SEARCH · Engineering Papers

Results for “advanced battery development”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17

All sources NASA NTRS DOE OSTI

DOE OSTI2025

Circumventing Radical Generation on Fe–V Atomic Pair Catalyst for Robust Oxygen Reduction and Zinc–Air Batteries

Iron–nitrogen–carbon (Fe–N–C) catalysts are considered the most active platinum-free alternative for oxygen reduction reaction (ORR), yet the generated reactive oxygen species (ROS) from general mechanistic pathway rapidly impair the ORR activity and stability of Fe–N–C. Herein, we establish and report an ORR pathway-switching strategy to circumvent ROS generation and fundamentally improve the activity and stability of Fe–N–C via DFT guided catalyst design. The constructed Fe–V atomic pair catalyst (Fe 1 V 1 -NC) with N 2 Fe-N 2 -VN 2 configuration enables side-on adsorption of O 2 and subsequent direct-breaking of the O═O bond to form O*, thereby avoiding the formation of ROS radicals. Importantly, there is intersite electron interaction between FeN 4 and VN 4 , which further boosts the ORR activity. Consequently, Fe 1 V 1 -NC exhibits outstanding ORR activity with onset and half-wave (E 1/2 ) potentials at 1.02 and 0.89 V versus RHE, respectively, in 0.1 M KOH. Record-high stability is achieved on Fe 1 V 1 -NC with a minimal decay in E 1/2 by 16 mV over 50000 cycles, surpassing Fe–N–C counterpart and most of the catalysts reported to date. The Fe 1 V 1 -NC-based zinc-air battery reported here demonstrates exceptional durability up to 400 h at 10 mA·cm −2 . This work identifies the intrinsic correlation between ORR pathway, activity, and stability, advancing development of stable catalytic systems.

Fe-N-C↗

DOE OSTI2021

Controlling distributed energy resources via deep reinforcement learning for load flexibility and energy efficiency

Behind-the-meter distributed energy resources (DERs), including building solar photovoltaic (PV) technology and electric battery storage, are increasingly being considered as solutions to support carbon reduction goals and increase grid reliability and resiliency. However, dynamic control of these resources in concert with traditional building loads, to effect efficiency and demand flexibility, is not yet commonplace in commercial control products. Traditional rule-based control algorithms do not offer integrated closed-loop control to optimize across systems, and most often, PV and battery systems are operated for energy arbitrage and demand charge management, and not for the provision of grid services. More advanced control approaches, such as MPC control have not been widely adopted in industry because they require significant expertise to develop and deploy. Recent advances in deep reinforcement learning (DRL) offer a promising option to optimize the operation of DER systems and building loads with reduced setup effort. However, there are limited studies that evaluate the efficacy of these methods to control multiple building subsystems simultaneously. Additionally, most of the research has been conducted in simulated environments as opposed to real buildings. This paper proposes a DRL approach that uses a deep deterministic policy gradient algorithm for integrated control of HVAC and electric battery storage systems in the presence of on-site PV generation. The DRL algorithm, trained on synthetic data, was deployed in a physical test building and evaluated against a baseline that uses the current best-in-class rule-based control strategies. Performance in delivering energy efficiency, load shift, and load shed was tested using price-based signals. The results showed that the DRL-based controller can produce cost savings of up to 39.6% as compared to the baseline controller, while maintaining similar thermal comfort in the building. The project team has also integrated the simulation components developed during this work as an OpenAIGym environment and made it publicly available so that prospective DRL researchers can leverage this environment to evaluate alternate DRL algorithms.

24 POWER TRANSMISSION AND DISTRIBUTION↗

DOE OSTI2021

MoS 2 for beyond lithium-ion batteries

As a typical transition-metal chalcogenide material, molybdenum disulfide (MoS 2 ) has received tremendous attention because of its unique layered structure and versatile chemical, electronic, and optical properties. With the focus of this Perspective on the energy storage area, one of the most important contributions of MoS 2 is that it sparked the birth of the rechargeable lithium battery in the early 1980s, which later formed the foundation of commercial lithium batteries. After four decades, admitting that MoS 2 is still playing a significant role in the lithium-ion battery field and considerable effort was made to decipher the mechanism through ex situ and in situ studies and by means of MoS 2 nanostructure engineering that advances the lithium battery performance, it is also used in beyond lithium-ion batteries, such as sodium, magnesium, calcium, and aluminum energy storage systems. Such alternative battery systems are desirable because of the safety concerns of lithium and the depletion of lithium reserves and corresponding increase in cost. In this Perspective, recent development on the fabrication of novel MoS 2 nanostructures was discussed, followed by the scrutinization of their application in beyond lithium-ion batteries and the in situ/operando methods involved in these studies. Finally, a brief summary and outlook that may help with the future advancement of the beyond lithium-ion batteries are presented.

