Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “carbon defects”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Differential multi-probe thermal transport measurements of multi-walled carbon nanotubes grown by chemical vapor deposition

Carbon nanotubes (CNTs) are quasi-one dimensional nanostructures that display both high thermal conductivity for potential thermal management applications and intriguing low-dimensional phonon transport phenomena. In comparison to the advances made in the theoretical calculation of the lattice thermal conductivity of CNTs, thermal transport measurements of CNTs have been limited by either the poor temperature sensitivity of Raman thermometry technique or the presence of contact thermal resistance errors in sensitive two-probe resistance thermometry measurements. Here we report advances in a multi-probe measurement of the intrinsic thermal conductivity of individual multi-walled CNT samples that are transferred from the growth substrate onto the measurement device. The sample-thermometer thermal interface resistance is directly measured by this multi-probe method and used to model the temperature distribution along the contacted sample segment. The detailed temperature profile helps to eliminate the contact thermal resistance error in the obtained thermal conductivity of the suspended sample segment. A differential electro-thermal bridge measurement method is established to enhance the signal-to-noise ratio and reduce the measurement uncertainty by over 40%. The obtained thermal resistances of multiple suspended segments of the same MWCNT samples increase nearly linearly with increasing length, revealing diffusive phonon transport as a result of phonon-defect scattering in these MWCNT samples. The measured thermal conductivity increases with temperature and reaches up to 390 ± 20 W m –1 K –1 at room temperature for a 9-walled MWCNT. In conclusion, theoretical analysis of the measurement results suggests submicron phonon mean free paths due to extrinsic phonon scattering by extended defects such as grain boundaries. The obtained thermal conductivity is decreased by a factor of 3 upon electron beam damage and surface contamination of the CNT sample.

42 ENGINEERING↗
DOE OSTI2020

A plant genetic network for preventing dysbiosis in the phyllosphere

The aboveground parts of terrestrial plants, collectively called the phyllosphere, have a key role in the global balance of atmospheric carbon dioxide and oxygen. The phyllosphere represents one of the most abundant habitats for microbiota colonization. Whether and how plants control phyllosphere microbiota to ensure plant health is not well understood. Here we show that the Arabidopsis quadruple mutant (min7 fls2 efr cerk1; hereafter, mfec)1, simultaneously defective in pattern-triggered immunity and the MIN7 vesicle-trafficking pathway, or a constitutively activated cell death1 (cad1) mutant, carrying a S205F mutation in a membrane-attack-complex/perforin (MACPF)-domain protein, harbour altered endophytic phyllosphere microbiota and display leaf-tissue damage associated with dysbiosis. The Shannon diversity index and the relative abundance of Firmicutes were markedly reduced, whereas Proteobacteria were enriched in the mfec and cad1S205F mutants, bearing cross-kingdom resemblance to some aspects of the dysbiosis that occurs in human inflammatory bowel disease. Bacterial community transplantation experiments demonstrated a causal role of a properly assembled leaf bacterial community in phyllosphere health. Here, the pattern-triggered immune signalling, MIN7 and CAD1 are found in major land plant lineages and are probably key components of a genetic network through which terrestrial plants control the level and nurture the diversity of endophytic phyllosphere microbiota for survival and health in a microorganism-rich environment.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2023

20-kV GaN Switch Technology Demonstrated in High-Efficiency Medium-Voltage Power Module

GaN holds significant potential as a material for vertical p-n diodes, enabling the realization of devices with reverse breakdown voltages of 5 kV or higher. Carbon serves as the primary compensating dopant in the growth process, incorporated into GaN during metalorganic chemical vapor deposition (MOCVD) growth. The level of carbon incorporation depends on several factors, including growth rate, ammonia flow, temperature, pressure, and trimethylgallium (TMGa) flow. Through guided empirical modeling, the carbon incorporation in GaN growth could be predicted using a single parameter based on the ratio of ammonia flow to the growth rate. This model accurately predicts carbon concentrations ranging from 1x10 17 to 5x10 14 cm -3 while maximizing growth rates. Other extrinsic dopants have either been reduced below the threshold of consideration or modeled using similar single-parameter relationships. By identifying the dominant extrinsic dopants and accounting for them, an intrinsic defect with a concentration of 2.2x10 15 cm -3 was identified. By combining these relationships, growth conditions for n-GaN were optimized, resulting in electron concentrations as low as 1x10 15 cm -3 . Leveraging these techniques, p-n diodes were grown, achieving a reverse breakdown voltage as high as 3.1 kV.

