conductivity, but membranes have not yet been prepared and demonstrated.
The interaction between hydrogen and various high temperature protonic conductors (HTPC) has not been clearly understood due to poor densification and unreacted secondary phases. the melt-processing technique is used in producing fully dense simple SrCe(0.9)Y (0.10) O(3-delta) and complex Sr3Ca(1+x)Nb(2+x)O(9-delta) perovskites that can not be achieved by solid-state sintering. the possibilities of ion beam analysis have been investigated to quantify hydrogen distribution in HTPC perovskites subjected to water heat treatment. Nuclear microprobe technique is based on the interactions of a focused ion beam of MeV light ions (H-1, H-2, He-3, He-4,.) with the sample to be analyzed to determine local elemental concentrations at the cubic micrometer scale, the elastic recoil detection analysis technique (ERDA) has been carried out using He-4(+) microbeams and detecting the resulting recoil protons. Mappings of longitudinal sections of water treated SrCeO3 and Sr(Ca(1/3)Nb(2/3))O3 perovskites have been achieved, the water treatment strongly alters the surface of simple SrCe(0.9)Y(0.10)O(3-delta) perovskite. From Rutherford Back Scattering measurements (RBS), both Ce depletion and surface re-deposition is evidenced. the ERDA investigations on water treated Sr3Ca(1+x)Nb(2+x)O(9-delta) perovskite did not exhibit any spatial difference for the hydrogen incorporation from the surface to the centre. the amount of hydrogen incorporation for Sr3Ca(1+x)Nb(2+x)O(9-delta) was low and required further development of two less conventional techniques, ERDA in forward geometry and forward elastic diffusion H-1(p,p) H-1 with coincidence detection.
We validate through simulation and experiment that artificial magnetic conductors (AMC s) can be well characterized by a transmission line model. The theoretical bandwidth limit of the in-phase reflection can be expressed in terms of the effective RLC parameters from the surface patch and the properties of the substrate. It is found that the existence of effective inductive components will reduce the in-phase reflection bandwidth of the AMC. Furthermore, we propose design strategies to optimize AMC structures with an in-phase reflection bandwidth closer to the theoretical limit.
Sustainable aviation in the form of electrified propulsion is likely to lead to an increase in the electrical assets contained within a single aircraft. As a result, it is desirable to design light weight conductor materials, thus reducing the payload of components like motor windings, low voltage signal cables, and transmission cables for data and power. One approach involves replacing pure Cu wiring with metalized CNT composites. This paper evaluates a framework for modeling overall conductivity and current sharing within such composites. Processing methods and parameters were refined. Select electroplated samples outperformed pure Cu in conductivity and had comparable ultimate tensile strengths. Tensile strengths are expected to improve with an additional densification step during processing. Acoustic emission data was used to predict the failure mechanism of the composite. Theories explaining improved intrinsic conductivity are discussed, with a focus on chemical and mechanical interactions at the Cu-CNT interface. These include Cu infiltration of CNT crevices, CNT oxidation, activity at defects in CNT walls, and the release of carbide-forming metals from CNT walls. Validating any or all these theories will require further work replicating data, collecting electron micrographs and conducting chemical analyses.
Development of efficient energy materials is critical in order to ease the energy demand and reduce our dependence of fossil fuel. Thermoelectric materials are promising due to their capability of generating electrical power by recovering waste heat. The performance of thermoelectric materials is quantified by a dimensionless figure of merit zT, which depends on their properties such as electrical conductivity, Seebeck coefficient and thermal conductivity. Tetrahedrites, a copper antimony sulfosalt mineral, typified by Cu 12-x MxSb 4 S 13 , where M is a transition metal element such as Ni, Zn, Fe or Mn, have great potential for thermoelectric application due to their relatively high zT (close to 1 at 700 K), earth-abundance, environmental friendliness, favorable electrical properties, and most importantly intrinsic low lattice thermal conductivity (less than 1 W m -1 K -1 ) in wide temperature. In addition to energy recovery, reliable energy storage devices are also emerging to relieve the energy demand and improve the efficiency of consuming energy resources. Lithium-ion batteries are known to be reliable and successful electrochemical energy storage devices and appliable in various aspects, including laptops, smartphones and electrical vehicles. Lithium phosphorous oxynitride (LiPON) are widely used as thin-film solid-state electrolytes in Li-ion battery, which is the only demonstrated solid-state electrolyte that is quite stable in direct contact with Li metal at potentials from 0-5 V. However, the structure of LiPON, the effects of N doping, and the origin of its good electrochemical stability remains inconclusive. In this thesis, reliable modeling techniques accompanied with experimental tools, are applied to study the thermoelectric material tetrahedrite and the ionic conductor LiPON, in order to study their structural and dynamical properties. Accurate and efficient density-functional theory (DFT) and density-functional tight-binding (DFTB) methods, combined with molecular dynamics (MD) simulations are utilized in order to investigate the structures and properties of these energy materials. The incoherent and coherent atomic dynamics study of tetrahedrite Cu 10.5 NiZn 0.5 Sb 4 S 13 provides the origin of softening upon cooling by investigate the motion of Cu12e at different temperatures. The dynamic structure factors in the longitudinal and transverse direction will also be discussed. The Cu movement of Cu-rich tetrahedrite Cu 14 Sb 4 S 13 is revealed by Cu self-diffusivity, nuclear density map and “nudged elastic band” (NEB). Moreover, we investigate the effect of simulation cell size and basis sets on the DFT-based MD simulation results using tetrahedrite Cu1 0 Zn 2 Sb 4 S 13 thermoelectric as a model material, showing the advantage of larger cell by accessing smaller Q range. In addition, the low-temperature structural properties of Cu 12 Sb 4 S 13 is measured by neutron diffraction, which indicates that no cubic to tetragonal transition occurs at metal-semiconductor transition (MST) temperature. Thermoelectric properties such as Seebeck coefficient, electrical resistivity and electrical thermal conductivity will also be investigated. DFTB method is implemented to study the structure and transport properties of Li 3 PO 4 and LiPON, while the exploration of N doping effect is included. Lastly, the LiPON/Li interphase will be revealed in order to study the origin of electrochemical stability.