Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “coating”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Environmental degradation of electroplated nickel and copper coated SS316H in molten FLiNaK salt

Corrosion of nickel and copper electroplated coatings on SS316H in molten FLiNaK salt was studied. 500- and 1000-hour static corrosion tests were performed in molten FLiNaK at 700 degrees Celsius. Characterization of the coatings following corrosion indicated that they did not degrade in the molten salt during the corrosion experiment and fully protected the underlying SS316H from chromium dissolution. Interdiffusion between the copper coating and SS316H was extremely limited, interdiffusion between the nickel coating and SS316H. Diffusion modelling revealed that the nickel coatings still significantly reduced chromium dissolution over 60 years despite the interdiffusion.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Fractal coatings of Ni and NiYSZ for high-temperature corrosion mitigation in solar salt

This paper introduces a novel approach to corrosion mitigation using electrodeposited, fractal Ni and NiYSZ coatings. Highly adherent, durable multiscale coatings with fractal dimensions above 1.80 were fabricated. Corrosion characteristics of coated plain and etched surfaces of In800H, SS310, SS316 and SS347, in comparison to Ha230, were studied in molten 60% NaNO 3 + 40% KNO 3 at 600 °C. The corrosion rate of coated Fe-based alloys reduced by up to 68% compared to uncoated alloys and was on par with or lower than the corrosion rate of Ha230. Furthermore, the corrosion-resistant coatings provide for use of low-cost alloys in high temperature corrosive environments.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Measurement of High-temperature Thermophysical Properties of Bulk and Coatings Using Modulated Photothermal Radiometry

This paper presents the development of instrumentation for the measurement of high-temperature thermal conductivity of bulk and coatings using a modulated photothermal radiometry (MPR) method, where a sample is heated by an intensity-modulated laser to probe into different layers of the sample. While MPR has been previously established, most of the previous studies only focus on the measurement at room temperature. The MPR has not been well studied for measurements of bulk and coating materials at high temperatures, which are increasingly important for a multitude of applications, such as materials used in the concentrating solar power (CSP) plants and the nuclear reactors. MPR is a non-contact technique that utilizes the intrinsic thermal emission from the specimens for thermometry, which is favorable for measurements at high temperatures in harsh environment. The authors designed and utilized a sample holder suitable for high temperature measurement up to 973 K with good temperature uniformity within the sample. The high-temperature MPR setup was validated by measuring bulk materials with known thermal conductivity. The setup and technique were then extended to the measurement of black solar-absorbing coatings of 10 to 50 μm thick on various substrates by modulating the frequency of the laser heating beam and the thermal penetration depth. Here, the studies showed that thermal conductivities of typical solar-absorbing coatings are 0.4 ~ 0.8 W m -1 K -1 , indicating a possibly large temperature drop within the coating under high solar irradiation flux, such as over 1000-sun for central solar towers in CSP plants.

14 SOLAR ENERGY↗
DOE OSTI2023

Development of hydrothermal corrosion model and BWR metal coating for CVD SiC in light water reactors

SiC/SiC fiber composites with CVD SiC overcoats are potential candidates for light water reactor advanced accident tolerant cladding materials. Understanding its corrosion kinetics in Light Water Reactor (LWR) conditions is essential to evaluate the concept's viability. Existing models only account for the temperature and oxygen concentration effect on the hydrothermal corrosion behavior applicable to LWR operating conditions. However, the development of a general corrosion rate for CVD SiC that accounts for the impact of irradiated microstructure, flow rate, electrical resistivity, pH, and surface roughness is critical for the practical realization of SiC/SiC-based cladding concepts. After a rigorous experimental campaign, this work updates the existing hydrothermal corrosion model to predict hydrothermal corrosion in LWRs. Numerical radiation and coolant chemistry analysis for LWRs conducted based on the updated corrosion kinetic models suggests that CVD SiC is likely a viable environmental barrier coating for Pressurized Water Reactors while questionable for Boiling Water Reactors (BWR) when the effect of irradiation damage on SiC corrosion is considered. An effective mitigation strategy for the double-layer metal coating is proposed for BWR applications. The double-layer metal coating comprising a FeCrAl overcoat with an intermediate Cr bond coating was observed to provide a stable protective barrier against SiC dissolution in BWR conditions. Finally, the proposed metal coating was also fully adherent following quench and burst tests.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Al 2 O 3 /TiO 2 coated separators: Roll-to-roll processing and implications for improved battery safety and performance