25 ENERGY STORAGE↗

NASA NTRS1981

Power Sources Conference, 29th, Atlantic City, NJ, June 9-12, 1980, Proceedings

Fuel systems are considered along with thermal batteries, primary batteries, lithium primary batteries, lithium/sulfur dioxide primary batteries, lithium/oxychloride primary batteries, high temperature secondary batteries, advanced secondary batteries, and nickel secondary batteries. Attention is given to a Ni-Fe battery with gas recombination device and state-of-charge indication, the development of the nickel-iron battery system for electric vehicle propulsion, improved lead-acid batteries, the behavior of the lead-acid batteries used to start the military vehicles at low temperatures, a life cycle energy analysis of the lead-acid battery, and the anodic corrosion of fiber reinforced lead composites for use in lead-acid submarine batteries. A description is presented of the key physical characteristics for predicting Zr powder burn times, the production of zirconium metal powder for rapid rise time thermal battery application, and high rate lithium-iron disulfide batteries.

Source record↗

NASA NTRS2004

LiCoO2 and SnO2 Thin Film Electrodes for Lithium-Ion Battery Applications

There is an increasing need for small dimension, ultra-lightweight, portable power supplies due to the miniaturization of consumer electronic devices. Rechargeable thin film lithium-ion batteries have the potential to fulfill the growing demands for micro-energy storage devices. However, rechargeable battery technology and fabrication processes have not kept paced with the advances made in device technology. Economical fabrication methods lending excellent microstructural and compositional control in the thin film battery electrodes have yet to be fully developed. In this study, spin coating has been used to demonstrate the flexibility of the approach to produce both anode (SnO2) and cathode (LiCoO2) thin films. Results on the microstructure crystal structure and electrochemical properties of the thin film electrodes are described and discussed.

Maranchi, Jeffrey P.↗

NASA NTRS2023

Solid-State Architecture Batteries for Enhanced Rechargeability and Safety (SABERS): Advanced Battery Technology for Sustainable Aviation

All-electric vertical take-off and landing vehicles (eVTOL) for urban air mobility (UAM) concepts face numerous challenging technical barriers before their introduction into the consumer marketplace. The primary barrier to overcome is developing an energy storage system capable of meeting the rigorous aerospace safety and performance criteria. The performance metrics for eVTOL vehicles are at least two times greater than those of electric ground vehicles. Furthermore, inherently non-flammable batteries are essential for safe operation of commercial electric aerovehicles. The SABERS concept proposes a battery that meets the key performance criteria through development of a solid-state architecture battery utilizing high-capacity sulfur-selenium cathode and lithium metal anode. The combination of sulfur and selenium offers a balanced energy-to-power density ratio, which can be tailored to the specific application by altering the stoichiometric ratios of sulfur to selenium. This hybrid cathode will be developed by implementing NASA patented holey graphene technology as a highly conductive, ultra-lightweight electrode scaffold. A solid-state electrolyte will be used as a safe, non-flammable replacement to the highly flammable liquid organic electrolytes currently used in SOA lithium-ion batteries. This solid-state lithium-sulfur/selenium cell will be designed into a serial stacking configuration to enable dense packaging of the battery cells. The serial stacking configuration is termed a bipolar stack, which has the advantages of reducing overall cell weight, simplifying the interfaced connections for the cell, and minimizing the cooling requirements. Lastly, optimization of battery components will occur through a robust and rigorous combination of various computational modeling techniques covering multiple length scales. The expected result will be a fully solid-state battery with operational temperatures up to 150 °C which provides the required energy density, discharge rates, and inherent safety to meet the strict aerospace mission performance criteria. This presentation will demonstrate a feasible path for solid-state cells that possess a specific energy of greater than 400 Wh/kg to enable electric aircraft. The presentation will also explore novel materials and computational models used to achieve all solid-state cells that operate safely at very high temperatures and specific energies. The cells can withstand damage while operating without an increase in temperature or spontaneous ignition.