36 MATERIALS SCIENCE↗
DOE OSTI2024

First-Principles Calculations of the Electrical Conductivity of Carbon Nanotubes Functionalized with Copper and Nitrogen: Implications for Electronics, Energy Storage, and Nanodevices

In this work, we investigate the electrical conductivity of carbon nanotubes (CNTs), with a particular focus on the effects of doping. Using first-principles-based approaches, we study the electronic structure, phonon dispersion, and electron–phonon scattering to understand the finite-temperature electrical transport properties in CNTs. Our study covers both prototypical metallic and semiconducting CNTs, with special emphasis on the influence of typical defects such as vacancies and the incorporation of copper or nitrogen, such as pyridinic N, pyrrolic N, graphitic N, and oxidized N. Our theoretical study shows significant improvements in the electrical conduction properties of copper-CNT composites, especially when semiconducting CNTs are functionalized with nitrogen. Doping is found to cause significant changes in the electronic density of states near the Fermi level, which affects the electrical conductivity. Calculations show that certain types of functional groups, such as N-pyrrolic, result in more than 30-fold increase in the conductivity of semiconducting CNTs compared to Cu-incorporated CNTs alone. For metallic CNTs, the conductivity is in agreement with existing experimental data, and our prediction of significant increases in conductivity with N-pyrrolic functional group is consistent with recent experimental results, demonstrating the effectiveness of doping in modifying conductivity. In conclusion, our study provides valuable insight into the electronic properties of doped CNTs and contributes to the development of ultrahigh conductivity CNT composites.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Microstructural evolution of a silicon carbide-carbon coated nanostructured ferritic alloy composite during in-situ Kr ion irradiation at 300°C 450°C

This work focuses on irradiation behaviors of a novel silicon carbide and carbon coated nanostructured ferritic alloy (SiC-C@NFA) composite for potential applications as a cladding and structural material for next generation nuclear reactors. The SiC-C@NFA samples were irradiated with 1 MeV Kr ions up to 10 dpa at 300 and 450 °C. Microstructures and defect evolution were studied in-situ at the IVEM-Tandem facility at Argonne National Laboratory. The effects of ion irradiation on various phases such as α-ferrite matrix, (Fe,Cr) 7 C 3 , and (Ti,W)C precipitates were evaluated. The α-ferrite matrix showed a continuous increase in dislocation density along with spatial ordering of dislocation loops (or loop strings) at >5 dpa. The size of the dislocation loops at 450 °C was larger than that at 300 °C. The nucleation and growth of new (Ti,W)C precipitates in α-ferrite grains were enhanced with the ion dose at 450 °C. This study provides new insight into the irradiation resistance of the SiC-C@NFA system.

(FeCr)(7)C-3↗
DOE OSTI2025

Synthesizing intermetallic thermoelectric materials using metal flux growth method

With zero energy poverty by 2050 goals, exploring innovative energy technologies is essential. Thermoelectric materials (TEMs) have the potential to harness waste heat and convert it to electricity (e.g., for spacecraft power, sensors, and cryogenic cooling). Two limitations of thermoelectric compounds are their low efficiency and limited pool of materials. Optimizing the efficiency of TEMs is challenging due to the interdependent relationship between electrical and thermal conductivity. A deeper understanding of electronic properties and lattice thermal conductivity is necessary to “understand, predict and ultimately control” the thermoelectric properties of TEMs. Understanding the influence of light-atom-doping and intrinsic defects on the electronic properties of the f-element containing TEMs are important questions that need to be answered to design and synthesize TEMs with optimal parameters. The purpose of this work is to understand how doping f-element based TEMs with light elements, such as carbon and boron, would impact the crystal structure, bond lengths, band gaps, and thermoelectric characteristics. High-quality f¬-element containing intermetallic single crystals are grown in metal flux media. In molten metal flux growth method, one or more low-melting metals such as aluminum, gallium, tin, and bismuth are used in excess as the reaction medium. As these are solution-state reactions, we can use lower temperatures than solid-state reactions and isolate the kinetic products instead of the thermodynamically stable compound. Then these are characterized using X-ray diffraction, scanning electron microscopy, energy dispersive spectroscopy, magnetization, electrical and thermal conductivities, and thermoelectric power.

