SEARCH · Engineering Papers

Results for “charging frequency”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17

All sources NASA NTRS DOE OSTI

DOE OSTI2019

Beam Tests of the PIP-II Injector Test Radio Frequency Quadrupole

In modern high intensity ion-particle accelerators, a Radio Frequency Quadrupole (RFQ) is utilized to prepare a high-quality beam for injection to the main accelerating section. Since an RFQ governs the initial beam parameters, characterization of the beam coming out from the RFQ is foremost step toward commissioning of an accelerator facili-ty. It allows validating the RFQ design as well as attaining a better understanding of charged-particle beams. This pa-per describes the beam-performance of the Proton Improvement Plan-II Injector Test (PIP2IT) Continuous Wave (CW) four vane-type RFQ. It is designed to operate at a frequency of 162.5 MHz and accelerate a nominal H- beam of 5 mA from 30 keV to 2.1 MeV. The paper details beam tests performed to validate the RFQ design specifications for trans-mission, beam kinetic energy and, RMS emittances. The paper also presents beam profile measurements and implica-tion of the beam-jitters on the effective beam emittance at the RFQ exit.

43 PARTICLE ACCELERATORS↗

DOE OSTI2024

Correlation Between Microscopic Current Fluctuations Observed at Ultra-Microelectrodes and Macroscopic Bulk Electrolysis Performance in Redox-Active Microemulsions

Microemulsions (μEs) have been proposed as redox flow battery (RFB) electrolytes that maximize ionic conductivity and charge capacity by synergizing two immiscible phases. However, charge transfer during electrolysis in μEs is poorly understood. Here, we show that ultramicroelectrode electrolysis of ferrocene-loaded μEs –20%, 60%, and 90% water - reveals stochastic current fluctuations. These are differentiated in the scanning electrochemical microscopy (SECM) geometry, where power spectral density analysis showed distinct changes in the frequency contributions. SECM in the substrate generation-tip collection mode showed that fluctuations arise under mass-transfer control. Significant differences in the diffusion coefficient of ferrocene species were deducted from SECM approach curves, suggesting phase transfer behavior. Using bulk electrolysis, we calculated the charge accessibility and cycling behavior in the μEs. A decrease in the stochastic behavior of the μEs seems to correlate to a higher accessibility and cycling performance, with the 90% water μE displaying the best reversibility and the 60% the lowest. Altogether, these results suggest that Marangoni-type convection driven by concentration gradients and/or μE restructuring during charge transfer play a role in the electrochemical performance of μEs. This presents opportunities for screening and diagnosing the performance of these emerging RFB electrolytes.

25 ENERGY STORAGE↗

DOE OSTI2025

Design, Control, and Protection of a 13.2 kV, 1 MVA Solid State Transformer for Electric Vehicle Extreme Fast Charging Station

In this article, a medium-voltage (MV) ac-dc solid state transformer (SST) for electric vehicle (EV) extreme fast charging (XFC) station is proposed. The SST adopts a cascaded H-bridge (CHB)-based structure where the active front end (AFE) power stages are connected in input-series followed by dual active bridge (DAB) converters connected in an output-parallel configuration providing galvanic isolation through a high-frequency transformer (HFT). The SST is rated for 1 MVA and connects directly to a three-phase 13.2 kV MV ac grid through ac switchgear and outputs 750-V dc. At the dc bus, several dc/dc converters are connected, each of which can charge an EV based on its battery capacity. A novel decentralized control architecture of the SST is adopted in this work which simplifies the MV dc link voltage and module-level power balancing. In addition, the local and central protection designs of the SST are presented which identify and respond to the internal fault of the system. Finally, the experimental validations of the SST hardware prototype are presented up to the rated voltage. Furthermore, this article details the design and implementation of the MV SST addressing the challenges of an isolated MV class power converter for connecting directly to the MV ac grid with unique controller architecture, distributed protection framework, and SST constructional features.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

