Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “WORK FUNCTIONS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17

Elucidating the Influence of Residual Polymer and Gas Environment on the Electronic Structure of a Graphene Layer Using in Situ APXPS

We use in situ ambient pressure X-ray photoelectron spectroscopy (APXPS) and ultraviolet photoelectron spectroscopy (UPS) to develop an effective method for studying changes in the graphene (Gr) electronic structure according to certain circumstance. The amount of polymethyl methacrylate (PMMA) residual polymer (RP), inevitably generated during the Gr transfer process, is significantly reduced from Gr surface by thermal annealing. This processed Gr is then sequentially exposed to specific gas environments (Ar, N 2 , O 2 , and CO 2 ), and APXPS or UPS is carried out to investigate the variations in the Gr electronic structure including the work function. When the amount of PMMA RP on Gr is reduced, the position of the main carbon peak shifts by more than 0.4 eV to a higher binding energy (in XPS spectra), and the secondary electron cutoff moves by about 0.2 eV to a lower binding energy (in UPS spectra). These changes are generally caused by a decrease in the Gr work function. On the other hand, exposure to the gas environments at different temperatures that we investigated did not produce significant changes in the work function and chemical states of Gr. These results confirm that the material in contact with Gr should be considered to achieve the desired Gr performance in electronics.

36 MATERIALS SCIENCE↗

Transmission Electron Microscopy and Electron Energy-Loss Spectroscopy Studies of Hole-Selective Molybdenum Oxide Contacts in Silicon Solar Cells

In this study, substochiometric hole-selective molybdenum oxide (MoO x ) contacts in crystalline silicon (c-Si) solar cells were investigated by a combination of transmission electron microscopy (TEM) and spatially resolved electron energy-loss spectroscopy (SR-EELS). It was observed that a ≈ 4 nm SiO x interlayer grows at the MoO x /c-Si interface during the evaporation of MoO x over a c-Si substrate. SR-EELS analyses revealed the presence of a 1.5 nm diffused MoO x /indium tin oxide (ITO) interface in both as-deposited and annealed samples. Moreover, the presence of a 1 nm thin layer with a lower oxidation state of Mo was detected at the SiO x /MoO x interface in an as-deposited state, which disappears upon annealing. Altogether, it was evident that no hole-blocking interlayer is formed at the MoO x /ITO interface during annealing and homogenization of the MoO x layer takes place during the annealing process. Furthermore, device simulations revealed that efficient hole collection is dependent on MoO x work function and that reduction in the work function of MoO x results in loss of band bending and negatively impacts hole selectivity.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Studies of thermionic materials for space power applications

The effect of microstructures of tungsten cladding on the transport rates of carbide fuel components was studied at 2073 K. hyperstoichiometric 90UC-10ZrC containing 4 wt% tungsten was clad with six types of tungsten material of 40 mil thickness. Screening tests of 1000 hours were carried out, and then selected samples were subjected to long-term tests up to 10,000 hours. The results indicate that the microstructures strongly affect the transport rates of carbide fuel components. The conditions for preparing (110) oriented cylindrical chloride tungsten emitters of high vacuum work functions were also investigated. Specimen sets were deposited on fluoride tungsten substrates for evaluating the effects of various deposition parameters on the degree and uniformity of the (110) preferred orientation and the vacuum work function. Long-term tests showed that the high vacuum work function of a cylindrical emitter was stable and the chloride tungsten to fluoride tungsten bond remained in excellent shape after 4850 hours at 2073 K.

Source record↗

Tuning of electronic properties of fullerene-oligothiophene layers

Electronic properties of fullerene derivatives containing oligothiophene pendant chain (1–3 thiophene moieties) were investigated using the Kelvin probe technique and quantum chemistry methods. For electrochemical examination of these systems, Langmuir–Blodgett (LB) layers were prepared by the deposition on a gold substrate. The analysis of the experimental data shows that the value of the work function depends strongly on the length of oligothiophene chain. Similar dependence was also found for the surface photovoltage measurements conducted for the layers consisting of multiple LB films of the examined compounds deposited on gold surfaces. The assumption has been made that these changes are associated with the influence of oligothiophene chain on the electrostatic potential distribution near the surface of the sample. The hypothesis was confirmed by the results of DFT calculations, which revealed that the value of Fermi level energy shifts in the opposite direction to the determined work function. The key highlights of this study are as follows: electronic structure tuning by oligothiophene side chain; DFT calculation on fullerene-thiophene system; work function measurements of thin molecular layers.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Kelvin probe force microscopy for high-resolution imaging of hydrogen in steel alloys [Poster]