37 - INORGANIC, ORGANIC, PHYSICAL AND ANALYTICAL C↗
DOE OSTI2025

Bio‐Inspired Cascade Photocatalysis on Fe Single‐Atom Carbon Nitride Upcycles Plastic Wastes for Effective Acetic Acid Production

Plastic imposes a critical threat to the environment, ecosystems, and human health because of the low utilization efficiency of plastics. Here, we demonstrate a sustainable, highly efficient cascade photocatalysis for upcycle plastics to value-added acetic acid using Fe single-atom catalysts (Fe@C 3 N 4 SAC) at ambient conditions. Inspired by Phanerochaete chrysosporium microbial, the defective Fe@C 3 N 4 SAC acts as a bifunctional cascade photocatalyst for both Fenton-like and CO 2 reduction reactions. During the reaction, hydroxyl radicals (*OH) form and subsequently oxidize plastics into CO 2 intermediates. These CO 2 intermediates are then photo-reduced to CH 3 COOH on the same catalyst via cascade photocatalysis. The mechanism is confirmed by in situ multimodal microscopy and spectroscopies, with density functional theory calculations. A state-of-art CH 3 COOH yield of 63.8 mg h −1 gcat −1 from PVC, 12.7 mg h −1 gcat −1 from PE, 5.4 mg h −1 gcat −1 from PET, and 5.3 mg h −1 gcat −1 from PP are directly obtained under AM1.5G solar irradiation and further validated under real sunlight (≈0.6 sun), achieving 5.6 mg h −1 gcat −1 from PET, using low-cost Fe@C 3 N 4 SAC in a sealed reactor by enhancing the photon transport and utilization efficiency. The techno-economic analysis shows it is promising to practically mitigate plastic based on broader social welfare assessments.

cascade photocatalysis↗
DOE OSTI2021

Photocurrent in carbon nanotube bundle: Graded Seebeck coefficient phenomenon

Here, polarized photovoltage of a suspended aligned carbon nanotube (CNT) bundle under uniform optical irradiation is discovered without additional structural modification or bias voltage. Such a phenomenon is very surprising considering the metallic behavior of the overall bundle and zero temperature difference between ends. The photovoltage characteristic time is found similar to the thermal response time under step Joule heating and implies a relation to the thermal behavior of the CNT bundle. A similar thermoelectric voltage is also observed during step Joule heating. Localized laser heating and scanning along the axial direction of the bundle uncovers a linear spatial variation of the local Seebeck coefficient. The Seebeck coefficient linearly decreases from root to tip of the CNT bundle with a rate of a few - µV∙K –1 ·mm –1 . Deep investigation in both the microscopic and macroscopic structures of the CNT bundle reveals that the local alignment of CNT assemblies rather than the minor defects in individual CNTs brings about this linear distribution of Seebeck coefficient in space. The finding presents a new way for direct photon-to-electric energy conversion via Seebeck coefficient grading in CNT structures.

42 ENGINEERING↗
DOE OSTI2023

Lignin-based carbon quantum dots with high fluorescence performance prepared by supercritical catalysis and solvothermal treatment for tumor-targeted labeling

The poor fluorescence performance of lignin-based carbon quantum dots (L-CQDs) prepared using the bottom-up method has hindered their development. Here, in this study, a two-step strategy was proposed to efficiently enhance the fluorescence properties of L-CQDs. Lignin was first cracked using an ethanol supercritical/noble metal catalyst; then, the L-CQDs were prepared with the cracked lignin fragments as carbon precursors without adding any modified reagents. Compared with the OL-CQDs prepared by the traditional one-pot hydrothermal method, the L-CQDs-1 prepared from CL-1 containing much low molecular weight compounds, and have photoluminescence (increased from 63 to 975) and excellent up-conversion photoluminescence (enhanced by 16.3 to 963), which significantly enhanced by about 15 times and 60 times, respectively. They can emit bright blue fluorescence under both ultraviolet and near-infrared light irradiation owing to a large amount of surface defects caused by the rich compound composition. When L-CQDs-1 were combined with, and quenched by folic acid (FA), the prepared FA@L-CQDs-1 show the ability to target and label tumor cells. This study opens new avenues for the preparation of L-CQDs with high fluorescence performance using lignocellulosic material without heteroatom additives.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2024