Heat generation is one of the major concerns with lithium-ion batteries (LIB) while charging them at higher currents, which could inadvertently impact the rate performance and reduce the safety of the cell. Polymer separator is one of the least thermal conductive components of a LIB. In addition, commercial separators for LIB are made from polyolefin membranes that tend to shrink and curl at higher temperatures due to their lower melting temperature (~130 °C). Developing separators with improved thermal stability and higher electrolyte uptake is essential for enhancing the safety as well as the performance of the LIB. In this work, a thin layer of ceramic coatings (Al 2 O 3 and TiO 2 ) is applied on propylene (PP) membrane to improve the thermal stability and electrolyte affinity without compromising the rate performance. A slurry with 100% Al 2 O 3 coated on the polypropylene separator exhibited the best improvement in thermal stability ( shrinkage of 0.6% vs 6.0% for uncoated membrane) and excellent rate performance with 92% capacity retention at 2C. The Al 2 O 3 coated separator demonstrated excellent electrolyte wettability compared to the uncoated membrane. The cross-plane thermal conductivity of the ceramic coated separators is analyzed to understand their heat transfer behavior. The thermal conductivity of the separator is improved by ~3.2 times with the Al 2 O 3 coating.

25 ENERGY STORAGE↗
DOE OSTI2021

An improved oxygen reduction reaction activity and CO 2 -tolerance of La 0.6 Sr 0.4 Co 0.2 Fe 0.8 O 3-δ achieved by a surface modification with barium cobaltite coatings

Solid oxide fuel cells (SOFCs) cathode often suffers from the poisoning effect of the contaminants commonly encountered in air such as CO 2 . Here we report an effective approach to enhancing the activity and CO 2 tolerance of the state-of-the-art La 0.6 Sr 0.4 Co 0.2 Fe 0.8 O 3-δ (LSCF) cathode enabled by a coating of BaCoO 3-δ (BCO), as verified by the electrochemical testings, Raman analyses, and density functional theory calculations. When surface modified with a thin-film BCO coating, LSCF displays a much enhanced ORR activity and an improved durability against CO 2 . For example, anode supported SOFCs with the LSCF cathode coated with BCO coatings show a remarkable peak power density (Pmax) of 0.41 Wcm -2 and a significantly reduced degradation rate in current density of ~0.08% h -1 at 0.8 V and 700 °C for a period of 300 hs when humidified H2 (with 3 vol%H2O) was used as fuel and air with 8 vol% CO 2 as oxidant. The demonstrated performance is improved when compared with those of the cells with a blank LSCF electrode (a Pmax of ~0.36 Wcm -2 and a degradation rate of ~0.15% h -1 ) under the same conditions. Furthermore, the adsorption energy calculations suggests that BCO coating makes CO 2 adsorption much weaker than LSCF (-0.54 eV versus -1.07 eV).

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2021

High temperature fracture toughness of single-layer CrAlN and CrAlSiN hard coatings

Hardness and toughness are among of the most important physical properties of hard coatings and it is important to analyze them at temperatures present during coating applications. CrAlN and CrAlSiN are hard coating materials frequently used in high temperature applications. Here, while both possess high oxidation resistance and thermal stability, they differ in their microstructure. In this work, the fracture toughness of magnetron-sputtered single-layer CrAlN and CrAlSiN hard coatings was determined up to 700 °C by in-situ scanning electron microscopy micro-cantilever deflection tests. The results show a decreasing trend of the fracture toughness with increasing temperature. While both coatings' fracture toughness trends are similar up to 400 °C, they diverge at higher temperatures. In general, the evolution of the fracture toughness with increasing temperature shows similarities to the observed changes in hardness in the same temperature range.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Conditioning the Surface and Bulk of High-Nickel Cathodes with a Nb Coating: An In Situ X-ray Study

Surface coating is commonly employed by industries to improve the cycling and thermal stability of high-nickel (Ni) transition metal (TM) layered cathodes for their practical use in lithium-ion batteries. Niobium (Nb) coating or substitution has been shown to be effective in stabilizing LiNi 0.8 Mn 0.1 Co 0.1 O 2 (NMC811) cathodes; in addition, the electrochemical performance of the final products varies depending on the postprocessing. In this follow-up study, we use in situ synchrotron X-ray diffraction to investigate the kinetic processes and the involved structural evolution in Nb-coated NMC811 upon heat treatment. Furthermore, quantitative structure analysis reveals thermally driven concurrent changes in the bulk and surface, in particular, the phase evolution of the coating layer and Nb/TM interdiffusion that facilitates penetration of Nb into the bulk and particle growth at the increased temperatures. Findings from this study highlight the new opportunities for the intended control of the structure and surface properties of high-Ni cathodes through surface coating in conjunction with postprocessing.

