Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “compositional analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

The composition of gases from a diffusion flame above longleaf pine needle fuel beds

The gas and tar composition of a diffusion flame from longleaf pine needles is currently poorly understood and more data are needed to fill in the gap between pyrolysis data and smoke plume data, thus improving physical and chemical modeling of wildland smoke formation. A pilot experiment to measure light gas and tar composition of such a flame is described for three flame regions: persistent flame (flame base), intermittent flame, and smoke plume. Flame gases from 24 experimental fires were collected in canisters and analyzed using EPA method TO-14A for CO 2 , CO, H 2 , CH 4 , and C 2 to C 7 hydrocarbon gases. Condensed gas (tar) samples were collected and analyzed using GC/MS. Other light gases were measured using FTIR spectroscopy. Results from compositional data analysis suggest significant differences in (relative) concentration of compounds detected in the three regions of the flame. Statistical tests for differences in flame zones were performed using the canister data: Concentration of hydrocarbons relative to CO and CO 2 decreased from the persistent flame zone above the pyrolyzing needles through the intermittent flame region into the flame-free plume. This was likely due to both chemical reactions (oxidation) occurring in the flame as well as the introduction of air into the flame/plume by entrainment.

Biomass↗
DOE OSTI2020

Notch insensitivity in fatigue failure of chopped carbon fiber chip-reinforced composites using experimental and computational analysis

This study focuses on the notch effect on the fatigue failure of chopped carbon fiber chip-reinforced sheet molding compound (SMC) composites by using both experimental and numerical methods. The S-N diagrams of notched specimens are first obtained experimentally, which exhibit large scatter and are shown to depend on the spatial distribution of local fiber orientations. After considering the effect of this spatial distribution by adopting a new fatigue damage parameter to normalize the results, we achieve a much better correlation in the normalized S-N diagram for all the notched specimens with different hole diameters. Next, compared with the fatigue results of smooth specimens without notches, we find that SMC composites under tension-tension fatigue loading exhibit notch-insensitivity, which renders this type of composites a better candidate in joints or similar applications. Meanwhile, the fatigue failure mechanisms of notched SMC composites are explored through a microstructure characterization procedure. On this basis, a computational micromechanics model considering the notch effect and an improved multi-scale progressive damage fatigue law, calibrated by coupon-level fatigue tests of smooth SMC composites under different loading conditions, are employed to predict the fatigue behavior of notched SMC composites. We show that detailed failure processes and fatigue life of notched SMC composites can be efficiently and adequately predicted by this computational framework.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Quaternary Ammonium-Functionalized Poly(Arylene Ether Sulfone) Random Copolymers for Direct Air Capture

Direct air capture (DAC) is a promising tool for reducing CO 2 concentrations in the atmosphere and fighting climate change. We synthesized a series of quaternary ammonium (QA) functionalized poly(arylene ether sulfone) copolymers with varying mole fractions of charge content and demonstrated their potential as sorbents for DAC. Molecular weight analysis determined high monomer conversion was achieved in <6 h and relatively high molecular weights for all copolymer compositions. Thermal analysis revealed all polymers had degradation temperatures >240 °C and a single glass transition temperature (T g ); the T g decreased with an increase in ion exchange capacity (IEC). Fractional free volume and water uptake percentage increased and water contact angle decreased with the number of QA sites when compared to a neutral, commercially available polysulfone (Udel® P-1700 PSU). Next, the novel series of ammonium-functionalized copolymers exhibited a moisture-mediated capture and release of atmospheric CO 2 . When exposed to air containing 30% relative humidity the polymers captured CO 2 and the capacity increased with the IEC. When the relative humidity was increased to 95% the samples released the CO 2 . This study demonstrates a promising CO 2 DAC sorbent and highlights the possibility for continuous DAC with purpose-built free-standing membranes.

