SEARCH · Engineering Papers

Results for “alloy development”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17

All sources NASA NTRS DOE OSTI

DOE OSTI2025

Stimulating β -Series Precipitation in Mg–Nd Alloys Via Microalloying: A Comparison of Electron Microscopy and Small-Angle Scattering Techniques

The Mg–Nd alloy system is of particular interest in the development of high-strength, lightweight structural alloys due to the formation of strengthening metastable Mg–Nd β-series precipitates during heat treatment. The strengthening is primarily provided by a combination of the β''' and β 1 precipitation. It is therefore important to understand how the precipitation behavior can be enhanced by other common alloying elements. In this work, the effects of 0.2 wt pct Zn and Ca on β-series precipitation were studied. Small-angle/ultra-small-angle X-ray scattering (SAXS/USAXS) techniques in combination with scanning transmission electron microscopy (STEM) were used to study the evolution of precipitation microstructure. Here, it is found that the Zn additions refine the precipitates, leading to an increase in hardness with aging at 200 °C. On the other hand, the Ca additions result in an acceleration in the formation of larger β 1 precipitates and chains which provides less strengthening. The β 1 chains are surrounded by precipitate-free zones (PFZs) that further contribute to the decreases in hardness observed in the over-aged condition. This paper demonstrated that SAXS/USAXS provides a powerful tool for an in situ study of the early stages of precipitation in the Mg–Nd-based alloys.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Effect of Si impurities on microstructure and tensile properties of a cast Al-Mg-Fe alloy

Al-Mg alloys are attractive for structural castings owing to their superior strength and ductility in the as-cast state. However, given the tight tolerance for impurities, Al-Mg alloys produced from secondary sources still face multiple challenges. Here, we report the effect of increased Si impurity (0.05–1.6 wt%), which is commonly found in secondary Al sources, on microstructure and tensile properties of a cast Al-4.3Mg-1.6Fe (wt%) alloy, commercially referred to as Castaduct-42 alloy. Microstructural characterization revealed that Si addition increased the volume fraction, size, and aspect ratio of primary Al13Fe4 intermetallic particles as well as the volume fraction of other binary and ternary eutectic phases. Tensile testing results demonstrated that increasing Si impurities from 0.05 to 1.6 wt% reduced ductility from 14.3 ± 1.4 % to 2.2 ± 1.0 %. A particle cracking damage accumulation model coupled with failure analysis indicated primary Al13Fe4 intermetallic particles to be the major contributing factor to the deterioration in ductility with increasing Si content. Additionally, the stabilizing effect of Si on primary Al 13 Fe 4 was inconsistent with the CALPHAD calculation results based on existing CALPHAD databases which predict a slightly decreasing primary Al13Fe4 phase fraction with increasing Si concentration. This work provides new insights into the phase stability and mechanical behavior of the lesser studied Al-Mg-Fe-Si alloy system that will contribute to the development of sustainable cast Al-Mg based alloys.

36 MATERIALS SCIENCE↗

DOE OSTI2023

g-factor engineering with InAsSb alloys toward zero band gap limit

Band gap is known as an effective parameter for tuning the Landé g factor in semiconductors and can be manipulated in a wide range through the bowing effect in ternary alloys. In this work, using the recently developed virtual substrate technique, high-quality InAsSb alloys throughout the whole Sb composition range are fabricated and a large g factor of g≈-90 at the minimum band gap of ~0.1 eV, which is almost twice that in bulk InSb, is found. Further analysis to the zero gap limit reveals a possible gigantic g factor of g≈-200 with a peculiar relativistic Zeeman effect that disperses as the square root of magnetic field. Such a g-factor enhancement toward the narrow gap limit cannot be quantitatively described by the conventional Roth formula, as the orbital interaction effect between the nearly triply degenerated bands becomes the dominant source for the Zeeman splitting. These results may provide insights into realizing large g factors and spin-polarized states in semiconductors and topological materials.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Interaction of beryllium with 316H stainless steel in molten Li 2 BeF 4 (FLiBe)

