Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “clip”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
NASA NTRS1978

The practical application of a finite difference method for analyzing transonic flow over oscillating airfoils and wings

Separating the velocity potential into steady and unsteady parts and linearizing the resulting unsteady equations for small disturbances was performed. The steady velocity potential was obtained first from the well known nonlinear equation for steady transonic flow. The unsteady velocity potential was then obtained from a linear differential equation in complex form with spatially varying coefficients. Since sinusoidal motion is assumed, the unsteady equation is independent of time. The results of an investigation into the relaxation-solution-instability problem was discussed. Concepts examined include variations in outer boundary conditions, a coordinate transformation so that the boundary condition at infinity may be applied to the outer boundaries of the finite difference region, and overlapping subregions. The general conclusion was that only a full direct solution in which all unknowns are obtained at the same time will avoid the solution instabilities of relaxation. An analysis of the one-dimensional form of the unsteady transonic equation was studied to evaluate errors between exact and finite difference solutions. Pressure distributions were presented for a low-aspect-ratio clipped delta wing at Mach number of 0.9 and for a moderate-aspect-ratio rectangular wing at a Mach number of 0.875.

Weatherill, W. H.↗
NASA NTRS1978

Magnetometer with a miniature transducer and automatic scanning

The magnetometer is based on the time variation of the magnetic permeability in the magnetic material of its transducer; however, its operation is substantially different from the ordinary flux-gate magnetometer. The transducer uses 0.05 mm diameter plated magnetic wire and is made flat enabling it to make measurements of transverse magnetic fields as close as 0.08 mm from the surface, and it has very good spatial resolution because of its small active region of approximately 0.64 mm by 0.76 mm. The magnetometer uses an inexpensive clip-on millimeter for driving and processing the electrical signals and readout. It also utilizes an automatic scanning technique which is made possible by a specially designed transducer holding mechanism that replaces the ink pen on an X-Y recorder.

Debnam, W. J. J.↗
NASA NTRS1978

Evaluation of a locally homogeneous model of spray evaporation

Measurements were conducted on an evaporating spray in a stagnant environment. The spray was formed using an air-atomizing injector to yield a Sauter mean diameter of the order of 30 microns. The region where evaporation occurred extended approximately 1 m from the injector for the test conditions. Profiles of mean velocity, temperature, composition, and drop size distribution, as well as velocity fluctuations and Reynolds stress, were measured. The results are compared with a locally homogeneous two-phase flow model which implies no velocity difference and thermodynamic equilibrium between the phases. The flow was represented by a k-epsilon-g turbulence model employing a clipped Gaussian probability density function for mixture fraction fluctuations. The model provides a good representation of earlier single-phase jet measurements, but generally overestimates the rate of development of the spray. Using the model predictions to represent conditions along the centerline of the spray, drop life-history calculations were conducted which indicate that these discrepancies are due to slip and loss of thermodynamic equilibrium between the phases.

Shearer, A. J.↗
NASA NTRS1979

Eye-controlled switch

Eye motion sensor clipped to standard eyeglass frame and circuit allows electric wheel chair to be controlled by eye movements alone.

Walker, G. L.↗
NASA NTRS1979

Displacement gage modified for multiple measurements

Clip-in gages used in fracture toughness testing are modified to permit acquisition of additional displacement data. With innovation, displacement is measured simultaneously at several locations on face of test specimen.

Buzzard, R. J.↗
NASA NTRS1978

Study of aerodynamic technology for VSTOL fighter/attack aircraft: Vertical attitude concept

The aerodynamic technology for a vertical attitude VSTOL (VATOL) supersonic fighter/attack aircraft was studied. The selected configuration features a tailless clipped delta wing with leading-edge extension (LEX), maneuvering flaps, top-side inlet, twin dry engines and vectoring nozzles. A relaxed static stability is employed in conjunction with the maneuvering flaps to optimize transonic performance and minimize supersonic trim drag. Control for subaerodynamic flight is obtained by gimballing the nozzles in combination with wing tip jets. Emphasis is placed on the development of aerodynamic characteristics and the identification of aerodynamic uncertainties. A wind tunnel test program is proposed to resolve these uncertainties and ascertain the feasibility of the conceptual design. Ship interface, flight control integration, crew station concepts, advanced weapons, avionics, and materials are discussed.

Gerhardt, H. A.↗
NASA NTRS1976

Portable electrophoresis apparatus using minimum electrolyte

An electrophoresis unit for use in conducting electrophoretic analysis of specimens is described. The unit includes a sealable container in which a substrate mounted specimen is suspended in an electrolytic vapor. A heating unit is employed to heat a supply of electrolyte to produce the vapor. The substrate is suspended within the container by being attached between a pair of clips which also serve as electrodes to which a direct current power source may be connected.

Stevens, M. R.↗
NASA NTRS1978

The behavior of superfluid helium in zero gravity

Studies of the behavior of superfluid helium in zero gravity including fluid distribution within the cryostat, thickness of superfluid films, and heat transfer in such films, were conducted in one gravity in the laboratory and in zero-g flights on aircraft and sounding rocket. The studies show that the bulk motions are sufficiently well damped to allow control of their effects on experiments and spacecraft attitude control systems, and that the superfluid films will be able to maintain the high degree of temperature uniformity found in laboratory superfluid helium cryostats. The presentation includes film clips of the motions on the superfluid in zero-g.

Mason, P.↗
NASA NTRS1979

Man and machine design for space flight

The factors involved in creating effective designs for living and working in a weightless environment are discussed. Among the areas covered are special provisions for eating and drinking, a special shower nozzle to remove soap, electric shavers designed for vacuum containment of the clippings, and the need for restraint systems at the crew's workstations. Attention is given to the fact that the crewmen assume a neutral body posture in weightlessness which is an important consideration in designing displays, controls, and windows. It is concluded that the incorporation of the change in body posture and the requirement for restraint into future designs will greatly facilitate the crewman's task in the weightless environment.

