Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “atomic mobility”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Temperature-dependent cavity swelling in dual-ion irradiated Fe and Fe-Cr ferritic alloys

Fe-Cr ferritic-martensitic (FM) steels are promising structural material candidates for fusion and advanced fission reactors due to their attractive mechanical properties and volumetric swelling resistance. However, significant discrepancies exist regarding the effect of solutes and irradiation temperature on cavity swelling under ion versus neutron irradiation conditions. In this study, simultaneous dual ion irradiations (8 MeV Ni 3+ ions and energy-degraded 3.5 MeV He 2+ ions) were used to quantify the cavity swelling behavior in ultra-high purity Fe and Fe-Cr alloys (3-14 wt.% Cr), Fe-10 wt.% Cr-780 wt.ppm C, and Eurofer97 FM steel. The irradiations were conducted over a wide temperature range (400-550°C) with a mid-range dose of ~30 displacements per atom (dpa) and 0.1 appm/dpa He implantation rate. Here, using state-of-the-art transmission electron microscopy (TEM), we reveal that pure Fe has a ~50°C lower peak swelling temperature difference than Fe-Cr alloys, which is attributed to higher vacancy mobility in pure Fe. Chromium solute appears to strongly suppress cavity swelling in Fe-Cr alloys for temperatures below ~470°C, but seems to have little effect or slightly enhances swelling above ~470°C. Cavities were observed in all the irradiated samples between 400-550°C. This indicates that the narrow temperature range of observable cavities reported in prior ion irradiated Fe-Cr ferritic alloy studies is likely an artifact associated with the use of low ion energies (<5 MeV), which leads to pronounced near-surface and implanted ion effects that suppress cavity swelling even at midrange depths (particularly at high temperatures).

36 MATERIALS SCIENCE↗
DOE OSTI2025

Reduced thermal resistance of Al-rich AlGaN HEMTs via top-side diamond integration

We report back-end-of-line growth of nanocrystalline diamond (NCD) on ultrawide bandgap (UWBG) high Al content aluminum gallium nitride (AlGaN) channel high electron mobility transistors for thermal management. A thin (∼15 nm) silicon nitride (SiN x ) interlayer was deposited to protect the device surface before performing a low temperature (500 °C) NCD growth process in an attempt to protect the gates on these fully fabricated devices. Notably, atomic force microscopy showed that the maximum lateral grain size exceeded 300 nm even though the film thickness was ∼250 nm. Comparing electrical (DC) performance before and after NCD growth, the gate leakage increased by ∼10 2 after NCD growth. Despite the lower NCD growth temperature, intermixing of the Ni and Au was observed in the Schottky gate metal stack; however, we believe there is another mechanism, possibly hydrogen-related, that is responsible for the measured increase in gate leakage. Regarding thermal management, the device-level thermal resistance (quantified using the average gate temperature rise measured by thermoreflectance imaging) was reduced by 29% through the incorporation of the top-side diamond film. Using time-domain thermoreflectance, the thermal conductivity of the ≈250 nm thick NCD film was measured to be 45 ± 25 W m −1 K −1 . This is expected to be at least 5× greater than the thermal conductivity of the thin disordered AlGaN alloy. There could also be a coupled electrothermal component contributing to the reduced temperature rise from electric field spreading and consequent heat spreading. This study demonstrates a promising first step toward device-level thermal management of high power UWBG Al-rich AlGaN devices.

Lundh, James Spencer [U.S. Naval Research Laborato↗
DOE OSTI2020

A Conceptual Design for a Desktop Application to Support Inventory Reconciliation Activities

