SEARCH · Engineering Papers

Results for “alignment”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17

All sources NASA NTRS DOE OSTI

DOE OSTI2020

Alignment of the ATLAS Inner Detector in Run 2

The performance of the ATLAS Inner Detector alignment has been studied using pp collision data at s√=13TeV collected by the ATLAS experiment during Run 2 (2015–2018) of the Large Hadron Collider (LHC). The goal of the detector alignment is to determine the detector geometry as accurately as possible and correct for time-dependent movements. The Inner Detector alignment is based on the minimization of track-hit residuals in a sequence of hierarchical levels, from global mechanical assembly structures to local sensors. Subsequent levels have increasing numbers of degrees of freedom; in total there are almost 750,000. The alignment determines detector geometry on both short and long timescales, where short timescales describe movements within an LHC fill. The performance and possible track parameter biases originating from systematic detector deformations are evaluated. Momentum biases are studied using resonances decaying to muons or to electrons. The residual sagitta bias and momentum scale bias after alignment are reduced to less than ~0.1 TeV -1 and 0.9×10 -3 , respectively. Impact parameter biases are also evaluated using tracks within jets.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

DOE OSTI2024

Determining tolerance requirements for spray-duct alignment in ducted fuel injection

Several ducted fuel injection (DFI) studies have highlighted the importance of accuracy in aligning the duct axis with that of its corresponding spray for optimal effectiveness, as misalignment adversely impacts the method’s performance. The need for accurate alignment could lead to added manufacturing complexity via tighter tolerances. This study systematically explores cases of horizontal, vertical, and rotational misalignment, analyzing their respective effects on DFI performance. Vertical and horizontal misalignments at the duct inlet plane were varied at magnitudes of 6.25%, 12.5%, and 25.0% of the duct diameter, corresponding to 0.125, 0.25, and 0.5 mm, respectively. Rotational misalignments were set at 1°, 2°, and 4°, corresponding to 3.65%, 7.30%, and 14.6%, respectively, of the duct diameter at its inlet plane. The investigation yields spray-duct alignment tolerance limits and highlights the influence of misalignment direction on emissions due to the interactions with swirl and squish inside the combustion chamber. The results indicate that the tolerance limits for the alignment are within 4° and 0.5 mm relative to the geometrically aligned position. If the misalignment exceeds 4°of rotation or 0.5 mm in the horizontal direction, the beneficial effects on soot reduction using this method are no longer observed. The findings contribute to an understanding that can be used to optimize DFI for cleaner and more efficient combustion in compression-ignition engines.

Şener, Ramazan↗

DOE OSTI2019

Design and alignment of an all-spherical unobscured four-mirror image relay for an ultra-broadband sub-petawatt laser

We describe the design and alignment of an unobscured reflective image relay for use in an ultra-broadband half-petawatt laser system in development at the University of Rochester’s Laboratory for Laser Energetics. The design consists of four spherical mirrors in an unobscured configuration. We show the theoretical basis for such a four-mirror design using first-order optical matrix methods and nodal aberration theory. We also describe the process of aligning this design in a test bed and show the results of this alignment method. We were able to achieve a diffraction-limited nominal design. Furthermore, upon aligning the design in our test bed, we were able to successfully align the design to achieve our target wavefront error of less than 0.3 waves p–v and 0.07 waves rms at the central laser-operating wavelength of 910 nm.

47 OTHER INSTRUMENTATION↗

DOE OSTI2022

Joint iterative reconstruction and 3D rigid alignment for X-ray tomography

X-ray tomography is widely used for three-dimensional structure determination in many areas of science, from the millimeter to the nanometer scale. The resolution and quality of the 3D reconstruction is limited by the availability of alignment parameters that correct for the mechanical shifts of the sample or sample stage for the images that constitute a scan. In this paper we describe an algorithm for marker-free, fully automated and accurately aligned and reconstructed X-ray tomography data. Our approach solves the tomographic reconstruction jointly with projection data alignment based on a rigid-body deformation model. We demonstrate the robustness of our method on both synthetic phantom and experimental data and show that our method is highly efficient in recovering relatively large alignment errors without prior knowledge of a low resolution approximation of the 3D structure or a reasonable estimate of alignment parameters.