42 ENGINEERING↗
DOE OSTI2025

Mesophyll conductance and cell wall composition: insights from a meta‐analysis across species

Mesophyll conductance (g m ) plays a critical role in plant photosynthesis by regulating the diffusion of CO 2 from substomatal cavities to the site of carbon fixation within the chloroplasts. Despite its importance, our understanding of the factors influencing g m , particularly the role of cell wall properties, remains incomplete. In this issue of New Phytologist , Roig-Oliver et al. ( 2025 ; pp. 2384–2391) address this knowledge gap through a comprehensive meta-analysis across multiple species from the major clades of land plants. By analyzing trends in g m and two other key physiological parameters – the ratio of pectin to cellulose and hemicellulose in the cell wall by weight (P/(C + H)), and cell wall thickness (T cw ) – their findings reveal strong correlations of gm with the combination of P/(C + H) and T cw , where g m is directly proportional to P/(C + H) and inversely proportional to T cw . This work not only underscores the influence of cell wall composition on CO 2 diffusion but also provides a valuable framework for further experimental and modeling studies. By shedding light on the dynamic properties of cell walls, shaped by both composition and environmental regulation, this study opens new frontiers for understanding and improving photosynthesis.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2024

Supersonic hot jet ablative testing and analysis of boron nitride nanotube hybrid composites

Boron nitride nanotubes (BNNTs) are high-strength, high-modulus nanotubes with high thermal and oxidative stabilities. Two hybrid composites were prepared with satin weave carbon fiber (CF) and resole-type phenolic resin: one with surface layers of BNNTs and one with alternating interlayers of BNNTs. The samples were subjected to hot jet tests that simulate realistic high-pressure-temperature conditions to understand the behavior of BNNTs under high-pressure erosion. Adding BNNTs to CF/phenolic laminates enhanced the ablation resistance by reinforcing the char material and mitigated localized thermal damage. Hybrid laminates exhibited up to 14% lower weight loss, 55% increase in flexural modulus, higher thermal diffusivity, and improved char yield and microstructure compared to CF/phenolic samples. The surface layer hybrid had many surviving nanotubes reinforcing the char and crystalline oxide structures that could mitigate further oxygen diffusion. Further, various characterization methods were used to deduce possible mechanisms and their products, indicating that BNNTs could serve as growth templates for direct crystalline boron oxide formation. Overall, hybrid BNNT/CF/phenolic laminates displayed better ablation resistance and favorable microstructure evolution under high-pressure conditions.

42 ENGINEERING↗
DOE OSTI2025

Sizing comingled CF/PA 6 fibers with cellulose nanofibrils for enhanced performance properties

Compatibility between the reinforcing phase and the polymer matrix is critical to achieving the desired mechanical and thermal performance of composite materials. Several mechanisms can enhance this interfacial interaction, including surface treatments (e.g., oxidation, plasma, or irradiation), in-situ nanoparticle deposition, and fiber sizing. Here, in this study, cellulose nanofibrils (CNF) were employed as a sustainable sizing agent to modify the interface in commingled carbon fiber (CF)/polyamide 6 (PA 6) yarns, in which CF and PA6 filaments are intimately blended to enable simultaneous consolidation. A 0.25 wt% CNF aqueous suspension was applied under bath sonication to ensure uniform dispersion and minimize agglomeration. CNF-sized and unsized yarns were used to fabricate unidirectional composite plates via filament winding on a flat mandrel, followed by compression molding. Scanning electron microscopy confirmed CNF presence on both CF and PA6 filaments. CNF-sized composites exhibited increments in interlaminar shear strength (ILSS) by 50%, flexural strength by 11%, and tensile strength by 2.5% compared to unsized composites. Thermal analysis showed minimal changes in degradation temperature and crystallinity. These findings demonstrate that CNF sizing enhances interfacial bonding and mechanical performance, offering a scalable and environmentally friendly strategy for thermoplastic composite manufacturing along with yarn/tow handleability.

Cellulose nanofibrils (CNF)↗
DOE OSTI2024

An outbreak of renal failure in asian dogs due to s-triazine adulteration of pet food raw material: Analysis of unique, green kidney stones formed as a result

Renoliths were removed at necropsy from dogs that had died from acute kidney injury in Asia in 2004 and submitted to our laboratories for analysis including elemental composition, mass spectrometry, and microprobe analysis. The presence of a mixed s-triazine matrix comprising melamine, cyanuric acid, and ammelide, but no detectable ammeline, was found in the stone samples we analyzed. The unusual and unique green coloration of these stones was determined to be due to the presence of biliverdin. The occurrence of these green stones distinguished the 2004 incident from another incident in 2007 in the USA and other reported cases. The presence of crystals was reported in renal tubules and collecting ducts in both outbreaks, but no stones were reported in the 2007 incident. Here, this difference suggested a variation in the disease process caused by mixed s- triazine ingestion. Careful monitoring of food additives is warranted to prevent future problems in animals and humans.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2023

