Results for “Simulation Quality” — Page 17

NASA NTRS1972

A flight evaluation of a vectored thrust jet V/STOL airplane during simulated instrument approaches using the Kestrel (XV-6A) airplane

An in-flight investigation was made to determine the terminal-area operating problems of a vectored-thrust-jet vertical and short take-off landing (V/STOL) airplane under simulated instrument conditions. Handling-qualities data pertinent to the terminal-area approach and landing task are presented in the text, and additional documentation is included in the appendixes. Problems dealing with the cruise letdown to localizer capture, conversion to powered-lift flight, precise control of the glide slope, approach velocity or deceleration schedule, hover, and landing are discussed.

Morello, S. A.↗

NASA NTRS1979

AXAF optical technology analysis

A grazing incidence telescope with six nested subsystems is investigated through the effects of misalignment and surface deformations on it's image quality. The axial rms-spot size serves as measure for the image quality. The surface deformations are simulated by ellipsoidal and sinusoidal deviation elements. Each type of defect is analyzed in the single two-element system. The full nested system is then analyzed in the presence of all possible defects on all twelve elements, whereby the magnitude of the defects is randomized within a given upper limit.

Korsch, D.↗

NASA NTRS1979

Influence of alignment and surface defects on the performance of X-ray telescopes

The effects of misalignment and surface deformations on the image quality of a grazing incidence telescope with six nested subsystems are investigated. The axial rms-spot size serves as a measure for the image quality. The surface deformations are simulated by ellipsoidal and sinusoidal deviations from the ideal surface. Misalignments are tilts, decenters, and despaces of the individual elements. The effects of each type of defect are analyzed in a single two-element system. The full nested system is then analyzed in the presence of all possible defects on all 12 elements, whereby the magnitude of the defects is randomized within a given upper limit.

Korsch, D.↗

NASA NTRS1982

Flight testing the Rotor Systems Research Aircraft (RSRA)

The Rotor Systems Research Aircraft (RSRA) is a dedicated rotor test vehicle whose function is to fill the gap between theory, wind tunnel tests and flight verification data. Its flight test envelope has been designed to encompass the expected envelopes of future rotor systems under all flight conditions. The test configurations of the RSRA include pure helicopter and compound (winged helicopter) modes. In addition, should it become necessary to jettison an unstable rotor system in flight, the RSRA may be flown as a fixed wing aircraft. The heart of the RSRA's electronic flight control system is the TDY-43 computer, which can be programmed in numerous ways to change stability and control or force feel system gains. Computer programming changes allow the RSRA to be used as a five-degree-of-freedom inflight simulator for studying the handling qualities of research rotors.

Merrill, R. K.↗

NASA NTRS1984

Sensitivity analysis of high-efficiency silicon solar-cell design parameters

Silicon solar cell design parameters were investigated to determine their bearing on cell efficiency. Among the parameters reviewed were: (1) bulk resistivity, (2) minority carrier lifetime cell thickness, (3) front junction depth, (4) front surface doping concentration, (5) front surface recombination velocity, and (6) back surface contact. The following were concluded: (1) there is good agreement between experimental and simulation results; (2) sheet material quality improvement is needed for high efficiency cells; (3) 20% cell of this design is feasible with 10 ms bulk lifetime material; and (4) for achieving efficiencies higher than 20% new cell designs including thin cells with light trapping and back surface field should be considered.

Mokashi, A. R.↗

NASA NTRS1988

Cartesian path control of a two-degree-of-freedom robot manipulator

The problem of cartesian trajectory control of a closed-kinematic chain mechanism robot manipulator with possible space station applications is considered. The study was performed by both computer simulation and experimentation for tracking of three different paths: a straight line, a sinusoid and a circle. Linearization and pole placement methods are employed to design controller gains. Results show that the controllers are robust and there are good agreements between simulation and experimentation. Excellent tracking quality and small overshoots are also evident.

