SEARCH · Engineering Papers

Results for “active insulation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17

All sources NASA NTRS DOE OSTI

NASA NTRS2013

Acoustic and Thermal Testing of an Integrated Multilayer Insulation and Broad Area Cooling Shield System

A Multilayer Insulation (MLI) and Broad Area Cooling (BAC) shield thermal control system shows promise for long-duration storage of cryogenic propellant. The NASA Cryogenic Propellant Storage and Transfer (CPST) project is investigating the thermal and structural performance of this tank-applied integrated system. The MLI/BAC Shield Acoustic and Thermal Test was performed to evaluate the MLI/BAC shield's structural performance by subjecting it to worst-case launch acoustic loads. Identical thermal tests using Liquid Nitrogen (LN2) were performed before and after the acoustic test. The data from these tests was compared to determine if any degradation occurred in the thermal performance of the system as a result of exposure to the acoustic loads. The thermal test series consisted of two primary components: a passive boil-off test to evaluate the MLI performance and an active cooling test to evaluate the integrated MLI/BAC shield system with chilled vapor circulating through the BAC shield tubes. The acoustic test used loads closely matching the worst-case envelope of all launch vehicles currently under consideration for CPST. Acoustic test results yielded reasonable responses for the given load. The thermal test matrix was completed prior to the acoustic test and successfully repeated after the acoustic test. Data was compared and yielded near identical results, indicating that the MLI/BAC shield configuration tested in this series is an option for structurally implementing this thermal control system concept.

Wood, J. J.↗

NASA NTRS2013

Acoustic and Thermal Testing of an Integrated Multilayer Insulation and Broad Area Cooling Shield System

Wood, Jessica J.↗

NASA NTRS2001

Mapping Rice Production in China with AVHRR Imagery

The study of rice agriculture is necessary for both the importance of rice as a vital food source and because of the fact that cultivating it has an unfortunate byproduct, namely methane gas. As a food source, rice is a staple for a large majority of the world's population, especially in Asia. Because the populations of many Asian nations are increasing at rapid rates, the production of rice will need to similarly increase. In 1989, it was estimated that the demand for rice would increase by 65% by the year 2019. Rice crops are considered to be one of the primary anthropogenic sources of methane gas. A reason for concern is that this gas is a so-called "greenhouse" trace gas and given its increasing levels in the atmosphere, is thought to contribute to the suspected global warming phenomenon. Some estimate that methane may contribute up to 20% to the global warming effect. Trace gas emissions from anthropogenic sources is an issue that generates great worldwide interest because of the fact that mankind is very likely affecting the current and future climate in potentially negative ways. In an effort to better understand these effects, scientists and engineers are conducting research on all of the varied fronts which relate to climate change and biosphere/atmosphere interactions. The study of global warming through increasing concentrations of greenhouse gases is one area which has received much media and scientific attention. Research fueled by debates on this topic is being conducted on numerous, interrelated fronts in an effort to better understand the complex relationship between human activities and the earth's climate. The research ranges from attempting to verify if the observed data even supports the existence of an anthropogenically generated global-warming phenomenon, to identification of sources and sinks of the trace gases, to measuring the source strengths, to studies which focus on modeling the processes which generate the gases, and finally, to trying to project their impact on the global climatic system. Some of the more commonly known sources of greenhouse gases are related to industry and transportation. Carbon dioxide, CO2, from automobile emissions is one such example. Lesser known are sources from natural and cultivated vegetation, such as the methane, CH4, resulting from rice cropping. While the concentration of atmospheric methane is significantly less than that of carbon dioxide, CH4 has been estimated to have up to 32 times the insulating capability of carbon dioxide, making it an important gas to monitor. The remainder of this chapter will provide some additional background information on the effects of atmospheric methane, and the role that rice agriculture plays as a source in the methane budget. This will be followed by a brief description of efforts to model this source of atmospheric methane. Finally, this chapter will end with a statement of the hypotheses of this thesis, at which time a description of the information contained in the rest of this document will be provided.