This paper describes desktop software being developed at Oak Ridge National Laboratory (ORNL) to empower users to reconcile observations about items at nuclear facilities more accurately, reliably, and quickly. Inventory activities at nuclear facilities are often conducted using pen and paper, which can be time-consuming, tedious, and susceptible to reading or transcription errors. The proposed inventory assistant would be a replacement for the paper-based process that could be used by International Atomic Energy Agency (IAEA) inspectors, nuclear facility operators, or treaty verification monitors to conduct an inventory of nuclear and non-nuclear items in a more timely and accurate manner. Garner, McGirl, and Whitaker previously reported their work about a conceptual design for a mobile app to assist users in the field. In general, the inventory assistant would ingest an inventory list, distribute assigned items from the inventory list to one or more mobile devices, enable inventory teams to record their observations in the field, and then enable an inventory lead to integrate and reconcile the observations to produce a final report. The assistant consists of two software components - one for the inventory teams to record observations in the field (In-Field Observations App [IFOA]) and one for the inventory lead to (1) distribute the inventory list to each team, (2) integrate the observations from each team, and (3) reconcile the inventory list with observations (Distribution, Integration, and Reconciliation Application [DIRA]). This paper reviews the inventory assistant workflow and describes the DIRA user experience in more detail. As an example, the authors have chosen to follow the use case of IAEA inspectors conducting item counting and tag checking activities of UF 6 cylinders at a gas centrifuge enrichment plant with a large number of UF 6 cylinders (e.g., thousands). These activities can currently require 30 - 40 person-days of inspection to complete. The authors believe an inventory assistant could allow the IAEA to complete item counting and tag checking using the global identifier or the operator’s barcode in 8 - 10 person-days of inspection. We would expect other users (e.g., facility operators or treaty verification monitors) to also benefit from significant time savings.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2021

Establishing a unified framework for ion solvation and transport in liquid and solid electrolytes

Electrolytes used in rechargeable batteries must enable rapid translation of the working ion between macroscopically separated electrodes. These electrolytes are, however, usually designed and synthesized using atomic-level insights. Whether the ideal electrolyte for a particular battery is a solid or a liquid remains an important unresolved question, especially as solids with conductivities comparable with liquids are discovered. Here, to help resolve such questions, we present the first steps toward a unified framework for relating atomic and continuum scale phenomena. Solvation shells in liquids are entities that translate with the working ion for a short while before they break up due to Brownian motion. By contrast, solvation cages in classical solids and polymers cannot not translate with the working ion. Mobility of the entities that make up the cages and shells, which is quantified by an order parameter, is shown to influence translation of the working ion on continuum length scales.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Super-Resolved Single-Molecule Tracking Studies of Rhodamine B Accumulation on Fresh and Aged Polyethylene Terephthalate

It is well-known that toxic organic micropollutants (OMs) accumulate on the surfaces of microplastics. However, much remains to be learned about the exact molecular level mechanisms of OM accumulation and how these evolve as the plastics age. In this work, super-resolved single-molecule tracking (SMT) is used for the first time to investigate the accumulation of Rhodamine B (RhB) dye on fresh and artificially aged polyethylene terephthalate (PET) surfaces. PET thin films serve as models for microplastics, while RhB serves as a proxy for the OMs they accumulate. Artificial aging of the films is accomplished by exposing them in a UV-ozone chamber. Water contact angle, spectroscopic ellipsometry, and carbonyl index measurements reveal a gradual decrease in film hydrophobicity, thickness, and carbonyl content with age. Atomic force microscopy (AFM) data reveal an increase in surface roughness and confirm that the films remain largely intact and continuous across the aging times explored. In SMT experiments, wide-field fluorescence videos acquired from the water/PET interface under 7.5 pM RhB reveal both mobile and immobile dye molecules. Measurements of the frame-to-frame displacements of the dye show that diffusion occurs by a desorption-mediated mechanism and that the diffusion rate varies with PET film age. The surface density of mobile dye molecules decreases with increasing PET age, while the population of immobile molecules becomes relatively larger, suggesting an age-dependent transformation of the mechanism(s) by which the dye is accumulated. SMT data reveal that both mobile and immobile molecules repeatedly adsorb over the same surface sites, consistent with the emergence of nanoscale PET surface heterogeneity also revealed by AFM. Estimates of the adsorption coefficients are obtained using a nearest-neighbor analysis, giving values from 9.9 × 10 5 to 2.1 × 10 6 M –1 for immobile molecules and from 1.8 × 10 5 to 2.5 × 10 5 M –1 for mobile molecules on fresh and 5 min aged PET, respectively. Here, anomalous age-dependent variations in the velocity of molecular motion on the PET surface and in the population of immobile molecules are shown to correlate with changes in the strength of RhB adsorption.