The increased demand in renewable energy resources has led to a renewed interest in nuclear reactors including a new generation of molten salt reactors. One of the issues encountered in handling of molten chloride or fluoride salts is the inability of metals to form and retain a protective oxide surface layer, generally chromium oxide. The low chromium content, nickel-based alloy INOR-8, later marketed as Hastelloy N, was specifically developed to contain molten fluorides. This alloy had some deficiencies, but its composition resulted in it incurring far less chromium depletion by the molten fluoride salts than alloys like 316 stainless steel. For the next generation of molten salt reactors, an alloy with pressure vessel code approval and higher temperature capability than Hastelloy N is required. Consequently, several reactor designers have reportedly chosen to build the reactor containment vessel from 316H stainless steel. In order to minimize corrosion of the stainless steel by the molten fluoride salt (2LiF-BeF 2 ), it is proposed to add beryllium metal to the salt to react with impurities and provide a means to lower the oxidation potential thus making the salt less corrosive. Even so, there is a concern whether the beryllium would react with components of the stainless steel. To address this concern, static capsule tests were conducted in which selected amounts of beryllium were added to capsules containing 2LiF-BeF 2 (FLiBe) salt and 316H stainless steel and Hastelloy N samples. Following exposure, the samples were cleaned and examined using a variety of analysis techniques including, optical microscopy, SEM-EDS, XPS, LIBS, XRD and EPMA. Tensile samples were also exposed in capsules, and those were subjected to tensile testing. Notably, It was found that for the level of beryllium additions used in this study, intermetallic compounds were formed which could be detrimental to the long-term performance of the 316H stainless steel.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Strengthening model development and effects of low diffusing solutes to coarsening resistance in aluminum alloys

A modified Orowan strengthening model is proposed to account for finite rod-shaped precipitates with hemispherical caps in aluminum alloy systems. A combined computational and experimental approach is used to study the influences of anisotropic Orowan looping and solute-dislocation interaction on temperature-dependent yield strength. Here, the strengthening model is validated with a dataset containing 297 experimental precipitate geometries, chemistries, temperatures, and strength measurements, and achieves a strong predictive correlation of 0.8713 with experimentally measured yield strengths. Under conditions that are applicable to coarsening, constant particle volume fraction and aspect ratio, the model predicts that short rod precipitates provide far superior strengthening effects compared to plate precipitates. A cast Al-Si-Mg-Cu alloy with rod-shaped Q-phase (Al 3 Cu 2 Mg 9 Si 7 ) precipitates was developed with a novel chemistry exploring the use of low-diffusivity elements (Mn, Ni, V, Zr) to limit precipitate coarsening. The thermodynamic behavior of Mn, Ni, V, and Zr across the Q-phase interface is examined using transmission electron microscopy (TEM), first-principles density-functional theory (DFT) calculations. and atom-probe tomography (APT). DFT calculations utilizing TEM identified Q-phase/Al-matrix interfaces show that Mn, Ni, V, and Zr preferentially segregate to the Q-phase precipitate boundaries which suggests inhibition of precipitate coarsening and higher strengths after temperature exposure. Atom-probe tomography confirms solute atom partitioning/segregation at the Q-phase/Al-matrix interface, found in the modified commercial AS7GU alloy (A356 +0.5%Cu), which supports these observations.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Structure and tunable temperature coefficient of magnetization of Mn 4-x Ga x C alloys prepared by induction melting method