Paliouras, Eleni J.↗

NASA NTRS2010

High-Altitude Hydration System

Three methods are being developed for keeping water from freezing during high-altitude climbs so that mountaineers can remain hydrated. Three strategies have been developed. At the time of this reporting two needed to be tested in the field and one was conceptual. The first method is Passive Thermal Control Using Aerogels. This involves mounting the fluid reservoir of the climber s canteen to an inner layer of clothing for better heat retention. For the field test, bottles were mounted to the inner fleece layer of clothing, and then aerogel insulation was placed on the outside of the bottle, and circumferentially around the drink straw. When climbers need to drink, they can pull up the insulated straw from underneath the down suit, take a sip, and then put it back into the relative warmth of the suit. For the field test, a data logger assessed the temperatures of the water reservoir, as well as near the tip of the drink straw. The second method is Passive Thermal Control with Copper-Shielded Drink Straw and Aerogels, also mounted to inner layers of clothing for better heat retention. Braided wire emanates from the inside of the fleece jacket layer, and continues up and around the drink straw in order to use body heat to keep the system-critical drink straw warm enough to keep water in the liquid state. For the field test, a data logger will be used to compare this with the above concept. The third, and still conceptual, method is Active Thermal Control with Microcontroller. If the above methods do not work, microcontrollers and tape heaters have been identified that could keep the drink straw warm even under extremely cold conditions. Power requirements are not yet determined because the thermal environment inside the down suit relative to the external environment has not been established. A data logger will be used to track both the external and internal temperatures of the suit on a summit day.

Parazynski, Scott E.↗

NASA NTRSDate not supplied

Metallic Vs Inflatable Primary Structure: A Comprehensive Trade for a Mars Transit Habitat

Large diameter inflatable habitat solutions are hypothesized to have an advantage over traditional metallic habitats of equal volume and functional requirements in terms of minimizing mass. A fair and comprehensive trade of metallic primary structure versus inflatable softgoods primary structure for a Mars Transit Habitat was conducted by The Boeing Company under the NASA Next Space Technologies for Exploration Partnerships-2 (NextSTEP-2)Appendix A contract in order to determine the minimum mass option from a system level. A Mars Transit Habitat is a major system mass driver because small increases in the mass can create large mass changes in the propulsive stage, adding complexity and cost to the mission. Three different vehicle configurations were traded using a fixed volume constraint and the same Ground Rules and Assumptions(GR&A)provided by NASA. The configurations were 1) 5.5 m diameter metallic habitat, 2) 7.0 m diameter metallic habitat, and 3) 7.63 m diameter inflatable habitat. In order to complete the trade, each configuration was analyzed and sized, but a system level approach had to be taken to ensure other aspects and subsystems besides the structure were captured. The primary functions (i.e. restraint layer, bladder, multilayer insulation [MLI], micro-meteoroid orbital debris [MMOD]) and strength advantages of softgoods are well understood, but there were other system level impacts that were discovered or addressed that are unique to softgoods. For the metallic structure, a modern and mass optimal material and manufacturing process was adopted to ensure the lightest weight options were evaluated. Two different aluminium lithium structures were evaluated, a longer length 5.5 m diameter and a shorter length 7 m diameter structure. The trade demonstrates that each configuration is feasible and close to the target dry mass for the Mars Transit Habitat Trans-Martian Injection burn. System level mass was the primary consideration, but since the three concepts were close in total mass, a clear winner did not arise. Secondary factors were evaluated such as architecture habitability (human factors), development considerations, on-orbit activation and outfitting, extensibility to other applications, and configuration flexibility. The aggregation of the lowest mass, most benefits, and fewest challenges resulted in the 5.5m diameter metallic configuration being the most favorable.