DOE OSTI2022

Interferometric bunch length measurements of 3 MeV picocoulomb electron beams

We report picosecond bunch length measurements using an interferometric method for a 3 MeV electron beam having bunch charge ranging from 1 to 14 pC. The method senses the single-cycle sub-terahertz (THz) pulse emitted by each electron bunch as coherent transition radiation which, in turn, is analyzed using a Michelson-type interferometer, forming an interferogram that is then processed to yield the nominal electron bunch length. This sub-THz coherent radiation intensity was measured using a quasi-optical detector (QOD) operated at room temperature. This experiment was quite challenging since the divergence angle of the sub-THz pulse emitted by the low-energy electron bunch exceeds ±10°, and its pulse energy at the entrance to the detector was as low as 100 pJ. When compared to a conventional helium-cooled silicon composite bolometer designed for frequencies above 0.5 THz, the QOD provided much better signal-to-noise ratio in the ~80 GHz frequency range, which was critical for the successful measurement of the bunch length.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Proposal for a proton-bunch compression experiment at IOTA in the strong space-charge regime

The longitudinal compression of intense proton bunches with strong space-charge force is an essential component of a proton-based muon source for a muon collider. This paper discusses a proton-bunch compression experiment at the Integrable Optics Test Accelerator (IOTA) storage ring at Fermilab to explore optimal radio frequency (RF) cavity and lattice configurations. IOTA is a compact fixed-energy storage ring that can circulate a 2.5-MeV proton beam with varying beam parameters and lattice configurations. The study will aim to demonstrate a bunch-compression factor of at least 2 in the IOTA ring while examining the impact of intense space-charge effects on the compression process.

43 PARTICLE ACCELERATORS↗

DOE OSTI2024

Proposal for a Proton-Bunch Compression Experiment at IOTA in the Strong Space-Charge Regime

43 PARTICLE ACCELERATORS↗

DOE OSTI2024

Structural Trends and Vibrational Analysis of N,N,N′,N′−Tetramethylmalonamide Complexes Across the Lanthanide Series

Fundamental understanding of coordination chemistry across the lanthanide series is essential for explaining chemical behavior of rare-earth metals in complex liquid-liquid extraction processes, which in turn affects the distribution ratios and efficacy of separations as a whole. In this work, we explore the structural trends between the lanthanides and a neutral N,N,N',N'-tetramethylmalonamide (TMMA) ligand within four isolated families of solid-state compounds: Ln(trans-TMMA) 2 (NO 3 ) 3 Ln=La-Nd, Sm; Ln(cis-TMMA) 2 (NO 3 ) 3 Ln=Eu-Tb, Er; [Ln(TMMA) 3 (NO 3 ) 2 ][Ln(TMMA)(NO 3 ) 4 ] Ln=Dy-Tm; Ln(Κ 2 -TMMA)(iPrOH)(NO 3 ) 3 and Ln(Κ 1 -TMMA)(Κ 2 -TMMA)(NO 3 ) 3 Ln=Yb, Lu. Moving across the lanthanide series, we note the formation of both discrete charge-neutral complexes, as well as charged molecular anion-cation pairs, with variations in spatial ligand arrangement, coordination numbers, and ligand denticities. IR and Raman spectroscopy paired with DFT frequency calculations were used for an in-depth investigation of vibrational modes unique to each structural family. The collection of isolated model compounds was also discussed in the context of liquid-liquid separations based on reported distribution ratios from malonamide extraction.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2019

Bonding Interactions in Uranyl α-Diimine Complexes: A Spectroscopic and Electrochemical Study of the Impacts of Ligand Electronics and Extended Conjugation

Uranyl complexes of aryl-substituted α-diimine ligands gbha (UO 2 -1a-f and phen-BIAN (UO 2 -2a-f) (gbha (1) = glyoxal bis(2-hydroxyanil); phen-BIAN (2) = N,N' -bis-(iminophenol)acenaphthene; R = OMe (a), t-bu (b), H (c), Me (d), F (e), and naphthyl (f)) were designed, prepared, and characterized by X-ray diffraction, FT-IR, NMR, UV-Vis, and electrochemical methods. Furthermore these ligand frameworks contain a salen-type O-N-N-O binding pocket, but are redox-non-innocent, leading to unusual metal complex behaviors. Here, we describe three solid-state structures of uranyl complexes UO 2 -1b, UO 2 -1c, and UO 2 -1f, and observe manifestations of ligand non-innocence for the U(VI) complexes UO 2 -1b and UO 2 -1c. The impacts of accessible π-systems and ligand substitution on the axial uranium-oxo interactions can be evaluated spectroscopically via the intraligand charge-transfer (ILCT) processes that dominate the absorption spectra of these complexes and through changes to the asymmetric (ν 3 ) O=U=O stretching frequency. This, in combination with electrochemical data, reveals the effects of the inclusion of the conjugated acenaphthene backbone and the importance of ligand electronic structure on uranyl’s bonding interactions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2026