Adsorption↗
DOE OSTI2020

Single‐Site, Single‐Metal‐Atom, Heterogeneous Electrocatalyst: Metal–Organic‐Framework Supported Molybdenum Sulfide for Redox Mediator‐Assisted Hydrogen Evolution Reaction

Abstract Synthesis of single‐site catalysts, whereby the local structure and surrounding chemical environments are identical, has been challenging, particularly in heterogeneous catalysis, as the support often presents spectrum of chemically distinct binding sites. Yet, the above criteria are crucial in attributing the apparent catalytic performance to the structural motif. The presented work augments on our previous work using monometallic molybdenum sulfide tethered within a zirconium‐based metal‐organic framework (MOF), NU‐1000; the monometallic nature enables all presented sites to be catalytically addressable. As the molybdenum sulfide species resided within two distinct pores (micro‐ and mesopores) of the MOF support, we have imparted uniformity in the local chemical environment by reducing the pore heterogeneity down to a single mesopore. Single‐site and single‐atom nature of the candidate catalyst was established via X‐ray diffraction measurements. Redox mediators were implemented, which, under reductive potentials, provide reduced species; they can effectively deliver the necessary reducing equivalences to the catalytic units that can otherwise not be addressed electrochemically due to the low electron mobility within the framework. Our results indicate the micropore‐allocated molybdenum sulfide is approximately four times more active as that in mesopores, whereas its catalytic mechanism is identical, underscoring the importance of controlling chemical environment beyond the active site.

Noh, Hyunho↗
DOE OSTI2025

In-Situ Atomic-Scale Revelation of Amorphous Metallic Iron Formation during Hydrogen-Driven Reduction of Iron Oxides

The transition to hydrogen as a green reductant in metal production is critical for decarbonizing the metallurgical industry, yet atomic-scale mechanisms governing reduction pathways and phase evolution remain unresolved. Using in-situ environmental transmission electron microscopy, we identify a hidden pathway that reveals dynamic formation of amorphous metallic iron (Fe) during the hydrogen-driven reduction of ferrous oxides of Fe 3 O 4 and FeO. Real-time imaging uncovers three coexisting transformation routes: (i) Fe 3 O 4 → FeO, (ii) Fe 3 O 4 → amorphous Fe, and (iii) FeO → amorphous Fe. The resulting amorphous Fe exhibits fluid-like mobility, enabling its rapid aggregation and crystallization into core-shell nanostructures, with a crystalline core enveloped by an amorphous shell. Complementary ab initio molecular dynamics simulations trace the amorphous Fe formation to interfacial strain at the metal/oxide interfaces, where large lattice mismatches destabilize the metal lattice during initial metallization. This interplay between thermodynamics and kinetics governs phase evolution: thermodynamics favors a self-limiting amorphous Fe overlayer, while rapid oxide reduction kinetics drives amorphous overgrowth. Our findings demonstrate that amorphous intermediates bypass rate-limiting crystalline steps, providing mechanistic insights to optimize H 2 -based processes for sustainable steelmaking. In conclusion, these insights bridge the gap between macroscopic process engineering and atomic-scale dynamics, with broader implications for catalysis and nanostructured material synthesis, where oxide reduction pathways critically shape functional phases and microstructures.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Strongly Anharmonic Phonons and Their Role in Superionic Diffusion and Ultralow Thermal Conductivity of Cu 7 PSe 6

We report the quest for advanced superionic materials requires understanding their complex atomic dynamics, but detailed studies of the interplay between lattice vibrations and ionic diffusion remain scarce. Here inelastic and quasielastic neutron scattering measurements in the superionic argyrodite Cu 7 PSe 6 are reported, combined with molecular dynamics (MD) based on ab initio and machine-learned potentials, providing critical insights into the atomistic mechanisms underlying fast ion conduction. The results reveal how long-range Cu diffusion is limited by intercluster hopping, controlled by selective anharmonic phonons of the crystalline framework. Further, the Green–Kubo simulations reproduce the ultralow lattice thermal conductivity and identify contributions from mobile ions, phonons, and their cross-correlations. The mode resolved analysis shows that the thermal conductivity is dominated by low-energy acoustic phonon modes of the overall crystal framework. The analysis of mode-resolved spectral functions further show that vibrational modes with significant Cu contributions are strongly damped, corresponding to the breakdown of associated phonon quasiparticles. These results highlight the importance of strongly anharmonic effects in superionic systems, in which the traditional quasiharmonic phonon picture is insufficient, and pave the way toward combining machine-learning accelerated simulations with neutron scattering experiments to rationalize the complex atomic dynamics underlying ionic and thermal transport.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Theoretical Investigation of the Hydrogenation of Cyclohexene Catalyzed by Supported Single-Atom Sites on Redox Noninnocent LiMn 2 O 4 and Li 2 Mn 2 O 4 Surfaces