Matthew Ziglar↗

NASA NTRS1982

A preliminary assessment of the self-induced environment and contamination of the Space Telescope

Preliminary estimates for the internal pressures and surface contamination of the Space Telescope were made. The calculations for the transient pressures in the aft-shroud and telescope compartments considered two large communicating volumes that contain gaseous sources and sinks. The outgassing sources in the aft shroud consist of several scientific instruments, paints, insulations, and graphite-epoxy structures. With the exception of the instruments, these sources also exist in the telescope compartment. the outgassing functions were generated from ample test results at various temperatures and from internal pressure measurements in a vacuum test of one of the instruments. The venting occurs through combinations of series and parallel passages in both compartments. The calculated time constant of the two volumes and their respective passages, with the telescope protective door closed, is a few seconds, which is slightly less than that of the shuttle bay volume with the bay doors closed. With the telescope door closed, the pressures in the two compartments should decay to about 1OE-5 torr in about 200 hours. The contaminant deposits were assessed on the basis of expected partial pressures of the contaminant fraction of the outgassing. These pressures and the activation energies of the source materials were used to calculate the adsorbed and condensed deposits on the surfaces as a function of time.

Scialdone, J. J.↗

NASA NTRS2005

Actively Cooled SLMS(TM) Technology for HEL Applications

Mr. Jacoby is the Chief Scientist for Schafer's Lightweight Optical Systems business area with twenty four years experience in laser and optical systems for space and military applications. He and colleague Dr. Goodman conceived and developed Silicon Lightweight Mirrors (SLMS(TM)) technologies for space applications from the extreme UV to FAR IR wavelengths. Schafer has demonstrated two different methods for actively cooling our Silicon Lightweight Mirrors (SLMS(TM)) technology. Direct internal cooling was accomplished by flowing liquid nitrogen through the continuous open cell core of the SLMS(TM) mirror. Indirect external cooling was accomplished by flowing liquid nitrogen through a CTE matched Cesic square-tube manifold that was bonded to the back of the mirror in the center. Testing was done in the small 4-foot thermal/vacuum chamber located at the NASA/MSFC X-Ray Calibration Facility. Seven thermal diodes were located over the front side of the 5 inch diameter mirror and one was placed on the outlet side of the Cesic manifold. Results indicate that the mirror reaches steady state at 82K in less than four minutes for both cooling methods. The maximum temperature difference of the eight diodes was less than 200 mK when the mirror was internally cooled and covered with MLI to insulate it from the large 300 K aluminum plate that was used to mount it.

Jacoby, Marc T.↗

NASA NTRS1989

Flight Motor Set 360L003 (STS-29R)

The redesigned solid rocket motor (RSRM) flight set 360L003 was launched on March 13, 1989 as part of NASA space shuttle mission STS-29R. As was the case with flight sets 360L001 and 360L002 (STS-26R and STS-27R), both motors (360L003A and 360L003B) performed in an excellent manner. Evaluation of the ground environment instrumentation measurements verified thermal model analysis data and showed agreement with predicted environmental effects. The right-hand aft field joint primary heater failed during the countdown; the secondary heater was activated and performed as designed. All other field joint heaters and aft skirt thermal conditioning systems had no anomalies. Shuttle thermal imager infrared readings compared favorably with measured ground environment instrumentation data. No thermal launch commit criteria violations occurred at any time. Evaluation of the development flight instrumentation showed exceptional propulsion performance. All ballistic parameters closely matched the predicted values and were well within the required specification levels. Girth and biaxial strain gage measurements compared closely with corresponding gages on previous flight motors, static tests, and with preflight predictions. Adequate safety factors were verified. (Some ignition transient spiking was noted in a few girth gages; the spiking was determined not to be representative of actual case behavior, but an instrumentation phenomena.) The accelerometers again measured high vibration amplitude levels during the ignition transient and the reentry Max Q phases. Postflight inspection showed that all combustion gas was contained by the insulation in the field and case-to-nozzle joints. No anomalous insulation erosion patterns were found, and the seals that did directly contain motor pressure showed no heat effects, erosion, or blowby. All anomalies identified were a result of splashdown damage, with the exception of fretting in the case field joint interference (nonsealing) surfaces and a prelaunch field joint heater failure. The disposition of all anomalies and the complete results are reported.