36 MATERIALS SCIENCE↗
DOE OSTI2023

High-Temperature Air Stability of Electrodeposited Copper Cobalt Oxide and Copper Manganese Oxide Absorber Coatings for Concentrating Solar Power

The solar absorptance of a thermal receiver surface significantly affects the photothermal conversion efficiency of concentrating solar power (CSP) plants. The stability of solar receivers and coatings applied to improve solar absorptance at high temperatures is critical for efficient and long-term operation. This study analyzes the high-temperature air stability of multiscale fractal textured electrodeposited copper manganese oxide and copper cobalt oxide solar receiver coatings over a range of temperatures. The study also investigates the effect of high temperature on phase stability, chemical and morphological evolution, and the optical properties of the two solar absorber materials. A computational model is developed to determine the absorptance of the textured absorbers and is shown to match the experimental measurements closely over a range of heat treatment temperatures from 450 °C to 850 °C and durations up to 100 h. Degradation curves and coating stability maps are developed from the study. Copper manganese oxide and copper cobalt oxide coatings exhibit good thermal stability up to ~815 °C and 630 °C, respectively, with minimal changes in their optical and structural properties with thermal efficiency greater than 90%. Furthermore, the study offers valuable insights into the high-temperature annealing effects on the optical and structural properties of multiscale copper alloyed coatings fabricated by electrodeposition and presents a means of designing the optimal temperature range for maximizing absorber efficiency in practical applications.

14 SOLAR ENERGY↗
DOE OSTI2022

Spinel Cu–Mn–Cr Oxide Nanoparticle-Pigmented Solar Selective Coatings Maintaining >94% Efficiency at 750 °C

High-temperature concentrating solar power (CSP) system is capable of harvesting and storing solar energy as heat towards cost-effective dispatchable solar electricity. Solar selective coating is a critical component to boost its efficiency by maximizing solar absorptance and minimizing thermal emittance losses. However, maintaining a high solar-thermal conversion efficiency >90% for long-term operation at ≥750 ºC remains a significant challenge. Herein, we report spray-coated spinel Cu-Mn-Cr oxide nanoparticle-pigmented solar selective coatings on Inconel tube sections maintaining ≥94% efficiency at 750 ºC and ≥92.5% at 800 ºC under 1000x solar concentration after 60 simulated day-night thermal cycles in air, each cycle comprising 12h at 750 ºC/800 ºC and 12h cooling to 25 ºC. The solar spectral selectivity is intrinsic to the band-to-band and d-d transitions of non-stoichiometric spinel Cu-Mn-Cr oxide nanoparticles. Furthermore, this feature offers a large fabrication tolerance in nanoparticle volume fraction and coating thickness, facilitating low-cost and scalable spray-coated high-efficiency solar selective absorbers for high-temperature CSP systems.

14 SOLAR ENERGY↗
DOE OSTI2022

Conformal PEDOT Coating Enables Ultra-High-Voltage and High-Temperature Operation for Single-Crystal Ni-Rich Cathodes

Single-crystal Ni-rich Li[Ni x Mn y Co 1-x-y ]O 2 (SC-NMC) cathodes represent a promising approach to mitigate the cracking issue of conventional polycrystalline cathodes. However, many reported SC-NMC cathodes still suffer from unsatisfactory cycling stability, particularly under high charge cutoff voltage and/or elevated temperature. Herein, we report an ultraconformal and durable poly(3,4-ethylenedioxythiophene) (PEDOT) coating for SC-NMC cathodes using an oxidative chemical vapor deposition (oCVD) technique, which significantly improves their high-voltage (4.6 V) and high-temperature operation resiliency. The PEDOT coated SC LiNi 0.83 Mn 0.1 Co 0.07 O 2 (SC-NMC83) delivers an impressive capacity retention rate of 96.7% and 89.5% after 100 and 200 cycles, respectively. Significantly, even after calendar aging at 45 degrees C and 4.6 V, the coated cathode can still retain 85.3% (in comparison with 59.6% for the bare one) of the initial capacity after 100 cycles at a 0.5 C rate. Synchrotron X-ray experiments and interface characterization collectively reveal that the conformal PEDOT coating not only effectively stabilizes the crystallographic structure and maintains the integrity of the particles but also significantly suppresses the electrolyte's corrosion, resulting in improved electrochemical/thermal stability. Our findings highlight the promise of an oCVD PEDOT coating for single-crystal Ni-rich cathodes to meet the grand challenge of high-energy batteries under extreme conditions.