Here, the tuning of catalyst activity via stereoelectronic modulation of the active-site structure remains a grand challenge in heterogeneous catalysis. In homogeneous catalysis, the redox noninnocent ligands can be introduced to organometallic fragments to donate electrons to the metal center and fine-tune the catalytic activity. Analogously, lithium-ion battery materials, such as lithium manganese oxide (LMO), lithium titanium oxides (LTO), etc., can serve as redox noninnocent catalyst support to modulate the electronic structures of the active site via lithiation, hence tuning the catalytic activity of supported active sites. Experimentally, the Ni single-atom site was supported on LiMn 2 O 4 via oxidative grafting and exhibited no catalytic activity toward the hydrogenation of cyclohexene. After introducing additional Li into the catalyst support forming Li 2 Mn 2 O 4 , the Ni single-atom site becomes active, with the catalytic rates increasing as a function of the lithiation for Li/Mn ratios >0.9. In this paper, density functional theory (DFT) calculations are performed to study the Ni site structure via X-ray absorption near edge structure (XANES) simulations and investigate the electronic properties of Ni single-atom site before and after the addition of intercalated lithium in the LMO spinel structure. Furthermore, the study of the reaction mechanism is also carried out to understand the thermodynamically and kinetically favored pathways. XANES simulation suggests that the Ni single-atom site is likely to stay in the Li channel of the spinel support structure and form an octahedral structure. After Li intercalation, the Ni site becomes less positively charged, indicating the partial reduction of the Ni site. The simulated reaction energy profile over the LiMn 2 O 4 support exhibits high-energy barriers (1.07 eV) for the hydrogenation of cyclohexene; however, the Li 2 Mn 2 O 4 support is able to better stabilize low-coordinated ion sites and improve ion mobility, leading to lower overall energy barriers (0.64 eV). The reduced and low-coordinated ion site, thus, can better stabilize the reaction intermediates and promote hydrogenation reaction. Similarly, other transition metal ions (Fe, Co, and Cu) are also considered over the LiMn 2 O 4 and Li 2 Mn 2 O 4 catalyst supports for hydrogenation reaction.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Light-activated interlayer contraction in two-dimensional perovskites for high-efficiency solar cells

Understanding and tailoring the physical behaviour of halide perovskites under practical environments is critical for designing efficient and durable optoelectronic devices. Here, we report that continuous light illumination leads to >1% contraction in the out-of-plane direction in two-dimensional hybrid perovskites, which is reversible and strongly dependent on the specific superlattice packing. X-ray photoelectron spectroscopy measurements show that constant light illumination results in the accumulation of positive charges in the terminal iodine atoms, thereby enhancing the bonding character of inter-slab I–I interactions across the organic barrier and activating out-of-plane contraction. Correlated charge transport, structural and photovoltaic measurements confirm that the onset of the light-induced contraction is synchronized to a threefold increase in carrier mobility and conductivity, which is consistent with an increase in the electronic band dispersion predicted by first-principles calculations. Flux-dependent space-charge-limited current measurement reveals that light-induced interlayer contraction activates interlayer charge transport. Lastly, the enhanced charge transport boosts the photovoltaic efficiency of two-dimensional perovskite solar cells up to 18.3% by increasing the device’s fill factor and open-circuit voltage.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Investigation of the Effect of Temperature on the Structure of SARS-CoV-2 Spike Protein by Molecular Dynamics Simulations

Statistical and epidemiological data imply temperature sensitivity of the SARS-CoV2 coronavirus. However, the molecular level understanding of the virus structure at different temperature is still not clear. Spike protein is the outermost structural protein of the SARS-CoV-2 virus which interacts with the Angiotensin Converting Enzyme 2 (ACE2), a human receptor, and enters the respiratory system. In this study, we performed an all atom molecular dynamics simulation to study the effect of temperature on the structure of the Spike protein. After 200 ns of simulation at different temperatures, we came across some interesting phenomena exhibited by the protein. We found that the solvent exposed domain of Spike protein, namely S1, is more mobile than the transmembrane domain, S2. Structural studies implied the presence of several charged residues on the surface of N-terminal Domain of S1 which are optimally oriented at 10– 30°C. Bioinformatics analyses indicated that it is capable of binding to other human receptors and should not be disregarded. Additionally, we found that receptor binding motif (RBM), present on the receptor binding domain (RBD) of S1, begins to close around temperature of 40°C and attains a completely closed conformation at 50°C. We also found that the presence of glycan moieties did not influence the observed protein dynamics. Nevertheless, the closed conformation disables its ability to bind to ACE2, due to the burying of its receptor binding residues. Our results clearly show that there are active and inactive states of the protein at different temperatures. This would not only prove beneficial for understanding the fundamental nature of the virus, but would be also useful in the development of vaccines and therapeutics.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2024