36 MATERIALS SCIENCE↗

DOE OSTI2018

NSLS-II Booster Survey and Alignment Systems

This section outlines the survey and alignment requirements and the technology and tools for achieving the NSLS-II equipment positioning goals. The required alignment tolerances are defined primarily by the physics requirements of the accelerator. The tight tolerances dictated by the physics requirements are an order of magnitude tighter than the tolerances of second generation light sources (NSLS) and on level with those at third generation light sources (Soleil, Diamond). These extraordinary position requirements necessitate a concerted R&D engineering effort to identify and develop the survey methodology needed to meet these requirements. As of this date, the methodology is still evolving to balance cost and time constraints while still maintaining the integrity of the survey and alignment systems. State-of-the art equipment including Laser Trackers and Laser Arms have been purchased and used extensively in the pursuit of meeting the NSLS-II survey tolerances. No new technology will need to be developed to meet the alignment requirements but new techniques will be pursued and developed. Survey and alignment provides the foundation for positioning the beam-guiding magnet structures in all 6 degrees of freedom within the required tolerances. Although the tools and instrumentation available for this task have changed over the years and faster and more accurate measurements are possible, only limited control of the environmental conditions is possible. This ultimately sets an upper limit for the achievable measurement and subsequent control network accuracy. At the same time, the control of environmental variables (temperature, humidity) will be fully taken advantage of during the building of NSLS-II , opening up the possibility of ever-increasing accuracy unheard of only five years ago.

42 ENGINEERING↗

DOE OSTI2023

New alignment method for remote protein sequences by the direct use of pairwise sequence correlations and substitutions

Understanding protein sequences and how they relate to the functions of proteins is extremely important. One of the most basic operations in bioinformatics is sequence alignment and usually the first things learned from these are which positions are the most conserved and often these are critical parts of the structure, such as enzyme active site residues. In addition, the contact pairs in a protein usually correspond closely to the correlations between residue positions in the multiple sequence alignment, and these usually change in a systematic and coordinated way, if one position changes then the other member of the pair also changes to compensate. In the present work, these correlated pairs are taken as anchor points for a new type of sequence alignment. The main advantage of the method here is its combining the remote homolog detection from our method PROST with pairwise sequence substitutions in the rigorous method from Kleinjung et al. We show a few examples of some resulting sequence alignments, and how they can lead to improvements in alignments for function, even for a disordered protein.

Jia, Kejue↗

DOE OSTI2021

Mechanical and Dielectric Properties of Aligned Electrospun Fibers

This review paper examines the current state-of-the-art in fabrication of aligned fibers via electrospinning techniques and the effects of these techniques on the mechanical and dielectric properties of electrospun fibers. Molecular orientation, system configuration to align fibers, and post-drawing treatment, like hot/cold drawing process, contribute to better specific strength and specific stiffness properties of nanofibers. The authors suggest that these improved, aligned nanofibers, when applied in composites, have better mechanical and dielectric properties for many structural and multifunctional applications, including advanced aerospace applications and energy storage devices. For these applications, most fiber alignment electrospinning research has focused on either mechanical property improvement or dielectric property improvement alone, but not both simultaneously. Relative to many other nanofiber formation techniques, the electrospinning technique exhibits superior nanofiber formation when considering cost and manufacturing complexity for many situations. Even though the dielectric property of pure nanofiber mat may not be of general interest, the analysis of the combined effect of mechanical and dielectric properties is relevant to the present analysis of improved and aligned nanofibers. A plethora of nanofibers, in particular, polyacrylonitrile (PAN) electrospun nanofibers, are discussed for their mechanical and dielectric properties. In addition, other types of electrospun nanofibers are explored for their mechanical and dielectric properties. An exploratory study by the author demonstrates the relationship between mechanical and dielectric properties for specimens obtained from a rotating mandrel horizontal setup.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

DOE OSTI2017

Radiative Grain Alignment in Protoplanetary Disks: Implications for Polarimetric Observations

We apply the theory of radiative torque (RAT) alignment for studying protoplanetary disks around a T-Tauri star and perform 3D radiative transfer calculations to provide the expected maps of polarized radiation to be compared with observations, such as with ALMA. We revisit the issue of grain alignment for large grains expected in the protoplanetary disks and find that mm-sized grains at the midplane do not align with the magnetic field since the Larmor precession timescale for such large grains becomes longer than the gaseous damping timescale. Hence, for these grains the RAT theory predicts that the alignment axis is determined by the grain precession with respect to the radiative flux. As a result, we expect that the polarization will be in the azimuthal direction for a face-on disk. It is also shown that if dust grains have superparamagnetic inclusions, magnetic field alignment is possible for (sub-)micron grains at the surface layer of disks, and this can be tested by mid-infrared polarimetric observations.