25 ENERGY STORAGE↗
DOE OSTI2021

Tribocatalytically-activated formation of protective friction and wear reducing carbon coatings from alkane environment

Minimizing the wear of the surfaces exposed to mechanical shear stresses is a critical challenge for maximizing the lifespan of rotary mechanical parts. In this study, we have discovered the anti-wear capability of a series of metal nitride-copper nanocomposite coatings tested in a liquid hydrocarbon environment. The results indicate substantial reduction of the wear in comparison to the uncoated steel substrate. Analysis of the wear tracks indicates the formation of carbon-based protective films directly at the sliding interface during the tribological tests. Raman spectroscopy mapping of the wear track suggests the amorphous carbon (a-C) nature of the formed tribofilm. Further analysis of the tribocatalytic activity of the best coating candidate, MoN-Cu, as a function of load (0.25–1 N) and temperature (25 °C and 50 °C) was performed in three alkane solutions, decane, dodecane, and hexadecane. Results indicated that elevated temperature and high contact pressure lead to different tribological characteristics of the coating tested in different environments. The elemental energy dispersive x-ray spectroscopy analysis and Raman analysis revealed formation of the amorphous carbon film that facilitates easy shearing at the contact interface thus enabling more stable friction behavior and lower wear of the tribocatalytic coating. These findings provide new insights into the tribocatalysis mechanism that enables the formation of zero-wear coatings.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Polymer-derived SiC/C/Al environmental barrier coatings on carbon steel

Carbon steel is a widely used structural material; however, it lacks corrosion resistance in water environments. An alternative approach to overcome this challenge is to implement the deposition of inherently corrosion-resistant ceramic coatings. SiC/C/Al coatings were developed at 700°C, using polycarbosilane in combination with Al and C, which were included as active and passive fillers, respectively. Here, we show that it is necessary to use Al particle sizes below 10 µm for them to function as an active filler below 900°C. Owing to their laminar microstructure, these coatings showed a cohesive delamination with an adhesion strength of 10 MPa. Results demonstrated that these coatings were able to reduce the corrosion of carbon steel in saline water by 99.7%, with corrosion rates of 38.33 mpy for carbon steel, and 0.099 and 0.155 mpy for SiC/C and SiC/C/Al (10 µm) coatings, respectively.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Spray-Coated Silver as Backside Metal for III–V Photovoltaic Devices on GaAs and Ge Substrates

The accelerated increase in demand for III-V space photovoltaics on GaAs and Ge substrates, as well as growing interests in terrestrial applications, motivate the development of cost-effective, high-throughput processing routes of these materials. Here, in this study, we assess spray-coated silver (Ag) back contact metallization as a substitute for electron-beam-evaporated metals currently used in industry. We find that the spray-coated Ag films are dense and continuous. By means of quantum efficiency, dark current-voltage, and illuminated current-voltage characterizations, we show that spray-coated GaAs and Ge solar cells perform similarly to baseline devices with electroplated Au, including under high current densities. We estimate that the thresholds for specific contact resistance below which back contacts do not significantly contribute to resistive loss are 2.1 x 10 -1 Ω•cm 2 for GaAs and 4.7 x 10 -2 Ω•cm 2 for Ge. We experimentally confirm that our spray-coated samples meet these requirements. Peel tests show that the adhesion of plain spray-coated Ag films to the back of p-type Ge substrates used in III-V solar cells is currently insufficient, whereas adhesion to p-type GaAs substrates is outstanding and requires no further optimization.

14 SOLAR ENERGY↗
DOE OSTI2021

Laser-Interference Surface Preparation for Enhanced Coating Adhesion and Adhesive Joining of Multi-Materials (Final Project Report)

This report investigates a laser-interference surface treatment as a non-contact, i.e., without major solid/liquid medium application or abrasion, and non-chemical surface preparation method for aerospace coating systems. It was proposed to use the laser-interference technique to structure surfaces of Al and/or Ti, creating "rough" surfaces with pre-engineered series of ridges and valleys at submicron scale. The science goal of this study was to develop an understanding of the surface microstructure, topology, and physical mechanisms that would improve adhesion and corrosion protection of Al2024-T3. Microstructure analysis indicates that the laser-interference structuring (LIS) was found to reduce the formation of CuMn-rich precipitates in Al 2024-T3 over a 500-800 nm depth from top surface. The X-cut and cross-hatch coating adhesion ratings indicate that the LIS specimens meet the performance requirements in the coating adhesion specifications by having a higher or identical ranking to those specimens prepared with current state-of-the-art chemical conversion or sulfuric acid anodizing. After the ASTM B117 corrosion exposure, it was found that the laser processed specimens exhibited only few blisters. It was found that the corrosion damage was minimized at a laser rastering speed of 4 mm/s, for which only 33% of specimens developed very minor corrosion damage. The ASTM D1654 creepage ratings, used to evaluate corrosion damage along the scribe lines, were found to be at least nine for all coated panels. These results indicate that the laser-interference technique with the additional acetone wiping has the potential to be further developed as a minor chemical surface preparation technique for chromate-containing epoxy primers coatings.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Safety Analysis of Chromium-Coated Accident-Tolerant Fuels with Increased Enrichment and Extended Burnup [Slides]