Characteristics of graphene oxide-like materials prepared from different deashed-devolatilized coal chars and comparison with graphite-based graphene oxide, with or without the ultrasonication treatment

Deashed-devolatilized coal chars were prepared from anthracite, bituminous, subbituminous, and lignite coals, then oxidized to prepare graphene oxide (GO)-like materials that were extensively characterized and compared with a pristine graphite-based GO sample (CGO). Coal-based GO-like materials and CGO were then subjected to ultrasonication treatment for delamination, which also impacted their physicochemical properties. The surface oxygen contents of CGO and coal-based samples were ~32 % and ~26–35 %, respectively, that were reduced to ~27 % and ~21–24 %, respectively, after ultrasonication. The Fourier transform infrared and X-ray photoelectron spectroscopy spectra of all samples showed different profiles before and after the ultrasonication, suggesting a change in chemical functionalities. The Raman spectra of CGO and coal-based samples exhibited similar D and G bands with D/G intensity ratios (I D /I G ) of 0.93 and 0.88–0.92, respectively. The I D /I G ratio of CGO and most of the coal-based samples increased after the ultrasonication due to creation of more defects. The main X-ray diffraction (XRD) peak for CGO and coal-based samples were observed at ~11° and ~22–24°, respectively. Ultrasonication of the samples resulted in a reduction of crystallite size and number of layers for all CGO and coal-based samples, confirming both splitting and delamination of carbon layers. Additionally, different coal-based samples exhibited almost overlapping XRD profiles after the ultrasonication.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Plasma-assisted atomic layer etching of single-crystal diamond

Applications of near-surface nitrogen-vacancy (NV) centers in diamond are often limited by surface defects created during processing. Understanding and controlling plasma-induced surface damage is important for preserving the optical and spin properties of diamond NV centers. We report molecular dynamics simulations of a novel form of plasma-aided atomic layer etching of diamond. In this proposed scheme, the initial surface modification step consists of Ar + ion bombardment. This creates an amorphous layer at the surface, the thickness of which is controlled by the ion energy. Amorphization is known to help smooth the surface, at least locally, and would also serve to sputter clean an initially contaminated surface. A second step impacts the amorphous carbon layer with O + between about 1 and 5 eV. Simulations show that this energy range will remove the amorphous carbon but will not etch the underlying diamond. Though this energy range is not trivial to achieve in a conventional low-temperature plasma, potential methods for creating these low-energy O + ions are discussed. In addition to a-C etching, the O + impacts are predicted to remove any isolated (100) diamond terraces by selectively attacking the edges of the terraces. The proposed atomic layer etching (ALE) approach reverses the conventional ALE sequence in which the surface modification step is usually chemical modification (oxidation in this case), followed by a removal step using Ar + impacts. This plasma ALE procedure is predicted to create a diamond surface that is atomically flat and defect free.

Draney, J. S. [Princeton University, NJ (United St↗
DOE OSTI2021

Thin-film composite membranes based on hyperbranched poly(ethylene oxide) for CO 2 /N 2 separation

Cross-linked amorphous poly(ethylene oxide) (XLPEO) is one of the leading membrane materials for post-combustion CO 2 capture. For example, XLPEO prepared from poly(ethylene glycol) methyl ether acrylate (PEGMEA) exhibited CO 2 permeability of 570 Barrer and CO 2 /N 2 selectivity of 41 at 35 °C. However, these XLPEOs cannot be dissolved in coating solutions, making it impossible to be fabricated into thin-film composite (TFC) membranes using state-of-the-art manufacturing processes. In this study, we synthesized high molecular weight yet soluble HPEO via atom transfer radical polymerization (ATRP). These polymers were thoroughly characterized and compared with XLPEO, including thermal transitions, free volumes, and pure-gas sorption and permeation properties. A polymer with the best combination of CO 2 permeability (540 Barrer) and CO 2 /N 2 selectivity (43) was fabricated into defect-free TFC membranes with a thickness as thin as 506 ± 44 nm. When challenged with simulated flue gas containing water vapor at 35 °C for over 100 h, the membrane shows stable CO 2 permeance of 850 GPU and CO 2 /N 2 selectivity of 37, comparable to the leading commercial membranes for carbon capture.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