Nguyen, Charles C.↗

NASA NTRS1990

Operational considerations for aerodynamic testing of large-scale wing sections in a simulated natural rain environment

One of the necessary areas of consideration for outdoor heavy rain testing is the effect of wind on both the simulated rain field and the quality and repeatability of the aerodynamic data. This paper discusses the data acquisition and subsequent reduction to nondimensional coefficients of lift and drag, with the appropriate correction for wind and rain field. Sample force data showing these effects are presented, along with estimates for accuracy and repeatability. The capability to produce high-quality data for rain drop size distribution using photographic and computerized image processing techniques was developed. Sample photographs depicting rain drop size are shown.

Campbell, Bryan A.↗

NASA NTRS1993

Fuzzy logic mode switching in helicopters

The application of fuzzy logic to a wide range of control problems has been gaining momentum internationally, fueled by a concentrated Japanese effort. Advanced Research & Development within the Engineering Department at Sikorsky Aircraft undertook a fuzzy logic research effort designed to evaluate how effective fuzzy logic control might be in relation to helicopter operations. The mode switching module in the advanced flight control portion of Sikorsky's motion based simulator was identified as a good candidate problem because it was simple to understand and contained imprecise (fuzzy) decision criteria. The purpose of the switching module is to aid a helicopter pilot in entering and leaving coordinated turns while in flight. The criteria that determine the transitions between modes are imprecise and depend on the varied ranges of three flight conditions (i.e., simulated parameters): Commanded Rate, Duration, and Roll Attitude. The parameters were given fuzzy ranges and used as input variables to a fuzzy rulebase containing the knowledge of mode switching. The fuzzy control program was integrated into a real time interactive helicopter simulation tool. Optimization of the heading hold and turn coordination was accomplished by interactive pilot simulation testing of the handling quality performance of the helicopter dynamic model. The fuzzy logic code satisfied all the requirements of this candidate control problem.

Sherman, Porter D.↗

NASA NTRS1996

Validation of UARS Microwave Limb Sounder Ozone Measurements

This paper describes the validation of ozone data from the Upper Atmosphere Research Satellite (UARS) Microwave Limb Sounder (MLS). The MLS ozone retrievals are obtained from the calibrated microwave radiances (emission spectra) in two separate bands, at frequencies near 205 and 183 GHz. Analyses described here focus on the MLS Version 3 data (the first set of files made publicly available). We describe results of simulations performed to assess the quality of the retrieval algorithms, in terms of both mixing ratio and radiance closure. From actual MLS observations, the 205-GHz ozone retrievals give better closure (smaller radiance residuals) than that from the 183-GHz measurements and should be considered more accurate from the calibration aspects. However, the 183-GHz data are less noise limited in the mesosphere and can provide the most useful scientific results in that region. We compare the retrieved 205-GHz ozone profiles in the middle-to lower stratosphere to ozonesonde measurements at a wide range of latitudes and seasons. Ground-based lidar data from Table Mountain, California, provide a good reference for comparisons at higher altitudes. Based on these analyses, comparisons with balloon-borne measurements and others, as well as a detailed budget of estimated uncertainties, MLS results appear to be generally of high quality, with some biases worth mentioning. Results for the lowermost stratosphere (approx. 50 to 100 bPa) are still in need of improvement. A set of estimated precision and accuracy values is derived for the MLS ozone data sets. We also comment on recent updates in the retrieval algorithms and their impact on ozone values.

Froidevaux, L.↗

NASA NTRS2003

Integration of Online Parameter Identification and Neural Network for In-Flight Adaptive Control

An indirect adaptive system has been constructed for robust control of an aircraft with uncertain aerodynamic characteristics. This system consists of a multilayer perceptron pre-trained neural network, online stability and control derivative identification, a dynamic cell structure online learning neural network, and a model following control system based on the stochastic optimal feedforward and feedback technique. The pre-trained neural network and model following control system have been flight-tested, but the online parameter identification and online learning neural network are new additions used for in-flight adaptation of the control system model. A description of the modification and integration of these two stand-alone software packages into the complete system in preparation for initial flight tests is presented. Open-loop results using both simulation and flight data, as well as closed-loop performance of the complete system in a nonlinear, six-degree-of-freedom, flight validated simulation, are analyzed. Results show that this online learning system, in contrast to the nonlearning system, has the ability to adapt to changes in aerodynamic characteristics in a real-time, closed-loop, piloted simulation, resulting in improved flying qualities.