This report documents research and development conducted in support of deployment of accident-tolerant fuels. Specifically, the performance of chromium coating during a beyond design basis accident was investigated. An 18m reference core was considered, and the performance of cases with and without chromium coating compared. An extended cycle length of 24m was then considered with the chromium coating, to determine if the benefit of using the chromium coating was more or less significant than the increased fission product inventory when considering fission product release. The chromium coating model utilized here is a preliminary implementation and further work is recommended on a more detailed model.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Advanced Coating Compositions and Microstructures to Improve Uptime and Operational Flexibility in Cyclic, Low-Load Thermal Utility Plants

GE, the University of Tennessee, and Oak Ridge National Laboratory collaborated from 2020 to 2023 developing two key technologies for improving the viability of fuel switching and load following in thermal utility plants: a) cost-effective weld overlay compositions for boiler tubing b) cathodic arc coatings that deliver improvements in both erosion resistance and oxidation resistance in high temperature steam for HP turbine blades The team worked through a robust, logical project map to de-risk these two technologies and advance them from TRL 3 to TRL 6. For the cost-effective weld overlay, the team developed a ferritic filler material which was fabricated at a vendor for 18% the average market cost of Inconel 625 wire, had a corrosion rate 3x lower in conditions simulating a biomass-fired superheater and 10x lower in conditions simulating a coal-fired superheater, and was fabricated into prototype overlaid tubing that passed ASME requirements including transverse bending, dye penetrant inspection, and ASTM G-76 evaluation. For the cathodic arc coatings applied to steam turbine blades, the team developed a novel composition that was successfully transferred to a qualified vendor. The vendor was able to produce coated prototypes with 4x the as-deposited erosion resistance and 10.4x the post-steam-exposure erosion resistance of the TiN coating the vendor currently applies on GE steam turbine components, without significantly increasing process cost. These coated prototypes also passed a GE inspection and showed favorable performance in high temperature erosion, nanoindentation, sliding wear, scratch adhesion, and high cycle fatigue testing. If successfully deployed by GE, it is anticipated that the technologies will enable the following: • 25%-50% increase in time between outages for both boilers and HP turbines. • 50% decrease in cost for weld overlay on a per foot basis relative to todays NiCr alloys. • Adequate oxidation resistance and erosion for HP turbine inlet steam at >620°C and >220 bar. • No need for changes in component supply chain or any notable Capital Expenditures. 5 Decreasing component cost, increasing performance, and extending time between outages represent direct value propositions to GE and their customers. For the American consumer, these objectives translate into increased grid reliability (fewer unexpected outages), decreased Levelized Cost of Electricity, and improved environmental health (low-loading/load following to accelerate penetration of renewables). The results also have implications for wear resistant tooling, wire arc additive manufacturing, more durable components for syngas cleanup, and deployment of more efficient thermochemical pathways for carbon negative fuel production

09 BIOMASS FUELS↗
DOE OSTI2022

Comprehensive Evaluation for Protective Coatings: Optical, Electrical, Photoelectrochemical, and Spectroscopic Characterizations

Numerous efficient semiconductors suffer from instability in aqueous electrolytes. Strategies utilizing protective coatings have thus been developed to protect these photoabsorbers against corrosion while synergistically improving charge separation and reaction kinetics. Recently, various photoelectrochemical (PEC) protective coatings have been reported with suitable electronic properties to ensure low charge transport loss and reveal the fundamental photoabsorber efficiency. However, protocols for studying the critical figures of merit for protective coatings have yet to be established. For this reason, we propose four criteria for evaluating the performance of a protective coating for PEC water-splitting: stability, conductivity, optical transparency, and energetic matching. We then propose a flow chart that summarizes the recommended testing protocols for quantifying these four performance metrics. In particular, we lay out the stepwise testing protocols to evaluate the energetics matching at a semiconductor/coating/(catalyst)/liquid interface. Finally, we provide an outlook for the future benchmarking needs for coatings.

36 MATERIALS SCIENCE↗