Urban Air Mobility (UAM) Vehicles↗

DOE OSTI2020

Perspectives on the relationship between materials chemistry and roll-to-roll electrode manufacturing for high-energy lithium-ion batteries

As lithium-ion battery (LIB) active material and cell manufacturing costs continue to drop with wider adoption of electric vehicles, electrode and cell processing costs remain too high in terms of reaching the ultimate U.S. Department of Energy (DOE) cell cost target of $80/kWh. This paper primarily covers major materials chemistry advancements made over the last 10 years at Oak Ridge National Laboratory (ORNL) in the space of advanced manufacturing science for LIBs with the aim of simultaneously meeting the ultimate cost target, 500 Wh/kg gravimetric energy density, 10-15-min fast charge times, and 1000 deep discharge cycles. Aqeous electrode processing with a variety of active anode and cathode materials is now a standard procedure at the DOE Battery Manufacturing R&D Facility at ORNL (BMF), including the latest processes developed for Ni-rich cathodes. New results on cobalt-free LiNi 0.8 Fe 0.1 Al 0.1 O 2 (NFA 811) are also included and discussed in an electrode processing advantage context. In addition, colloidal processing advancements have been made for Si/C composite anodes for achieving >600 mA h/g capacities. Optimization of electrode coating parameters and drying protocols have been completed, which has elucidated how key processing variables need to be changed when parameters such as slurry solids loading, solvent type, and wet electrode thickness are changed. ORNL has also increased the line speeds at which thick cathodes can be processed using ultra-fast electron beam (EB) curing and substantially decreased formation cycling times to <1 day. Finally, key details of these advancements are discussed in the context of materials chemistry and process-property-performance relationships.

25 ENERGY STORAGE↗

DOE OSTI2021

From Materials to Cell: State-of-the-Art and Prospective Technologies for Lithium-Ion Battery Electrode Processing

Electrode processing plays an important role in advancing lithium-ion battery technologies and has a significant impact on cell energy density, manufacturing cost, and throughput. Compared to the extensive research on materials development, however, there has been much less effort in this area. In this Review, we outline each step in the electrode processing of lithium-ion batteries from materials to cell assembly, summarize the recent progress in individual steps, deconvolute the interplays between those steps, discuss the underlying constraints, and share some prospective technologies. Finally, this Review aims to provide an overview of the whole process in lithium-ion battery fabrication from powder to cell formation and bridge the gap between academic development and industrial manufacturing.

25 ENERGY STORAGE↗

NASA NTRS1998

A Report from the Thermal Science Research Center (TSRC)

A vertical flow loop was designed and assembled to determine the local (circumferential and axial) and mean wall temperature distributions for single-phase and two-phase (subcooled and saturated) downward flow in both uniformly-heated and single-side heated vertical channels. Freon-11 was used as the working fluid in order to directly relate and compare the results with a previous experimental campaign which employed this same working fluid. For a given steady-state experiment, the following parameters were held constant: (1) exit pressure, (2) inlet temperature, and (3) mass velocity. For a given configuration of the 2.2 m long cylindrical channel test section, which had a 1.2 m long heated section, the applied heat rate was varied from zero through successive quasi-steady states to a level which corresponded to localized film boiling in the test section. The measurements showed that the boiling curve changes significantly at higher mass velocities with respect to both the circumferential and axial directions. The slope of the boiling curve changes in a non-monotonic fashion with respect to the circumferential directions. The slope of the boiling curve changes in a non-monotonic fashion with respect to the circumferential direction. The measurements point to the existence of a dry-out phenomenon occurring at multiple levels of the applied heat for the single-side heated channel. In comparing the heat transfer for horizontal channel flow with a vertically downward flow, the results show that significantly lower heat transfer occurs in the horizontal flow. However, this trend reverses as both the Reynolds number and the applied heat rate increase. Both the Liu-Winterton and Shah correlations were compared with the experimental data. The Shah correlation predicted the uniformly heated tube data better. When a thermal hydraulic diameter approach was used for the single-side heated case, the data at upstream locations for Z/L less than 0.5 was bounded above by the Liu-Winterton correlation and below by the Shah correlation. At Z/L = 0.5, the Shah correlation bounded the data; and for Z/L greater than 0.5, both correlations overpredicted the data with the Shah correlation being closest to the data. The present results indicate that additional correlational development is needed. In addressing some of the advanced space thermal management objectives concerning accommodating high heat fluxes in non-uniformly heated systems, a large battery of experiments 88 have been completed where local two-dimensional wall temperature variations were measured for both single-phase and two-phase flow in a single-side heated circular tube. As noted above, the results show significant axial and circumferential variations. Accurately accounting for such variations can result in optimized future advanced space, enhanced (high heat flux) thermal management systems.