Hageman, Jacob↗

NASA NTRS2003

Integration of Online Parameter Identification and Neural Network for In-Flight Adaptive Control

An indirect adaptive system has been constructed for robust control of an aircraft with uncertain aerodynamic characteristics. This system consists of a multilayer perceptron pre-trained neural network, online stability and control derivative identification, a dynamic cell structure online learning neural network, and a model following control system based on the stochastic optimal feedforward and feedback technique. The pre-trained neural network and model following control system have been flight-tested, but the online parameter identification and online learning neural network are new additions used for in-flight adaptation of the control system model. A description of the modification and integration of these two stand-alone software packages into the complete system in preparation for initial flight tests is presented. Open-loop results using both simulation and flight data, as well as closed-loop performance of the complete system in a nonlinear, six-degree-of-freedom, flight validated simulation, are analyzed. Results show that this online learning system, in contrast to the nonlearning system, has the ability to adapt to changes in aerodynamic characteristics in a real-time, closed-loop, piloted simulation, resulting in improved flying qualities.

Hageman, Jacob J.↗

NASA NTRS2004

Selected Flight Test Results for Online Learning Neural Network-Based Flight Control System

The NASA F-15 Intelligent Flight Control System project team has developed a series of flight control concepts designed to demonstrate the benefits of a neural network-based adaptive controller. The objective of the team is to develop and flight-test control systems that use neural network technology to optimize the performance of the aircraft under nominal conditions as well as stabilize the aircraft under failure conditions. Failure conditions include locked or failed control surfaces as well as unforeseen damage that might occur to the aircraft in flight. This report presents flight-test results for an adaptive controller using stability and control derivative values from an online learning neural network. A dynamic cell structure neural network is used in conjunction with a real-time parameter identification algorithm to estimate aerodynamic stability and control derivative increments to the baseline aerodynamic derivatives in flight. This set of open-loop flight tests was performed in preparation for a future phase of flights in which the learning neural network and parameter identification algorithm output would provide the flight controller with aerodynamic stability and control derivative updates in near real time. Two flight maneuvers are analyzed a pitch frequency sweep and an automated flight-test maneuver designed to optimally excite the parameter identification algorithm in all axes. Frequency responses generated from flight data are compared to those obtained from nonlinear simulation runs. An examination of flight data shows that addition of the flight-identified aerodynamic derivative increments into the simulation improved the pitch handling qualities of the aircraft.

Williams, Peggy S.↗

NASA NTRS2004

Selected Flight Test Results for Online Learning Neural Network-Based Flight Control System

The NASA F-15 Intelligent Flight Control System project team developed a series of flight control concepts designed to demonstrate neural network-based adaptive controller benefits, with the objective to develop and flight-test control systems using neural network technology to optimize aircraft performance under nominal conditions and stabilize the aircraft under failure conditions. This report presents flight-test results for an adaptive controller using stability and control derivative values from an online learning neural network. A dynamic cell structure neural network is used in conjunction with a real-time parameter identification algorithm to estimate aerodynamic stability and control derivative increments to baseline aerodynamic derivatives in flight. This open-loop flight test set was performed in preparation for a future phase in which the learning neural network and parameter identification algorithm output would provide the flight controller with aerodynamic stability and control derivative updates in near real time. Two flight maneuvers are analyzed - pitch frequency sweep and automated flight-test maneuver designed to optimally excite the parameter identification algorithm in all axes. Frequency responses generated from flight data are compared to those obtained from nonlinear simulation runs. Flight data examination shows that addition of flight-identified aerodynamic derivative increments into the simulation improved aircraft pitch handling qualities.

