Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “WORK FUNCTION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17

Feasibility study of oxygen-dispensing emitters for thermionic converters, phase 1

A metal/ceramic Marchuk tube was used to measure work functions of oxygen-doped tantalum, to determine applicability of the material to plasma-mode thermionic converters. Oxygen-doped tantalum was shown to increase in work function monotonically with oxygen doping in the range 0.1 to 0.3 atomic percent. Oxygenated test emitters were run at an average temperature of 2165 K and a T/T sub Cs ratio -5.8 to observe the influence of oxygen depletion. Bare work function decreased with outgassing of oxygen. Projections were made based on outgassing kinetics and area/volume ratios to calculate the longevity of oxygen doping in a practical converter. Calculations indicated that the program goal of 10,000 hr could be achieved at 1800 K with an initial oxygen doping of 1 atomic percent and a practical emitter area/volume ratio.

Desteese, J. G.↗

Surface studies of barium and barium oxide on tungsten and its application to understanding the mechanism of operation of an impregnated tungsten cathode

Surface studies have been made of multilayer and monolayer films of barium and barium oxide on a tungsten substrate. The purpose of the investigation was to synthesize the surface conditions that exist on an activated impregnated tungsten cathode and obtain a better understanding of the mechanism of operation of such cathodes. The techniques employed in these measurements were Auger spectroscopy and work-function measurements. The results of this study show that the surface of an impregnated cathode is identical to that observed for a synthesized monolayer or partial monolayer of barium on oxidized tungsten by evaluating Auger spectra and work-function measurements. Data obtained from desorption studies of barium monolayers on a tungsten substrate in conjunction with Auger and work-function results have been interpreted to show that throughout most of its life an impreganated cathode has a partial monolayer, rather than a monolayer, of barium on its surface.

Forman, R.↗

Schottky contact formation on polar and non-polar AlN

The interfaces of m- and c-plane AlN with metals of different work functions and electro-negativities were characterized and the Schottky barrier heights were measured. The Schottky barrier height was determined by measuring the valence band maximum (VBM) with respect to the Fermi level at the surface (interface) before (after) metallization. VBM determination included accurate modeling and curve fitting of density of states at the valence band edge with the XPS data. The experimental behavior of the barrier heights could not be explained by the Schottky-Mott model and was modeled using InterFace-Induced Gap States (IFIGS). A slope parameter (S{sub X}) was used to incorporate the density of surface states and is a measure of Fermi level pinning. The experimental barriers followed theoretical predictions with a barrier height at the surface Fermi level (Charge neutrality level (CNL)) of ∼2.1 eV (∼2.7 eV) on m-plane (c-plane) and S{sub X} ∼ 0.36 eV/Miedema unit. Slope parameter much lower than 0.86 implied a surface/interface states dominated behavior with significant Fermi level pinning and the measured barrier heights were close to the CNL. Titanium and zirconium provided the lowest barriers (1.6 eV) with gold providing the highest (2.3 eV) among the metals analyzed on m-plane. It was consistently found that barrier heights decreased from metal polar to non-polar surfaces, in general, due to an increasing CNL. The data indicated that charged IFIGS compensate spontaneous polarization charge. These barrier height and slope parameter measurements provided essential information for designing Schottky diodes and other contact-based devices on AlN.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Thermionic Properties of Carbon Based Nanomaterials Produced by Microhollow Cathode PECVD

Thermionic emission is the process in which materials at sufficiently high temperature spontaneously emit electrons. This process occurs when electrons in a material gain sufficient thermal energy from heating to overcome the material's potential barrier, referred to as the work function. For most bulk materials very high temperatures (greater than 1500 K) are needed to produce appreciable emission. Carbon‐based nanomaterials have shown significant promise as emission materials because of their low work functions, nanoscale geometry, and negative electron affinity. One method of producing these materials is through the process known as microhollow cathode PECVD. In a microhollow cathode plasma, high energy electrons oscillate at very high energies through the Pendel effect. These high energy electrons create numerous radical species and the technique has been shown to be an effective method of growing carbon based nanomaterials. In this work, we explore the thermionic emission properties of carbon based nanomaterials produced by microhollow cathode PECVD under a variety of synthesis conditions. Initial studies demonstrate measureable current at low temperatures (approximately 800 K) and work functions (approximately 3.3 eV) for these materials.