Nanosecond Structure of Radical Pair Intermediates from High-Frequency Quantum Oscillations: Insight into the Q A •– to Q B Electron Transfer Step in Purple Bacterial Photosynthesis

We demonstrate the validity of our approach to deduce, from the anisotropy of quantum oscillations, the geometry of short-lived radical pair intermediates in photosynthesis. A global fit of a two-dimensional W-band (94 GHz) electron paramagnetic resonance (EPR) experiment provides the same global minimum values for the geometry of the A-side radical pair P 700 •+ A 1A •− in photosystem I (PSI) as observed in a previous Q-band (34 GHz) EPR study, yet with a significantly increased convergence rate of 62%. This demonstrates that the global fit yields the correct radical pair geometry even at Q-band frequencies. With this information, we revisit our previous Q-band study of the cofactor arrangement of P 865 •+ Q A •− , the stabilized charge-separated state in purple bacterial reaction centers (RCs). Analysis of calculated two-dimensional data sets of P 865 •+ Q A •− reveals that the quantum oscillation technique is unaffected by a mirror ambiguity in disordered solids and thus can provide unambiguous solutions for all five Euler angles of the radical pair geometry. This enables us to elucidate the Q A •− to Q B electron transfer step in purple bacterial photosynthesis, the subject of controversial discussions for more than 25 years. Our results show that this electron transfer step involves a gating mechanism requiring a 60° rotation of the headgroup of Q A •− in its binding pocket.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2022

Squeezing Out Interfacial Solvation: The Role of Hydrogen-Bonding in the Structural and Orientational Freedom of Molecular Self-Assembly

We report bioinspired membrane molecules with improved physical properties and enhanced stability can serve as functional models for conventional lipid or amphiphilic species. Importantly, these molecules can also provide new insights into emergent phenomena that manifest during self-assembly at interfaces. Here, we elucidate the structural response and mechanistic steps underlying the self-assembly of the amphiphilic, charged oligodimethylsiloxane imidazolium cation (ODMS-MIM+) at the air–aqueous interface using Langmuir trough methods with coincident surface-specific vibrational sum-frequency generation (SFG) spectroscopy. We find evidence for a new compression-induced desolvation step that precedes commonly known disordered-to-ordered phase transitions to form nanoscopic assemblies. The experimental data was supported by atomistic molecular dynamics (MD) simulations to provide a detailed mechanistic picture underlying the assembly and the role of water in these phase transitions. The sensitivity of the hydrophobic ODMS tail conformations to compression-owing to distinct water–ODMS interactions and tail–tail solvation properties-offers new strategies for the design of interfaces that can be further used to develop soft-matter electronics and low-dimensional materials using physical and chemical controls.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2026

Magnetic brightening and nanoscale imaging of spin-polarized helical edge modes in ZrTe 5

Efficient charge transport remains a fundamental challenge for nanoelectronic devices, as their performance is constrained by high dissipation and the impedance mismatch between high-frequency signal sources and nanoscale circuit interfaces. Although topologically protected helical edge modes offer a dissipationless and backscattering-resilient alternative, achieving nanoscale control over these modes requires direct visualization of their spatial electrodynamics, especially under high-frequency operation. Here, by utilizing cryogenic magneto-infrared scattering-type scanning near-field optical microscopy (cm-IR-sSNOM), we image spin-polarized helical edge channels in ZrTe 5 at the nanoscale, revealing magnetic-field-induced brightening as a high-frequency electrodynamic signature of robust topological edge modes. Operating at 1.8 K and under a magnetic field of up to 5 T, we observe the emergence of edge-state polarizability at infrared frequencies that is notably resilient to the magnetic gaps that typically quench d.c. and microwave edge transport. Our results reveal a topological ‘two-lane’ spatial reorganization in which an external magnetic field induces a spin-population imbalance between counterpropagating edge modes. Favoured helical branches are confined against physical boundaries to activate a net infrared near-field contrast. This electrodynamic response scales linearly with the number of atomic layers, which confirms that individual layers in ZrTe 5 preserve their discrete quantum spin Hall identities. These findings may be useful for developing topological spintronic devices, as the magnetic infrared tunability of helical edge channels provides a pathway for low-loss nanoscale interconnects and high-speed information processing.