The magnetization of most magnetic materials decreases monotonically with increasing temperature. In this work, we found that the temperature coefficient of magnetization of Mn 4-x Ga x C alloys can be tuned from negative values to positive values by controlling the composition x. The antiperovskite type Mn 4-x Ga x C (0.05 ≤ x ≤ 0.75) alloys were prepared by using induction melting method, which is more efficient in large-scale production and obtaining full-density alloys in comparison with the traditional solid-state-reaction method. The values of the temperature coefficient of magnetization of Mn 4-x Ga x C change continuously from negative to positive with decreasing x. The Mn 4-x Ga x C alloys with highly thermal-stable magnetization is expected to present in the composition range of 0.15 < x < 0.25. The saturation magnetization of Mn 4-x Ga x C increases with increasing x, owing to the reduced number of antiferromagnetically coupled Mn atoms at the cubic corner with the face centered Mn atoms. Most Mn 4-x Ga x C alloys with varying x display near-zero remanent magnetization and coercivity at room temperature. The Currie temperature of Mn 4-x Ga x C decreases with increasing x. The x-ray photoelectron spectra of Mn 2p, Ga 2p, and C 1 s reveal distinct splitting due to the diverse chemical states of these atoms at different lattice positions and/or phases. Our work has developed a class of alloys capable of offering a desired temperature coefficient of magnetization across a broad temperature range, thereby offering a method to manipulate the thermodynamics of magnetization.

Magnetic properties↗

DOE OSTI2021

Invited Review Paper in Commemoration of Over 50 Years of Oxidation of Metals: Addressing the Role of Water Vapor on Long-Term Stainless Steel Oxidation Behavior

In the past 20 years, it has become clear that the long-term exposure of chromia-forming austenitic stainless steels to air containing ~ 10 vol% water vapor at 650–800 °C significantly increases the Cr consumption rate compared to laboratory air. However, a similar acceleration does not occur in 100% steam because O 2 is not available to form volatile CrO 2 (OH) 2 . As the research has shown, this accelerated Cr loss is particularly important for thin-walled components like gas turbine recuperators. Typically, conventional austenitic stainless steels exhibit accelerated attack (i.e., rapid formation of Fe-rich oxide nodules), while higher alloyed steels resist this type of degradation until the alloy surface becomes Cr depleted. The development of strategies and solutions for this issue are reviewed. Model Fe–Cr–Ni alloys have been used to study composition effects on this behavior. For example, increasing the Mn content up to ~ 4 wt% was not beneficial, but increasing the Ni content improved oxidation resistance in this environment. However, at 650–700 °C even highly alloyed steels showed surface Cr depletion at alloy grain boundaries resulting in Fe-rich oxide nodule formation. The path forward for this issue will require more refined mechanistic understanding and increased used of modeling to develop better application-specific lifetime models to identify the most cost-effective alloy solutions.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Entropy-driven melting point depression in fcc HEAs

High Entropy Alloys (HEAs) are an increasingly dominant alloy design paradigm. The premise of entropic stabilization of single-phase alloys has motivated much of the research on HEAs. Chemical complexity may indeed help stabilize single alloy phases relative to other lower-entropy competing solid phases. Paradoxically, this complexity may de-stabilize these alloys against the liquid phase, potentially limiting the application space of HEAs at elevated temperatures. In this work, we carry out a comprehensive investigation of the phase stability in the fcc CoCrFeMnNiV-Al HEA space using a state of the art CALPHAD database. By using modern visualization techniques and statistical analysis we examine the trade-off between chemical complexity and stability against the liquid state and identify a potentially difficult to overcome barrier for development of high temperature alloys, at least within the conventional fcc HEA space. Here, limited experimental data seem to be consistent with this analysis.

36 MATERIALS SCIENCE↗

DOE OSTI2025

FY25 Status Update on A709 Code Case Testing at ANL

This report provides an update on the status of the creep rupture testing on the precipitation-treated (PT) Alloy 709 samples fabricated from the first, the second and the third commercial heats, in support of the first, 100,000-hour Alloy 709 Code Case development under the American Society of Mechanical Engineers (ASME) Section III, Division 5 for high-temperature reactor construction. In Fiscal Year (FY) 25, no new tests were initiated, while 5 previously loaded tests were completed. This report presents an overview of the creep-rupture data gathered at Argonne National Laboratory (ANL) since FY21 that totaled 52 completed tests. Metallographic images showing crack morphologies in some representative samples ruptured in FY25 are also included. Key conclusions include: 1) the creep behavior of the three heats of Alloy 709 can be well described by the Larson-Miller relationship; 2) higher temperatures and larger stresses lead to shorter creep life and higher minimum creep rate; 3) Alloy 709 is overall very ductile under creep; 4) the crack morphologies near fracture surfaces are dependent on material’s grain size and test conditions.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