Kelvin probe force microscopy (KPFM) was used to image and co-locate the presence of hydrogen in stainless steel (SS) with microstructure. Various SS samples were investigated, including forged, welded, LENS® fabricated, and pinch welded materials. KPFM images the local work function of a surface as a function of spatial position using atomic force microscopy. KPFM is capable of delivering high spatial (~10 nm) and potential (~5mV) resolution maps characterizing the microstrucure and the locally varying work function of surfaces. Hydrogen segregated at the surface of SS increases the local work function by either reducing tensile strain or by reducing the chemical potential of surface species. In a process known as hydrogen embrittlement, hydrogen segregates to and becomes trapped at extended defects (e.g. dislocations, boundaries, pores) which leads to the initiation of cracking and can result in structural failure. Hydrogen storage necessitates a proper understanding of the mechanisms of hydrogen embrittlement in SS. Developing advanced characterization techniques for hydrogen embrittlement is critical to identify long term solutions for materials exposed to hydrogen. Current techniques of observing hydrogen embrittlement involve mechanical testing, and optical microscopy with low resolution. Advance microstructural imaging techniques capable of resolving features down to the nanometer scale are needed. KPFM provides high resolution imaging for the characterization and development of SS components for hydrogen storage.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Modeling the flux of high energy negative ions during reactive magnetron sputtering

The negative ion flux during reactive sputtering from planar and rotating cylindrical magnetrons has been studied. Energy resolved mass spectrometry was used to measure the energy and mass distribution of the negative ions. Also the angular distribution of the high energy ions was characterized for planar as well as for rotating cylindrical magnetrons. Besides these measurements, a binary collision Monte Carlo simulation code, SiMTRA, was adapted in order to simulate the energy, mass, and angular distribution of the high energy negative ions. All simulated distributions, for both planar and rotating cylindrical magnetrons, were in excellent correspondence with the experimental observations. Also a model for the amount of high energy negative O{sup -} ions was proposed. Indeed, the logarithm of the amount of high energy negative O{sup -} ions is shown to be related to the secondary electron emission yield of the oxide target, and these two parameters are known to be related to the work function. The SiMTRA simulations, in combination with knowledge of the work function or secondary electron emission yield of the target, allow modeling the flux of high energy negative ions during reactive magnetron sputtering.

36 MATERIALS SCIENCE↗

Adsorption Structures and Electronic Properties of 1,4-Phenylene Diisocyanide on the Au(111) Surface

The adsorption structures and electronic properties of 1,4-phenylene diisocyanide (PDI) on a Au(111) surface have been studied using temperature programmed desorption (TPD), two-photon photoemission (2PPE), and scanning tunneling microscopy (STM). As deposited at 95 K, PDI molecules form disordered islands and short one-dimensional chains on Au(111) terraces. The work function decreases with increasing PDI coverage, and an occupied electronic state appears at 0.88 eV below the Fermi level. Annealing to 300 K causes the PDI molecules to reorganize on the surface and form ordered, one-dimensional molecular chains that extend for many tens of nanometers across the Au(111) terraces. The repeating structure of the molecular chains is consistent with a recently proposed [-Au-PDI-]{sub n} structure in which PDI molecules lie parallel to the surface and are interconnected by Au adatoms released from the Au(111) surface. The formation of the molecular chains is accompanied by a large drop in the work function which we attribute to an increase in the number and magnitude of interfacial dipoles. The electronic structure of the molecular chains is also characterized by occupied and unoccupied states at -0.88 eV below and +3.32 eV above the Fermi level, respectively. The latter are most prominent after annealing a PDI/Au(111) surface to 300 K, indicating that they are associated with interfacial states of the one-dimensional molecular chains.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Back-gated graphene anode for more efficient thermionic energy converters