Riehr, Glen A.↗

NASA NTRS1986

Energy yields in the prebiotic synthesis of hydrogen cyanide and formaldehyde

Prebiotic experiments are usually reported in terms of carbon yields, i.e., the yield of product based on the total carbon in the system. These experiments usually involve a large input of energy and are designed to maximize the yields of product. However, large inputs of energy result in multiple activation of the reactants and products. A more realistic prebiotic experiment is to remove the products of the activation step so they are not exposed a second time to the energy source. This is equivalent to transporting the products synthesized in the primitive atmosphere to the ocean, and thereby protecting them from destruction by atmospheric energy sources. Experiments of this type, using lower inputs of energy, give energy yields (moles of products/joule) which can be used to estimate the relative importance of the different energy sources on the primitive earth. Simulated prebiotic atmospheres containing either CH4, CO or CO2 with N2, H2O and variable amounts of H2 were subjected to a high frequency Tesla coil. Samples of the aqueous phase were taken at various time intervals from 1 hr to 7 days, and the energy yields were obtained by extrapolation to zero time. The samples were analyzed for HCN with the cyanide electrode and for H2CO by chromotropic acid. The spark energy was estimated by calorimetry. The temperature rise in an insulated discharge flask was compared with the temperature rise from a resistance heater in the same flask. These results will be compared with calculated production rates of HCN and H2CO from lightning and a number of photochemical processes on the primitive Earth.

Stribling, R.↗

NASA NTRS1995

Adiabatic charging of nickel-hydrogen batteries

Battery management during prelaunch activities has always required special attention and careful planning. The transition from nickel-cadium to nickel-hydrogen batteries, with their high self discharge rate and lower charge efficiency, as well as longer prelaunch scenarios, has made this aspect of spacecraft battery management even more challenging. The AXAF-I Program requires high battery state of charge at launch. The use of active cooling, to ensure efficient charging, was considered and proved to be difficult and expensive. Alternative approaches were evaluated. Optimized charging, in the absence of cooling, appeared promising and was investigated. Initial testing was conducted to demonstrate the feasibility of the 'Adiabatic Charging' approach. Feasibility was demonstrated and additional testing performed to provide a quantitative, parametric data base. The assumption that the battery is in an adiabatic environment during prelaunch charging is a conservative approximation because the battery will transfer some heat to its surroundings by convective air cooling. The amount is small compared to the heat dissipated during battery overcharge. Because the battery has a large thermal mass, substantial overcharge can occur before the cells get too hot to charge efficiently. The testing presented here simulates a true adiabatic environment. Accordingly the data base may be slightly conservative. The adiabatic charge methodology used in this investigation begins with stabilizing the cell at a given starting temperature. The cell is then fully insulated on all sides. Battery temperature is carefully monitored and the charge terminated when the cell temperature reaches 85 F. Charging has been evaluated with starting temperatures from 55 to 75 F.

Lurie, Chuck↗

NASA NTRS1997

High Temperature Structural Foam

The Aerospace Industry is experiencing growing demand for high performance polymer foam. The X-33 program needs structural foam insulation capable of retaining its strength over a wide range of environmental conditions. The High Speed Research Program has a need for low density core splice and potting materials. This paper reviews the state of the art in foam materials and describes experimental work to fabricate low density, high shear strength foam which can withstand temperatures from -220 C to 220 C. Commercially available polymer foams exhibit a wide range of physical properties. Some with densities as low as 0.066 g/cc are capable of co-curing at temperatures as high as 182 C. Rohacell foams can be resin transfer molded at temperatures up to 180 C. They have moduli of elasticity of 0.19 MPa, tensile strengths of 3.7 Mpa and compressive strengths of 3.6 MPa. The Rohacell foams cannot withstand liquid hydrogen temperatures, however Imi-Tech markets Solimide (trademark) foams which withstand temperatures from -250 C to 200 C, but they do not have the required structural integrity. The research activity at NASA Langley Research Center focuses on using chemical blowing agents to produce polyimide thermoplastic foams capable of meeting the above performance requirements. The combination of blowing agents that decompose at the minimum melt viscosity temperature together with plasticizers to lower the viscosity has been used to produce foams by both extrusion and oven heating. The foams produced exhibit good environmental stability while maintaining structural properties.