DOE OSTI2020

STEP Report on Advanced ODS FeCrAl Alloys for Fission Applications

Oak Ridge National Laboratory is developing advanced low-Cr oxide dispersion strengthened (ODS) FeCrAl alloys for accident tolerant fuel (ATF) cladding. This report presents the characterization of two new ODS FeCrAl tubes by using powder commercially mechanically alloyed by Zoz GmbH, which underwent high-precision tube rolling with two different annealing schedules. This work shows that the ODS FeCrAl tube without recrystallization exhibits consistent mechanical behavior in comparison with a previously produced tube. The second tube, which underwent a full recrystallization step before the final tube rolling step, showed some circumferential cracking and exhibited limited ductility in the axial tube tensile tests. Based on current and prior work on the ODS FeCrAl alloy system, this report compares the current state of the scientific literature on the alloy class with that of wrought FeCrAl without oxide additions. Then, this report makes recommendations for future research directions that should be undertaken to increase the technology readiness level for ODS FeCrAl as a viable ATF candidate material. This report has been submitted as fulfillment of milestone M3FT-20OR020202064 titled, “STEP Report on Advanced ODS FeCrAl Alloys for Fission Applications” for the US Department of Energy Office of Nuclear Energy’s Advanced Fuel Campaign of the Fuel Cycle R&D program.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2022

Science-Based Acceleration of the Full Value Stream for Metal Additive Manufacturing: Expedited Powder Development and Additive Manufacturing Deployment in the Areas of Ni-Base Superalloy and Custom Alloy Powders for AM

The overall Science-based Acceleration of the Full Value Stream for Metal Additive Manufacturing (AM): Expedited Powder Development and Additive Manufacturing Deployment (“X-P4AM”) project objective is to drastically reduce the time-to-market barriers for new additive alloys of interest in automotive and aerospace applications, through computational alloy design with rapid screening and down- selection via synthesis of candidate alloys with rapid solidification. The project will also refine the technology in high pressure gas atomization to improve the production of commercial quantities of selected powders with high powder yields and enhanced powder quality. Production of modified nickel-based superalloys and a Ni-containing alloy based on a high entropy composition, enhanced powder production methods, and optimized AM build parameterization provided critical steps in widespread adoption of AM technology for aerospace applications, in this case. The individual backgrounds and capabilities of the Parties are ideally suited to the successful execution of this work. The included work enhanced the Contractors’ AM capabilities, a core competency of the Contractors, and develop a close working relationship with the Participant in the areas of nickel-based powder superalloys and custom alloys and their end use.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Science-Based Acceleration of the Full Value Stream for Metal Additive Manufacturing: Expedited Powder Development and Additive Manufacturing Deployment in the Areas of Ni-Base Superalloy and Custom Alloy Powders for AM

36 MATERIALS SCIENCE↗

DOE OSTI2024

In Situ Prediction of Microstructure and Mechanical Properties in Laser-Remelted Al-Si Alloys: Towards Enhanced Additive Manufacturing

Laser surface remelting of aluminum alloys has emerged as a promising technique to enhance mechanical properties through refined microstructures. This process involves rapid cooling rates ranging from 10 3 to 10 8 °C/s, which increase solid solubility within aluminum alloys, shifting their eutectic composition to a larger value of silicon content. Consequently, the resulting microstructure combines a strengthened aluminum matrix with silicon fibers. This study focuses on the laser scanning of Al-Si aluminum alloy to reduce the size of aluminum matrix spacings and transform fibrous silicon particles from micrometer to nanometer dimensions. Analysis revealed that the eutectic structure contained 17.55% silicon by weight, surpassing the equilibrium eutectic composition of 12.6% silicon. Microstructure dimensions within the molten zones, termed ‘melt pools’, were extensively examined using Scanning Electron Microscopy (SEM) at intervals of approximately 20 μm from the surface. A notable increase in hardness, exceeding 50% compared to the base plate, was observed in the melt pool regions. Thus, it is exemplified that laser surface remelting introduces a novel strengthening mechanism in the alloy. Moreover, this study develops an in situ method for predicting melt pool properties and dimensions. A predictive model is proposed, correlating energy density and spectral signals emitted during laser remelting with mechanical properties and melt pool dimensions. This method significantly reduces characterization time from days to seconds, offering a streamlined approach for future studies in additive manufacturing.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Large-Scale, GPU-Enhanced DFTB Approaches for Probing Multi-Component Alloys