Evaluating various composite sampling modes for detecting pathogenic SARS-CoV-2 virus in raw sewage

Inadequate sampling approaches to wastewater analyses can introduce biases, leading to inaccurate results such as false negatives and significant over- or underestimation of average daily viral concentrations, due to the sporadic nature of viral input. To address this challenge, we conducted a field trial within the University of Tennessee residence halls, employing different composite sampling modes that encompassed different time intervals (1 h, 2 h, 4 h, 6 h, and 24 h) across various time windows (morning, afternoon, evening, and late-night). Our primary objective was to identify the optimal approach for generating representative composite samples of SARS-CoV-2 from raw wastewater. Utilizing reverse transcription-quantitative polymerase chain reaction, we quantified the levels of SARS-CoV-2 RNA and pepper mild mottle virus (PMMoV) RNA in raw sewage. Our findings consistently demonstrated that PMMoV RNA, an indicator virus of human fecal contamination in water environment, exhibited higher abundance and lower variability compared to pathogenic SARS-CoV-2 RNA. Significantly, both SARS-CoV-2 and PMMoV RNA exhibited greater variability in 1 h individual composite samples throughout the entire sampling period, contrasting with the stability observed in other time-based composite samples. Through a comprehensive analysis of various composite sampling modes using the Quade Nonparametric ANCOVA test with date, PMMoV concentration and site as covariates, we concluded that employing a composite sampler during a focused 6 h morning window for pathogenic SARS-CoV-2 RNA is a pragmatic and cost-effective strategy for achieving representative composite samples within a single day in wastewater-based epidemiology applications. This method has the potential to significantly enhance the accuracy and reliability of data collected at the community level, thereby contributing to more informed public health decision-making during a pandemic.

sampling timing↗
DOE OSTI2022

Presence of Induced Weak Ferromagnetism in Fe-Substituted YFe x Cr 1–x O 3 Crystalline Compounds

Fe-substituted YFe x Cr 1–x O 3 crystalline compounds show promising magnetic and multiferroic properties. Here we report the synthesis and characterization of several compositions from this series. Using the autocombustion route, various compositions (x = 0.25, 0.50, 0.6, 0.75, 0.9, and 1) were synthesized as high-quality crystalline powders. In order to obtain microscopic and atomic information about their structure and magnetism, characterization was performed using room temperature X-ray diffraction and energy dispersion analysis as well as temperature-dependent neutron diffraction, magnetometry, and 57 Fe Mössbauer spectrometry. Rietveld analysis of the diffraction data revealed a crystallite size of 84 (8) nm for YFeO 3 , while energy dispersion analysis indicated compositions close to the nominal compositions. The magnetic results suggested an enhancement of the weak ferromagnetism for the YFeO 3 phase due to two contributions. First, a high magnetocrystalline anisotropy was associated with the crystalline character that favored a unique high canting angle of the antiferromagnetic phase (13°), as indicated by the neutron diffraction analysis. This was also evidenced by the high magnetic hysteresis curves up to 90 kOe by a remarkable high critical coercivity value of 46.7 kOe at room temperature. Second, the Dzyaloshinskii–Moriya interactions between homogenous and heterogeneous magnetic pairs resulted from the inhomogeneous distribution of Fe 3+ and Cr 3+ ions, as indicated by 57 Fe Mössbauer studies. Together, these results point to new methods of controlling the magnetic properties of these materials.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Signature Analysis Utilizing a Dynamic Molten Salt Reactor Model for MC&A