Weiser, Erik S.↗

NASA NTRS2018

NASA Low-Power Stirling Convertor for Small Landers, Probes, and Rovers Operating in Darkness

A variety of mission concepts have been studied by NASA and the U. S. Department of Energy that would utilize low power Radioisotope Power Systems (RPS) for landers, probes, and rovers. These missions would contain science measuring instruments distributed across planetary surfaces or near objects of interest where solar flux is insufficient for using solar cells. Landers could be used to provide data like wind, temperature, pressure, seismic activity, and other planetary measurements to mission planners or future explorers. The studies proposed using fractional versions of the General Purpose Heat Source (GPHS) or multiple Light Weight Radioisotope Heater Units (LWRHU) to heat power conversion technologies for science instruments and communication. Dynamic power systems are capable of higher conversion efficiencies, which could enable equal power using less fuel or more power using equal fuel, when compared to less efficient static power conversion technologies. Providing spacecraft with more power would decrease duty cycling of basic functions and, therefore, increase the quality and abundance of science data. Low power Stirling convertors are being developed at NASA Glenn Research Center (GRC) to provide future micro spacecraft with electrical power by converting heat from one or more LWRHUs. An initial design converts multiple Watts of heat to one Watt of electrical power output using a Stirling convertor. Development of the concept includes maturation of convertor and controller designs, performance evaluation of an evacuated metal foil insulation, and development of system interfaces.

Wilson, Scott D.↗

NASA NTRS2018

NASA Low Power Stirling Convertor for Small Landers, Probes, and Rovers Operating in Darkness

Wilson, Scott↗

NASA NTRS2018

NASA Low Power Stirling Convertor for Small Landers, Probes, and Rovers Operating in Darkness

A variety of mission concepts have been studied by NASA and the U. S. Department of Energy that would utilize low power Radioisotope Power Systems (RPS) for probes, landers rovers, and repeaters. These missions would contain science instruments distributed across planetary surfaces or near objects of interest where solar flux is insufficient for using solar cells. Landers could be used to provide data like radiation, temperature, pressure, seismic activity, and other surface measurements for planetary science and to inform future mission planners. The studies proposed using fractional versions of the General Purpose Heat Source (GPHS) or multiple Light Weight Radioisotope Heater Units (LWRHU) to heat power conversion technologies for science instruments and communication. Dynamic power systems are capable of higher conversion efficiencies, which could enable equal power using less fuel or more power using equal fuel, when compared to less efficient static power conversion technologies. Providing spacecraft with more power would decrease duty cycling of basic functions and, therefore, increase the quality and abundance of science data. Low power Stirling convertors are being developed at NASA Glenn Research Center (GRC) to provide future micro spacecraft with electrical power by converting heat from one or more LWRHUs. An initial design converts multiple watts of heat to one watt of electrical power output using a Stirling convertor. Development of the concept includes maturation of convertor and controller designs, performance evaluation of an evacuated metal foil insulation, and development of system interfaces. Demonstration of the convertor is planned and represents a new class of RPS with power levels an order of magnitude lower than previous practical designs.