79 ASTRONOMY AND ASTROPHYSICS↗

NASA NTRS1973

Simultaneous particle and field observations of field-aligned currents

Simultaneous measurements of low energy precipitating electrons and magnetic fluctuations from the low altitude polar orbiting satellite OGO-4 have been compared. Analysis of the two sets of experimental data for isolated events led to the classification of high latitude field-aligned currents as purely temporal or purely spatial variations. Magnetic field disturbances calculated using these simple current models and the measured particle fluxes were in good agreement with measured field values. While fluxes of greater than 1 keV electrons are detected primarily on the nightside, magnetometer disturbances indicative of field-aligned currents were seen at all local times, both in the visual auroral regions and dayside polar cusp. Thus electrons with energies less than approximately 1 keV are the prime charge carriers in high latitude dayside field-aligned currents. The satellite measurements are in good agreement with previously measured field-aligned current values and with values predicted from several models involving magnetospheric field-aligned currents.

Berko, F. W.↗

NASA NTRS1974

Field-aligned auroral electron fluxes

Out of a series of five auroral sounding rocket flights, electron fluxes in three of the flights were observed to be sharply field-aligned. The electrons were detected with an array of electrostatic analyzers making 50-point spectral samples from 0 to 15 keV. The field-aligned fluxes resulted in a peak in the spectrum at a lower energy than that of another monoenergetic peak in the spectrum seen consistently when it was conjugate to bright auroral forms giving multiply peaked spectra. The field-aligned peak in the spectrum is apparently a phenomenon distinct from the isotropic peak and was observed to occur at various times in the energy range from a few hundred electron volts to 5 keV. The field-aligned electrons were highly collimated, having pitch angles less than 20 deg and at times less than 10 deg. The high degree of field alignment and the monoenergetic character support the model that these events can be attributed to relatively cool plasma falling through an electric potential at altitudes not too far removed from the rocket.

Arnoldy, R. L.↗

NASA NTRS1977

Development of a method of alignment between various SOLAR MAXIMUM MISSION experiments

Results of an engineering study of the methods of alignment between various experiments for the solar maximum mission are described. The configuration studied consists of the instruments, mounts and instrument support platform located within the experiment module. Hardware design, fabrication methods and alignment techniques were studied with regard to optimizing the coalignment between the experiments and the fine sun sensor. The proposed hardware design was reviewed with regard to loads, stress, thermal distortion, alignment error budgets, fabrication techniques, alignment techniques and producibility. Methods of achieving comparable alignment accuracies on previous projects were also reviewed.

Source record↗

NASA NTRS1978

Relations between transverse electric fields and field-aligned currents

A model for the field-aligned propagation of transverse electric fields and associated field-aligned sheet currents is presented which takes into account the wave nature of the process. The model is applied to the separate cases of ionospheric and magnetospheric sources, and the resulting ionospheric electric field to field-aligned sheet current ratios are determined for comparison with experimental observations. It is found that the magnetospheric wave 'conductivity' for shear mode Alfven waves is small with respect to typical values of the height-integrated ionospheric Pedersen conductivity. For plasma convecting across a stationary disturbance a dynamic equilibrium is achieved in which field-aligned currents flow continuously away from the source on convecting field lines. Consistency with typical ionospheric electric fields requires that the field-aligned sheet currents are limited to around 0.1 A/m for ionospheric polarization sources, while magnetospheric sources are easily capable of 1 A/m or more.

Mallinckrodt, A. J.↗

NASA NTRS1984

The evolution of arguments regarding the existence of field-aligned currents

The present understanding of Birkeland (magnetically-field-aligned) currents was not obtained by a direct, logical course. The story is rather more complex. Starting at the end of the 19th century, the Norwegian scientist Kristian Birkeland laid out a compelling case, supported by both theory and experiment, for the existence of field-aligned currents that cause both the aurora and polar geomagnetic disturbances. Sydney Chapman, the British geophysicist, became the acknowledged leader and opinion maker in the field in the decades following Birkeland's death. Chapman proposed, in contradistinction to Birkeland's ideas, equivalent currents that were restricted to flow in the ionosphere with no vertical or field-aligned components. Birkeland's ideas may have faded completely if it had not been for Hannes Alfven, who became involved well after Chapman's ideas gained predominance. Alfven kept insisting that Birkeland's current system made more sense because field-aligned currents were required to drive most of the ionospheric currents. The author became personally involved when Zmuda et al. (1966) submitted to the Journal of Geophysical Research a paper reporting satellite data showing magnetic disturbances above the ionosphere that were consistent with field-aligned Birkeland currents, but which they did not interpret as being due to such currents.