Haase, John R.↗

Characterization of metal contacts for two-dimensional MoS{sub 2} nanoflakes

While layered materials are increasingly investigated for their potential in nanoelectronics, their functionality and efficiency depend on charge injection into the materials via metallic contacts. This work explores the characteristics of different metals (aluminium, tungsten, gold, and platinum) deposited on to nanostructured thin films made of two-dimensional (2D) MoS{sub 2} flakes. Metals are chosen based on their work functions relative to the electron affinity of MoS{sub 2}. It is observed, and analytically verified that lower work functions of the contact metals lead to smaller Schottky barrier heights and consequently higher charge carrier injection through the contacts.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Methodology to Support Dynamic Function Allocation Policies Between Humans and Flight Deck Automation

Function allocation assigns work functions to all agents in a team, both human and automation. Efforts to guide function allocation systematically have been studied in many fields such as engineering, human factors, team and organization design, management science, cognitive systems engineering. Each field focuses on certain aspects of function allocation, but not all; thus, an independent discussion of each does not address all necessary aspects of function allocation. Four distinctive perspectives have emerged from this comprehensive review of literature on those fields: the technology-centered, human-centered, team-oriented, and work-oriented perspectives. Each perspective focuses on different aspects of function allocation: capabilities and characteristics of agents (automation or human), structure and strategy of a team, and work structure and environment. This report offers eight issues with function allocation that can be used to assess the extent to which each of issues exist on a given function allocation. A modeling framework using formal models and simulation was developed to model work as described by the environment, agents, their inherent dynamics, and relationships among them. Finally, to validate the framework and metrics, a case study modeled four different function allocations between a pilot and flight deck automation during the arrival and approach phases of flight.

Johnson, Eric N.↗

Fabrication and surface characterization of composite refractory compounds suitable for thermionic converters

Procedures for fabricating high purity single crystals of LaB6 and SmB6 have been developed. Auger spectroscopy shows that a clean surface can be obtained by thermal heating at 1700 K; such a clean surface gives a value of B/La of 2.3 to 2.6 for the (100) face. The measured thermionic and FERP work functions of the (100) face of LaB6 are 2.47 and 2.28 eV, respectively. The electron reflection coefficient for LaB6(100) increases near zero primary energy to 0.5. Flash thermal desorption of an oxygen dosed surface showed that B2O3 is the desorption product at 1600 to 1700 K. A work function increase of 1.6 eV was observed on oxygen adsorption on LaB6(100). Thermal desorption of Co occurs at approximately 1300 K. A reduction of the work function to 1.39 eV was observed on adsorption of a partial monolayer of Cs on LaB6(100). The evaporation of LaB6 occurs as atomic La and B with a value of B/La of 6 to 3 in the temperature range 1700 to 2000 K. The activation energies of desorption for La and B are 6.3 + or - 0.3 and 6.8 + or - 0.3 eV, respectively.

Swanson, L. W.↗

Surface studies of thermionic cathodes and the mechanism of operation of an impregnated tungsten cathode

The surface properties of conventional impregnated cathodes were investigated by the use of Auger spectroscopy and work function measurements, and these were compared with a synthesized barium or barium oxide coated tungsten surface. The barium and barium oxide coated surfaces were prepared by evaporating barium onto a tungsten surface that can be heated to elevated temperatures. Multilayer or monolayer coverages can be investigated using this technique. The results of this study show that the surface of an impregnated tungsten cathode is identical to that observed for a synthesized monolayer or partial monolayer of barium on partially oxidized tungsten, using the criteria of identical Auger patterns and work functions. Desorption measurements of barium from a tungsten surface were also made. These results in conjunction with Auger and work function data were interpreted to show that throughout most of its life an impregnated cathode operating in the range of 1100 C has a partial monolayer rather than a monolayer of barium on its surface.

Forman, R.↗

Detailed Studies of Pixelated CZT Detectors Grown with the Modified Horizontal Bridgman Method

The detector material Cadmium Zinc Telluride (CZT) achieves excellent spatial resolution and good energy resolution over a broad energy range, several keV up to some MeV. Presently, there are two main methods to grow CZT crystals, the Modified High-Pressure Bridgman (MHB) and the High-Pressure Bridgman (HPB) process. The study presented in this paper is based on MHB CZT substrates from the company Orbotech Medical Solutions Ltd. [Orbotech Medical Solutions Ltd., 10 Plaut St., Park Rabin, P.O. Box 2489, Rehovot, Israel, 76124]. Former studies have shown that high-work-function materials on the cathode side reduce the leakage current and, therefore, improve the energy resolution at lower energies. None of the studies have emphasized on the anode contact material. Therefore, we present in this paper the result of a detailed study in which for the first time the cathode material was kept constant and the anode material was varied. We used four different anode materials: Indium, Titanium, Chromium and Gold, metals with work-functions between 4.1 eV and 5.1 eV. The detector size was 2.0 x 2.0 x 0.5 cu cm with 8 x 8 pixels and a pitch of 2.46 mm. The best performance was achieved with the low-work-function materials Indium and Titanium with energy resolutions of 2.0 keV (at 59 keV) and 1.9 keV (at 122 keV) for Titanium and 2.1 keV (at 59 keV) and 2.9 keV (at 122 keV) for Indium. Taking into account the large pixel pitch of 2.46 mm, these resolutions are very competitive in comparison to those achieved with detectors made of material produced with the more expensive conventional HPB method. We present a detailed comparison of our detector response with 3D simulations. The latter comparisons allow us to determine the mobility-lifetime-products (mu tau-products) for electrons and holes. Finally, we evaluated the temperature dependency of the detector performance and ls-products. For many applications temperature dependence is important, therefore, we extended the scope of our study to temperatures as low as -30 C. There are two important results. The breakdown voltage increases with decreasing temperature, and electron mobility-lifetime-product decreases by about 30% over a range from 20 C to -30 C. The latter effect causes the energy resolution to deteriorate, but the concomitantly increasing breakdown voltage makes it possible to increase the applied bias voltage and restore the full performance