Wilson, Scott D.↗

NASA NTRSDate not supplied

Inflatable Softgoods Testing Capability Development for Habitation

The Habitation Systems Development Office (HP40) at NASA Marshall Space Flight Center supports systems engineering, integration, and project management for next generation space habitats. The office is responsible for formulation activities for Lunar Surface Habitat and Mars Transit Habitat. HP40 also manages commercial partnerships for exploration habitat development. The Lunar Surface Habitat is intended to initially support a minimum of two crew on the lunar surface for an approximately 30-day mission, with the ability to accommodate four crew for short durations. The Mars Transit Habitat will transport four crew to and from Mars orbit on a potentially 1,200 day mission. Both concepts are envisioned to leverage inflatable softgoods as the primary structural material for the habitation portion of the architecture. Inflatable softgoods are a complex, multi-material system consisting of multiple layers which perform specific functions. A bladder layer (polymer) contains the habitat’s atmosphere. The bladder is indexed to a woven restraint layer, usually Kevlar or Vectran, which serves as the structural layer. The remaining outer layers are for micro-meteoroid orbital debris (MMOD) shielding, protection from atomic Oxygen (if the material system is to be deployed in low earth orbit), and thermal insulation. The primary advantage of inflatable softgoods is that they can offer a larger volume per unit mass relative to a rigid metal structure. Inflatable softgoods have a strong development heritage within NASA, beginning with work in the 1960s in partnership with Goodyear Aerospace and continuing with Johnson Space Center’s TransHab project in the 1990s . Some development efforts subsequently transitioned into the private sector to mature the material technology for flight applications, including human habitation. In August 2022, NASA published its guidelines for certification of crewed inflatable softgoods structures (JSC-67721). This document outlines a series of tests which will be needed to certify inflatable softgoods material systems for use in crewed mission applications. It includes burst testing at the subscale and full-scale to determine the ultimate burst pressure of the softgoods architecture. Creep (long term deformation of the material under stress) is a key failure mode which must be characterized. Creep testing at the component and module levels is also recommended to generate time to failure curves and verify that the inflatable system has a predicted operational life which exceeds mission parameters. ET (Test Engineering) at MSFC and HP40 have worked together to establish softgoods testing capabilities for the center. This includes the ability to conduct module level burst tests and creep tests. The poster will highlight these capabilities and provide examples of testing which has been performed to date by ET. NASA MSFC anticipates that these test capabilities will continue to offer critical support for companies pursuing inflatable softgoods for exploration applications (lunar surface habitation, Mars transit) as well as commercial low earth orbit platforms.

habitation↗

NASA NTRS2006

NASA Tech Briefs, November 2006

Topics include: Simulator for Testing Spacecraft Separation Devices; Apparatus for Hot Impact Testing of Material Specimens; Instrument for Aircraft-Icing and Cloud-Physics Measurements; Advances in Measurement of Skin Friction in Airflow; Improved Apparatus for Testing Monoball Bearings; High-Speed Laser Scanner Maps a Surface in Three Dimensions; Electro-Optical Imaging Fourier-Transform Spectrometer; Infrared Instrument for Detecting Hydrogen Fires; Modified Coaxial Probe Feeds for Layered Antennas; Detecting Negative Obstacles by Use of Radar; Cryogenic Pound Circuits for Cryogenic Sapphire Oscillators; PixelLearn; New Software for Predicting Charging of Spacecraft; Conversion Between Osculating and Mean Orbital Elements; Generating a 2D Representation of a Complex Data Structure; Making Activated Carbon by Wet Pressurized Pyrolysis; Composite Solid Electrolyte Containing Li+- Conducting Fibers; Electrically Conductive Anodized Aluminum Surfaces; Rapid-Chill Cryogenic Coaxial Direct-Acting Solenoid Valve; Variable-Tension-Cord Suspension/Vibration- Isolation System; Techniques for Connecting Superconducting Thin Films; Versatile Friction Stir Welding/Friction Plug Welding System; Thermal Spore Exposure Vessels; Enumerating Spore-Forming Bacteria Airborne with Particles; Miniature Oxidizer Ionizer for a Fuel Cell; Miniature Ion-Array Spectrometer; Promoted-Combustion Chamber with Induction Heating Coil; Miniature Ion-Mobility Spectrometer; Mixed-Salt/Ester Electrolytes for Low-Temperature Li+ Cells; Miniature Free-Space Electrostatic Ion Thrusters; Miniature Bipolar Electrostatic Ion Thruster; Holographic Plossl Retroreflectors; Miniature Electrostatic Ion Thruster With Magnet; Using Apex To Construct CPM-GOMS Models; Sequence Detection for PPM Optical Communication With ISI; Algorithm for Rapid Searching Among Star-Catalog Entries; Expectation-Based Control of Noise and Chaos; Radio Heating of Lunar Soil to Release Gases; Using Electrostriction to Manipulate Ullage in Microgravity; Equations for Scoring Rules When Data Are Missing; Insulating Material for Next-Generation Spacecraft; and Pseudorandom Switching for Adding Radar to the AFF Sensor.