36 MATERIALS SCIENCE↗

DOE OSTI2021

A kinetic model of friction in strongly coupled strongly magnetized plasmas

Plasmas that are strongly magnetized in the sense that the gyrofrequency exceeds the plasma frequency exhibit novel transport properties that are not well understood. As a representative example, we compute the friction force acting on a massive test charge moving through a strongly coupled and strongly magnetized one-component plasma using a generalized Boltzmann kinetic theory. Recent works studying the weakly coupled regime have shown that strong magnetization leads to a transverse component of the friction force that is perpendicular to both the Lorentz force and velocity of the test charge, in addition to the stopping power component aligned antiparallel to the velocity. Recent molecular dynamics simulations have also shown that strong Coulomb coupling in addition to strong magnetization gives rise to a third component of the friction force in the direction of the Lorentz force. Here, we show that the generalized Boltzmann kinetic theory captures these effects and generally agrees well with the molecular dynamics simulations over a broad range of Coulomb coupling and magnetization strength regimes. The theory is also used to show that the “gyro” component of the friction in the direction of the Lorentz force arises due to asymmetries associated with gyromotion during short-range collisions. Computing the average motion of the test charge through the background plasma, the transverse force is found to strongly influence the trajectory by changing the gyroradius and the gyrofriction force is found to slightly change the gyrofrequency of the test charge resulting in a phase shift.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2026

Performance Characterization of InCharge™ ICE-66 V2X Bidirectional DC Fast Charger

Vehicle-to-grid (V2G) technology extends the role of Plug-in Hybrid Vehicle’s (PHEV) and Battery Electric Vehicle’s (BEV) batteries beyond transportation by enabling bidirectional power transfer between the vehicle's onboard energy storage and the utility grid. Modern battery-powered vehicles are equipped with high-capacity battery packs that remain stationary and underutilized for the majority of their operational life. A vehicle used for daily commuting may be parked and connected to charging infrastructure for 18–20 hours per day, representing a significant untapped energy resource. When considered at scale, the aggregated storage capacity of a modest fleet of 10–15 vehicles within a single parking facility can reach the MWh range, sufficient to partially offset peak demand for a mid-size commercial building or contribute meaningful ancillary services to the local grid. The ability to charge during off-peak periods when electricity prices are low and discharge during peak demand when prices are high positions EV batteries as distributed energy arbitrage assets, with the potential to offset vehicle ownership and charging costs. Beyond energy arbitrage, V2G-capable assets can provide ancillary grid services through active and reactive power injections. Active power supports grid frequency regulation, while reactive power supports local voltage regulation. Together, these capabilities establish V2G as a technically promising and economically relevant pathway toward greater integration of battery-powered vehicles into the broader energy system.

33 ADVANCED PROPULSION SYSTEMS↗

DOE OSTI2020

Bifunctional Heterometallic Metal-Organic Frameworks for Solvent-Free Heterogeneous Cascade Catalysis

A family of heterometallic metal-organic frameworks (MOFs) (CPM200s) harmoniously coexisting as Lewis acids and base (azo) sites were prepared. Seven CPM200s were employed as multifunctional heterogeneous cascade catalysts for the one-pot deacetalization-Knoevenagel reaction in a solvent-free system. Benefiting from the cooperation between Lewis acids from the open metal sites and base sites from the ligands, the CPM200s showed high activity and selectivity for the tandem reaction. The heterometallic 3D porous framework reported here not only offers a combination of two opposite active sites in the same framework of materials but also increases mass transfer of the substrate, thus maximizing the efficiency and substrate selectivity of the bifunctional catalysts. The CPM200s showed the highest turnover frequency (TOF), outperforming that of the reported MOFs in tandem with the deacetalization-Knoevenagel reaction. A strong correlation between the TOF and charge-to-radius ratio (z/r) of metal ions in the CPM200s was observed for the first time. The bifunctional CPM200s catalysts can be reused five times without significant loss of activity.