Jung, I.↗

Thermionic converter performance with oxide collectors

Thermionic converters using a variety of metal oxide collector surfaces have been fabricated and tested. Both work function and power output data are presented and evaluated. Oxides of barium, strontium, zinc, tungsten and titanium have been incorporated into a variable spacing converter. Tungsten oxide was found to give the highest converter performance and to furnish oxygen for the emitter at the same time. Oxygenated emitters operate at reduced cesium pressure with an increase in electrode spacing. Electron spectroscopy for chemical analysis (ESCA) performed on several tungsten oxide collectors showed cesium penetration of the oxide layer, possibly forming a cesium tungstate bronze. Titanium oxide showed high performance but did not furnish oxygen for the emitter; strontium oxide, in the form of a sprayed layer, appeared to dissociate in the presence of cesium. Sprayed coatings of barium and zinc oxides produced collector work functions of about 1.3 eV, but had excessive series resistance. Lanthanum hexaboride, in combination with oxygen introduced through a silver tube, and cesium produced a low work function collector and better than average performance.

Lieb, D.↗

On the charge neutrality level and the electronic properties of interphase boundaries in the layered ε-GaSe semiconductor

The height of the (Au, Pd, Pt, Cu, Ag, Sn, In, Al, Mg, Ca, Li, Cs)/GaSe(0001) Schottky barrier as a function of the metal work function and the energy-band offsets in InSe(0001)/GaSe(0001) and GaSe(0001)/Si(111) heteropairs are analyzed within the context of the concept of the charge neutrality level, CNL{sub vb}(GaSe) = E{sub v} + 0.83 eV, with consideration for partial screening of the interface electrostatic dipole by metal- or semiconductor-induced tunneling states at the GaSe(0001) surface.

36 MATERIALS SCIENCE↗

Out-of-core evaluations of a nonfueled and a UO2-fueled cylindrical thermionic converter.

Two cylindrical thermionic energy converters similar to those in a flashlight thermionic fuel element were tested electrically at the Jet Propulsion Laboratory. One converter was not fueled, but the other was fueled with UO2 imbedded in six pencil-lead-size holes in the emitter, which was made of rhenium. The nonfueled converters showed no change in its performance during 4000 hr of testing, whereas the output current of the UO2-fueled converter degraded 15% during 2400 hr of testing at 2000 K. Measurements on the UO2-fueled converter showed an increase in the collector work function and an increase in the bare emitter work function. The degradation appears to be caused primarily by foreign deposits on the collector, probably uranium that diffused from the UO2 fuel through the emitter.

Shimada, K.↗

Spacecraft surface charging as a function of material properties

Spacecraft material behavior plays a very important role in space missions. Spacecraft immersed in plasma get charged by absorbing plasma particles and by emitting electrons from spacecraft surfaces via photoelectron and secondary electron emission. Spacecraft charging depends heavily on material properties such as work function, secondary electron yield, dielectric constant, and electric conductivity among other. Material properties are typically assumed to be static in charging models. However, it is well known that this is not the case in space. This makes spacecraft charging predictions very challenging. Material properties are well characterized before the spacecraft is put in orbit through characterization in the lab under clean conditions. However, once in space, material properties change due to the harsh and very dynamic space environment. We present a new capability to predict material behavior in space from first-principles modeling. The ongoing effort seeks to couple material models, density functional theory (DFT) and molecular dynamic (MD) codes, with environment models, plasma kinetic codes. This preliminary study will show results of surface charging as a function of material work function, dielectric constant, and conductivity.