Source record↗

NASA NTRS2000

Terrestrial Applications of Zero Boil-Off Cryogen Storage

Storing cryogenic propellants with zero boil off (ZBO) using a combination of active (cryocoolers) and passive technologies has recently received a great deal of attention for applications such as future long-term space missions. This paper will examine a variety of potential near-term terrestrial applications for ZBO and, where appropriate, provide a rough order of magnitude cost benefit of implementing ZBO technology. NASA's Space Shuttle power system uses supercritical propellant tanks, which are filled several days before launch. If the launch does not occur within 48-96 hours, the tanks must be drained and refilled, further delaying the launch. By implementing ZBO, boil off could be eliminated and pad hold time extended. At the launch site, vented liquid hydrogen (LH2) storage dewars lose 1200-1600 gal/day through boiloff. Implementing ZBO would eliminate this, saving $300,000-$400,000 per year. Similarly, overland trucking of LH2 from the supplier to the launch site via roadable dewars results in a cryogen loss of ten percent per tanker (1500 gal/tanker). Providing a cryocooler on board the rig would prevent this loss. Previous work investigating variable density insulation found that a 50% reduction in evaporation from a 6000 gallon dewar would save $5000 per year. For a 20 year dewar lifetime, the payback period would be less than two years. Similar benefits could be realized at other storage facilities across the nation. Within the superconductivity community, there is skepticism about using coolers, based upon reliability concerns. By providing a cooler on the dewar, lifetime could be extended while retaining fail-safe capability. If the cooler failed, it would merely lower the storage life of the dewar.

Salerno, L. J.↗

NASA NTRS2005

NARC Rayon Replacement Program for the RSRM Nozzle, Phase IV Qualification and Implementation Status

The Space Shuttle NARC Rayon Replacement Program has down-selected Enka rayon as a replacement for the obsolete NARC rayon in the nozzle carbon cloth phenolic (CCP) ablative insulators. Full qualification testing of the Enka rayon-based carbon cloth phenolic is underway, including processing, thmal/structural properties, and hot-fire subscale tests. Required thermal-structural capabilities, together with confidence in erosio/char performance in simulated and subscale hot fire tests such as Wright-Patterson Air Force Base Laser Hardened Materials Evaluation Laboratory testing, NASA-MSFC 24-inch motor tests, NASA-MSFC Solid Fuel Torch - Super Sonic Blast Tube, NASA-MSFC Plasma Torch Test Bed, ATK Thiokol Forty Pound Charge and NASA-MSFC MNASA justified the testing of the new Enka-rayon candidate on full-scale static test motors. The first RSRM full-scale static test motor nozzle, fabricated using the new Enka rayon-based CCP, was successfully demonstrated in June 2004. Two additional static test motors are planned with the new Enka rayon in the next two years along with additional A-basis property characterization. Process variation or "corner-of-the-box" testing together with cured and uncured aging studies are also planned as some of the pre-flight implementation activities with 5-year cured aging studies over-lapping flight hardware fabrication.

Haddock, M. Reed↗