Boyd, Ronald D.↗

DOE OSTI2024

Multi-Task with Procter and Gamble (CRADA No. NFE-10-02672)

The purpose of this Cooperative Research and Development Agreement (CRADA) between UT-Battelle, LLC (the “Contractor) and Procter & Gamble Company (the “Participant”) is the development of a research partnership to create new tools, tests and analytical methods to improve the performance, safety and/or environmental quality of chemicals, advanced materials, food products and manufacturing processes. The Participant operates in three global business units: Beauty, Health and Well-Being and Household Care. Some of its worldwide products include Head and Shoulders®, Pantene®, Gillette® razors and personal care products, Crest®, Dawn®, Tide®, Bounty®, Duracell® batteries; and Iams® pet food among others. At its core, however, the Participant is a science driven company. It supports one of the most robust industrial research and development (R&D) programs in the world. The Participant uses this rich foundation of science to drive innovation across all of its product lines. But the innovation process is not confined in-house The Participant pursues an “open innovation” policy, seeking partnerships with scientists and researchers in universities and national laboratories where it can contribute its extensive knowledge assets and collaborate to advance scientific understanding. The research under this multi-task CRADA was directed under the following general task areas and, throughout the duration of this CRADA the work statement was modified to match the needs of the Parties and the direction of the research. (1) Software modeling, simulation and development; (2) Manufacturing Technologies; (3) Supply Chain Optimization, (4) Advanced Materials.

36 MATERIALS SCIENCE↗

DOE OSTI2026

Advanced Power Electronics and Electric Machines

NLR's advanced power electronics and electric machines (APEEM) research group develops world-class experimental and modeling capabilities to design and evaluate efficient and reliable power electronics and electric machines, as well as innovative thermal management systems to maximize their performance. They also design, fabricate, and characterize advanced power electronics packaging and are developing state-of-health monitoring techniques.

25 ENERGY STORAGE↗

NASA NTRSDate not supplied

On-Demand Manufacturing of Electronics

The On-Demand Manufacturing of Electronics (ODME) project develops materials, processes, and device designs to enable electronics, sensors, and semiconductors to be produced in microgravity environments. The demonstration of these technologies provides a pathway for space-based manufacturing of circuits, wearables, energy storage devices, and other electronics. This has facilitated the terrestrial production of devices including a wide range of sensors, printed batteries, and circuits that are additively manufactured using techniques available on the Advanced Toolplate System (ATS). Recent parabolic flight campaigns conducted with the ATS suggest that direct ink write (DIW) technology is suitable for depositing functional material inks in reduced gravity environments. The development of the Advanced Toolplate system also includes several other new tools, including miniaturized versions of the direct write head, fused filament fabrication head, micro-mill, component pick & place head, and two newly developed deposition technologies, the Electrohydrodynamic (EHD) inkjet head (for semiconductors), and the Electrodeposition head (for high performance circuits). These experiments are designed to compare processing and material behavior in zero gravity versus ground-based data for validation of microgravity advantages and de-risking of future orbital demonstrations of these technologies. The ability to conduct experiments in microgravity is a pivotal step in enabling electronic manufacturing technology in space for both terrestrial and deep space applications.

Cadre Francis↗

DOE OSTI2023

Tin Metal Improves the Lithiation Kinetics of High-Capacity Silicon Anodes

Si-based anodes present a great promise for high energy density lithium-ion batteries. However, its commercialization is largely hindered by a grand challenge of a rapid capacity fade. Here, we demonstrate excellent cycling stability on a Si-Sn thin film electrode that outperforms pure Si or Sn counterpart under the similar conditions. Combined with the first-principles calculations, in situ transmission electron microscopy studies reveal a reduced volume expansion, increased conductivity, as well as dynamic rearrangement upon lithiation of the Si-Sn film. Here we attribute the improved lithiation kinetics to the formation of a conductive matrix that comprises a mosaic of nanostructured Sn, Li y Sn (specifically, Li 7 Sn 2 develops around the lithiation potential of Si), and Li x Si. This work provides an important advance in understanding the lithiation mechanism of Si-based anodes for next-generation lithium-ion batteries.

25 ENERGY STORAGE↗

DOE OSTI2022

Forum on Materials and Interfaces for Energy Storage and Conversion

This ACS Applied Materials & Interfaces forum on energy storage and conversion contains the topics of research discoveries to advance energy technology development. The topics are focused on the efficient and sustainable use of energy in the fields of fuel cells, CO 2 conversion, water splitting, batteries, and electrochemical capacitor. This forum highlights recent achievements in these emerging technologies through the design and evaluation of novel materials and devices and theoretical study. Additionally, this forum also showcases the technology at all stages of development from “embryonic” conception to industrial adaptation.