36 MATERIALS SCIENCE↗

HIGH-TEMPERATURE IONIZATION IN PROTOPLANETARY DISKS

We calculate the abundances of electrons and ions in the hot (≳500 K), dusty parts of protoplanetary disks, treating for the first time the effects of thermionic and ion emission from the dust grains. High-temperature ionization modeling has involved simply assuming that alkali elements such as potassium occur as gas-phase atoms and are collisionally ionized following the Saha equation. We show that the Saha equation often does not hold, because free charges are produced by thermionic and ion emission and destroyed when they stick to grain surfaces. This means the ionization state depends not on the first ionization potential of the alkali atoms, but rather on the grains’ work functions. The charged species’ abundances typically rise abruptly above about 800 K, with little qualitative dependence on the work function, gas density, or dust-to-gas mass ratio. Applying our results, we find that protoplanetary disks’ dead zone, where high diffusivities stifle magnetorotational turbulence, has its inner edge located where the temperature exceeds a threshold value ≈1000 K. The threshold is set by ambipolar diffusion except at the highest densities, where it is set by Ohmic resistivity. We find that the disk gas can be diffusively loaded onto the stellar magnetosphere at temperatures below a similar threshold. We investigate whether the “short-circuit” instability of current sheets can operate in disks and find that it cannot, or works only in a narrow range of conditions; it appears not to be the chondrule formation mechanism. We also suggest that thermionic emission is important for determining the rate of Ohmic heating in hot Jupiters.

79 ASTRONOMY AND ASTROPHYSICS↗

Adsorption dynamics and angular dependency of contaminants on Ru mirror surfaces

A real time contamination of the Ru surface and corresponding effect on its work function were studied using extreme ultraviolet photoelectron spectroscopy with a 13.5-nm wavelength of light. The change in work function indicates formation of molecular dipoles, oriented outward from the Ru surface. X-ray photoelectron spectroscopy investigations suggest variation in electromagnetic interaction with the components of the adsorbed foreign species when the emission angle from the target surface was changed from 0 deg. to 50 deg. ; H{sub 2}O and C-O{sub n} show a strong coupling at lower angles and OH dominates at higher angles, whereas carbon is found in the mid-range peaking at 30 deg. .

36 MATERIALS SCIENCE↗

Operando study of Pd(100) surface during CO oxidation using ambient pressure x-ray photoemission spectroscopy

The surface chemical states of Pd(100) during CO oxidation were investigated using ambient pressure x-ray photoelectron spectroscopy and mass spectroscopy. Under the reactant ratio of CO/O 2 = 0.1, i.e. an oxygen-rich reaction condition, the formation of surface oxides was observed with the onset of CO oxidation reaction at T = 525 K. As the reactant ratio (CO/O 2 ) increased from 0.1 to 1.0, ~ 90 % surface oxides remains on surface during the reaction. Upon the formation of surface oxides, the core level shift of oxygen gas phase peak was observed, indicating that change of surface work function. As CO oxidation takes places, i.e. making a transition from CO covered surface to the oxidic surface, the work functions of surface oxide on Pd(100) and Pt(110) display opposite behavior.

36 MATERIALS SCIENCE↗

Field emission characteristics from graphene on hexagonal boron nitride

An attempt has been made to utilize uniquely high electron mobility of graphene on hexagonal boron nitride (h-BN) to electron emitter. The field emission property of graphene/h-BN/Si structure has shown enhanced threshold voltage and emission current, both of which are key to develop novel vacuum nanoelectronics devices. The field emission property was discussed along with the electronic structure of graphene investigated by Fowler-Nordheim plot and ultraviolet photoelectron spectroscopy. The result suggested that transferring graphene on h-BN modified its work function, which changed field emission mechanism. Our report opens up a possibility of graphene-based vacuum nanoelectronics devices with tuned work function.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

The physical properties of Li-doped g-C{sub 3}N{sub 4} monolayer sheet investigated by the first-principles

Highlights: • Systematically research on Li-doped g-C{sub 3}N{sub 4} monolayer sheets by first-principles calculation. • Optimal dopant concentration for optical absorption is 7.12%. • Thermodynamics stability of the doped substrate g-C{sub 3}N{sub 4} decreased with Li dopant concentration increasing. • The values of work function Φ decreased monotonously with the increasing of Li dopant concentration. - Abstract: The geometric, electronic, optical properties, thermodynamic stability, and work function of Li-doped g-C{sub 3}N{sub 4} monolayer were investigated by the first-principles calculation. It was found that the Li atoms were preferentially substituted the open-hollow sites of g-C{sub 3}N{sub 4}. Interestingly, the “odd” number of Li doped g-C{sub 3}N{sub 4} showed metallic properties, while the “even” number of Li atoms widened the band gap of g-C{sub 3}N{sub 4}. The HOMO and LUMO distributions reveal that the active sites located at edge N and C atoms for both pristine and the Li-doped g-C{sub 3}N{sub 4}. In addition, thermodynamic analysis showed that the doped Li atoms reduced the thermodynamic stability of g-C{sub 3}N{sub 4} monolayer sheets.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