Dessler, A. J.↗

NASA NTRS1986

A three-dimensional MHD simulation of the interaction of the solar wind with the earth's magnetosphere - The generation of field-aligned currents

The time-dependent interaction of the solar wind with the earth's magnetosphere is simulated using a three-dimensional MHD model. The bow shock, magnetopause, magnetotail, and plasma sheet of the magnetosphere and Birkeland field-aligned currents that are dependent on the polarity of the z component of the IMF are produced. Twin convection cells and a dawn to dusk electric potential of 30-100 kV are detected at the equator in the magnetosphere. Four types of field-aligned currents are observed: region 1, region 2, dayside magnetopause currents in the dayside cusp region, and the dayside cusp currents for southward IMF. Region 1 and 2 field-aligned currents generated for all IMF conditions are 0.6-1.0 x 10 to the 6th A and 0.15-0.61 x 10 to the 6th A, respectively. The relationship between region 1 currents and field-aligned vorticity, and region 2 currents and pressure gradients are studied. The simulated data are compared with a theoretical analysis of the field-aligned currents and good correlation is observed.

Ogino, T.↗

NASA NTRS1987

Alignment and assembly tool for very large diameter cylinders

An alignment and assembly tool is disclosed for aligning the ends of two very large cylinders so that the ends may be welded with a cylindrical strengthening section inserted between the cylinders and aligned and welded into the joint. The tool has a U-shaped main body with a horizontal top section and two legs, which are attached to the ends of the top section and extend outward and downward. Horizontal bottom sections extend outward from the bottoms of two of the legs. The tool has one inner jackscrew and one outer jackscrew on each side of its center, extending downward from the top section. Each of the two bottom sections has an attached side clamp for clamping the alignment tool to two opposing skin stringers of two of the cylinders. The jackscrews are adjusted to bring the edges of a tee ring into precise alignment with the ends of the two large cylinders so that both joints may be welded around their circumference.

Ehl, James H.↗

NASA NTRS1987

The electric field alignment of ice particles in thunderstorms

Electrical and aerodynamic torques on atmospheric ice particles are calculaed in order to assess the degree of alignment of these particles with the electric fields in thunderstorms. In such clouds fields of many tens of kilovolts per meter are commonly measured, and values of 100 to 200 kV/m are not rare. For E = 100 kV/m the calculations indicate that electric field alignment occurs for crystals with major dimensions up to maximum values in the range from 200 microns to 1 mm, depending upon crystal type. Columns are aligned more easily than platelike crystals, except for dendrites which, by virtue of their smaller assumed density, have smaller fall velocities thereby experiencing weaker aerodynamic torques. Thus a substantial degree of alignment is expected for E = 100 kV/m. For E = 10 kV/m only much smaller crystals will be aligned, probably only ones with major dimensions of less than 50 microns or so.

Weinheimer, Andrew J.↗

NASA NTRS1989

The effects of window shape and reticle presence on performance in a vertical alignment task

This study was conducted to evaluate the effect of selected interior work-station orientational cuing upon the ability to align a target image with local vertical in the frontal plane. Angular error from gravitational vertical in an alignment task was measured for 20 observers viewing through two window shapes (square, round), two initial orientations of a computer-generated space shuttle image, and the presence or absence of a stabilized optical alignment reticle. In terms of overall accuracy, it was found that observer error was significantly smaller for the square window and reticle-present conditions than for the round window and reticle-absent conditions. Response bias data reflected an overall tendency to undershoot and greater variability of response in the round window/no reticle condition. These results suggest that environmental cuing information, such as that provided by square window frames and alignment reticles, may aid in subjective orientation and increase accuracy of response in a Space Station proximity operations alignment task.

Rosenberg, Erika L.↗

NASA NTRS1990

Explaining compact groups as change alignments

The physical nature of the apparently densest groups of galaxies, known as compact groups is a topic of some recent controversy, despite the detailed observations of a well-defined catalog of 100 isolated compact groups compiled by Hickson (1982). Whereas many authors have espoused the view that compact groups are bound systems, typically as dense as they appear in projection on the sky (e.g., Williams & Rood 1987; Sulentic 1987; Hickson & Rood 1988), others see them as the result of chance configurations within larger systems, either in 1D (chance alignments: Mamon 1986; Walke & Mamon 1989), or in 3D (transient cores: Rose 1979). As outlined in the companion review to this contribution (Mamon, in these proceedings), the implication of Hickson's compact groups (HCGs) being dense bound systems is that they would then constitute the densest isolated systems of galaxies in the Universe and the privileged site for galaxy interactions. In a previous paper (Mamon 1986), the author reviewed the arguments given for the different theories of compact groups. Since then, a dozen papers have been published on the subject, including a thorough and perceptive review by White (1990), thus more than doubling the amount written on the subject. Here, the author first enumerates the arguments that he brought up in 1986 substantiating the chance alignment hypothesis, then he reviews the current status of the numerous recent arguments arguing against chance alignments and/or for the bound dense group hypothesis (both for the majority of HCGs but not all of them), and finally he reconsiders each one of these anti-chance alignment arguments and shows that, rather than being discredited, the chance alignment hypothesis remains a fully consistent explanation for the nature of compact groups.

Mamon, Gary A.↗