The major goals of the project are to develop and apply GPU-enhanced density functional theory tight binding (DFTB) calculations for efficient simulations of structural materials of alloy systems. The figure below depicts the GPU algorithmic developments on the left that will be carried out, and the solid-state structures on the right are representative of the complex alloys that can be computed with the GPU-enhanced DFTB approach. The methodology and tools developed in this project encompass accurate intermolecular potentials and GPU enhancements to the density functional tight binding (DFTB) approach for high-throughput ab initio molecular dynamics calculations of multi-component alloys at elevated temperatures. While classical molecular dynamics can handle hundreds of thousands of atoms, it cannot provide a first-principles based description of large, multi-component alloys at the predictive quantum level. At the other extreme, conventional Kohn-Sham DFT methods can probe the true quantum nature of chemical systems; however, these methods cannot tackle the large sizes relevant to these multi-component systems. The DFTB-based ab initio molecular dynamics approach (coupled with our in-house GPU capabilities for enhanced speed) used in this project provides a viable approach for probing these large systems at a quantum level of detail that is significantly faster than current first-principle methods Collectively, the capabilities developed in this project directly respond to DOE HBCU-OMI, AOI 2-1 initiatives by (1) enabling accurate and efficient predictions and (2) bringing a fundamental understanding of structural interactions in these complex systems at elevated temperatures.

20 FOSSIL-FUELED POWER PLANTS↗

DOE OSTI2023

Alloy designs for high temperature Mo-base systems

For high temperature applications Mo base alloy requirements include both superior structural performance and environmental resistance. To address these requirements alloys in the Mo-Si-B system and refractory multi-principal element alloys (RMPEA) are being developed that exhibit a promising potential, but also have some remaining challenges to improve ductility, lower density and enhance environmental resistance. In the Mo-Si-B system microstructures with a Mo solid solution (Moss) Mo 3 Si and Mo 5 SiB 2 (T2) phases have been the focus of attention. However, the Si solubility in the Moss phase diminishes the ductility and toughness. In order to address this issue a new design based upon Moss, Mo 2 B and T 2 phases lowers the Si solubility in the Moss to improve ductility while the T 2 phase maintains the oxidation performance. Selected additions of Al and Ti enable a density reduction to below 8 g/cm 3 . The RMPEA designs for Mo-rich alloys provide for excellent structural performance, but the complex oxidation products provide no protection. However, in this case a new coating design has been introduced that provides the required environmental resistance.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Develop a new integrated macro→micro←nano (MMN) multiscale modeling framework to optimize high strength aluminum alloys and processes for vehicle light-weighting