A comparison of carbon impurities in pre- and post-melt uranium Part 2: Scanning/Transmission electron microscopy analysis

We report the speciation and morphology of U carbide inclusions in pre- and post-melt U metal have been explored using high-resolution analytical electron microscopy (AEM). This report presents Part 2 of our study, in which aberration (C s ) corrected transmission and scanning transmission electron microscopy (S)TEM was used to elementally and crystallographically characterize C-containing impurities and defect features in U samples for comparison with results obtained by scanning electron microscopy (SEM) in Part 1, previously published by this journal. Elemental mapping and unit cell matching of inclusions by (S)TEM are consistent with phases observed by SEM, and new dislocations can be observed associating with some inclusion morphologies and not others.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Formation of Amorphous Carbon Multi‐Walled Nanotubes from Random Initial Configurations

Amorphous carbon nanotubes (a‐CNT) with up to four walls and sizes ranging from 200 to 3200 atoms have been simulated, starting from initial random configurations and using the Gaussian Approximation Potential. The important variables (like density, height, and diameter) required to successfully simulate a‐CNTs were predicted with the machine learning random forest technique. The width of the a‐CNT models ranged between 0.55–2 nm with an average inter‐wall spacing of 0.31 nm. The topological defects in a‐CNTs were analyzed and new defect configurations were observed. The electronic density of states and localization in these phases were discussed and delocalized electrons in the π subspace were identified as an important factor for inter‐layer cohesion. Spatial projection of the electronic conductivity favors axial transport along connecting hexagons, while non‐hexagonal parts of the network either hinder or bifurcate the electronic transport. A vibrational density of states was calculated and is potentially an experimentally comparable fingerprint of the material. The appearance of a low‐frequency radial breathing mode was discussed and the thermal conductivity at 300 K was estimated using the Green‐Kubo formula.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2021

Constructing high-performance radiation-resistant ternary YSZ-MgO-CNT nanocomposites via tailored nanostructures

Developing long-lifetime bulk-form ceramic-based materials with high irradiation resistance is crucial for advanced nuclear systems. Here, we incorporated carbon nanotubes (CNTs) into yttria-stabilized zirconia (YSZ) and magnesia (MgO) nanocrystals to fabricate bulk YSZ-MgO-CNT nanocomposites with abundant ternary nanostructures by spark plasma sintering. To understand the role of tailored ternary nanostructure on irradiation, we investigated the microstructure and mechanical properties evolutions of the YSZ-MgO-CNT nanocomposites irradiated by multi-energy He + ions at high temperature to different fluences. Compared with the single-phase YSZ and ultrafine-grained YSZ-MgO composites, the YSZ-MgO-CNT nanocomposites possessed higher ability to manage irradiation-induced He bubbles/defects via the defect-interface interactions of proposed “loading-unloading” and “loading-transporting-unloading” mechanisms for controlling the dynamical behaviors of He atoms/defects in the CNT-doped ternary nanostructures, thereby presenting more stable microstructure and better performance in resisting irradiation hardening. In conclusion, this work provides insight into the design of advanced inert matrix nuclear fuel and new nuclear waste management materials.