Thermionic energy converters (TECs) are a direct heat-to-electricity conversion technology with great potential for high efficiency and scalability. However, space charge barrier in the inter-electrode gap and high anode work function are major obstacles toward realizing high efficiency. Here, we demonstrate for the first time a prototype TEC using a back-gated graphene anode, a barium dispenser cathode, and a controllable inter-electrode gap as small as 17 µm, which simultaneously addresses these two obstacles. This leads to an electronic conversion efficiency of 9.8% at cathode temperature of 1000 °C, the highest reported by far. We first demonstrate that electrostatic gating of graphene by a 20 nm HfO 2 dielectric layer changes the graphene anode work function by 0.63 eV, as observed from the current-voltage characteristics of the TEC. Next, we show that the efficiency increases by a factor of 30.6 by reducing the gap from 1 mm down to 17 µm, after a mono-layer of Ba is deposited on graphene by the dispenser cathode. Lastlu, we show that electrostatic gating of graphene further reduces the graphene work function from 1.85 to 1.69 eV, leading to an additional 67% enhancement in TEC efficiency. Note that the overall efficiency using the back-gated graphene anode is 6.7 times higher compared with that of a TEC with a tungsten anode and the same inter-electrode gap.

30 DIRECT ENERGY CONVERSION↗

Comment on “Tunneling-tip-induced collapse of the charge gap in the excitonic insulator Ta 2 NiSe 5 ”

In this study, we investigate the discrepancy between the estimate of Q. He [], who observed a remarkable collapse of the exciton gap in Ta 2 NiSe 5 due to the electrostatic field between the scanning tunneling microscope (STM) tip and the sample, and that of a recent angle-resolved photoemission spectroscopy investigation [C. Chen , ]. It is proposed that a critical factor contributing to this discrepancy is due to He 's assumption of a constant work function of the STM tip. This assumption led to an underestimation of the tip-induced electric field. Using a literature value for the sample work function, a more substantial electric field strength is obtained, which resolves the apparent conflict between the doping estimates of these two techniques. Furthermore, our findings highlight the importance of the STM tip condition, which can significantly impact the tip work function and, consequently, influence the doping estimation in experiments involving tip-induced electric fields. Published by the American Physical Society 2024

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Feasibility study of oxygen-dispensing emitters for thermionic converters, phase 1

A metal/ceramic Marchuk tube was used to measure work functions of oxygen-doped tantalum, to determine applicability of the material to plasma-mode thermionic converters. Oxygen-doped tantalum was shown to increase in work function monotonically with oxygen doping in the range 0.1 to 0.3 atomic percent. Oxygenated test emitters were run at an average temperature of 2165 K and a T/T sub Cs ratio -5.8 to observe the influence of oxygen depletion. Bare work function decreased with outgassing of oxygen. Projections were made based on outgassing kinetics and area/volume ratios to calculate the longevity of oxygen doping in a practical converter. Calculations indicated that the program goal of 10,000 hr could be achieved at 1800 K with an initial oxygen doping of 1 atomic percent and a practical emitter area/volume ratio.

Desteese, J. G.↗

Surface studies of barium and barium oxide on tungsten and its application to understanding the mechanism of operation of an impregnated tungsten cathode

Surface studies have been made of multilayer and monolayer films of barium and barium oxide on a tungsten substrate. The purpose of the investigation was to synthesize the surface conditions that exist on an activated impregnated tungsten cathode and obtain a better understanding of the mechanism of operation of such cathodes. The techniques employed in these measurements were Auger spectroscopy and work-function measurements. The results of this study show that the surface of an impregnated cathode is identical to that observed for a synthesized monolayer or partial monolayer of barium on oxidized tungsten by evaluating Auger spectra and work-function measurements. Data obtained from desorption studies of barium monolayers on a tungsten substrate in conjunction with Auger and work-function results have been interpreted to show that throughout most of its life an impreganated cathode has a partial monolayer, rather than a monolayer, of barium on its surface.