Bending tests provide a means to study plane strain fracture performance of 6000 series aluminum alloys. Metrics from bending tests have been correlated with self-pierce riveting (SPR) performance of a high strength AA6111 automotive aluminum alloy in previous works. Using the ORNL HPC resources, this project developed an innovative macro→micro←nano (MMN) multiscale microstructure-based finite element (FE) code to further understanding of the relationship between microstructure and fracture properties of high-strength 6000-series alloys. This work started with microstructural characterization in both mesoscale and nanoscale and bending performance characterization of AA6111 HS2-T6 alloy at Ford, the MMN framework was applied to this alloy to simulate 3-point VDA bending. From the results of the macro-modeling of 3-point VDA bending, the critical region of fracture was identified, and the region geometry was used to construct the micro-model. The fracture criterion of micron-scale precipitates and aluminum matrix which contains submicron and nano particles (AL-SMP-NP) in the micro-model was calibrated and validated by comparing simulated and measured bending results. With the AL-SMP-NP fracture strain obtained, the fracture strain of Al-matrix containing nano particles (ALNP) will similarly be determined by a submicron scale-model using an edge-constrained FE modeling approach developed by Hu et al. With the ALNP fracture strain obtained, the fracture strain of Al-matrix containing no particles will similarly be determined by a nano scale-model using an edge-constrained FE modeling approach. After the MMN framework is built and fracture criterion calibrated, nano-model FE simulations with virtual microstructures was performed to obtain a reduced order model (ROM) of the fracture criterion of the ALNP as a function of volume fraction, size, and distribution of the nanoparticle. This nano→submicron→micro modeling part allows exploration of the influence of different material nanostructures from different process conditions on the bending properties within the multiscale bending simulation framework and the ROM of material bendability as a function of nanoparticle size and shape was established. This obtained reduced order model (ROM) could help guide the design and selection of materials to improve existing SPR process models that could replace trial-and-error rivet/die selection and help to design new rivet/die combinations capable of robustly joining new higher strength 6000 5 series alloys in automotive body structures. This would enable lightweighting of Ford vehicles leading to greater fuel efficiency and reduce manufacturing time and energy.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Revealing High-Temperature Reduction Dynamics of High-Entropy Alloy Nanoparticles via In Situ Transmission Electron Microscopy

Understanding the behavior of high-entropy alloy (HEA) materials under hydrogen (H 2 ) environment is of utmost importance for their promising applications in structural materials, catalysis, and energy-related reactions. Herein, the reduction behavior of oxidized FeCoNiCuPt HEA nanoparticles (NPs) in atmospheric pressure H-2 environment was investigated by in situ gas-cell transmission electron microscopy (TEM). The reduction reaction front was maintained at the external surface of the oxide. During reduction, the oxide layer expanded and transformed into porous structures where oxidized Cu was fully reduced to Cu NPs while Fe, Co, and Ni remained in the oxidized form. In situ chemical analysis showed that the expansion of the oxide layer resulted from the outward diffusion flux of all transition metals (Fe, Co, Ni, Cu). Revealing the H-2 reduction behavior of HEA NPs facilitates the development of advanced multicomponent alloys for applications targeting H 2 formation and storage, catalytic hydrogenation, and corrosion removal.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

DOE OSTI2021

On the existence of orthorhombic martensite in a near-α titanium base alloy used for additive manufacturing

Additive manufacturing is a state-of-the-art production technology to produce tailor-made and highly complex parts. Among various other alloys, Ti base alloys are frequently used in this manufacturing technique due to their well-balanced properties and their wide range of applications. Allotropic phases and the occurrence of athermal phase transformations are the main reasons why these alloys hold a great development potential and are the basis of extensive use. High cooling rates during manufacturing lead to martensitic phases and the formation of nanometer-sized microstructures resulting in extraordinary strength. Simultaneously, such high cooling rates cause a high amount of lattice defects and the occurrence of residual stresses, which finally may result in delamination effects and cracks. Usually, a common approach to reduce residual stresses during additive manufacturing is to decrease thermal gradients by increasing the heat input or preheating the building platform. Instead of applying the typical approaches to lower thermal gradients, this study deals with the origin of the ‘softer’ orthorhombic martensite by accelerating the solidification process. The implementation of the orthorhombic phase in bulk components was inspired by a new phase transformation herein reported for the first time in the powder material, which also validates the possible occurrence of two martensitic phases in the same alloy. Various sophisticated characterization techniques like high energy and high-temperature X-ray diffraction, high-resolution transmission electron microscopy as well as atom probe tomography were applied to characterize this softer orthorhombic martensitic phase in detail aiming to highlight the opportunities accompanied by this new approach for additive manufacturing of titanium alloys.

36 MATERIALS SCIENCE↗