36 MATERIALS SCIENCE↗

DOE OSTI2026

Machine Learning Enabled Position Detection for 6.78 MHz UAV Wireless Power Transfer System

This paper presents a novel supervised machine learning (SML) approach for accurate position detection of the receiver coil in wireless power transfer (WPT) systems using only secondary-side electrical measurements, with applications in autonomous unmanned aerial vehicle (UAV) charging. The proposed method trains a supervised learning model to map measured secondary-side voltage and current features to the receiver’s spatial position with high precision. This enables an autonomous UAV to determine its location relative to the primary coil center, the optimal position for maximizing wireless charging efficiency. The sensing method is fully integrated into a standard WPT system, utilizing the same primary and secondary coils for both power transfer and position detection, thereby eliminating additional sensing hardware. The use of a 6.78 MHz operating frequency enhances positional sensitivity, as high-frequency near-field electromagnetic fields respond strongly to small spatial variations. Experimental validation is performed on a 30 W scaled prototype featuring a 210 mm × 140 mm primary coil, a 50 mm × 80 mm receiver coil, and a 15 mm air gap. Results demonstrate reliable position estimation and a strong correlation between predicted position and optimal coil alignment. This integrated framework unifying position detection and wireless charging offers a promising foundation for future autonomous electric vertical takeoff and landing (eVTOL) systems, enabling compact, hardware-efficient, and high-accuracy charging solutions.

Colak, Kerim [New York University]↗

DOE OSTI2020

Low-frequency lattice phonons in halide perovskites explain high defect tolerance toward electron-hole recombination

Low-cost solution-based synthesis of metal halide perovskites (MHPs) invariably introduces defects in the system, which could form Shockley-Read-Hall (SRH) electron-hole recombination centers detrimental to solar conversion efficiency. Here, we investigate the nonradiative recombination processes due to native point defects in methylammonium lead halide (MAPbI 3 ) perovskites using ab initio nonadiabatic molecular dynamics within surface-hopping framework. Regardless of whether the defects introduce a shallow or deep band state, we find that charge recombination in MAPbI 3 is not enhanced, contrary to predictions from SRH theory. We demonstrate that this strong tolerance against defects, and hence the breakdown of SRH, arises because the photogenerated carriers are only coupled with low-frequency phonons and electron and hole states overlap weakly. Both factors appreciably decrease the nonadiabatic coupling. We argue that the soft nature of the inorganic lattice with small bulk modulus is key for defect tolerance, and hence, the findings are general to other MHPs.

Science & Technology - Other Topics↗

DOE OSTI2026

Subterahertz Spin Relaxation Dynamics of Boron-Vacancy Centers in Hexagonal Boron Nitride

Quantum sensors based on spin defects have become powerful tools for detecting faint magnetic signals, yet their operation remains confined to low magnetic fields and gigahertz frequencies. Extending such sensors into high-field (>0.3 T) and subterahertz regimes would enable quantum metrology across a wide range of electromagnetic phenomena and scientific applications, but has proven challenging. Here, we demonstrate that negatively charged boron vacancies ($V^−_B$) in hexagonal boron nitride can function as relaxation-based quantum sensors operating up to 0.2 terahertz and 7 T fields. Their uniform spin-orientation and persistent spin-contrast at high fields enable measurement of intrinsic spin relaxation across unexplored field regimes. We reveal a crossover in relaxation behavior, initially decreasing at low fields before rising at higher fields, consistent with the emergence of single-phonon-induced resonant noise at subterahertz frequencies. These results establish $V^−_B$ centers as a versatile platform for quantum sensing in the subterahertz, high-field regime.

boron-vacancies↗

DOE OSTI2021

Landau Damping with Electron Lenses in Space-Charge Dominated Beams

Further progress of fundamental physics requires accelerated beams of high intensity. The intensities, however, are limited by many factors, including coherent beam instabilities. Usual methods to control the instabilities, such as octupole magnets, beam feedback dampers and employment of chromatic effects, may be ineffective or insufficient. In this study, electron lenses were proposed as a means to provide stabilizing spread in the beam betatron frequencies. It was shown that electron lenses are uniquely effective for Landau damping of transverse beam instabilities in high energy particle accelerators, and that their employment does not compromise incoherent (single particle) stability, dynamic aperture and the beam lifetime. Here we consider effectiveness of the Landau damping with electron lenses when the space charge tune shift cannot be neglected. We demonstrate that the desired stability can be assured with proper choice of the electron beam parameters and current distributions.

43 PARTICLE ACCELERATORS↗