Williams-Hayes, Peggy S.↗

NASA NTRS2010

HOPE: An On-Line Piloted Handling Qualities Experiment Data Book

A novel on-line database for capturing most of the information obtained during piloted handling qualities experiments (either flight or simulated) is described. The Hyperlinked Overview of Piloted Evaluations (HOPE) web application is based on an open-source object-oriented Web-based front end (Ruby-on-Rails) that can be used with a variety of back-end relational database engines. The hyperlinked, on-line data book approach allows an easily-traversed way of looking at a variety of collected data, including pilot ratings, pilot information, vehicle and configuration characteristics, test maneuvers, and individual flight test cards and repeat runs. It allows for on-line retrieval of pilot comments, both audio and transcribed, as well as time history data retrieval and video playback. Pilot questionnaires are recorded as are pilot biographies. Simple statistics are calculated for each selected group of pilot ratings, allowing multiple ways to aggregate the data set (by pilot, by task, or by vehicle configuration, for example). Any number of per-run or per-task metrics can be captured in the database. The entire run metrics dataset can be downloaded in comma-separated text for further analysis off-line. It is expected that this tool will be made available upon request

Jackson, E. B.↗

NASA NTRS2011

Nonlinear Dynamic Inversion Baseline Control Law: Architecture and Performance Predictions

A model reference dynamic inversion control law has been developed to provide a baseline control law for research into adaptive elements and other advanced flight control law components. This controller has been implemented and tested in a hardware-in-the-loop simulation; the simulation results show excellent handling qualities throughout the limited flight envelope. A simple angular momentum formulation was chosen because it can be included in the stability proofs for many basic adaptive theories, such as model reference adaptive control. Many design choices and implementation details reflect the requirements placed on the system by the nonlinear flight environment and the desire to keep the system as basic as possible to simplify the addition of the adaptive elements. Those design choices are explained, along with their predicted impact on the handling qualities.

Miller, Christopher J.↗

NASA NTRSDate not supplied

Habitability Assessments And Lessons-learned From 3-day And 11-day Enriched Oxygen Hypobaric Chamber Tests At NASA Johnson Space Center

INTRODUCTION: Decompression sickness (DCS) is a risk to the health and performance of astronauts and high-altitude aircrew. Tolerance to flammability, hypoxia, prebreathe duration, and DCS risk varies across different organizations, vehicles, suits, and destinations, necessitating a variety of DCS risk mitigation approaches. Existing models of altitude DCS risk are often insufficient to enable accurate risk-informed decisions during hardware development, mission planning, and flight operations. METHODS: NASA completed outfitting of a dedicated facility at Johnson Space Center to support testing of up to eight human subjects for multiple days in hypobaric and enriched oxygen atmospheres. The primary purpose of the testing capability is validation of DCS risk mitigation protocols for Artemis missions to the Moon; however, it will also support development and validation of a generalizable altitude DCS risk estimation tool. A 3-day and an 11-day prebreathe validation test were completed in 2022, each with 8 human subjects living at 56.5 kPa (8.2 psia), 34% O2, 66% N2, with 5 simulated EVAs performed on masks at 29.6 kPa (4.3 psi), 85% O2, 15% N2. Facility and organizational lessons-learned and process improvements were recorded during and following the tests, and subjective habitability ratings were recorded daily during the 11-day test. Hypoxia and DCS-related physiological and cognitive outcome measures were recorded during both tests and are reported in companion presentations. RESULTS & DISCUSSION: All subjects completed each of the tests. Primary habitability issues related to mask discomfort during simulated EVAs and poor sleep quality due to thin mattresses. Polybenzimidazole (PBI) clothing was worn by all subjects due to the increased fire risk and may be required for Artemis missions; clothing was found to be acceptable overall with the worst ratings being due to poor fit and inelasticity. Chamber O2 and CO2 sensor inconsistency was observed that did not result in test termination but required post-test follow-up. Forward plans include additional hypobaric testing and integration of existing and future physiological outcome data into an open-source Aerospace Estimation Tool for Hypobaric Exposure Risk (AETHER). NASA is also working to make the testing capability available to commercial companies.