Louviere, A. J.↗
NASA NTRS1980

Tension-mode loading for bend specimens in cryogens

Special fixture permits use of tension-loading apparatus in fracture-toughness tests on standard bend specimens. Specimen is held in place by spacer blocks and wire clips. Central, load-application roller bends specimen between lateral, reaction-load rollers.

Pierce, W. S.↗
NASA NTRS1980

Design and fabrication of titanium multi-wall Thermal Protection System (TPS) test panels

A titanium multiwall thermal protection system panel was designed. The panel is a nine sheet sandwich structure consisting of an upper and lower face sheet; four dimpled sheets, three septum sheets, and clips for attachment to a vehicle structure. An acceptable fabrication process was developed, and the panel design was verified through mechanical and thermal testing of component specimens. A design was completed which takes into consideration fabrication techniques, thermal properties, mechanical properties, and materials availability.

Blair, W.↗
NASA NTRS1980

Study of curved glass photovoltaic module and module electrical isolation design requirements

The design of a 1.2 by 2.4 m curved glass superstrate and support clip assembly is presented, along with the results of finite element computer analysis and a glass industry survey conducted to assess the technical and economic feasibility of the concept. Installed costs for four curved glass module array configurations are estimated and compared with cost previously reported for comparable flat glass module configurations. Electrical properties of candidate module encapsulation systems are evaluated along with present industry practice for the design and testing of electrical insulation systems. Electric design requirements for module encapsulation systems are also discussed.

Source record↗
NASA NTRS1980

Detection of individual atoms in helium buffer gas and observation of their real-time motion

Single atoms are detected and their motion measured for the first time to our knowledge by the fluorescence photon-burst method in the presence of large quantities of buffer gas. A single-clipped digital correlator records the photon burst in real time and displays the atom's transit time across the laser beam. A comparison is made of the special requirements for single-atom detection in vacuum and in a buffer gas. Finally, the probability distribution of the bursts from many atoms is measured. It further proves that the bursts observed on resonance are due to single atoms and not simply to noise fluctuations.

Pan, C. L.↗
NASA NTRS1980

Interactive display of molecular models using a microcomputer system

A simple, microcomputer-based, interactive graphics display system has been developed for the presentation of perspective views of wire frame molecular models. The display system is based on a TERAK 8510a graphics computer system with a display unit consisting of microprocessor, television display and keyboard subsystems. The operating system includes a screen editor, file manager, PASCAL and BASIC compilers and command options for linking and executing programs. The graphics program, written in USCD PASCAL, involves the centering of the coordinate system, the transformation of centered model coordinates into homogeneous coordinates, the construction of a viewing transformation matrix to operate on the coordinates, clipping invisible points, perspective transformation and scaling to screen coordinates; commands available include ZOOM, ROTATE, RESET, and CHANGEVIEW. Data file structure was chosen to minimize the amount of disk storage space. Despite the inherent slowness of the system, its low cost and flexibility suggests general applicability.

Egan, J. T.↗
NASA NTRS1982

Multiwall thermal protection system

Multiwall insulating sandwich panels are provided for thermal protection of hypervelocity vehicles and other enclosures. In one embodiment, the multiwall panels are formed of alternate layers of dimpled and flat metal (titanium alloy) foil sheets and beaded scarfed edge seals to provide enclosure thermal protection up to 1000 F. An additional embodiment employs an intermediate fibrous insulation for the sandwich panel to provide thermal protection up to 2000 F. A third embodiment employs a silicide coated columbium waffle as the outer panel skin and fibrous layered intermediate protection for thermal environment protection up to 2500 F. The use of multiple panels on an enclosure facilitate repair and refurbishment of the thermal protection system due to the simple support provided by the tab and clip attachment for the panels.

Jackson, L. R.↗
NASA NTRS1981

The effect of temperature fluctuations of reaction rate constants in turbulent reacting flows

Current models of turbulent reacting flows frequently use Arrhenius reaction rate constants obtained from static or laminar flow theory and/or experiments, or from best fits of static, laminar, and turbulent data. By treating the reaction rate constant as a continuous random variable which is temperature-dependent, the present study assesses the effect of turbulent temperature fluctuations on the reaction rate constant. This model requires that a probability density function (PDF) describing the nature of the fluctuations be specified. Three PDFs are examined: the clipped Gaussian, the beta PDF, and the ramp model. All the models indicate that the reaction rate constant is greater in a turbulent flow field than in an equivalent laminar flow. In addition, an amplification ratio, which is the ratio of the turbulent rate constant to the laminar rate constant, is defined and its behavior as a function of the mean temperature fluctuations is described

Chinitz, W.↗
NASA NTRS1982

Subsonic aerodynamic and flutter characteristics of several wings calculated by the SOUSSA P1.1 panel method

Several applications of the steady, oscillatory, and unsteady subsonic and supersonic aerodynamics (SOUSSA) computer program to wings with steady and oscillatory motion, including flutter, are discussed. The program employs a generalized Green's function to the full, time-dependent potential-flow equation to obtain an integral equation for the velocity potential at any point in a flow, even points on a body or whole bodies in a flow. Aerodynamic calculations are provided for two rectangular wings, a clipped-tip delta wing, and two swept wings with and without a fuselage. The number and distribution of the finite element panels are varied in order to demonstrate the convergence of the results. The results are shown to be close to those of lifting-surface theory, and further applications with bodies having deformities, arbitrary shapes, motions, and deformations are indicated.

Yates, E. C., Jr.↗