Enhanced Thermal Stability of Conductive Mercury Telluride Colloidal Quantum Dot Thin Films Using Atomic Layer Deposition

Colloidal quantum dots (CQDs) are valuable for their potential applications in optoelectronic devices. However, they are susceptible to thermal degradation during processing and while in use. Mitigating thermally induced sintering, which leads to absorption spectrum broadening and undesirable changes to thin film electrical properties, is necessary for the reliable design and manufacture of CQD-based optoelectronics. Here, low-temperature metal–oxide atomic layer deposition (ALD) was investigated as a method for mitigating sintering while preserving the optoelectronic properties of mercury telluride (HgTe) CQD films. ALD-coated films are subjected to temperatures up to 160 °C for up to 5 h and alumina (Al 2 O 3 ) is found to be most effective at preserving the optical properties, demonstrating the feasibility of metal–oxide in-filling to protect against sintering. HgTe CQD film electrical properties were investigated before and after alumina ALD in-filling, which was found to increase the p-type doping and hole mobility of the films. The magnitude of these effects depended on the conditions used to prepare the HgTe CQDs. With further investigation into the interaction effects of CQD and ALD process factors, these results may be used to guide the design of CQD–ALD materials for their practical integration into useful optoelectronic devices.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Low Ohmic contact resistance and high on/off ratio in transition metal dichalcogenides field-effect transistors via residue-free transfer

Beyond-silicon technology demands ultrahigh performance field-effect transistors. Transition metal dichalcogenides provide an ideal material platform, but the device performances such as the contact resistance, on/off ratio and mobility are often limited by the presence of interfacial residues caused by transfer procedures. Here, we show an ideal residue-free transfer approach using polypropylene carbonate with a negligible residue coverage of ~0.08% for monolayer MoS 2 at the centimetre scale. By incorporating a bismuth semimetal contact with an atomically clean monolayer MoS 2 field-effect transistor on hexagonal boron nitride substrate, we obtain an ultralow Ohmic contact resistance of ~78 Ω µm, approaching the quantum limit, and a record-high on/off ratio of ~10 11 at 15 K. Further, such an ultra-clean fabrication approach could be the ideal platform for high-performance electrical devices using large-area semiconducting transition metal dichalcogenides.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2024

Effects of Al concentration on the structure and conductivity of lithium lanthanum zirconium oxide

Cubic Li 7-3x Al x La 3 Zr 2 O 12 (LLZO) is a promising, next-generation solid electrolyte due to its stability with Li-metal and high bulk conductivity (~1 mS cm -1 ). However, the source of the high conductivity is not completely understood. In this work, we address this key knowledge gap through the integration of elemental analysis, neutron diffraction sensitive to Li and O atoms, and impedance spectroscopy to understand the structure–property correlations for LLZO. We show the metal–oxygen framework structure remains constant with variation in Al substitution, resulting in a constant activation energy of ~0.35 eV and little effect on the bulk conductivity. Instead, Li concentration, Al blocking and trapping of mobile defects, and Li–Li nearest neighbor interactions largely control the Al substituted LLZO bulk conductivity, resulting in decreases from 0.73 to 0.22 mS cm -1 as the Al concentration increases from 0.17 to 0.32 mol. These results differ from those of Ta substituted LLZO, where the framework structure and Li–Li site distances play large roles in controlling the conductivity. The increased understanding of the controlling factors of conductivity allows for greater ability to tailor the design of and substitution into the LLZO structure for improved conductivity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS2008

Effects of a Tantalum Addition on the Morphological and Compositional Evolutions of a Model Ni-AL-Cr Superalloy

The effects of a 2.0 at.% addition of Ta to a model Ni-Al-Cr superalloy aged at 1073 K are assessed using scanning electron microscopy and atom-probe tomography. The addition of Ta results in appreciable strengthening, and the morphology is found to evolve from a bimodal distribution of spheroidal precipitates, to cuboidal precipitates aligned along the elastically soft <001>-type directions. Tantalum is observed to partition preferentially to the gamma -precipitate phase and decreases the mobility of Ni in the gamma- matrix sufficiently to cause an accumulation of Ni on the gamma-matrix side of the gamma -precipitate/gamma-matrix heterophase interface.