36 MATERIALS SCIENCE↗
DOE OSTI2020

High-Resolution Three-Dimensional Sculpting of Two-Dimensional Graphene Oxide by E-Beam Direct Write

On demand switchable additive/subtractive patterning of 2D nanomaterials is an essential capability for developing new concepts of functional nanomaterials and their device realizations. Traditionally, this is performed via a multi-step process using photoresist coating and patterning by conventional photo or electron beam lithography, which is followed by bulk dry/wet etch or deposition. This limits the range of functionalities and structural topologies that can be achieved, as well as increases the complexity, cost, and possibility of contamination which are significant barriers to device fabrication from highly sensitive 2D materials. Focused electron beam induced processing (FEBIP) enables a material chemistry/site-specific, high-resolution multi-mode atomic scale processing and provides unprecedented opportunities for direct-write, single-step surface patterning of 2D nanomaterials with an in-situ imaging capability. It allows for realizing a rapid multi-scale/multi-mode approach, ranging from an atomic scale manipulation (e.g., via targeted defect introduction as an active site) to a large-area surface modification on nano and micro scales, including patterned doping and material removal/deposition with 2D (in-plane)/3D (out-of-plane) control. In this work, we report on a new capability of FEBIP for nanoscale patterning of graphene oxide via removal of oxygenated carbon moieties with no use of reactive gas required for etching complemented by carbon atom deposition using focused electron beam. The mechanism of experimentally observed phenomena is explored using the density functional theory (DFT) calculations, revealing that interactions of e-beam liberated reactive oxygen radicals with carbon atoms on graphene basal plane lead to creation of atomic vacancies in the material. The reaction by-products are volatile carbon di-oxides, which are dissociated and volatilized from the graphene oxide surface functional groups by interactions with an energetic focused electron beam. Along with selective “subtractive” patterning of graphene oxide, the same electron beam with increased irradiation doses can deposit out-of-plane 3D carbon nanostructures on top of or around the 2D etched pattern, thus forming a hybrid 2D/3D nanocomposite with feature control down to a few nanometers. Furthermore, this in-operando dual nanofabrication capability of FEBIP is unmatched by any other nanopatterning techniques and opens a new design window for forming 2D/3D complex nanostructures and functional nanodevices.

36 MATERIALS SCIENCE↗
DOE OSTI2022

The role of H–H interactions and impurities on the structure and energetics of H/Pd(111)

Understanding hydrogen incorporation into palladium requires detailed knowledge of surface and subsurface structure and atomic interactions as surface hydrogen is being embedded. Using density functional theory (DFT), we examine the energies of hydrogen layers of varying coverage adsorbed on Pd(111). Here we find that H–H and H–Pd interactions promote the formation of the well-known ($\sqrt{3}$ x $\sqrt{3}$) phases but also favor an unreported (3 × 3) phase at high H coverages for which we present experimental evidence. We relate the stability of isolated H vacancies of the (3 × 3) phase to the need of H 2 molecules to access bare Pd before they can dissociate. Following higher hydrogen dosage, we observe initial steps of hydride formation, starting with small clusters of subsurface hydrogen. The interaction between H and Pd is complicated by the persistent presence of carbon at the surface. X-ray photoelectron spectroscopy experiments show that trace amounts of carbon, emerging from the Pd bulk despite many surface cleaning cycles, become mobile enough to repopulate the C-depleted surface at temperatures above 200 K. When exposed to hydrogen, these surface carbon atoms react to form benzene, as evidenced by scanning tunneling microscopy observations interpreted with DFT.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Multiscale characterization and representation of variability in ceramic matrix composites

Low density, high strength, and high creep and oxidation resistance properties of ceramic matrix composites (CMCs) make them an ideal choice for use in extreme environments in space and military applications. This paper presents a detailed characterization study of structural and manufacturing flaws in Carbon fiber Silicon-Carbide-Nitride matrix (C/SiNC) CMCs at different length-scales. Energy-dispersive spectroscopy (EDS) is used for the chemical characterization of the material’s elemental constituents. High-resolution multiscale graphs obtained from scanning electron microscope (SEM) and confocal laser scanning microscope (LSM) are used to characterize the distribution and morphology of defects at different length scales. This is followed by the classification and quantification of the common manufacturing defects. An image processing algorithm based on the image segmentation process is developed to quantify the variability of various scale-dependent architectural parameters. Finally, a three-dimensional stochastic representative volume element (SRVE) generation algorithm is developed to provide precise representations of material textures at multiple length scales. The developed algorithm accurately accounts for material features and flaws based on a range of multiscale structural and defects characterization results.

36 MATERIALS SCIENCE↗