Forman, R.↗

Schottky contact formation on polar and non-polar AlN

The interfaces of m- and c-plane AlN with metals of different work functions and electro-negativities were characterized and the Schottky barrier heights were measured. The Schottky barrier height was determined by measuring the valence band maximum (VBM) with respect to the Fermi level at the surface (interface) before (after) metallization. VBM determination included accurate modeling and curve fitting of density of states at the valence band edge with the XPS data. The experimental behavior of the barrier heights could not be explained by the Schottky-Mott model and was modeled using InterFace-Induced Gap States (IFIGS). A slope parameter (S{sub X}) was used to incorporate the density of surface states and is a measure of Fermi level pinning. The experimental barriers followed theoretical predictions with a barrier height at the surface Fermi level (Charge neutrality level (CNL)) of ∼2.1 eV (∼2.7 eV) on m-plane (c-plane) and S{sub X} ∼ 0.36 eV/Miedema unit. Slope parameter much lower than 0.86 implied a surface/interface states dominated behavior with significant Fermi level pinning and the measured barrier heights were close to the CNL. Titanium and zirconium provided the lowest barriers (1.6 eV) with gold providing the highest (2.3 eV) among the metals analyzed on m-plane. It was consistently found that barrier heights decreased from metal polar to non-polar surfaces, in general, due to an increasing CNL. The data indicated that charged IFIGS compensate spontaneous polarization charge. These barrier height and slope parameter measurements provided essential information for designing Schottky diodes and other contact-based devices on AlN.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Thermionic Properties of Carbon Based Nanomaterials Produced by Microhollow Cathode PECVD

Thermionic emission is the process in which materials at sufficiently high temperature spontaneously emit electrons. This process occurs when electrons in a material gain sufficient thermal energy from heating to overcome the material's potential barrier, referred to as the work function. For most bulk materials very high temperatures (greater than 1500 K) are needed to produce appreciable emission. Carbon‐based nanomaterials have shown significant promise as emission materials because of their low work functions, nanoscale geometry, and negative electron affinity. One method of producing these materials is through the process known as microhollow cathode PECVD. In a microhollow cathode plasma, high energy electrons oscillate at very high energies through the Pendel effect. These high energy electrons create numerous radical species and the technique has been shown to be an effective method of growing carbon based nanomaterials. In this work, we explore the thermionic emission properties of carbon based nanomaterials produced by microhollow cathode PECVD under a variety of synthesis conditions. Initial studies demonstrate measureable current at low temperatures (approximately 800 K) and work functions (approximately 3.3 eV) for these materials.

Haase, John R.↗

Characterization of metal contacts for two-dimensional MoS{sub 2} nanoflakes

While layered materials are increasingly investigated for their potential in nanoelectronics, their functionality and efficiency depend on charge injection into the materials via metallic contacts. This work explores the characteristics of different metals (aluminium, tungsten, gold, and platinum) deposited on to nanostructured thin films made of two-dimensional (2D) MoS{sub 2} flakes. Metals are chosen based on their work functions relative to the electron affinity of MoS{sub 2}. It is observed, and analytically verified that lower work functions of the contact metals lead to smaller Schottky barrier heights and consequently higher charge carrier injection through the contacts.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Methodology to Support Dynamic Function Allocation Policies Between Humans and Flight Deck Automation

Function allocation assigns work functions to all agents in a team, both human and automation. Efforts to guide function allocation systematically have been studied in many fields such as engineering, human factors, team and organization design, management science, cognitive systems engineering. Each field focuses on certain aspects of function allocation, but not all; thus, an independent discussion of each does not address all necessary aspects of function allocation. Four distinctive perspectives have emerged from this comprehensive review of literature on those fields: the technology-centered, human-centered, team-oriented, and work-oriented perspectives. Each perspective focuses on different aspects of function allocation: capabilities and characteristics of agents (automation or human), structure and strategy of a team, and work structure and environment. This report offers eight issues with function allocation that can be used to assess the extent to which each of issues exist on a given function allocation. A modeling framework using formal models and simulation was developed to model work as described by the environment, agents, their inherent dynamics, and relationships among them. Finally, to validate the framework and metrics, a case study modeled four different function allocations between a pilot and flight deck automation during the arrival and approach phases of flight.