Moving from traditional fixed fuel nuclear reactor systems to a mobile, dynamic fuel system that has dissolved special nuclear material in a molten salt is a paradigm shift in several respects. One major consideration is how to develop effective nuclear material controls and accounting for these novel reactor systems. The Molten Salt Reactor Experiment is one example of a critical molten salt system and provided a significant reference library based on the documented effort. But it was low thermal power that was not intended to reflect a commercial scale electricity production design. Therefore, to facilitate and assist vendors with domestic licensing considerations, research is underway to identify methods that could be used for domestic safeguards approaches for these novel reactor systems. This research presents the results of a signature analysis of data generated from three simulated scenarios using the molten salt demonstration reactor model defined in the Transient Simulation Framework of Reconfigurable Modules. Each scenario provides 1 hour isotope inventories over a 180 day period. The scenarios investigated provide test cases to examine if direct gamma-ray spectroscopy of the fuel can be used to identify changes comparing a base case (no reactivity control and fixed fission contribution) to an insertion of reactivity (10 pcm no change in fission composition) and a change in fission composition. The analysis demonstrates that monitoring the total count rate in a highly collimated high-resolution photon energy spectrum is sensitive to perturbations imposed into the reactor model. The total photon count rate changes ≈2% for the fission composition change and ≈4.5% for the reactivity insertion compared to the base case. However, both scenarios show an increase in the total photon count rate. The total photon count rate can be used to identify changes due to power (number of fissions) but not due to a change in the material undergoing fission. To distinguish between the two cases of increased power, the photon spectrum would require an intensive analysis technique. A photon peak count rate ratio analysis could be used to identify changes in the fissile material fission generation in the core through identification of a static peak that shows little variation to the source of fission and a highly varying peak. The photon peak strength will ultimately be determined by the isotope’s fission yield. A preliminary analysis investigating the coupling of the isotope’s fission yield and its concentration in the fuel salt derived from the modeling has been performed. A ratio analysis of the photon peak count rates of 140 La to 99 Mo demonstrated that the reactivity insertion creates a distinct difference in the ratio compared to the fission composition change scenario.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2020

Shock initiation of cyclotol (75/25) at both ambient temperature and 70 °C

Here, six shock initiation experiments have been carried out to study the shock sensitivity and develop the unreacted Hugoniot for the Cyclotol composition 75/25 %wt RDX/TNT. The experiments were carried out both at ambient temperature, and elevated to 70 °C, close to the TNT melt temperature of 80 °C. Two sets of three experiments were fired at nominal pressures of 4.1, 6.0 and 7.7 GPa. Comparison has been made to the previously studied (80/20 %wt RDX/TNT) composition and analysis shows that the five percent decrease in RDX content has resulted in a significant increase in shock sensitivity. The increase in initial temperature has yielded an unexpectedly small increase in shock sensitivity, particularly relative to the effects of the compositional change. Wave profiles will be presented, along with a discussion of the unreacted Hugoniot and relative sensitivities presented in the Pop plot.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2022

Alginate–Sodium Sulfate Decahydrate Phase Change Composite with Extended Stability

Here, this study reports on the use of sodium alginate to effectively stabilize sodium sulfate decahydrate (Na 2 SO 4 ∙10H 2 O, SSD) based phase change material (PCM) for application as a thermal energy storage material. Alginate/SSD composite PCMs were prepared by blending SSD with different concentrations of alginate polymer. The resulting composite PCMs demonstrate high phase change enthalpy ~160 J/g and extended cycling stability compared to existing PCM composites. The analysis carried out by optical microscopy, X-ray scattering, and periodic density functional theory (DFT) calculations demonstrated that the stabilization effect was caused by the interplay between ionic and hydrogen bond interactions between the alginate and SSD. Additionally, the variation in mechanical properties of PCM composites with polymer concentrations made it possible to formulate a composite that maintains stable performance after 3D printing. The advanced properties make this composite a promising candidate for application as a thermal energy storage material.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

High-throughput additive manufacturing and characterization of refractory high entropy alloys

Refractory High Entropy Alloys (RHEAs) and Refractory Complex Concentrated Alloys (RCCAs) are high-temperature structural alloys ideally suited for use in harsh environments. While these alloys have shown promising structural properties at high temperatures that exceed the practical limits of conventional alloys, such as Ni-based superalloys, exploration of the complex phase-space of these materials remains a significant challenge. We report on a high-throughput alloy processing and characterization methodology, leveraging laser-based metal additive manufacturing (AM) and mechanical testing techniques, to enable rapid exploration of RHEAs/RCCAs. We utilized in situ alloying and compositional grading, unique to AM processing, to rapidly-produce RHEAs/RCCAs using readily available and inexpensive commercial elemental powders. We demonstrate this approach with the MoNbTaW alloy system, as a model material known for having exceptionally high strength at elevated temperature when processed using conventional methods (e.g., casting). Microstructure analysis, chemical composition, and strain rate dependent hardness of AM-processed material are presented and discussed in the context of understanding the structure-properties relationships of RHEAs/RCCAs.