25 ENERGY STORAGE↗

NASA NTRS1980

Electric and hybrid vehicle system R/D

The work being done to characterize the level of current propulsion technology through component testing is described. Important interactions between the battery and the propulsion system will be discussed. Component development work, involving traction motors, motor controllers and transmissions are described and current results are presented. Studies of advanced electric and hybrid propulsion system studies are summarized and the status of propulsion system development work supported by the project is described. A strategy for fostering joint industry/government projects for commercialization of propulsion components and systems is described briefly.

Schwartz, H. J.↗

DOE OSTI2020

Advanced electrolytes for fast-charging high-voltage lithium-ion batteries in wide-temperature range

LiNixMnyCo1-x-yO2 (NMC) cathode materials with Ni=0.8 have attracted great interest for application in high energy-density lithium (Li)-ion batteries (LIBs) because of their high specific capacities at high voltages. However, the practical application of Ni-rich NMC in LIBs under high charge voltages (e.g. 4.4 V and above) still faces big challenges due to the severe capacity fading, which is directly related to the instability of the cathode/electrolyte interface. In this work, we develop new localized high-concentration electrolytes (LHCEs) based on carbonate solvents, which are compatible with graphite (Gr) anode and have a high oxidation potential over 4.9 V vs. Li/Li+. The optimal LHCE enables the Gr||NMC811 cells with 2.8 mAh cm-2 cathode areal capacity loading to achieve an excellent cycling stability over 600 cycles with a capacity retention of 94.2 % under a charge cut-off voltage of 4.4 V at 25 ?C, good rate capabilities under fast charging or discharging up to 3C rate, and superior low-temperature discharge performance down to -30 ?C with a capacity retention of 85.6% at C/5 rate. The findings in this work shed light a very promising strategy to develop new electrolytes for practical high-energy LIBs with Ni-rich NMC cathodes.

Zhang, Xianhui↗

DOE OSTI2021

Integration of a DER Management System in Riverside. Final report

The tasks in this project covered various aspects, including algorithm development, algorithm integration into a commercial Active Network Management (ANM) platform, hardware-in-the-loop (HIL) testing in an industry-standard testing platform, pilot demonstration in Riverside, California, and also cost and benefit analysis. The DERMS platform in this project can host different algorithms developed on different platforms (e.g., MATLAB and Python) and it can interact with different hardware devices (e.g., different PV inverters, battery inverters, and different sensors). The DER control solution are based on an advanced model-free, layered, and clustered DER control paradigm. At the core of the DER control algorithms was the concept of Extremum Seeking (ES), which is a model-free probing-based control technique. The ES-based control algorithms were tested on major real-world inverters; both individually and in a cluster. It was shown that even legacy equipment (or when paired with a few additional advanced equipment) can support such advanced control. The monitoring algorithms utilize a heterogeneous set of legacy and advanced sensor measurements, such as behind-the-meter DER sensors, distribution-level Phase Measurement Units, distribution-substation Supervisory Control and Data Acquisition (SCADA), and line current sensors, with their limited availability; in order to infer practical network conditions. Sensor data are utilized to achieve resource forecasting, phase identification, and distribution system state estimation. The technology that was developed and demonstrated in this project could be transformational to utilities, including the smaller municipal utilities such as in Riverside, which may not have the resources to deploy advanced distribution system and DERMS solutions in order to support high penetration of solar power integration. This project created a real-world prototype to provide utilities with an assessment of smart grid monitoring and control technologies.

24 POWER TRANSMISSION AND DISTRIBUTION↗

DOE OSTI2023

Engineered Wood: Sustainable Technologies and Applications

Natural wood has been used for construction, fuel, and furniture for thousands of years because of its versatility, renewability, and aesthetic appeal. However, new opportunities for wood are arising as researchers have developed ways to tune the material's optical, thermal, mechanical, and ionic transport properties by chemically and physically modifying wood's naturally porous structure and chemical composition. Such modifications can be used to produce sustainable, functional materials for various emerging applications such as automobiles, construction, energy storage, and environmental remediation. In this review, we highlight recent advancements in engineered wood for sustainable technologies, including thermal and light management, environmental remediation, nanofluidics, batteries, and structural materials with high strength-to-weight ratios. Additionally, the current challenges, opportunities, and future of wood research are discussed, providing a guideline for the further development of next-generation, sustainable wood-based materials.

36 MATERIALS SCIENCE↗