Johnson, Eric N.↗

Fabrication and surface characterization of composite refractory compounds suitable for thermionic converters

Procedures for fabricating high purity single crystals of LaB6 and SmB6 have been developed. Auger spectroscopy shows that a clean surface can be obtained by thermal heating at 1700 K; such a clean surface gives a value of B/La of 2.3 to 2.6 for the (100) face. The measured thermionic and FERP work functions of the (100) face of LaB6 are 2.47 and 2.28 eV, respectively. The electron reflection coefficient for LaB6(100) increases near zero primary energy to 0.5. Flash thermal desorption of an oxygen dosed surface showed that B2O3 is the desorption product at 1600 to 1700 K. A work function increase of 1.6 eV was observed on oxygen adsorption on LaB6(100). Thermal desorption of Co occurs at approximately 1300 K. A reduction of the work function to 1.39 eV was observed on adsorption of a partial monolayer of Cs on LaB6(100). The evaporation of LaB6 occurs as atomic La and B with a value of B/La of 6 to 3 in the temperature range 1700 to 2000 K. The activation energies of desorption for La and B are 6.3 + or - 0.3 and 6.8 + or - 0.3 eV, respectively.

Swanson, L. W.↗

Surface studies of thermionic cathodes and the mechanism of operation of an impregnated tungsten cathode

The surface properties of conventional impregnated cathodes were investigated by the use of Auger spectroscopy and work function measurements, and these were compared with a synthesized barium or barium oxide coated tungsten surface. The barium and barium oxide coated surfaces were prepared by evaporating barium onto a tungsten surface that can be heated to elevated temperatures. Multilayer or monolayer coverages can be investigated using this technique. The results of this study show that the surface of an impregnated tungsten cathode is identical to that observed for a synthesized monolayer or partial monolayer of barium on partially oxidized tungsten, using the criteria of identical Auger patterns and work functions. Desorption measurements of barium from a tungsten surface were also made. These results in conjunction with Auger and work function data were interpreted to show that throughout most of its life an impregnated cathode operating in the range of 1100 C has a partial monolayer rather than a monolayer of barium on its surface.

Forman, R.↗

Detailed Studies of Pixelated CZT Detectors Grown with the Modified Horizontal Bridgman Method

The detector material Cadmium Zinc Telluride (CZT) achieves excellent spatial resolution and good energy resolution over a broad energy range, several keV up to some MeV. Presently, there are two main methods to grow CZT crystals, the Modified High-Pressure Bridgman (MHB) and the High-Pressure Bridgman (HPB) process. The study presented in this paper is based on MHB CZT substrates from the company Orbotech Medical Solutions Ltd. [Orbotech Medical Solutions Ltd., 10 Plaut St., Park Rabin, P.O. Box 2489, Rehovot, Israel, 76124]. Former studies have shown that high-work-function materials on the cathode side reduce the leakage current and, therefore, improve the energy resolution at lower energies. None of the studies have emphasized on the anode contact material. Therefore, we present in this paper the result of a detailed study in which for the first time the cathode material was kept constant and the anode material was varied. We used four different anode materials: Indium, Titanium, Chromium and Gold, metals with work-functions between 4.1 eV and 5.1 eV. The detector size was 2.0 x 2.0 x 0.5 cu cm with 8 x 8 pixels and a pitch of 2.46 mm. The best performance was achieved with the low-work-function materials Indium and Titanium with energy resolutions of 2.0 keV (at 59 keV) and 1.9 keV (at 122 keV) for Titanium and 2.1 keV (at 59 keV) and 2.9 keV (at 122 keV) for Indium. Taking into account the large pixel pitch of 2.46 mm, these resolutions are very competitive in comparison to those achieved with detectors made of material produced with the more expensive conventional HPB method. We present a detailed comparison of our detector response with 3D simulations. The latter comparisons allow us to determine the mobility-lifetime-products (mu tau-products) for electrons and holes. Finally, we evaluated the temperature dependency of the detector performance and ls-products. For many applications temperature dependence is important, therefore, we extended the scope of our study to temperatures as low as -30 C. There are two important results. The breakdown voltage increases with decreasing temperature, and electron mobility-lifetime-product decreases by about 30% over a range from 20 C to -30 C. The latter effect causes the energy resolution to deteriorate, but the concomitantly increasing breakdown voltage makes it possible to increase the applied bias voltage and restore the full performance

Jung, I.↗