36 MATERIALS SCIENCE↗
DOE OSTI2020

A cross-sectional aeroelastic analysis and structural optimization tool for slender composite structures

A fully open-source available framework for the parametric cross-sectional analysis and design optimization of slender composite structures, such as helicopter or wind turbine blades, is presented. The framework—Structural Optimization and Aeroelastic Analysis (SONATA)—incorporates two structural solvers, the commercial tool VABS, and the novel open-source code ANBA4. SONATA also parameterizes the design inputs, postprocesses and visualizes the results, and generates the structural inputs to a variety of aeroelastic analysis tools. It is linked to the optimization library OpenMDAO. This work presents the methodology and explains the fundamental approaches of SONATA. Structural characteristics were successfully verified for both VABS and ANBA4 using box beam examples from literature, thereby verifying the parametric approach to generating the topology and mesh in a cross section as well as the solver integration. The framework was furthermore exercised by analyzing and evaluating a fully resolved highly flexible wind turbine blade. Computed structural characteristics correlated between VABS and ANBA4, including off-diagonal terms. Stresses, strains, and deformations were recovered from loads derived through coupling with aeroelastic analysis. The framework, therefore, proves effective in accurately analyzing and optimizing slender composite structures on a high-fidelity level that is close to a three-dimensional finite element model.

42 ENGINEERING↗
DOE OSTI2021

Evidence of an oxidation induced phase transformation for a delta phase plutonium-gallium alloy

The oxidation of an ~1.5 at% Ga plutonium metal alloy in dry air as a function of time was studied using a combination of FIB-SEM, AES, and XRD. Analysis of SEM images of FIB cross-sections of the oxide allowed for direct measurement of the oxide thickness as well as determination of heterogeneity in the extent of the oxide. AES analysis performed on cross-sections of the oxide allowed for quantitative analysis of the atomic composition and semi-quantitative analysis of the chemical composition. Initial preparation of the sample was found to induce a martensitic transformation to α' - Pu with an average thickness of 233 nm. Electropolishing was found to be sufficient to fully remove the α' layer with creation of only a minimum oxide layer. Growth of the oxide in dry air was found to initially follow parabolic kinetics, with a parabolic rate constant orders of magnitude higher than expected for δ-Pu but in-line with values extrapolated to room temperature for α-Pu. Following complete oxidation of the initial α` layer, further regions of plutonium metal depleted in gallium were observed to form at the oxide / metal interface. However, gallium, as Ga 2 O 3 , was found to be enriched at the surface and present in the oxide in an amount comparable to the relative Ga:Pu ratio of the bulk metal alloy. Finally, the results presented here serve to bridge a diverse array of previous experimental and theoretical data and provide the first comprehensive view of the fate of the δ-stabilizer during formation of an oxide.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Adhesion and tribological characteristics of modified polyurethane coating on composite substrate

In the present study, glass-epoxy composites were used as a substrate to study the performance of modified polyurethane coating. Two-layer coating (180–200 µm) wherein the epoxy primer as the first coat and polyurethane as the top coat was applied using an air-assisted spray gun to increase the service life of the composite. The analysis of coating was performed using gloss, contact angle, FTIR, TGA, tensile test and SEM. The bonding strength between coating and substrate was evaluated by cross-hatch cut, 180 deg peel strength and pull-off adhesion tests. Scratch, Taber abrasion and Pin-on-disc tests were also performed to evaluate the wear resistance. In addition, a rain erosion test was performed to check the stability of the coating. From the above tests, it is concluded that the applied coating well adhered to the composite substrate. The data generated from different tests can be used to estimate the service life of polymer composites and coatings.

Mushtaq, Mohammed↗
DOE OSTI2025

Near-infrared spectroscopy as a green analytical tool for sustainable biomass characterization for biofuels and bioproducts: An overview

Biomass, a widely used renewable energy source, requires characterization to optimize biofuel and bioproduct processes, customize feedstocks, and ensure economic and environmental sustainability. Conventional wet-chemistry methods for biomass analysis are slow, expensive, and require significant reagents and skilled personnel. In contrast, near-infrared (NIR) spectroscopy, a faster, cost-effective, and reagent-free green technology, enables non-destructive biomass analysis with minimal sample preparation. This study provides an overview of the fundamentals of NIR spectroscopy and explores its recent applications for analyzing various biomass properties important to the biofuel and bioproduct industry. The study also critically evaluates the challenges and opportunities of using NIR spectroscopy for biomass analysis. This review aims to guide future research for rapid and high throughput characterization of biomass in the biomass industry, supporting the United Nations’ sustainable development goal (SDG) 7: producing affordable and sustainable energy.

Biofuels↗