Andrew F J Abercromby↗

NASA NTRSDate not supplied

Habitability Assessments And Lessons-learned From 3-day And 11-day Enriched Oxygen Hypobaric Chamber Tests At NASA Johnson Space Center

INTRODUCTION: Decompression sickness (DCS) is a risk to the health and performance of astronauts and high-altitude aircrew. Tolerance to flammability, hypoxia, prebreathe duration, and DCS risk varies across different organizations, vehicles, suits, and destinations, necessitating a variety of DCS risk mitigation approaches. Existing models of altitude DCS risk are often insufficient to enable accurate risk-informed decisions during hardware development, mission planning, and flight operations. METHODS: NASA completed outfitting of a dedicated facility at Johnson Space Center to support testing of up to eight human subjects for multiple days in hypobaric and enriched oxygen atmospheres. The primary purpose of the testing capability is validation of DCS risk mitigation protocols for Artemis missions to the Moon; however, it will also support development and validation of a generalizable altitude DCS risk estimation tool. A 3-day and an 11-day prebreathe validation test were completed in 2022, each with 8 human subjects living at 56.5 kPa (8.2 psia), 34% O2, 66% N2, with 5 simulated EVAs performed on masks at 29.6 kPa (4.3 psi), 85% O2, 15% N2. Facility and organizational lessons-learned and process improvements were recorded during and following the tests, and subjective habitability ratings were recorded daily during the 11-day test. Hypoxia and DCS-related physiological and cognitive outcome measures were recorded during both tests and are reported in companion presentations. RESULTS & DISCUSSION: All subjects completed each of the tests. Primary habitability issues related to mask discomfort during simulated EVAs and poor sleep quality due to thin mattresses. Polybenzimidazole (PBI) clothing was worn by all subjects due to the increased fire risk and may be required for Artemis missions; clothing was found to be acceptable overall with the worst ratings being due to poor fit and inelasticity. Chamber O2 and CO2 sensor inconsistency was observed that did not result in test termination but required post-test follow-up. Forward plans include additional hypobaric testing and integration of existing and future physiological outcome data into an open-source Aerospace Estimation Tool for Hypobaric Exposure Risk (AETHER). NASA is also working to make the testing capability available to commercial companies.

Andrew Abercromby↗

NASA NTRSDate not supplied

Advancing Electric Propulsion Aircraft Evaluation for Urban Air Mobility: Insights from NASA-Ames

This presentation delves into a recent evaluation conducted at NASA-Ames on the Vertical Motion Simulator, focusing on the handling qualities of Distributed Electric Propulsion VTOL (eVTOL) aircraft, specifically tailored for Urban Air Mobility (UAM) applications. The presentation will focus on the recent effort to adapt and refine use of the Aeronautical Design Standard -33 (ADS-33) rotorcraft handling qualities developed by the U.S. Army and NASA to meet the diverse needs of civilian (eVTOL) concept evaluation. A brief discussion of the author’s personal test pilot insights in the early development of military Fly-By-Wire evaluation methods will also be provided. The emergence of innovative eVTOL designs with unique lift capabilities and flight control systems, present both opportunities and challenges, particularly in ensuring safety amidst technological complexity. To navigate these challenges, our investigation examined evaluation criteria designed to accommodate the varied configurations and advanced automation systems inherent in modern eVTOL aircraft. By establishing a standardized approach to evaluation, our research not only fosters innovation but also upholds safety standards in the dynamic landscape of urban air mobility. Through this endeavor, we help to facilitate the seamless integration of novel aircraft capabilities into new operations, contributing to a new era of safe and efficient aerial transportation.

Loran Allen Haworth↗