Booth-Morrison, Christopher↗
DOE OSTI2023

Enhancing the electron mobility in Si-doped (010) β-Ga 2 O 3 films with low-temperature buffer layers

We demonstrate a new substrate cleaning and buffer growth scheme in β-Ga 2 O 3 epitaxial thin films using metal–organic vapor phase epitaxy (MOVPE). For the channel structure, a low-temperature (LT, 600 °C) un-doped Ga 2 O 3 buffer was grown, followed by a transition layer to a high-temperature (HT, 810 °C) Si-doped Ga 2 O 3 channel layers without growth interruption. The (010) Ga 2 O 3 Fe-doped substrate cleaning uses solvent cleaning, followed by additional hydrofluoric acid (49% in water) treatment for 30 min before the epilayer growth. This step is shown to compensate the parasitic Si channel at the epilayer–substrate interface that originates from the substrate polishing process or contamination from the ambient. From secondary ion mass spectroscopy (SIMS) analysis, the Si peak atomic density at the substrate interface is found to be several times lower than the Fe atomic density in the substrate—indicating full compensation. The elimination of the parasitic electron channel at the epi–substrate interface was also verified by electrical (capacitance–voltage profiling) measurements. In the LT-grown (600 °C) buffer layers, it is seen that the Fe forward decay tail from the substrate is very sharp, with a decay rate of ∼9 nm/dec. X-ray off-axis rocking curve ω-scans show very narrow full width at half maximum (FWHM) values, similar to the as-received substrates. These channels show record high electron mobility in the range of 196–85 cm 2 /V⋅s in unintentionally doped and Si-doped films in the doping range of 2 × 10 16 –1 × 10 20 cm −3 . Si delta-doped channels were also grown utilizing this substrate cleaning and the hybrid LT buffers. Record high electron Hall mobility of 110 cm 2 /V⋅s was measured for sheet charge density of 9.2 × 10 12 cm −2 . This substrate cleaning, combined with the LT buffer scheme, shows the potential of designing Si-doped β-Ga 2 O 3 channels with exceptional transport properties for high-performance Ga 2 O 3 -based electron devices.

Bhattacharyya, Arkka↗
DOE OSTI2020

Observation of [VCu1–Ini2+VCu1–] Defect Triplets in Cu-Deficient CuInS2

Copper indium disulfide (CuInS2) is a semiconductor with a direct energy band gap of 1.53 eV, an optimal value for highly efficient thin-film solar cells. But it has reached only ~ 11 % power conversion efficiency, far less than the theoretically achievable value of ~ 30 %. The cause of this low performance is not understood. A single crystal grown from 1 mol% Cu-deficient melt was studied, using atomic resolution high-angle annular dark-field (HAADF) scanning transmission electron microscopy (STEM) and electron dispersive spectroscopy (EDS). While the bulk crystal is exactly stoichiometric CuInS2, it contains nanometer-thick, structurally coherent, Cu-deficient interphases that form along rotational twin boundaries in the {112} plane. Transition zones from bulk crystal to interphase are observed, where In is seen to move from its normal site InIn in the chalcopyrite structure to a tetrahedral interstitial site Ini, while Cu remains in its normal CuCu position. Two InIn rows of the bulk crystal merge into one row of Ini, causing excess Ini in the interphase. The concentrations of CuCu and Ini reflect a ratio of Cu vacancies, VCu, to excess Ini of ~ 2. Their relative lattice positions, and the high electrical resistivity of the crystal, suggests that VCu and excess Ini ‘precipitate’ as self-compensating, electrically neutral, [VCu1- Ini2+ VCu1-] defect triplets. This is the first atomic-level observation of the ordered defect that has been invoked as the basic structural modifier in chalcopyrite compound homologs. The interphases introduce an optical gap of 1.47 eV. Electron trapping in band tail states, evident from a photoconductivity exponent of 0.54, is the likely cause of an unusually low electron mobility of 0.1 cm2V-1s-1. The overall result is that making CuInS2 slightly copper-poor inserts nanometer-thick layers of the interphase into the bulk crystal. This study shows that apparently conflicting results of the effect of Cu deficiency on CuInS2 thin-film solar cells may be resolved by analyzing structure and composition at nanometer spatial resolution.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